commit e3c93e1a3f upstream.
As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.
This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().
This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 40384e4bbe upstream.
Correctly rollback state if the failure occurs after we have handed over
the ownership of the buffer to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a7117f81e8 upstream.
Driver forgot to unregister charger power supply if registering of
battery supply failed in probe(). In such case the memory associated
with power supply leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 68c3ed6fa7 upstream.
The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.
This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: da0a00ebc2 ("power: Add twl4030_madc battery driver.")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2f92b314f4 upstream.
USB ID 2001:330d is used for a D-Link DWA-131.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9374e7d2fd upstream.
Add new ID for ASUS N10 WiFi dongle.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a6615937bc upstream.
According to USB 2.0 ECN Errata for Link Power
Management (USB2-LPM-Errata-final.pdf), BESL
must be enabled if LPM is enabled.
This helps with USB30CV TD 9.21 LPM L1
Suspend Resume Test.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit aa8e22128b upstream.
If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.
Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging. The generic driver treats these as
errors.
Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3dfb05340e upstream.
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b815fc12d4 upstream.
This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.
Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bba0bdd7ad upstream.
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
BUG: unable to handle kernel paging request at ffffc9001a6bc084
IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib]
Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100)
Call Trace:
[<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp]
[<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp]
[<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod]
[<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod]
[<ffffffff81223b37>] __blk_run_queue+0x27/0x30
[<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110
[<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0
[<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod]
[<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod]
[<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod]
[<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod]
[<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod]
[<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod]
[<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod]
[<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod]
[<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160
[<ffffffff811589de>] vfs_write+0xce/0x140
[<ffffffff81158b53>] sys_write+0x53/0xa0
[<ffffffff81464592>] system_call_fastpath+0x16/0x1b
[<00007f611c9d9300>] 0x7f611c9d92ff
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2e7cee027b upstream.
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5df0582bf0 upstream.
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c9c52e2419 upstream.
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9c25210fd3 upstream.
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c7e8bdf587 upstream.
Fix a bug that leads to showing the name and description of C-state C0
as "<null>" in sysfs after the ACPI C-states changed (e.g. after AC->DC
or DC->AC
transition).
The function poll_idle_init() in drivers/cpuidle/driver.c initializes the
state 0 during cpuidle_register_driver(), so we better do not overwrite it
again with '\0' during acpi_processor_cst_has_changed().
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d75e4af14e upstream.
Thomas Schlichter reports the following issue on his Samsung NC20:
"The C-states C1 and C2 to the OS when connected to AC, and additionally
provides the C3 C-state when disconnected from AC. However, the number
of C-states shown in sysfs is fixed to the number of C-states present
at boot.
If I boot with AC connected, I always only see the C-states up to C2
even if I disconnect AC.
The reason is commit 130a5f6924 (ACPI / cpuidle: remove dev->state_count
setting). It removes the update of dev->state_count, but sysfs uses
exactly this variable to show the C-states.
The fix is to use drv->state_count in sysfs. As this is currently the
last user of dev->state_count, this variable can be completely removed."
Remove dev->state_count as per the above.
Reported-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c75de0ac07 upstream.
All CPUs leaving the first-online CPU are hotplugged out on suspend and
and cpufreq core stops managing them.
On resume, we need to call cpufreq_update_policy() for this CPU's policy
to make sure its frequency is in sync with cpufreq's cached value, as it
might have got updated by hardware during suspend/resume.
The policies are always added to the top of the policy-list. So, in
normal circumstances, CPU 0's policy will be the last one in the list.
And so the code checks for the last policy.
But there are cases where it will fail. Consider quad-core system, with
policy-per core. If CPU0 is hotplugged out and added back again, the
last policy will be on CPU1 :(
To fix this in a proper way, always look for the policy of the first
online CPU. That way we will be sure that we are calling
cpufreq_update_policy() for the only CPU that wasn't hotplugged out.
Fixes: 2f0aea9363 ("cpufreq: suspend governors on system suspend/hibernate")
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 05b676ab42 upstream.
TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it
should not be used for defining offset boundary for mmaping buffers for
CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on
the CAPTURE queue on 64bit architectures (like ARM64).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ab3120300b upstream.
The v4l2_dev field of struct video_device must be set correctly.
This was never done for this driver, so no video nodes were created
anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bc3b5b47c8 upstream.
I don't have this hardware but it looks like we weren't adding bridge
devices as intended. Maybe the bridge is always the last device?
Fixes: 05b1250048 ("PCI: cpcihp: Iterate over all devices in slot, not functions 0-7")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a1b7f2f636 upstream.
Commit fab4c256a5 ("PCI/AER: Add a TLP header print helper") introduced
the helper function __print_tlp_header(), but contrary to the intention,
the behaviour did change: Since we're taking the address of the parameter
t, the first 4 or 8 bytes printed will be the value of the pointer t
itself, and the remaining 12 or 8 bytes will be who-knows-what (something
from the stack).
We want to show the values of the four members of the struct
aer_header_log_regs; that can be done without ugly and error-prone casts.
On little-endian this should produce the same output as originally
intended, and since no-one has complained about getting garbage output so
far, I think big-endian should be ok too.
Fixes: fab4c256a5 ("PCI/AER: Add a TLP header print helper")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a415457733 upstream.
This device disconnects every 60s without X
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f5e2dc5d7f upstream.
Before commit 3900f29021 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.
The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7a1e890e21 upstream.
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1e9e39f4a2 upstream.
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 078fd7d630 upstream.
Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:
1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
we assume is always an ASM1051, so remove the quirk for 5106, and instead
use the same detection logic as we already use for device-id 55aa, which is
used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.
2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f20fbaad76 upstream.
`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length. It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow. For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long. If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address. Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.
Thanks to Dan Carpenter for reporting the potential integer overflow.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
[ luis: backported to 3.16: used backport provided by Ian ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit fb5ef9e7da upstream.
In canon mode, the read buffer head will advance over the buffer tail
if the input > 4095 bytes without receiving a line termination char.
Discard additional input until a line termination is received.
Before evaluating for overflow, the 'room' value is normalized for
I_PARMRK and 1 byte is reserved for line termination (even in !icanon
mode, in case the mode is switched). The following table shows the
transform:
actual buffer | 'room' value before overflow calc
space avail | !I_PARMRK | I_PARMRK
--------------------------------------------------
0 | -1 | -1
1 | 0 | 0
2 | 1 | 0
3 | 2 | 0
4+ | 3 | 1
When !icanon or when icanon and the read buffer contains newlines,
normalized 'room' values of -1 and 0 are clamped to 0, and
'overflow' is 0, so read_head is not adjusted and the input i/o loop
exits (setting no_room if called from flush_to_ldisc()). No input
is discarded since the reader does have input available to read
which ensures forward progress.
When icanon and the read buffer does not contain newlines and the
normalized 'room' value is 0, then overflow and room are reset to 1,
so that the i/o loop will process the next input char normally
(except for parity errors which are ignored). Thus, erasures, signalling
chars, 7-bit mode, etc. will continue to be handled properly.
If the input char processed was not a line termination char, then
the canon_head index will not have advanced, so the normalized 'room'
value will now be -1 and 'overflow' will be set, which indicates the
read_head can safely be reset, effectively erasing the last char
processed.
If the input char processed was a line termination, then the
canon_head index will have advanced, so 'overflow' is cleared to 0,
the read_head is not reset, and 'room' is cleared to 0, which exits
the i/o loop (because the reader now have input available to read
which ensures forward progress).
Note that it is possible for a line termination to be received, and
for the reader to copy the line to the user buffer before the
input i/o loop is ready to process the next input char. This is
why the i/o loop recomputes the room/overflow state with every
input char while handling overflow.
Finally, if the input data was processed without receiving
a line termination (so that overflow is still set), the pty
driver must receive a write wakeup. A pty writer may be waiting
to write more data in n_tty_write() but without unthrottling
here that wakeup will not arrive, and forward progress will halt.
(Normally, the pty writer is woken when the reader reads data out
of the buffer and more space become available).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 351fc4a99d upstream.
Intel IA32 SDM Table 15-14 defines channel 0xf as 'not specified', but
EDAC doesn't know about this and returns and INTERNAL ERROR when the
channel is greater than NUM_CHANNELS:
kernel: [ 1538.886456] CPU 0: Machine Check Exception: 0 Bank 1: 940000000000009f
kernel: [ 1538.886669] TSC 2bc68b22e7e812 ADDR 46dae7000 MISC 0 PROCESSOR 0:306e4 TIME 1390414572 SOCKET 0 APIC 0
kernel: [ 1538.971948] EDAC MC1: INTERNAL ERROR: channel value is out of range (15 >= 4)
kernel: [ 1538.972203] EDAC MC1: 0 CE memory read error on unknown memory (slot:0 page:0x46dae7 offset:0x0 grain:0 syndrome:0x0 - area:DRAM err_code:0000:009f socket:1 channel_mask:1 rank:0)
This commit changes sb_edac to forward a channel of -1 to EDAC if the
channel is not specified. edac_mc_handle_error() sets the channel to -1
internally after the error message anyway, so this commit should have no
effect other than avoiding the INTERNAL ERROR message when the channel
is not specified.
Signed-off-by: Seth Jennings <sjenning@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3b74729878 upstream.
Sometimes when the card is restarted it may cause -
"irq 16: nobody cared (try booting with the "irqpoll" option)"
that is likely caused so, that the card, after the hard reset
finishes, pulls on the irq. Disabling the ints before or after
the hpsa_kdump_hard_reset_controller fixes it.
At this point we can't know in which state the card is,
so using SA5_INTR_OFF + SA5_REPLY_INTR_MASK_OFFSET defines directly,
instead of the function the drivers provides, seems to be apropriate.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Masoud Sharbiani <msharbiani@twopensource.com>
Cc: Vinson Lee <vlee@twopensource.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 03741d956e upstream.
There is a potential memory leak in hpsa_kdump_hard_reset_controller.
Reviewed-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Masoud Sharbiani <msharbiani@twopensource.com>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 859c75aba2 upstream.
Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Masoud Sharbiani <msharbiani@twopensource.com>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 132aa220b4 upstream.
When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[ 16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Masoud Sharbiani <msharbiani@twopensource.com>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0c36820e2a upstream.
xen-netfront limits transmitted skbs to be at most 44 segments in size. However,
GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448
bytes each. This slight reduction in the size of packets means a slight loss in
efficiency.
Since c/s 9ecd1a75d, xen-netfront sets gso_max_size to
XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER,
where XEN_NETIF_MAX_TX_SIZE is 65535 bytes.
The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s
6c09fa09d) in determining when to split an skb into two is
sk->sk_gso_max_size - 1 - MAX_TCP_HEADER.
So the maximum permitted size of an skb is calculated to be
(XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER.
Intuitively, this looks like the wrong formula -- we don't need two TCP headers.
Instead, there is no need to deviate from the default gso_max_size of 65536 as
this already accommodates the size of the header.
Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments
of 1448 bytes each), as observed via tcpdump. This patch makes netfront send
skbs of up to 65160 bytes (45 segments of 1448 bytes each).
Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as
it relates to the size of the whole packet, including the header.
Fixes: 9ecd1a75d9 ("xen-netfront: reduce gso_max_size to account for max TCP header")
Signed-off-by: Jonathan Davies <jonathan.davies@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e5eda89d97 upstream.
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0cc ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8494057ab5 upstream.
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 02d88b735f upstream.
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5ca9e7ce6e upstream.
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4ce7ca89d6 upstream.
This patch uses iio_trigger_get to increment the reference
count of trigger device, to avoid incorrect assignment.
Can result in a null pointer dereference during removal if the
trigger has been changed before removal.
This patch refers to a similar situation encountered through the
following discussion:
http://www.spinics.net/lists/linux-iio/msg13669.html
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f54e9f2be3 upstream.
Depending on conversion mode used, the ADC clock (ADCK) needs
to be below a maximum frequency. According to Vybrid's data
sheet this is 20MHz for the low power conversion mode.
The ADC clock is depending on input clock, which is the bus
clock by default. Vybrid SoC are typically clocked at at 400MHz
or 500MHz, which leads to 66MHz or 83MHz bus clock respectively.
Hence, a divider of 8 is required to stay below the specified
maximum clock of 20MHz.
Due to the different bus clock speeds, the resulting sampling
frequency is not static. Hence use the ADC clock and calculate
the actual available sampling frequency dynamically.
This fixes bogous values observed on some 500MHz clocked Vybrid
SoC. The resulting value usually showed Bit 9 being stuck at 1,
or 0, which lead to a value of +/-512.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f2c9e560b4 upstream.
Use readb() and memcpy_fromio() accessors instead.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3899ca844b upstream.
Need to expand the check to handle short circuiting
if the selected state is the same as current state.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87796
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8e4934c6d6 upstream.
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b229a0f840 upstream.
This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order
to avoid attaching a TTY to the JTAG port as this board is based on the
CALAO Systems reference design and needs the same fix up.
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
[johan: clean up probe logic ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 227a4fd801 upstream.
When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.
However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set, an "Event Ring is Full" event
will be posted to the last entry of the event ring, but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring. That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.
This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c209 ("Intel xhci: Support EHCI/xHCI port switching.").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alistair Grant <akgrant0710@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9425183d17 upstream.
Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.
Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).
This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().
[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]
Reported-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3c56b3a12c upstream.
Commit 25b884a83d ("x86/xen: set
regions above the end of RAM as 1:1") introduced a regression.
To be able to add memory pages which were added via memory hotplug to
a pv domain, the pages must be "invalid" instead of "identity" in the
p2m list before they can be added.
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
