IB flow tables need the underlay qp to perform flow steering.
Here we change the API of the flow tables creation to accept the
underlay QP number as a parameter in order to support IB (IPoIB) flow
steering.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New capability bit: ipoib_enhanced_offloads, indicates new ability for UD
QP to do RSS and enhanced IPoIB offloads and acceleration.
Add underlay_qpn to the TIS and flow_table objects In order to support
SET_ROOT command, to connect between IPoIB QPs and flow steering tables.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Azure hosts are not supporting non-TCP port numbers in vRSS hashing for
now. For example, UDP packet loss rate will be high if port numbers are
also included in vRSS hash.
So, we created this patch to use only IP numbers for hashing in non-TCP
traffic.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the outgoing skb has a RX queue mapping available, we use the queue
number directly, other than put it through Send Indirection Table.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of rx queues is determined by the rss_cpus parameter
or the cpu topology. If that is higher than EFX_MAX_RX_QUEUES the
driver can corrupt state.
Fixes: 8ceee660aa ("New driver "sfc" for Solarstorm SFC4000 controller.")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t_hash_start() does not increment *pos, where as t_next() must. But when
t_next() does increment *pos, it must still pass in the original *pos to
t_hash_start() otherwise it will skip the first instance:
# cd /sys/kernel/debug/tracing
# echo schedule:traceoff > set_ftrace_filter
# echo do_IRQ:traceoff > set_ftrace_filter
# echo call_rcu > set_ftrace_filter
# cat set_ftrace_filter
call_rcu
schedule:traceoff:unlimited
do_IRQ:traceoff:unlimited
The above called t_hash_start() from t_start() as there was only one
function (call_rcu), but if we add another function:
# echo xfrm_policy_destroy_rcu >> set_ftrace_filter
# cat set_ftrace_filter
call_rcu
xfrm_policy_destroy_rcu
do_IRQ:traceoff:unlimited
The "schedule:traceoff" disappears.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/media
Prior to this patch, there was 1 use of pr_warning and
310 uses of pr_warn in drivers/media
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
clang currently does not support these optimizations, only enable them
when they are available.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michael Davidson <md@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: grundler@chromium.org
Link: http://lkml.kernel.org/r/20170413172609.118122-1-mka@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As reported by James, Catalin and Mark, commit:
e69176d68d ("ef/libstub/arm/arm64: Randomize the base of the UEFI rt services region")
... results in a crash in the firmware, regardless of whether KASLR
is in effect or not and whether the firmware implements EFI_RNG_PROTOCOL
or not.
Mark has identified the root cause to be the inappropriate use of
TASK_SIZE in the stub, which arm64 defines as:
#define TASK_SIZE (test_thread_flag(TIF_32BIT) ? \
TASK_SIZE_32 : TASK_SIZE_64)
and testing thread flags at this point results in the dereference of
pointers in uninitialized structures.
So instead, introduce a preprocessor symbol EFI_RT_VIRTUAL_LIMIT and
define it to TASK_SIZE_64 on arm64 and TASK_SIZE on ARM, both of which
are compile time constants. Also, change the 'headroom' variable to
static const to force an error if this might change in the future.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170417093201.10181-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull clockevents updates from Daniel Lezcano
- Provide a framework to handle errata gracefuly for arm_arch_timer (Mark
Zyngier)
- Clarify the DT properties for the rockchip timer and add the clocksource as
an alternative to the bogus architected timer (Alexander Kochetkov)
- Rename the Gemini timer to Faraday timer fttmr010 and provide a specific
initialization for Gemini (Linus Walleij)
- Add missing newlines in the error message in the timers (Rafał Miłecki)
- Read the clock once and implement the delay timer on Orion (Russell King)
The /proc/bus/usb devices don't exist anymore, since when we
got rid of usbfs. Those devices are now seen at
/dev/bus/usb.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
gcc-4.4.3 fails to statically initialize members of a anon union.
See: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
The storage saving is not really worth it and aside of that it will catch
usage of the cache member for bandwidth and vice versa easier.
Fixes: 05b93417ce ("x86/intel_rdt/mba: Add primary support for Memory Bandwidth Allocation (MBA)")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CPUCLOCK_PID(which_clock) is a pid value from userspace so compare it
against task_pid_vnr, not current->pid. As task_pid_vnr is in the tasks
pid value in the tasks pid namespace, and current->pid is in the
initial pid namespace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The function no longer does anything. The is only a single caller of
register_sysctl_root when semantically there should be two. Remove
this function so that if someone decides this functionality is needed
again it will be obvious all of the callers of setup_sysctl_set need
to be audited and modified appropriately.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
* if a local variable of type uint16_t is unaligned, your compiler is FUBAR
* the whole point of get_unaligned_... is to avoid memcpy + ..._to_cpu().
Using it *after* memcpy() (into aligned object, no less) is pointless.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By default the i2c-core will try to get an irq with index 0 on ACPI / of
instantiated devices. This is troublesome on some ACPI systems where the
irq info at index 0 in the CRS table may contain nonsense and/or point
to an irqchip for which there is no Linux driver.
If this happens then before this commit the driver's probe method would
never get called because i2c_device_probe will try to get an irq by
calling acpi_dev_gpio_irq_get which will always return -EPROBE in this
case, as it waits for a matching irqchip driver to load. Thus causing
the driver to not get a chance to bind.
This commit adds a new disable_i2c_core_irq_mapping flag to struct
i2c_driver which a driver can set to tell the core to skip irq mapping.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
By default the i2c subsys creates an i2c-client for the first I2cSerialBus
resource of an acpi_device, but some acpi_devices have multiple
I2cSerialBus resources and we may want to instantiate i2c-clients for
the others.
This commit adds a new i2c_acpi_new_device function which can be used to
create an i2c-client for any I2cSerialBus resource of an acpi_device.
Note that the other resources may even be on a different i2c bus, so just
retrieving the client address is not enough.
Here is an example DSDT excerpt from such a device:
Device (WIDR)
{
Name (_HID, "INT33FE" /* XPOWER Battery Device */)
Name (_CID, "INT33FE" /* XPOWER Battery Device */)
Name (_DDN, "WC PMIC Battery Device")
<snip>
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x005E, ControllerInitiated, 0x000186A0,
AddressingMode7Bit, "\\_SB.PCI0.I2C7",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0036, ControllerInitiated, 0x000186A0,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0022, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0054, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0012
}
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0005
}
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
})
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Return (RBUF) /* \_SB_.PCI0.I2C7.WIDR.RBUF */
}
<snip>
}
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Modify struct i2c_acpi_lookup and i2c_acpi_fill_info() to allow
using them to get the info from a certain index in the ACPI-resource
list rather then taking the first I2cSerialBus resource.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Description of the problem:
- i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM";
- the fist HID (SMBUS01) is clearly defined in "SMBus Control Method
Interface Specification, version 1.0": "Each device must specify
'SMBUS01' as its _HID and use a unique _UID value";
- unfortunately, BIOS vendors (like AMI) seem to ignore this requirement
and implement "SMB0001" HID instead of "SMBUS01";
- I speculate that they do this because only "SMB0001" is hard coded in
Windows SMBus driver produced by Microsoft.
This leads to following situation:
- SMBus works out of box in Windows but not in Linux;
- board vendors are forced to add correct "SMBUS01" HID to BIOS to make
SMBus work in Linux. Moreover the same board vendors complain that
tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier
and produce errors. So they need to constantly patch the compiler for
each new version of BIOS.
As it is very unlikely that BIOS vendors implement a correct HID in
future, I would propose to consider whether it is possible to work around
the problem by adding MS HID to the Linux i2c-scmi driver.
v2: move the definition of the new HID to the driver itself.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Signed-off-by: Michael Brunner <Michael.Brunner@kontron.com>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Again, a batch that's been sitting a couple of weeks, mostly because I
anticipated a bit more material but it didn't show up -- which is good.
These are all your garden variety fixes for ARM platforms. Most visible issue
fixed here is probably the SMP reset issue on OMAP, the rest are minor stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJY877PAAoJEIwa5zzehBx3TaUQAKtE8CSmvdWIk5grVb4MBDfF
rXQ2R7WJF17LtVhIGwz9BPCQXMK+/XcSuXZ8bvUIoMsmOFXutDao7m7COD0z4aNo
CPWk7ceQRzIWvsmturla6aYGmpAbWzdDgQj61LnaFbQrzmJOHVvcJN685+L5NGkZ
8GBrzNmrvVkWz5N+msnrZRIcKpSqGCXrkjUU1EfHgUgNNdTf6BQRQSzVEYBtILEb
9bC3WdS1fosmSdbsBjcxHsAtWMyO64KqhA691+gGTR93wyOuCRgqv+/ucoFB1oi+
yjuhUVHW7Y5/8KOi67+97PwoKpZYpUFHge1/5iPbgEN6SqhOLzPAALGCKT4ONEQz
KmLl//kX1IJZTD/87OegSLDbpS7h2sRYS7FpwgAa1kyYYOHdsZsECzKfhEvgZNHX
Gtl2XLmtELM9quKQ2X8xWvjU5grfSLkng9OhDJ6ZCFhGddvjtHegq8J5diFyq281
qf4n/Gp/OLC9IoPUyZefn5ya77K8UZPNppqtiWTBbT1IuXWbPUVPKmZoCpq3Qwu+
2fdcFa3sIfpzDg9vkTszFAUCFkRqH5Jzy8BfNIQtfSq+pxwyIRWh88a5CV2RvYFB
uHSt5B88YR2PwoyhV2oFpYNkx3vVu9g+A35ClzIRTLhSMi+Ngh2+DcppHY+LficP
m9Hes98dZOv92JgiSaoQ
=C+Hz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Pull block fixes from Jens Axboe:
"Four small fixes.
Three of them fix the same error in NVMe, in loop, fc, and rdma
respectively. The last fix from Ming fixes a regression in this
series, where our bvec gap logic was wrong and causes an oops on
NVMe for certain conditions"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bio_will_gap() for first bvec with offset
nvme-fc: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-rdma: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-loop: Fix sqsize wrong assignment based on ctrl MQES capability
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
-----BEGIN PGP SIGNATURE-----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=07Xj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull cgroup fix from Tejun Heo:
"Unfortunately, the commit to fix the cgroup mount race in the previous
pull request can lead to hangs.
The original bug has been around for a while and isn't too likely to
be triggered in usual use cases. Revert the commit for now"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Revert "cgroup: avoid attaching a cgroup root to two different superblocks"
Here is a single tty core revert for a patch that was reported to cause
problems. The original issue is one that we have lived with for
decades, so trying to scramble to fix the fix in time for 4.11-final
does not make sense due to the fragility of the tty ldisc layer. Just
reverting it makes sense for now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWPMjIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl+ywCfbEc9XQ2+eDebFSs673OaDUxApmIAoMe+4Qj5
puBC7ThZvCwrwACsoBWd
=rugQ
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fix from Greg KH:
"Here is a single tty core revert for a patch that was reported to
cause problems.
The original issue is one that we have lived with for decades, so
trying to scramble to fix the fix in time for 4.11-final does not make
sense due to the fragility of the tty ldisc layer. Just reverting it
makes sense for now"
* tag 'tty-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: don't panic on OOM in tty_set_ldisc()"
bug. This bug has been there sinc function tracing was added way back
when. But my new development depends on this bug being fixed, and it
should be fixed regardless as it causes ftrace to disable itself when
triggered, and a reboot is required to enable it again.
The bug is that the function probe does not disable itself properly
if there's another probe of its type still enabled. For example:
# cd /sys/kernel/debug/tracing
# echo schedule:traceoff > set_ftrace_filter
# echo do_IRQ:traceoff > set_ftrace_filter
# echo \!do_IRQ:traceoff > /debug/tracing/set_ftrace_filter
# echo do_IRQ:traceoff > set_ftrace_filter
The above registers two traceoff probes (one for schedule and one for
do_IRQ, and then removes do_IRQ. But since there still exists one for
schedule, it is not done properly. When adding do_IRQ back, the breakage
in the accounting is noticed by the ftrace self tests, and it causes
a warning and disables ftrace.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJY8ovvFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
nkAH/jfsXUWIbZ6J0A7+nmGiBdIVwLwG0ZOJClcxjnCSpsNs+FO/0w6ragtIYCi2
Km+0s/slA5GOddG4Miga/dhtxGhDosyXnxqC+4GmD0maqJGLweJLbmiQ1xhra0hr
XGDI+SXHM/n22zVkFEbkGXgxMvOHeR+X/sREZo3XmoXRLbc1QVtTEe/8TdlLXwE5
5Fs07xSQqx4TS7oBxIjipHnbHL/gIktEo0HiEmq73++r42MztIMYZPoV+cXuim37
C6xO4PxfPN0aRh9W5gdiMnbv6lummVBNQXwpMya0vTbxz/9WeUex8c+lcInQUJgA
FhQWKaCGyi0UK4Pa2Pz/Dmxuti0=
=LYLo
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.11-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"While rewriting the function probe code, I stumbled over a long
standing bug. This bug has been there sinc function tracing was added
way back when. But my new development depends on this bug being fixed,
and it should be fixed regardless as it causes ftrace to disable
itself when triggered, and a reboot is required to enable it again.
The bug is that the function probe does not disable itself properly if
there's another probe of its type still enabled. For example:
# cd /sys/kernel/debug/tracing
# echo schedule:traceoff > set_ftrace_filter
# echo do_IRQ:traceoff > set_ftrace_filter
# echo \!do_IRQ:traceoff > /debug/tracing/set_ftrace_filter
# echo do_IRQ:traceoff > set_ftrace_filter
The above registers two traceoff probes (one for schedule and one for
do_IRQ, and then removes do_IRQ.
But since there still exists one for schedule, it is not done
properly. When adding do_IRQ back, the breakage in the accounting is
noticed by the ftrace self tests, and it causes a warning and disables
ftrace"
* tag 'trace-v4.11-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix removing of second function probe
All required stateless 4-byte op codes are supported by this flash
chip. The stateless 4-byte support can't be autodetected due to a
missing 4-byte Address Instruction Table in SFDP.
Fixes hangs on reboot for SoCs expecting the flash chip in 3byte mode.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There were a bunch of places in pblk_lines_init() where we didn't set an
error code. And in pblk_writer_init() we accidentally return 1 instead
of a correct error code, which would result in a Oops later.
Fixes: 11a5d6fdf919 ("lightnvm: physical block device (pblk) target")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
WARN_ON() takes a condition, not an error message. I slightly tweaked
some conditions so hopefully it's more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These labels are reversed so we could end up dereferencing an error
pointer or leaking.
Fixes: 7f347ba6bb3a ("lightnvm: physical block device (pblk) target")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Convert sprintf calls to strlcpy in order to make possible buffer
overflow more obvious.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Prefix the nvm_free static function with a missing static keyword.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Target initialization has two responsibilities: creating the target
partition and instantiating the target. This patch enables to create a
factory partition (e.g., do not trigger recovery on the given target).
This is useful for target development and for being able to restore the
device state at any moment in time without requiring a full-device
erase.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The NVMe I/O command control bits are 16 bytes, but is interpreted as
32 bytes in the lightnvm user I/O data path.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Reorder disk allocation such that the disk structure can be put
safely.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The dev->lun_map bits are cleared twice if an target init error occurs.
First in the target clean routine, and then next in the nvm_tgt_create
error function. Make sure that it is only cleared once by extending
nvm_remove_tgt_devi() with a clear bit, such that clearing of bits can
ignored when cleaning up a successful initialized target.
Signed-off-by: Javier González <javier@cnexlabs.com>
Fix style.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
mempool_alloc() cannot fail if the gfp flags allow it to
sleep, and both GFP_KERNEL and GFP_NOIO allows for sleeping.
So rrpc_move_valid_pages() and rrpc_make_rq() don't need to
test the return value.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The asserts in _nvme_nvm_check_size are not compiled due to the function
not begin called. Make sure that it is called, and also fix the wrong
sizes of asserts for nvme_nvm_addr_format, and nvme_nvm_bb_tbl, which
checked for number of bits instead of bytes.
Reported-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>