Intel Gemini Lake is essentially Broxton with different PCI IDs. Add these
new PCI IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
The AXP806_REG_ADDR_EXT was previously configured by Allwinner's
bootloader. Work on U-boot SPL support now allows us to switch
to mainline U-boot, which doesn't do this for us. There might
be other bare minimum bootloaders out there which don't to this
either. It's best to handle this in the kernel.
This patch sets AXP806_REG_ADDR_EXT to 0x10, which is what we
know to be the proper value for a standard AXP806 in slave mode.
Afterwards it will reinitialize the regmap cache, to purge any
invalid stale values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Notify EC when going to or returning from suspend so that proper actions
related to wake events can be taken.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec driver is still active while the device is suspended.
Besides that, it also tries to transfer data even after the I2C host had
been suspended. This patch uses a simple flag to prevent this.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Aspeed SoC Display Controller is presented as a syscon device to
arbitrate access by display and pinmux drivers. Video pinmux
configuration on fifth generation SoCs depends on bits in both the
System Control Unit and the Display Controller.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LPC bus pinmux configuration on fifth generation Aspeed SoCs depends
on bits in both the System Control Unit and the LPC Host Controller.
The Aspeed LPC Host Controller is described as a child node of the
LPC host-range syscon device for arbitration of access by the host
controller and pinmux drivers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Whilst describing a device and not a bus, simple-mfd is modelled on
simple-bus where child nodes are iterated and registered as platform
devices. Some complex devices, e.g. the Aspeed LPC controller, can
benefit from address space mapping such that child nodes can use the
regs property to describe their resource offsets within the
multi-function device.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD_SUN4I_GPADC and TOUCHSCREEN_SUN4I are incompatible (both are drivers
for Allwinner SoCs' ADC). This makes sure TOUCHSCREEN_SUN4I isn't
enabled while MFD_SUN4I_GPADC is enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial fix to spelling mistake in MFD headers.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP223 shares most of its logic with the AXP221 but has some
differences for the VBUS power supply driver. Thus, to probe the driver
with the correct compatible, the AXP221 and the AXP223 now have separate
MFD cells.
AXP221 MFD cells are renamed from axp22x_cells to axp221_cells to avoid
confusion.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp288 pmic has a lot more volatile registers then we were
listing in axp288_volatile_ranges, fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add defines for the AXP288_POWER_REASON and AXP288_RT_BATT_V_H and
AXP288_RT_BATT_V_L and AXP288_BC_* registers. While at it also move the
AXP288_TS_ADC_H-AXP288_GP_ADC_L defines, which for some reason where
in a different place, together with the rest of the AXP288 specific
defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The adc-enable register for the axp288 is 0x82, not 0x84.
0x82 is already defined as AXP20X_ADC_EN1 and that is what the
axp288_adc driver is actually using, so simply drop the wrong
AXP288_PMIC_ADC_EN define.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The R in PEK_DBR stands for rising, so it should be mapped to
AXP288_IRQ_POKP where the last P stands for positive edge.
Likewise PEK_DBF should be mapped to the falling edge, aka the
_N_egative edge, so it should be mapped to AXP288_IRQ_POKN.
This fixes the inverted powerbutton status reporting by the
axp20x-pek driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp288 has the following irqs 2 times: VBUS_FALL, VBUS_RISE,
VBUS_OV. On boot / reset the enable flags for both the normal and alt
version of these irqs is set.
Since we were only listing the normal version in the axp288 regmap_irq
struct, we were never disabling the alt versions of these irqs.
Add the alt versions to the axp288 regmap_irq struct, so that these
get properly disabled.
Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The interrupt line of the entire family of axp2xx pmics is active-low,
for devicetree enumerated irqs, this is dealt with in the devicetree.
ACPI irq resources have a flag field for this too, I tried using this
on my CUBE iwork8 Air tablet, but it does not contain the right data.
The dstd shows the irq listed as either ActiveLow or ActiveHigh,
depending on the OSID variable, which seems to be set by the
"OS IMAGE ID" in the BIOS/EFI setup screen.
Since the acpi-resource info is no good, simply pass in IRQF_TRIGGER_LOW
on the axp288.
Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation of axp20x_device_remove() have a typo and use
axp20x_device_probe() as name. This patch fix this typo.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This declaration has never been used and is likely some left over from
early prototypes of the code, just remove it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PRCM block on the A23 contains a message box like interface to
the registers for the analog path controls of the internal codec.
Add a sub-device for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently we leak a lot of things when tearing down the IRQs this patch
fixes this cleaning up both the IRQ mappings and the IRQ domain itself.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have arizona_map_irq we might as well use it rather than hard coding
it in several places.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The macro TEST_VERIFY_AREA can never be defined as there's no
wp_works_ok variable. So just remove the dead code.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The parameter validation incorrectly returned an ERR_PTR(), which is not
handled by the callers to rpmsg_create_ept(), per the definition NULL
should be returned.
Fixes: 93e9324431 ("rpmsg: Handle invalid parameters in public API")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
tick_broadcast_lock is taken from interrupt context, but the following call
chain takes the lock without disabling interrupts:
[ 12.703736] _raw_spin_lock+0x3b/0x50
[ 12.703738] tick_broadcast_control+0x5a/0x1a0
[ 12.703742] intel_idle_cpu_online+0x22/0x100
[ 12.703744] cpuhp_invoke_callback+0x245/0x9d0
[ 12.703752] cpuhp_thread_fun+0x52/0x110
[ 12.703754] smpboot_thread_fn+0x276/0x320
So the following deadlock can happen:
lock(tick_broadcast_lock);
<Interrupt>
lock(tick_broadcast_lock);
intel_idle_cpu_online() is the only place which violates the calling
convention of tick_broadcast_control(). This was caused by the removal of
the smp function call in course of the cpu hotplug rework.
Instead of slapping local_irq_disable/enable() at the call site, we can
relax the calling convention and handle it in the core code, which makes
the whole machinery more robust.
Fixes: 29d7bbada9 ("intel_idle: Remove superfluous SMP fuction call")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Ruslan Ruslichenko <rruslich@cisco.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: lwn@lwn.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1486953115.5912.4.camel@gmx.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create a debugfs directory for every mockup chip and a single file
for every line. Writing (0 or 1) to these files allows the user to
inject line events (falling or rising edge respectively).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setup a dummy irqchip that will allow us to inject line events for
testing purposes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following sparse warning:
drivers/gpu/drm/bridge/ti-tfp410.c:223:24: warning:
symbol 'tfp410_platform_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209152549.30711-1-weiyj.lk@gmail.com
Currently unregistering sysctl table does not prune its dentries.
Stale dentries could slowdown sysctl operations significantly.
For example, command:
# for i in {1..100000} ; do unshare -n -- sysctl -a &> /dev/null ; done
creates a millions of stale denties around sysctls of loopback interface:
# sysctl fs.dentry-state
fs.dentry-state = 25812579 24724135 45 0 0 0
All of them have matching names thus lookup have to scan though whole
hash chain and call d_compare (proc_sys_compare) which checks them
under system-wide spinlock (sysctl_lock).
# time sysctl -a > /dev/null
real 1m12.806s
user 0m0.016s
sys 1m12.400s
Currently only memory reclaimer could remove this garbage.
But without significant memory pressure this never happens.
This patch collects sysctl inodes into list on sysctl table header and
prunes all their dentries once that table unregisters.
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> writes:
> On 10.02.2017 10:47, Al Viro wrote:
>> how about >> the matching stats *after* that patch?
>
> dcache size doesn't grow endlessly, so stats are fine
>
> # sysctl fs.dentry-state
> fs.dentry-state = 92712 58376 45 0 0 0
>
> # time sysctl -a &>/dev/null
>
> real 0m0.013s
> user 0m0.004s
> sys 0m0.008s
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Misc updates.
Miscellaneous updates include update of the firmware spec, ethtool flash
enhancement, ethtool -l minor fix, NTUPLE support enhancements, FEC
link settings message during link up, and new PCI IDs. Please review.
Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper puctuation to make the message more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print FEC (Forward Error Correction) autoneg and encoding settings during
link up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is a VF or an NPAR function, the firmware call to setup the PHY
will fail. Adding this check will prevent unnecessary firmware calls
to setup the PHY unless calling from the PF. This will also eliminate
many unnecessary warning messages when the call from a VF or NPAR fails.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>