Add HWMOD_CLKDM_NOAUTO flag to DCAN1 module.
Without this DCAN1 module remains stuck in transition
after the CAN interface is brought down. This is also suggested
in Errata i893 "DCAN Initialization Sequence".
Add the HWMOD_CLKDM_NOAUTO to DCAN2 module as well
as it is mentioned in Errata i893.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compile-tested only (by hacking it to compile on x86).
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Those two new SCM calls are needed from qcom-iommu driver in order
to initialize secure iommu page table.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the RPM Clock Controller DT node for msm8974-based platforms, so that
drivers can use the clocks provided by the RPM processor.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The DTS referred to SDC5 when it meant SDC1.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
To make the picture complete, add DTS entries also for the
second and fourth MMC/SD blocks on the MSM8660. SDC2 is
an 8-bit interface and SDC4 is a 4-bit interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Without this patch (and with CONFIG_QCOM_ADSP_PIL), I get this error:
[ 0.711529] qcom_adsp_pil adsp-pil: failed to get xo clock
[ 0.711540] remoteproc remoteproc0: releasing adsp-pil
With this patch, adsp-pil can initialize correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial set of CoreSight components found on Qualcomm
msm8974 and apq8074 based platforms, including the APQ8074
Dragonboard board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
It's necessary to reference the xo clock and cx supply, so specify these
in the node. Also move the Hexagon smd-edge into the hexagon node, to
enable SSR.
As cxo is not yet available we reference the fixed version of cxo for
now, which will work until proper power management is implemented.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The PMU on msm8916 is for the cortex-a53 type CPU. Update the
compatible to the more specific one so we can get the a53
specific events out of the PMU.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The SMEM state property name changes between the integration branch and
mainline, update to use the correct one.
Fixes: 2f45d9fcd5 ("arm64: dts: msm8996: Add SMP2P and APCS nodes")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Rock 2 square board has a USB -> SATA converter hooked up to its usb
host1 connection. Enable the usb controller and always turn on the power
on the 5V sata power connector (controlled by gpio).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-----BEGIN PGP SIGNATURE-----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=G9qe
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-leds-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into for-next
Immutable branch between MFD and LEDS due for the v4.12 merge window
* tag 'ib-mfd-leds-v4.12':
mfd: cpcap: Add missing include dependencies
For some platforms, for example Broadwell, it doesn't support cycles
for LBR. But the perf always prints cycles:0, it's not necessary.
The patch refactors the LBR info print code and drops the cycles:0.
For example: perf report --branch-history --no-children --stdio
On Broadwell:
--0.91%--__random_r random_r.c:394 (iterations:2)
__random_r random_r.c:360 (predicted:0.0%)
__random_r random_r.c:380 (predicted:0.0%)
__random_r random_r.c:357
On Skylake:
--1.07%--main div.c:39 (predicted:52.4% cycles:1 iterations:17)
main div.c:44 (predicted:52.4% cycles:1)
main div.c:42 (cycles:2)
compute_flag div.c:28 (cycles:2)
compute_flag div.c:27 (cycles:1)
rand rand.c:28 (cycles:1)
rand rand.c:28 (cycles:1)
__random random.c:298 (cycles:1)
__random random.c:297 (cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (cycles:1)
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Link: http://lkml.kernel.org/r/1489046786-10061-1-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fixes to multiple issues in virtio. Most notably
a regression fix for crashes reported by Fedora users.
Hybernate is still reportedly broken, working on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY2qEcAAoJECgfDbjSjVRpM/oH/3GPZOh9/tMzDFDaDljqtWQy
PGVb74/3+O55xOOq9nyyS3+6BlCXmiUcynxg61QUOUqUuHPPdH/OntyyPgG0pYkx
271W81C1yc2xFp/qkOiMWKiPmsbJ7ykVg37NWtxm7Phf4RgX3wgymq87hWr4Td1G
q9k6oyMCmvJUECJVxOVHjPt+oYQ7zQkFBNB8kSNlj67gbe533jkPt46MMlXbX7fQ
lPdJTnLXN/GQxnVtw5AAiWF87z0wNVUefrLe9sHW3KOeGBdne4NXblvz3WF/iPq4
N96thgm7QOP3NgAqbaUa7Fb0+jxyi2DNYFrVPxnf+nOOQy/AVUX6GRZJ2Tu6gF0=
=oSO5
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes to multiple issues in virtio.
Most notably a regression fix for crashes reported by Fedora users.
Hibernate is still reportedly broken, working on it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: prevent uninitialized variable use
virtio-balloon: use actual number of stats for stats queue buffers
virtio_balloon: init 1st buffer in stats vq
virtio_pci: fix out of bound access for msix_names
It is allowed by code to register mailbox controller that sets txdone_poll
flag to request timer-based polling with missed ->last_tx_done() method.
If such thing happens and since presence of last_tx_done() is not checked
it will fail in hrtimer callback function txdone_hrtimer() when first
message will be transmitted.
This patch adds check for this method and logging of error on
registration of mailbox controller if it requested timer-based polling.
Signed-off-by: Alexey Klimov <alexey.klimov@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch adds device tree bindings document for the FlexRM
ring manager found on Broadcom iProc SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some of the Broadcom iProc SoCs have FlexRM ring manager
which provides a ring-based programming interface to various
offload engines (e.g. RAID, Crypto, etc).
This patch adds a common mailbox driver for Broadcom FlexRM
ring manager which can be shared by various offload engine
drivers (implemented as mailbox clients).
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Pramod KUMAR <pramod.kumar@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Update the DT bindings documentation to reflect the new NSP version
of PDC driver compatibility string.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Adds support for Northstar Plus (NS+) products to the PDC mailbox
driver. The PDC driver was originally written to support the PDC
ring manager in the Northstar2 (64-bit) device. The NS+ (32 bit
device) uses an almost identical ring manager, though with a
different name. We just need to check for the type of hardware in
use, in order to write the appropriate interrupt configuration register.
Also updated DMA width to be correct for both NS+ and NS2.
Tested on NS+ and NS2.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Check for mbox_chan_ops structures that are only stored in the ops field
of a mbox_controller structure. This field is of type const struct
mbox_chan_ops *, so mbox_chan_ops structures having this property can be
declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
struct mbox_chan_ops i@p = {...};
@ok1@
identifier r1.i;
struct hi6220_mbox mbox;
struct slimpro_mbox ctx;
position p;
@@
(
mbox.controller.ops=&i@p
|
ctx.mb_ctrl.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct mbox_chan_ops i;
File size details:
text data bss dec hex filename
2310 248 0 2558 9fe drivers/mailbox/hi6220-mailbox.o
2366 192 0 2558 9fe drivers/mailbox/hi6220-mailbox.o
1500 248 0 1748 6d4 mailbox/mailbox-xgene-slimpro.o
1556 192 0 1748 6d4 mailbox/mailbox-xgene-slimpro.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The latest gcc-7.0.1 snapshot reports a new warning:
virtio/virtio_balloon.c: In function 'update_balloon_stats':
virtio/virtio_balloon.c:258:26: error: 'events[2]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:260:26: error: 'events[3]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:261:56: error: 'events[18]' is used uninitialized in this function [-Werror=uninitialized]
virtio/virtio_balloon.c:262:56: error: 'events[17]' is used uninitialized in this function [-Werror=uninitialized]
This seems absolutely right, so we should add an extra check to
prevent copying uninitialized stack data into the statistics.
>From all I can tell, this has been broken since the statistics code
was originally added in 2.6.34.
Fixes: 9564e138b1 ("virtio: Add memory statistics reporting to the balloon driver (V4)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio balloon driver contained a not-so-obvious invariant that
update_balloon_stats has to update exactly VIRTIO_BALLOON_S_NR counters
in order to send valid stats to the host. This commit fixes it by having
update_balloon_stats return the actual number of counters, and its
callers use it when pushing buffers to the stats virtqueue.
Note that it is still out of spec to change the number of counters
at run-time. "Driver MUST supply the same subset of statistics in all
buffers submitted to the statsq."
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When init_vqs runs, virtio_balloon.stats is either uninitialized or
contains stale values. The host updates its state with garbage data
because it has no way of knowing that this is just a marker buffer
used for signaling.
This patch updates the stats before pushing the initial buffer.
Alternative fixes:
* Push an empty buffer in init_vqs. Not easily done with the current
virtio implementation and violates the spec "Driver MUST supply the
same subset of statistics in all buffers submitted to the statsq".
* Push a buffer with invalid tags in init_vqs. Violates the same
spec clause, plus "invalid tag" is not really defined.
Note: the spec says:
When using the legacy interface, the device SHOULD ignore all values in
the first buffer in the statsq supplied by the driver after device
initialization. Note: Historically, drivers supplied an uninitialized
buffer in the first buffer.
Unfortunately QEMU does not seem to implement the recommendation
even for the legacy interface.
Cc: stable@vger.kernel.org
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fedora has received multiple reports of crashes when running
4.11 as a guest
https://bugzilla.redhat.com/show_bug.cgi?id=1430297https://bugzilla.redhat.com/show_bug.cgi?id=1434462https://bugzilla.kernel.org/show_bug.cgi?id=194911https://bugzilla.redhat.com/show_bug.cgi?id=1433899
The crashes are not always consistent but they are generally
some flavor of oops or GPF in virtio related code. Multiple people
have done bisections (Thank you Thorsten Leemhuis and
Richard W.M. Jones) and found this commit to be at fault
07ec51480b is the first bad commit
commit 07ec51480b
Author: Christoph Hellwig <hch@lst.de>
Date: Sun Feb 5 18:15:19 2017 +0100
virtio_pci: use shared interrupts for virtqueues
The issue seems to be an out of bounds access to the msix_names
array corrupting kernel memory.
Fixes: 07ec51480b ("virtio_pci: use shared interrupts for virtqueues")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Add reset lines for the Denali NAND controller on all UniPhier SoCs,
for the Cadence eMMC controller on LD11/LD20 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Moving enabling of function tracing to early boot, even before scheduling is
enabled, means that it is not safe to enable interrupts. When function
tracing was enabled at boot up, it use to happen after scheduling and the
other CPUs were brought up. That required running a sync across all CPUs
when modifying the function hook locations in the code. To do the
synchronization, interrupts had to be enabled. Now function tracing can be
started before the other CPUs are brought up, and enabling interrupts in
that case is dangerous. As only tho boot CPU is active, there is no reason
to run the synchronization. If the online CPU count is one, do not bother
doing the synchronization. This removes the need to enable interrupts.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This driver is now used only on platforms which support device tree, so
it is safe to remove legacy platform data based initialization code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For plat-samsung:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All three devices provide GPIO based LEDs named power,
wlan and app.
Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a typo, it should be GPIO176 and not GPIO106.
And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.
Fixes: 0d4cb3ccee ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch kills the warning reported on powerpc_pseries,
and actually we don't need the initialization.
After merging the md tree, today's linux-next build (powerpc
pseries_le_defconfig) produced this warning:
drivers/md/raid1.c: In function 'raid1d':
drivers/md/raid1.c:2172:9: warning: 'page_len$' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (memcmp(page_address(ppages[j]),
^
drivers/md/raid1.c:2160:7: note: 'page_len$' was declared here
int page_len[RESYNC_PAGES];
^
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Fix a filelayout GETDEVICEINFO call hang triggered from the LAYOUTGET
pnfs_layout_process where the GETDEVICEINFO call is waiting for a
session slot, and the LAYOUGET call is waiting for pnfs_layout_process
to complete before freeing the slot GETDEVICEINFO is waiting for..
This occurs in testing against the pynfs pNFS server where the
the on-wire reply highest_slotid and slot id are zero, and the
target high slot id is 8 (negotiated in CREATE_SESSION).
The internal fore channel slot table max_slotid, the maximum allowed
table slotid value, has been reduced via nfs41_set_max_slotid_locked
from 8 to 1. Thus there is one slot (slotid 0) available for use but
it has not been freed by LAYOUTGET proir to the GETDEVICEINFO request.
In order to ensure that layoutrecall callbacks are processed in the
correct order, nfs4_proc_layoutget processing needs to be finished
e.g. pnfs_layout_process) before giving up the slot that identifies
the layoutget (see referring_call_exists).
Move the filelayout_check_layout nfs4_find_get_device call outside of
the pnfs_layout_process call tree.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Properly implement emulation of the TLBR instruction for Trap & Emulate.
This instruction reads the TLB entry pointed at by the CP0_Index
register into the other TLB registers, which may have the side effect of
changing the current ASID. Therefore abstract the CP0_EntryHi and ASID
changing code into a common function in the process.
A comment indicated that Linux doesn't use TLBR, which is true during
normal use, however dumping of the TLB does use it (for example with the
relatively recent 'x' magic sysrq key), as does a wired TLB entries test
case in my KVM tests.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
SDT marker argument is in N@OP format. N is the size of argument and OP
is the actual assembly operand. OP is arch dependent component and hence
it's parsing logic also should be placed under tools/perf/arch/.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexis Berlemont <alexis.berlemont@gmail.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170328094754.3156-3-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
I found couple of events using al, bl, cl and dl registers for argument.
These are not directly accepted by uprobe_events and thus needs to be
mapped to ax, bx, cx and dx respectively.
Few ex,
/usr/bin/qemu-system-s390x
css_adapter_interrupt: 1@%bl
css_chpid_add: 1@%cl 1@%sil 1@%dl
dma_bdrv_io: 8@%rbx 8@%rbp -8@%r14 1@%al
/usr/bin/postgres
buffer__read__done: ... -1@-bash -1@%al
buffer__read__start: ... -1@%al
I don't find any sdt events using ah, bh,... registers. But I also don't
see any reason to not use them, so there might be rare events using
these registers, and if so, perf should have a renaming logic for them
too.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexis Berlemont <alexis.berlemont@gmail.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170328094754.3156-2-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In preparation for moving the filelayout getdeviceinfo call from
filelayout_alloc_lseg called by pnfs_process_layout
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Several major vendor USB-C->HDMI converters, in particular the DA200,
fail to recover a 5.4 GHz 1 lane signal if the link N is greater than
0x80000.
The link M and N depend on the pixel clock and link clock ratio. With
current code link N exceeds 0x80000 only when link clock >= 540000
kHz. Except for the eDP intermediate link clocks, at least the four
least significant bits are always zero. Just one bit shift right would
be enough to bring even the DP 1.4 810000 kHz link clock under 0x80000
link N. The pixel clock for modes that require a link clock >= 540000
kHz would also have several least significant bits zero. Unless the user
provides a mode with an odd pixel clock value, we can reduce the numbers
to reach the goal, with no loss in precision.
The DP spec even mentions sources making choices that "allow for static
and relatively small Mvid and Nvid values", thus reducing the link M/N
regardless of the sink in question seems justified.
Everything here is based on the work and information gathered by Clint
Taylor <clinton.a.taylor@intel.com>. This is just an iteration to reduce
the parameters regardless of lane count, link rate, or sink.
Reference: http://patchwork.freedesktop.org/patch/msgid/1490225256-11667-1-git-send-email-clinton.a.taylor@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93578
Tested-by: Mads <mads@ab3.no>
Tested-by: PJ <foobar@pjmodos.net>
Tested-by: François Guerraz <kubrick@fgv6.net>
Tested-by: Lev Popov <leo@nabam.net>
Tested-by: Igor Krivenko <igor.s.krivenko@gmail.com>
Tested-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490614405-23337-1-git-send-email-jani.nikula@intel.com
Add EE and AO domains pins for the spdif output to the gxl device tree.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>