This covers the UP / SMP (with no hardware assist for atomic r-m-w) as
well as ARC700 LLOCK/SCOND insns based.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 has an in-core intc which provides 2 priorities (a.k.a.) "levels"
of interrupts (per IRQ) hencforth referred to as L1/L2 interrupts.
CPU flags register STATUS32 has Interrupt Enable bits per level (E1/E2)
to globally enable (or disable) all IRQs at a level. Hence the
implementation of arch_local_irq_{save,restore,enable,disable}( )
The STATUS32 reg can be r/w only using the AUX Interface of ARC, hence
the use of LR/SR instructions. Further, E1/E2 bits in there can only be
updated using the FLAG insn.
The intc supports 32 interrupts - and per IRQ enabling is controlled by
a bit in the AUX_IENABLE register, hence the implmentation of
arch_{,un}mask_irq( ) routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Arnd in his review pointed out that arch Kconfig organisation has several
deficiencies:
* Build time entries for things which can be runtime extracted from DT
(e.g. SDRAM size, core clk frequency..)
* Not multi-platform-image-build friendly (choice .. endchoice constructs)
* cpu variants support (750/770) is exclusive.
The first 2 have been fixed in subsequent patches.
Due to the nature of the 750 and 770, it is not possible to build for
both together, w/o special runtime glue code which would hurt
performance.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
struct compat_ucontext * is a 64-bit pointer, so we need to use a
compat_uptr_t instead to avoid declaring a structure incompatible with
what AArch32 userspace expects.
Cc: <stable@vger.kernel.org>
Reported-by: Edmund Grimley-Evans <Edmund.Grimley-Evans@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* acpi-lpss:
ACPI / platform: create LPSS clocks if Lynxpoint devices are found during scan
clk: x86: add support for Lynxpoint LPSS clocks
x86: add support for Intel Low Power Subsystem
ACPI / platform: fix comment about the platform device name
ACPI: add support for CSRT table
* acpica: (56 commits)
ACPICA: Update version to 20130117
ACPICA: Update predefined info table for _MLS method
ACPICA: Remove some extraneous newlines in ACPI_ERROR type calls
ACPICA: iASL/Disassembler: Add option to ignore NOOP opcodes/operators
ACPICA: AcpiGetSleepTypeData: Allow \_Sx to return either 1 or 2 integers
ACPICA: Update ACPICA copyrights to 2013
ACPICA: Update predefined info table
ACPICA: Cleanup table handler naming conflicts.
ACPICA: Source restructuring: split large files into 8 new files.
ACPICA: Cleanup PM_TIMER_FREQUENCY definition.
ACPICA: Cleanup ACPI_DEBUG_PRINT macros to fix potential build breakages.
ACPICA: Update version to 20121220.
ACPICA: Interpreter: Fix Store() when implicit conversion is not possible.
ACPICA: Resources: Split interrupt share/wake bits into two fields.
ACPICA: Resources: Support for ACPI 5 wake bit in ExtendedInterrupt descriptor.
ACPICA: Interpreter: Add warning if 64-bit constant appears in 32-bit table.
ACPICA: Update ACPICA initialization messages.
ACPICA: Namespace: Eliminate dot...dot output during initialization.
ACPICA: Resource manager: Add support for ACPI 5 wake bit in IRQ descriptor.
ACPICA: Fix possible memory leak in dispatcher error path.
...
When a HP ProLiant DL980 G7 Server boots a regular kernel,
there will be intermittent lost interrupts which could
result in a hang or (in extreme cases) data loss.
The reason is that this system only supports x2apic physical
mode, while the kernel boots with a logical-cluster default
setting.
This bug can be worked around by specifying the "x2apic_phys" or
"nox2apic" boot option, but we want to handle this system
without requiring manual workarounds.
The BIOS sets ACPI_FADT_APIC_PHYSICAL in FADT table.
As all apicids are smaller than 255, BIOS need to pass the
control to the OS with xapic mode, according to x2apic-spec,
chapter 2.9.
Current code handle x2apic when BIOS pass with xapic mode
enabled:
When user specifies x2apic_phys, or FADT indicates PHYSICAL:
1. During madt oem check, apic driver is set with xapic logical
or xapic phys driver at first.
2. enable_IR_x2apic() will enable x2apic_mode.
3. if user specifies x2apic_phys on the boot line, x2apic_phys_probe()
will install the correct x2apic phys driver and use x2apic phys mode.
Otherwise it will skip the driver will let x2apic_cluster_probe to
take over to install x2apic cluster driver (wrong one) even though FADT
indicates PHYSICAL, because x2apic_phys_probe does not check
FADT PHYSICAL.
Add checking x2apic_fadt_phys in x2apic_phys_probe() to fix the
problem.
Signed-off-by: Stoney Wang <song-bo.wang@hp.com>
[ updated the changelog and simplified the code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1360263182-16226-1-git-send-email-yinghai@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix the following compile warning in kvm_register_steal_time():
CC arch/x86/kernel/kvm.o
arch/x86/kernel/kvm.c: In function ‘kvm_register_steal_time’: arch/x86/kernel/kvm.c:302:3:
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘phys_addr_t’ [-Wformat]
Introduced via:
5dfd486c47 x86, kvm: Fix kvm's use of __pa() on percpu areas
d765653445 x86, mm: Create slow_virt_to_phys()
f3c4fbb68e x86, mm: Use new pagetable helpers in try_preserve_large_page()
4cbeb51b86 x86, mm: Pagetable level size/shift/mask helpers
a25b931684 x86, mm: Make DEBUG_VIRTUAL work earlier in boot
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: shuahkhan@gmail.com
Cc: avi@redhat.com
Cc: gleb@redhat.com
Cc: mst@redhat.com
Link: http://lkml.kernel.org/r/1360119442.8356.8.camel@lorien2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This field was needed to differentiate memory slots created by the new
API, KVM_SET_USER_MEMORY_REGION, from those by the old equivalent,
KVM_SET_MEMORY_REGION, whose support was dropped long before:
commit b74a07beed
KVM: Remove kernel-allocated memory regions
Although we also have private memory slots to which KVM allocates
memory with vm_mmap(), !user_alloc slots in other words, the slot id
should be enough for differentiating them.
Note: corresponding function parameters will be removed later.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Fix PowerPC/Cell build fallout from:
8bd75c77b7 sched/rt: Move rt specific bits into new header file
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Without Posted Interrupt, current code is broken. Just disable by
default until Posted Interrupt is ready.
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
There are two ways to express an interruption subclass:
- As a bitmask, as used in cr6.
- As a number, as used in the I/O interruption word.
Unfortunately, we have treated the I/O interruption word as if it
contained the bitmask as well, which went unnoticed so far as
- (not-yet-released) qemu made the same mistake, and
- Linux guest kernels don't check the isc value in the I/O interruption
word for subchannel interrupts.
Make sure that we treat the I/O interruption word correctly.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Enable AESS data in hwmod in order to be able to probe
audio driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add AESS memory bank data in hwmod in order to provide memory address
information to the driver.
This version also changes the AESS main clock to use a
non-CLKCTRL-based functional clock. These are being removed from the
clock data, since they should be handled by the IP block integration
code. Without this change, the kernel crashes during boot. Thanks to
Tony Lindgren for reporting this during a test merge.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
[paul@pwsan.com: updated to change the AESS main_clk]
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable the AESS auto-gating control bit during AESS hwmod setup. This
fixes the following boot warning on OMAP4:
omap_hwmod: aess: _wait_target_disable failed
Without this patch, the AESS IP block does not indicate to the PRCM
that it is idle after it is reset. This prevents some types of SoC
power management until something sets the auto-gating control bit.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
After setup/enable, some IP blocks need some additional setting to
indicate the PRCM that they are inactive until they are configured.
Some examples on OMAP4 include the AESS and FSUSB IP blocks.
To fix this cleanly, this patch adds another optional function
pointer, enable_preprogram, to the IP block's hwmod data. The function
that is pointed to is called by the hwmod code immediately after the
IP block is reset.
This version of the patch includes a patch description fix from Felipe.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
pm_idle() on openrisc was dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: linux@lists.openrisc.net
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Remove the SYMBOL_PREFIX Kconfig symbol as it's empty anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The kernel might be invoked through the reset vector, so to
preserve parameters passed to it, temp regs that are not
in the function parameter range needs to be used.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Add dtsi for imx6q and imx6dl with non-common blocks moved into there.
Major differences between imx6dl and imx6q:
* Dual vs. Quad cores
* single vs. dual IPU
* 128 vs. 256 KB OCRAM
* imx6q: ECSPI5, OpenVG (GC355), SATA
* imx6dl: I2C4, PXP, EPDC, LCDIF
* iomuxc/pads definition
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX6 Quad and i.MX6 DualLite is similar enough to share one dtsi
file, so rename imx6q.dtsi to imx6qdl.dtsi preparing for the addition
of imx6dl support.
Another member of i.MX6 series i.MX6 SoloLite is different enough
from the other two, so it will stand as a separate dtsi. That's why
we rename to imx6qdl.dtsi not imx6.dtsi.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For ANATOP LDOs, vddcpu, vddsoc and vddpu
have step time settings in the misc2 register, need
to add necessary step time info for these three LDOs,
then regulator driver can add necessary delay based on
these settings.
offset 0x170:
bit [24-25]: vddcpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove silicon version from SDMA firmware.
This makes it consistent with other i.MX SoCs firmware names.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MBa53 is a baseboard for the TQMA53 embedded module. This enables/adds only
supported devices, i.e. it is not feature complete, because of missing drivers
in mainline linux.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tqma53 is an embedded module that has some features on board (e.g. emmc),
but mostly just provides access to them on its interface.
Going along with the imx53.dtsi, the tqma53.dtsi specifies the existing
devices and their pinctrl for this module. All devices that are not on the
module are disabled by default and need to be enabled in a baseboard DT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add pinctrl for cspi, csi.
Add new pingroups for can1 and uart3.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The keypad is on the accessory board of i.MX51 babbage
main board and is driven by Keypad Port(KPP) in SoC.
The keymap is the same to i.MX25 3stack platform as
the accessory board schematic tells that it is designed
in this way.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Just to keep consistency with other dts files, place 'status' entry as the last
one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi. Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing imx dtb targets, so that make dtbs can cover all imx dtbs.
It's pretty useful for testing dts changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add an entry for imx27-pdk.dtb, so that it can be generated by default.
Also, add an entry into Documentation/devicetree/bindings/arm/fsl.txt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx27-pdk is the name found on Freescale website, so use it instead of 3ds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Any devices wishing to use the AB8500's GPIO IRQs were forced to
request virtual IRQs from the gpio-ab8500 driver. Now that
responsibility has been passed back to the AB8500 core driver,
devices can request real IRQ numbers instead. This patch removes
any traces of the old virtual IRQ conversion handlers, which will
force any drivers requesting IRQs to use real IRQS.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AB8500 GPIO no longer handles its GPIO IRQs. Instead, the AB8500
core driver has taken back the responsibility. Prior to this
happening, the AB8500 GPIO driver provided a set of virtual IRQs
which were used as a pass-through. These virtual IRQs had a base
of MOP500_AB8500_VIR_GPIO_IRQ_BASE, which was passed though pdata.
We don't need to do this anymore, so we're pulling out the
property from the structure.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove 32-bit x86 a cmdline param "no-hlt",
and the cpuinfo_x86.hlt_works_ok that it sets.
If a user wants to avoid HLT, then "idle=poll"
is much more useful, as it avoids invocation of HLT
in idle, while "no-hlt" failed to do so.
Indeed, hlt_works_ok was consulted in only 3 places.
First, in /proc/cpuinfo where "hlt_bug yes"
would be printed if and only if the user booted
the system with "no-hlt" -- as there was no other code
to set that flag.
Second, check_hlt() would not invoke halt() if "no-hlt"
were on the cmdline.
Third, it was consulted in stop_this_cpu(), which is invoked
by native_machine_halt()/reboot_interrupt()/smp_stop_nmi_callback() --
all cases where the machine is being shutdown/reset.
The flag was not consulted in the more frequently invoked
play_dead()/hlt_play_dead() used in processor offline and suspend.
Since Linux-3.0 there has been a run-time notice upon "no-hlt" invocations
indicating that it would be removed in 2012.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org