Commit graph

1,058,063 commits

Author SHA1 Message Date
Hans Verkuil
4108b3e6db media: v4l2-dv-timings.c: fix wrong condition in two for-loops
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.

The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:52 +02:00
Martin Kepplinger
f33fd8d77d media: imx: add a driver for i.MX8MQ mipi csi rx phy and controller
Add a driver to support the i.MX8MQ MIPI CSI receiver. The hardware side
is based on
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.70_2.3.0

It's built as part of VIDEO_IMX7_CSI because that's documented to support
i.MX8M platforms. This driver adds i.MX8MQ support where currently only the
i.MX8MM platform has been supported.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:52 +02:00
Martin Kepplinger
37255747ec media: dt-bindings: media: document the nxp,imx8mq-mipi-csi2 receiver phy and controller
The i.MX8MQ SoC integrates a different MIPI CSI receiver as the i.MX8MM so
describe the DT bindings for it.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Tom Rix
43c3f12dfb media: imx: imx7_mipi_csis: convert some switch cases to the default
Static analysis reports this false positive
imx7-mipi-csis.c:1027:2: warning: 4th function call argument is
  an uninitialized value

The variable 'align' is falsely reported as uninitialized.
Even though all the cases are covered in the
	switch (csis_fmt->width % 8) {

Because there is no default case, it is reported as uninialized.

Improve the switch by converting the most numerous set of cases
to the default and silence the false positive.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Laurent Pinchart
0ada1697ed media: imx: imx7-media-csi: Fix buffer return upon stream start failure
When the stream fails to start, the first two buffers in the queue have
been moved to the active_vb2_buf array and are returned to vb2 by
imx7_csi_dma_unsetup_vb2_buf(). The function is called with the buffer
state set to VB2_BUF_STATE_ERROR unconditionally, which is correct when
stopping the stream, but not when the start operation fails. In that
case, the state should be set to VB2_BUF_STATE_QUEUED. Fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Laurent Pinchart
8b226173a1 media: imx: imx7-media-csi: Don't set PIXEL_BIT in CSICR1
The PIXEL_BIT field of the CSICR1 register is documented as setting the
Bayer data width to 10 bits, and is set by the driver for all non-YUV
pixel formats. Test code from NXP showed that the bit shouldn't be set
for Bayer formats, and this was confirmed by experimentation with RAW8
capture (which doesn't work when setting the field) and RAW10 capture
(for which setting the field doesn't seem to make a difference) on
i.MX8MM with an OV5640 sensor connected over CSI-2. Don't set it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Laurent Pinchart
a581c87c68 media: imx: imx7-media-csi: Set TWO_8BIT_SENSOR for >= 10-bit formats
Sample code from NXP, as well as experiments on i.MX8MM with RAW10
capture with an OV5640 sensor connected over CSI-2, showed that the
TWO_8BIT_SENSOR field of the CSICR3 register needs to be set for formats
larger than 8 bits. Do so, even if the reference manual doesn't clearly
describe the effect of the field.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Laurent Pinchart
e8713c31f8 media: dt-bindings: media: nxp,imx7-csi: Add i.MX8MM support
The i.MX8MM integrates a CSI bridge IP core, as the i.MX7. There seems
to be no difference between the two SoCs according to the reference
manual, but as documentation may not be accurate, add a compatible
string for the i.MX8MM, with a fallback on the compatible i.MX7.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Umang Jain
f809665ee7 media: imx258: Limit the max analogue gain to 480
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:

	Gain = 512 / (512 – X)

Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.

Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.

Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Laurent Pinchart
51f93add36 media: imx258: Rectify mismatch of VTS value
The frame_length_lines (0x0340) registers are hard-coded as follows:

- 4208x3118
  frame_length_lines = 0x0c50

- 2104x1560
  frame_length_lines = 0x0638

- 1048x780
  frame_length_lines = 0x034c

The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:

  #define IMX258_VTS_30FPS                0x0c98
  #define IMX258_VTS_30FPS_2K             0x0638
  #define IMX258_VTS_30FPS_VGA            0x034c

There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Bingbu Cao
d84a2e4900 media: ov8856: ignore gpio and regulator for ov8856 with ACPI
For ov8856 working with ACPI, it does not depend on the reset gpio
and regulator to do reset and power control, so should get the gpio
and regulator for non-ACPI cases only, otherwise it will break ov8856
with ACPI.

[Sakari Ailus: Wrap a line over 80 chars.]

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Cc: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Bingbu Cao
0e2b855266 media: ov9734: use group write for digital gain
As the RGB digital gains of ov9734 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Bingbu Cao
84363509c7 media: ov2740: use group write for digital gain
As the RGB digital gains of ov2740 were not applied as group, some
artifacts were observed in low light environment, use group write for
digital gain can make the RGB digital can be guaranteed to applied
together at frame boundary.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Sakari Ailus
4d7adf0236 media: v4l2-flash: Check whether setting LED brightness succeeded
Setting LED brightness may return an error but the return value was never
checked by the V4L2 flash LED class. Do it now.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Sakari Ailus
a40eba9b26 media: v4l2-flash: Add sanity checks for flash and indicator controls
The V4L2 flash API supports combinations of indicator and flash LEDs. Due
to this, there's a fair amount of code that deals with all the possible
options and just reading one part of the file doesn't really tell which
combinations are really possible.

Make the checks more explicit to keep static analysers happy and to make
the code more resilient to future mishaps.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Sakari Ailus
41a95d043f media: ccs: Implement support for manual LP control
Use the pre_streamon callback to transition the transmitter to either
LP-11 or LP-111 mode if supported by the sensor.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Sakari Ailus
253171a0da media: v4l: subdev: Add pre_streamon and post_streamoff callbacks
Add pre_streamon and post_streamoff callbacks that can be used to set a
CSI-2 transmitter to LP-11 or LP-111 mode. This can be used by receiver
drivers to reliably initialise the receiver when its initialisation
requires software involvement.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:51 +02:00
Sakari Ailus
013c35b22e media: Documentation: v4l: Rework LP-11 documentation, add callbacks
Rework LP-11 and LP-111 mode documentation to make it more understandable
and useful. This involves adding pre_streamon and post_streamon callbacks
that make it possible to explicitly transition the transmitter to either
mode.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Sakari Ailus
e5a466d4bc media: Documentation: v4l: Improve frame rate configuration documentation
Improve the documentation of the frame rate configuration so that it can
be understood by a regular human being.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Sakari Ailus
8925b53083 media: Documentation: v4l: Fix V4L2_CID_PIXEL_RATE documentation
The V4L2_CID_PIXEL_RATE is nowadays used to tell pixel sampling rate in
the sub-device's pixel array, not the pixel rate over a link (for which it
also becomes unfit with the addition of multiplexed streams later on). Fix
this.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Sakari Ailus
6f8f9fdec8 media: Documentation: media: Fix v4l2-async kerneldoc syntax
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Sakari Ailus
b9a5433642 media: Documentation: media: Improve camera sensor documentation
Modernise the documentation to make it more precise and update the use of
pixel rate control and various other changes. In particular:

- Use non-proportional font for file names, properties as well as
  controls.

- The unit of the HBLANK control is pixels, not lines.

- The unit of PIXEL_RATE control is pixels per second, not Hz.

- Merge common requirements for CSI-2 and parallel busses.

- Include all DT properties needed for assigned clocks.

- Fix referencing the link rate control.

- SMIA driver's new name is CCS driver.

- The PIXEL_RATE control denotes pixel rate on the pixel array on camera
  sensors. Do not suggest it is used to tell the maximum pixel rate on the
  bus anymore.

- Improve ReST syntax (plain struct and function names).

- Remove the suggestion to use s_power() in receiver drivers.

- Make MIPI website URL use HTTPS, add Wikipedia links to BT.601 and
  BT.656.

Fixes: e4cf8c58af ("media: Documentation: media: Document how to write camera sensor drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Wei Yongjun
0368e7d2cd media: omap3isp: Fix missing unlock in isp_subdev_notifier_complete()
Add the missing unlock before return from function
isp_subdev_notifier_complete() in the init error
handling case.

Fixes: ba689d9333 ("media: omap3isp: Acquire graph mutex for graph traversal")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Zhen Lei
e006558fa4 media: exynos4-is: use DEVICE_ATTR_RW() helper macro
Use DEVICE_ATTR_RW() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.

Due to the names of the read and write functions of the sysfs attribute is
normalized, there is a natural association.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Zhen Lei
9256de0694 media: i2c: use DEVICE_ATTR_RO() helper macro
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.

Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Zhen Lei
5fca4169f5 media: i2c: et8ek8: use DEVICE_ATTR_RO() helper macro
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.

Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Zhen Lei
7b537f290a media: mc-device.c: use DEVICE_ATTR_RO() helper macro
Use DEVICE_ATTR_RO() helper macro instead of DEVICE_ATTR(), which is
simpler and more readable.

Due to the name of the read function of the sysfs attribute is normalized,
there is a natural association.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Xavier Roumegue
1536fbdbcb media: ov5640: Complement yuv mbus formats with their 1X16 versions
According to media bus pixel codes definition, data formats on serial
busses should be described with one bus sample per pixel.

Documentation/userspace-api/media/v4l/subdev-formats.rst states:

"The media bus pixel codes document parallel formats. Should the pixel
data be transported over a serial bus, the media bus pixel code that
describes a parallel format that transfers a sample on a single clock
cycle is used. For instance, both MEDIA_BUS_FMT_BGR888_1X24 and
MEDIA_BUS_FMT_BGR888_3X8 are used on parallel busses for transferring an
8 bits per sample BGR data, whereas on serial busses the data in this
format is only referred to using MEDIA_BUS_FMT_BGR888_1X24. This is
because there is effectively only a single way to transport that
format on the serial busses."

Some MIPI CSI receivers strictly obey this definition and declare
support for only *1X_* formats.

Hence, complement the supported media bus formats with their 1X16 versions
(currently applicable to yuyv, uyvy) to enhance interoperability with CSI
receivers.

Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Martina Krasteva
14ea315bbe media: i2c: Add ov9282 camera sensor driver
Add a v4l2 sub-device driver for the OmniVisison ov9282
black&white image sensor.
The camera sensor uses the i2c bus for control and the
csi-2 bus for data.

The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
    - 1280x720 @ 30fps

[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Martina Krasteva
4874ea3987 media: dt-bindings: media: Add bindings for ov9282
- Add dt-bindings documentation for OmniVision ov9282 sensor driver
- Add MAINTAINERS entry for OmniVision ov9282 binding documentation

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Martina Krasteva
9214e86c0c media: i2c: Add imx412 camera sensor driver
Add a v4l2 sub-device driver for the Sony imx412 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.

The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
    - 4056x3040 @ 30fps
- supported bayer order output:
    - SRGGB10

[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:50 +02:00
Martina Krasteva
333b3125d1 media: dt-bindings: media: Add bindings for imx412
- Add dt-bindings documentation for Sony imx412 sensor driver
- Add MAINTAINERS entry for Sony imx412 binding documentation

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Martina Krasteva
45d19b5fb9 media: i2c: Add imx335 camera sensor driver
Add a v4l2 sub-device driver for the Sony imx335 image sensor.
ThE camera sensor uses the i2c bus for control and the csi-2
bus for data.

The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
	- 2592x1940 @ 30fps
- supported bayer order output:
	- SRGGB12

[Sakari Ailus: Rebase on commit c802a4174beeb25cb539c806c9d0d3c0f61dfa53.]

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Martina Krasteva
932741d451 media: dt-bindings: media: Add bindings for imx335
- Add dt-bindings documentation for Sony imx335 sensor driver
- Add MAINTAINERS entry for Sony imx335 binding documentation

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Paul Kocialkowski
c3609c45b7 media: v4l2-subdev: Fix documentation of the subdev_notifier member
Fix the name of the function that registers the subdev_notifier member
of the v4l2_subdev structure.

[Sakari Ailus: Drop _sensor from the function name.]

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Dongliang Mu
6fa54bc713 media: em28xx-input: fix refcount bug in em28xx_usb_disconnect
If em28xx_ir_init fails, it would decrease the refcount of dev. However,
in the em28xx_ir_fini, when ir is NULL, it goes to ref_put and decrease
the refcount of dev. This will lead to a refcount bug.

Fix this bug by removing the kref_put in the error handling code
of em28xx_ir_init.

refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.13.0 #3
Workqueue: usb_hub_wq hub_event
RIP: 0010:refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Call Trace:
  kref_put.constprop.0+0x60/0x85 include/linux/kref.h:69
  em28xx_usb_disconnect.cold+0xd7/0xdc drivers/media/usb/em28xx/em28xx-cards.c:4150
  usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
  __device_release_driver drivers/base/dd.c:1201 [inline]
  device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1232
  bus_remove_device+0x108/0x160 drivers/base/bus.c:529
  device_del+0x1fe/0x510 drivers/base/core.c:3540
  usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
  usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2221
  hub_port_connect drivers/usb/core/hub.c:5151 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5440 [inline]
  port_event drivers/usb/core/hub.c:5586 [inline]
  hub_event+0xf81/0x1d40 drivers/usb/core/hub.c:5668
  process_one_work+0x2c9/0x610 kernel/workqueue.c:2276
  process_scheduled_works kernel/workqueue.c:2338 [inline]
  worker_thread+0x333/0x5b0 kernel/workqueue.c:2424
  kthread+0x188/0x1d0 kernel/kthread.c:319
  ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295

Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: ac56886371 ("media: em28xx: Fix possible memory leak of em28xx struct")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Viktor Prutyanov
49be1c78d5 media: rc: introduce Meson IR TX driver
This patch adds the driver for Amlogic Meson IR transmitter.

Some Amlogic SoCs such as A311D and T950D4 have IR transmitter
(also called blaster) controller onboard. It is capable of sending
IR signals with arbitrary carrier frequency and duty cycle.

The driver supports 2 modulation clock sources:
 - xtal3 clock (xtal divided by 3)
 - 1us clock

Signed-off-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Viktor Prutyanov
e9f504f7b5 media: rc: meson-ir-tx: document device tree bindings
This patch adds binding documentation for the IR transmitter
available in Amlogic Meson SoCs.

Signed-off-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-08-04 14:43:49 +02:00
Arnd Bergmann
8e816b9915 AT91 dt for 5.15:
- add sama7g5 SoC and associated evaluation kit, the sama7g5-ek
 - adaptation of some DT for sama5d27 som1 ek, sama5d4 xplained and
   sama5d2 icp boards
 - fixes to gpio and shutdown controller nodes for all boards
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYQpSOAAKCRAfOrpwrNPN
 DJOsAP0XC3docVgm+Bw+EZH/FgoIQQCaKcBjx23IhjhWXPx6rwD9Hvze215rDL5V
 YH41Nuq2nDAd5xl3/S0mJIjlupo3RgQ=
 =OhbX
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEKiKQACgkQmmx57+YA
 GNnfRhAAijy8RW+Nfo09sKyxdZMfuv+Sh44HA0cUhWtUNrtWWL4ZslY+D3Sv2uHs
 PnIwrvoSDzbGZmfn3fI0QDv6DBpTItMvspEsrd8jx8fWVcBkHGbyKjmj+k62GR/3
 2e/QL5bw8zq0mM33GXODgVyqFok3RF3BQ1R0uXU6d0Z/D638E3EjNLJ7B6XiOsO8
 OdiXZnwSmYTIpplrk+IhOLlEv1XTy1TLcbtlKuSPPdNBBAQZ8J1enzGNArV90aYO
 JcYDZsmcUXmC8Qm3hPu5r6N/8XGWSz4v3/2FvA0oAOrTB1cDUFFKJ3nn+8uRgPuy
 c+86vIdFaDaAUJkoSa6Nq2DvSCLrRVi2C6HHMMOVTA2IqxcNpy+RN4VsEuNdQkbo
 tQlqqFsgULs/dWD63VNEasyKVomhUi3FRUAQh01i0LzYiaqEmeK3g3gOyRQROEcu
 OzhYBWRktQjzWwHwrOs1a6qWpe6Uc6jrW9vnehccd+4/iIYrxMQmRq21aVDGC8b8
 sbeWTJuo301ySx0t32aw3jUj6s0YlGz8aL/O2bho5KX0nWHgKA+onRQXPDmfh0fu
 UbeN6I/IriuVchoDY2w3VAS5fMyMok2tk7BhTOVYjVwhjYePrngceXew25qfCs80
 b7M07RllA3uWSN2C7TSd0c9Da71JTtxYIFiO7Dm5ylKm9BAzr/A=
 =tynn
 -----END PGP SIGNATURE-----

Merge tag 'at91-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt

AT91 dt for 5.15:

- add sama7g5 SoC and associated evaluation kit, the sama7g5-ek
- adaptation of some DT for sama5d27 som1 ek, sama5d4 xplained and
  sama5d2 icp boards
- fixes to gpio and shutdown controller nodes for all boards

* tag 'at91-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: at91: use the right property for shutdown controller
  ARM: dts: at91: sama5d2_icp: enable digital filter for I2C nodes
  ARM: dts: at91: sama5d4_xplained: change the key code of the gpio key
  ARM: dts: at91: add conflict note for d3
  ARM: dts: at91: add pinctrl-{names, 0} for all gpios
  ARM: dts: at91: sama5d27_som1_ek: enable ADC node
  ARM: dts: at91: sama5d4_xplained: Remove spi0 node
  dt-bindings: atmel-sysreg: add bindings for sama7g5
  ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek
  dt-bindings: ARM: at91: document sama7g5ek board

Link: https://lore.kernel.org/r/20210804085000.13233-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-04 14:31:32 +02:00
Arnd Bergmann
72ee3b4dc2 Ux500 Device Tree updates for the v5.15 kernel cycle:
- New device trees for these mobile phones:
   - Samsung Gavini
   - Samsung Codina
   - Samsung Kyle
 - Flag eMMC cards as non-SD non-SDIO to save time
 - Link USB PHY to USB controller in the device tree
 - Fix up the operating points to the actual clock frequencies
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmEJNBcACgkQQRCzN7AZ
 XXPiEg//f4j8kXx378712gZHS3niZTkYh2Vu7onxo288b8JZ0ZjSQwvx6f2y479O
 SQKrn72lU/rguHbOTZ++73A3XUNTWsLQYgaNB2CmUnwQ5lvMfD7/ajCtc7Pyg/29
 t4a8ZYN7T1DjLa9LDpn3nuc1AAqQOnpU8XS8yPKz1k1ApnYg/wqd2LZEelHeYFwJ
 QjR7kdpJL3LF91dtsGu38f3VGOx8dTTH4VP4FM5U9bSL6jtGbJJlzbKCTJV7YyEm
 7DLUXiuQ/1rw8WU/o7nA0FbRKtinYt3Yj843oRChuRjTS28CZvQUIN1OERujaylA
 oNebCR5EE4HRl1HVNnLIBMcEQ4QYR9Bk0Ek2V6t7ihEaRQYbVO4I1m+FkCTdXaPz
 RsHR/fcEhZVKEeGYEsvz6HuTAGzFC/Ju1AwoTO4gambDnv3ejLApjtLkFVNR5mrx
 QVf4GOicmZbgTtzfQZ+X1v+bxkuNTMJaDDFOnX2aMrxv/oeW4B4e2cxIQ2JRqOrA
 baQ78zb1Ar1J/xxACiEOSRyrQw3SNOerHQAePHhes47/b/0oAYywvLXKb59FJyLX
 3tk0fQ5b5Yhz+FA09coTfpw8GgjMnJCodZO3aoCz1FEgVhFyjETBEhZMFjGt8+Nr
 bJuhCiraPspGwj81URMhPcQ+HKVpfp7+A/Ot2ueu86L2YCzZUR0=
 =iBYE
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEKiGUACgkQmmx57+YA
 GNmk8Q/+Nmd8xEef4lRZDdoOU30bcgbImOHTTFZ6oyTrDyEIM2KZ4VqDr6yI/A/F
 QILKi/GE4CGaPmebmYw+KG2dN1ZClRWywKKHUHUbaqGJKyuR17CxYMdBJYmWTfyN
 QOiIrjYjUONfzr9mYbk/DCYZAwwrVyawV5kNJtbfCXtvS0VsPqt8/CAupviPBm+N
 hzqikMX0RTWIjm9zOtakLg2uzars9rV6iKiUw3gO7gACj8ik3FR5FTxijo4p5X1n
 resPiYtEwBaqS5a4LXl6xX7grp6m4lcCOvHx6lk4BhRvkNG0d0JOW/xsPnDABfhU
 dB9loFXVfm5sNaQAiG+QkE0F/f9Bbc7+6ED/+uod0R5oNqOF1P5iAk75xWXRVIvC
 vC3ZoFqgAO1LujUaa7omfr31i/8y2MuSJf6v1l/9hm6zlwH6e2Z76Jgu2GEaup/z
 HoVwr3LATY4toqpXFW4xTxYKneO8rlTmvSGLrO5qwem9fgpwjgwWzdE/aOx2TrqO
 hsByw/cN2RpQShhpU6SyuHF0TGIn2Xqp8DkvQA2msO+F5fEqL3tKF0LvGiQAGf6v
 ujB+w5MjTDN68pDotv0ykAtNDAdp8Y6Re3S4RWPceY6A8mEZXz4vrunAulKYQbfw
 38DBz/IKGL5yqCCBCbci1C0rGi5AfBBhFZBC9kredp5z4CE+FPU=
 =xBsz
 -----END PGP SIGNATURE-----

Merge tag 'ux500-dts-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

Ux500 Device Tree updates for the v5.15 kernel cycle:

- New device trees for these mobile phones:
  - Samsung Gavini
  - Samsung Codina
  - Samsung Kyle
- Flag eMMC cards as non-SD non-SDIO to save time
- Link USB PHY to USB controller in the device tree
- Fix up the operating points to the actual clock frequencies

* tag 'ux500-dts-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: ux500: Adjust operating points to reality
  ARM: dts: ux500: Add a device tree for Kyle
  ARM: dts: ux500: Add devicetree for Codina
  ARM: dts: ux500: ab8500: Link USB PHY to USB controller node
  ARM: dts: ux500: Flag eMMCs as non-SDIO/SD
  ARM: dts: ux500: Add device tree for Samsung Gavini

Link: https://lore.kernel.org/r/CACRpkdbjBv5ywZZD8rK07d5sLcHsG8o4iYD-3jHO=HLg6-nKnA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-04 14:30:29 +02:00
Takashi Iwai
f2553d4678
ASoC: amd: vangogh: Drop superfluous mmap callback
The mmap callback of vangogh driver just calls the default mmap
handler, and it's superfluous, as the PCM core would call it if not
set.  Let's drop the superfluous mmap callback.

Fixes: 361414dc1f ("ASoC: amd: add vangogh i2s dma driver pm ops")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210804075223.9823-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-08-04 13:20:14 +01:00
Marc Zyngier
47e6223c84 KVM: arm64: Unregister HYP sections from kmemleak in protected mode
Booting a KVM host in protected mode with kmemleak quickly results
in a pretty bad crash, as kmemleak doesn't know that the HYP sections
have been taken away. This is specially true for the BSS section,
which is part of the kernel BSS section and registered at boot time
by kmemleak itself.

Unregister the HYP part of the BSS before making that section
HYP-private. The rest of the HYP-specific data is obtained via
the page allocator or lives in other sections, none of which is
subjected to kmemleak.

Fixes: 90134ac9ca ("KVM: arm64: Protect the .hyp sections from the host")
Reviewed-by: Quentin Perret <qperret@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 5.13
Link: https://lore.kernel.org/r/20210802123830.2195174-3-maz@kernel.org
2021-08-04 13:10:47 +01:00
Marc Zyngier
eb48d154cd arm64: Move .hyp.rodata outside of the _sdata.._edata range
The HYP rodata section is currently lumped together with the BSS,
which isn't exactly what is expected (it gets registered with
kmemleak, for example).

Move it away so that it is actually marked RO. As an added
benefit, it isn't registered with kmemleak anymore.

Fixes: 380e18ade4 ("KVM: arm64: Introduce a BSS section for use at Hyp")
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org #5.13
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210802123830.2195174-2-maz@kernel.org
2021-08-04 13:09:20 +01:00
Praveen Kumar
e5d9b714fe x86/hyperv: fix root partition faults when writing to VP assist page MSR
For root partition the VP assist pages are pre-determined by the
hypervisor. The root kernel is not allowed to change them to
different locations. And thus, we are getting below stack as in
current implementation root is trying to perform write to specific
MSR.

    [ 2.778197] unchecked MSR access error: WRMSR to 0x40000073 (tried to write 0x0000000145ac5001) at rIP: 0xffffffff810c1084 (native_write_msr+0x4/0x30)
    [ 2.784867] Call Trace:
    [ 2.791507] hv_cpu_init+0xf1/0x1c0
    [ 2.798144] ? hyperv_report_panic+0xd0/0xd0
    [ 2.804806] cpuhp_invoke_callback+0x11a/0x440
    [ 2.811465] ? hv_resume+0x90/0x90
    [ 2.818137] cpuhp_issue_call+0x126/0x130
    [ 2.824782] __cpuhp_setup_state_cpuslocked+0x102/0x2b0
    [ 2.831427] ? hyperv_report_panic+0xd0/0xd0
    [ 2.838075] ? hyperv_report_panic+0xd0/0xd0
    [ 2.844723] ? hv_resume+0x90/0x90
    [ 2.851375] __cpuhp_setup_state+0x3d/0x90
    [ 2.858030] hyperv_init+0x14e/0x410
    [ 2.864689] ? enable_IR_x2apic+0x190/0x1a0
    [ 2.871349] apic_intr_mode_init+0x8b/0x100
    [ 2.878017] x86_late_time_init+0x20/0x30
    [ 2.884675] start_kernel+0x459/0x4fb
    [ 2.891329] secondary_startup_64_no_verify+0xb0/0xbb

Since the hypervisor already provides the VP assist pages for root
partition, we need to memremap the memory from hypervisor for root
kernel to use. The mapping is done in hv_cpu_init during bringup and is
unmapped in hv_cpu_die during teardown.

Signed-off-by: Praveen Kumar <kumarpraveen@linux.microsoft.com>
Reviewed-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Link: https://lore.kernel.org/r/20210731120519.17154-1-kumarpraveen@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-08-04 11:56:53 +00:00
Nick Richardson
c2eecaa193 pktgen: Remove redundant clone_skb override
When the netif_receive xmit_mode is set, a line is supposed to set
clone_skb to a default 0 value. This line is made redundant due to a
preceding line that checks if clone_skb is more than zero and returns
-ENOTSUPP.

Overriding clone_skb to 0 does not make any difference to the behavior
because if it was positive we return error. So it can be either 0 or
negative, and in both cases the behavior is the same.

Remove redundant line that sets clone_skb to zero.

Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:54:09 +01:00
Jonathan Lemon
773bda9649 ptp: ocp: Expose various resources on the timecard.
The OpenCompute timecard driver has additional functionality besides
a clock.  Make the following resources available:

 - The external timestamp channels (ts0/ts1)
 - devlink support for flashing and health reporting
 - GPS and MAC serial ports
 - board serial number (obtained from i2c device)

Also add watchdog functionality for when GNSS goes into holdover.

The resources are collected under a timecard class directory:

  [jlemon@timecard ~]$ ls -g /sys/class/timecard/ocp1/
  total 0
  -r--r--r--. 1 root 4096 Aug  3 19:49 available_clock_sources
  -rw-r--r--. 1 root 4096 Aug  3 19:49 clock_source
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 device -> ../../../0000:04:00.0/
  -r--r--r--. 1 root 4096 Aug  3 19:49 gps_sync
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 i2c -> ../../xiic-i2c.1024/i2c-2/
  drwxr-xr-x. 2 root    0 Aug  3 19:49 power/
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 pps ->
  ../../../../../virtual/pps/pps1/
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 ptp -> ../../ptp/ptp2/
  -r--r--r--. 1 root 4096 Aug  3 19:49 serialnum
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 subsystem ->
  ../../../../../../class/timecard/
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 ttyGPS -> ../../tty/ttyS7/
  lrwxrwxrwx. 1 root    0 Aug  3 19:49 ttyMAC -> ../../tty/ttyS8/
  -rw-r--r--. 1 root 4096 Aug  3 19:39 uevent

The labeling is needed at the minimum, in order to tell the serial
devices apart.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:52:50 +01:00
Pavel Tikhomirov
04190bf894 sock: allow reading and changing sk_userlocks with setsockopt
SOCK_SNDBUF_LOCK and SOCK_RCVBUF_LOCK flags disable automatic socket
buffers adjustment done by kernel (see tcp_fixup_rcvbuf() and
tcp_sndbuf_expand()). If we've just created a new socket this adjustment
is enabled on it, but if one changes the socket buffer size by
setsockopt(SO_{SND,RCV}BUF*) it becomes disabled.

CRIU needs to call setsockopt(SO_{SND,RCV}BUF*) on each socket on
restore as it first needs to increase buffer sizes for packet queues
restore and second it needs to restore back original buffer sizes. So
after CRIU restore all sockets become non-auto-adjustable, which can
decrease network performance of restored applications significantly.

CRIU need to be able to restore sockets with enabled/disabled adjustment
to the same state it was before dump, so let's add special setsockopt
for it.

Let's also export SOCK_SNDBUF_LOCK and SOCK_RCVBUF_LOCK flags to uAPI so
that using these interface one can reenable automatic socket buffer
adjustment on their sockets.

Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:52:03 +01:00
Ivan T. Ivanov
6b67d4d63e net: usb: lan78xx: don't modify phy_device state concurrently
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.

[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)

Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:51:14 +01:00
Jakub Kicinski
396492b4c5 docs: networking: netdevsim rules
There are aspects of netdevsim which are commonly
misunderstood and pointed out in review. Cong
suggest we document them.

Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:43:27 +01:00
Peilin Ye
625af9f029 tc-testing: Add control-plane selftests for sch_mq
Recently we added multi-queue support to netdevsim in commit d4861fc6be
("netdevsim: Add multi-queue support"); add a few control-plane selftests
for sch_mq using this new feature.

Use nsPlugin.py to avoid network interface name collisions.

Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-04 12:42:27 +01:00