Use a single no_mem_stripes list instead of per member device lists for
handling stripes that need retrying in case of failed io_unit
allocation. Because io_units are allocated from a memory pool shared
between all member disks, the no_mem_stripes list should be checked when
an io_unit for any member is freed. This fixes a deadlock that could
happen if there are stripes in more than one no_mem_stripes list.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
There are many codecs with the capability of jack detection. Usually,
we create a jack on machine driver but there is no common function for
machine driver to deliver the jack pointer to codec driver.
snd_soc_codec_set_jack can be used for delivering the jack pointer to
codec driver and enable the jack detection function. To make it work,
codec driver need to define a callback function to receive the jack
pointer and do all necessary procedure for enabling jack detection.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for hi6210 i2s controller found on hi6220 boards.
Signed-off-by: Andy Green <andy.green@linaro.org>
[jstultz: Forward ported to mainline, fairly major rework
based on suggestions from Mark Brown]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds DT bindings documentation for the hi6210-i2s driver.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are certain parts of the kernel that cannot let stack tracing
proceed (namely in RCU), because the stack tracer uses RCU, and parts of RCU
internals cannot handle having RCU read side locks taken.
Add stack_tracer_disable() and stack_tracer_enable() functions to let RCU
stop stack tracing on the current CPU when it is in those critical sections.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The updates to the trace_active per cpu variable can be updated with the
__this_cpu_*() functions as it only gets updated on the CPU that the variable
is on.
Thanks to Paul McKenney for suggesting __this_cpu_* instead of this_cpu_*.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Nordic Semiconductor is a semiconductor company specializing in ARM
Cortex-M based SoCs for low-power wireless communication, especially
Bluetooth.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
fix_sync_read_error() modifies a bio on a newly faulty
device by setting bi_end_io to end_sync_write.
This ensure that put_buf() will still call rdev_dec_pending()
as required, but makes sure that subsequent code in
fix_sync_read_error() doesn't try to read from the device.
Unfortunately this interacts badly with sync_request_write()
which assumes that any bio with bi_end_io set to non-NULL
other than end_sync_read is safe to write to.
As the device is now faulty it doesn't make sense to write.
As the bio was recently used for a read, it is "dirty"
and not suitable for immediate submission.
In particular, ->bi_next might be non-NULL, which will cause
generic_make_request() to complain.
Break this interaction by refusing to write to devices
which are marked as Faulty.
Reported-and-tested-by: Michael Wang <yun.wang@profitbricks.com>
Fixes: 2e52d449bc ("md/raid1: add failfast handling for reads.")
Cc: stable@vger.kernel.org (v4.10+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The XV601/709 encodings are special: they signal limited range, but use the full range
to encode a larger gamut with R', G' and B' values outside the [0-1] range.
So don't clamp to limited range for these two encodings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The XV601/709 Y'CbCr encoding was changed to limited range, but the comment
still indicates full range.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
md.c: it needs to release the mddev lock before
the array_size_store() returns.
Fixes: ab5a98b132 ("md-cluster: change array_sectors and update size are not supported")
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Reviewed-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Code can be simplified by using the standard tolower() funtion.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment for the FSLSSI_I2S_RATES definition states that the
driver currently only supports I2S slave mode, which is no longer
correct.
As FSLSSI_I2S_RATES is the same as the standard SNDRV_PCM_RATE_CONTINUOUS,
just remove its definition and its comments to make the code simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
if called md_set_readonly and set MD_CLOSING bit, the mddev cannot
be opened any more due to the MD_CLOING bit wasn't cleared. Thus it
needs to be cleared in md_ioctl after any call to md_set_readonly()
or do_md_stop().
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: af8d8e6f03 ("md: changes for MD_STILL_CLOSED flag")
Cc: stable@vger.kernel.org (v4.9+)
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some of the macros didn't use the parenthesis around the parameters when
used in the body of the macro.
Signed-off-by: Nikola Jelic <nikola.jelic83@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If DMA does not support INTERLEAVE, deinterlace_probe() breaks off
initialization, releases dma channel, but returns zero.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
TRY_FMT already disables the YUYV format if the VDOA is not available.
ENUM_FMT must do the same.
Fixes: d40e98c13b ("[media] coda: support YUYV output if VDOA is used")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.
Fixes: 4f57d27be2 ("[media] tvp5150: fix tvp5150_fill_fmt()")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 1abf71e moved the creation of new_smi->dev to earlier in the init
sequence in order to provide infrastructure for log printing.
However, the init_name was created with a hard-coded value of zero. This
presents a problem in systems with more than one interface, producing a
call trace in dmesg.
To correct the problem, simply use smi_num instead of the hard-coded
value of zero.
Tested on a lenovo x3950.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
There was actually a more general problem, the platform device wasn't
being set correctly, either, and there was a possible (though extremely
unlikely) race on smi_num. Add locks to clean up the race and use the
proper value for the platform device, too.
Tested on qemu in various configurations.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We need to set "first = 0' at the end of rdev_for_each
loop, so we can get the array's min_offset_diff correctly
otherwise min_offset_diff just means the last rdev's
offset diff.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e7 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.
Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When recoverying a single missing/failed device in a RAID6,
those stripes where the Q block is on the missing device are
handled a bit differently. In these cases it is easy to
check that the P block is correct, so we do. This results
in the P block be destroy. Consequently the P block needs
to be read a second time in order to compute Q. This causes
lots of seeks and hurts performance.
It shouldn't be necessary to re-read P as it can be computed
from the DATA. But we only compute blocks on missing
devices, since c337869d95 ("md: do not compute parity
unless it is on a failed drive").
So relax the change made in that commit to allow computing
of the P block in a RAID6 which it is the only missing that
block.
This makes RAID6 recovery run much faster as the disk just
"before" the recovering device is no longer seeking
back-and-forth.
Reported-by-tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MC support is needed by the em28xx driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The resource control filesystem provides only a bitmask based cpus file for
assigning CPUs to a resource group. That's cumbersome with large cpumasks
and non-intuitive when modifying the file from the command line.
Range based cpu lists are commonly used along with bitmask based cpu files
in various subsystems throughout the kernel.
Add 'cpus_list' file which is CPU range based.
# cd /sys/fs/resctrl/
# echo 1-10 > krava/cpus_list
# cat krava/cpus_list
1-10
# cat krava/cpus
0007fe
# cat cpus
fffff9
# cat cpus_list
0,3-23
[ tglx: Massaged changelog and replaced "bitmask lists" by "CPU ranges" ]
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Shaohua Li <shli@fb.com>
Link: http://lkml.kernel.org/r/20170410145232.GF25354@krava
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc is inconsistently formatted. Fix it up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
The vsyscall32 sysctl can racy against a concurrent fork when it switches
from disabled to enabled:
arch_setup_additional_pages()
if (vdso32_enabled)
--> No mapping
sysctl.vsysscall32()
--> vdso32_enabled = true
create_elf_tables()
ARCH_DLINFO_IA32
if (vdso32_enabled) {
--> Add VDSO entry with NULL pointer
Make ARCH_DLINFO_IA32 check whether the VDSO mapping has been set up for
the newly forked process or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170410151723.602367196@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vdso_enabled can be set to arbitrary integer values via the kernel command
line 'vdso32=' parameter or via 'sysctl abi.vsyscall32'.
load_vdso32() only maps VDSO if vdso_enabled == 1, but ARCH_DLINFO_IA32
merily checks for vdso_enabled != 0. As a consequence the AT_SYSINFO_EHDR
auxiliary vector for the VDSO_ENTRY is emitted with a NULL pointer which
causes a segfault when the application tries to use the VDSO.
Restrict the valid arguments on the command line and the sysctl to 0 and 1.
Fixes: b0b49f2673 ("x86, vdso: Remove compat vdso support")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Roland McGrath <roland@redhat.com>
Link: http://lkml.kernel.org/r/1491424561-7187-1-git-send-email-minipli@googlemail.com
Link: http://lkml.kernel.org/r/20170410151723.518412863@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ISL9305_MAX_REGULATOR is the last index used to access the init_data[]
array, so we need to add one to this last index to obtain the necessary
array size.
This fixes the following smatch error:
drivers/regulator/isl9305.c:160 isl9305_i2c_probe() error: buffer overflow 'pdata->init_data' 3 <= 3
Fixes: dec38b5ce6 ("regulator: isl9305: Add Intersil ISL9305/H driver")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output voltage of a voltage controlled regulator can be controlled
through the voltage of another regulator. The current version of this
driver assumes that the output voltage is a linear function of the control
voltage.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to have MFD_CPCAP and CPCAP_REGULATOR as built-in to
be able to mount root on the eMMC. And then POWER_RESET_GPIO
is good to have built-in. The rest of the devices can be loadable
modules.
This gets various devices such as regulators, touchscreen, power
button, HDMI audio, LEDs, RTC, and ADC working.
Note that omapdrm needs to be configured manually as we're still
using omapfb by default.
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.
Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.
This causes a "NULL pointer dereference" error.
Fixes: f51e80804f ("[media] cec: pass parent device in register(), not allocate()")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>