Remove "__" from __do_proc_do{intvec,uintvec,ulongvec_minmax} internal
functions and delete their corresponding do_proc_do* wrappers. These
indirections are unnecessary as they do not add extra logic nor do they
indicate a layer separation.
Signed-off-by: Joel Granados <joel.granados@kernel.org>
Remove superfluous tbl_data param from do_proc_douintvec{,_r,_w}
and __do_proc_do{intvec,uintvec,ulongvec_minmax}. There is no need to
pass it as it is always contained within the ctl_table struct.
Signed-off-by: Joel Granados <joel.granados@kernel.org>
* Replace void* data in the converter functions with a const struct
ctl_table* table as it was only getting forwarding values from
ctl_table->extra{1,2}.
* Remove the void* data in the do_proc_* functions as they already had a
pointer to the ctl_table.
* Remove min/max structures do_proc_do{uint,int}vec_minmax_conv_param;
the min/max values get passed directly in ctl_table.
* Keep min/max initialization in extra{1,2} in proc_dou8vec_minmax.
* The do_proc_douintvec was adjusted outside sysctl.c as it is exported
to fs/pipe.c.
Signed-off-by: Joel Granados <joel.granados@kernel.org>
Move enabling and disabling of interrupts around the SIE instruction to
entry code. Enabling interrupts only after the __TI_sie flag has been set
guarantees that the SIE instruction is not executed if an interrupt happens
between enabling interrupts and the execution of the SIE instruction.
Interrupt handlers and machine check handler forward the PSW to the
sie_exit label in such cases.
This is a prerequisite for VIRT_XFER_TO_GUEST_WORK to prevent that guest
context is entered when e.g. a scheduler IPI, indicating that a reschedule
is required, happens right before the SIE instruction, which could lead to
long delays.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Tested-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Add a signal_exits counter for s390, as exists on arm64, loongarch, mips,
powerpc, riscv and x86.
This is used by kvm_handle_signal_exit(), which we will use when we
later enable CONFIG_VIRT_XFER_TO_GUEST_WORK.
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
The Extended Supported Rates (ESR) IE handling in OnBeacon accessed
*(p + 1 + ielen) and *(p + 2 + ielen) without verifying that these
offsets lie within the received frame buffer. A malformed beacon with
an ESR IE positioned at the end of the buffer could cause an
out-of-bounds read, potentially triggering a kernel panic.
Add a boundary check to ensure that the ESR IE body and the subsequent
bytes are within the limits of the frame before attempting to access
them.
This prevents OOB reads caused by malformed beacon frames.
Signed-off-by: Navaneeth K <knavaneeth786@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Supported Rates IE length from an incoming Association Request frame
was used directly as the memcpy() length when copying into a fixed-size
16-byte stack buffer (supportRate). A malicious station can advertise an
IE length larger than 16 bytes, causing a stack buffer overflow.
Clamp ie_len to the buffer size before copying the Supported Rates IE,
and correct the bounds check when merging Extended Supported Rates to
prevent a second potential overflow.
This prevents kernel stack corruption triggered by malformed association
requests.
Signed-off-by: Navaneeth K <knavaneeth786@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Information Element (IE) parser rtw_get_ie() trusted the length
byte of each IE without validating that the IE body (len bytes after
the 2-byte header) fits inside the remaining frame buffer. A malformed
frame can advertise an IE length larger than the available data, causing
the parser to increment its pointer beyond the buffer end. This results
in out-of-bounds reads or, depending on the pattern, an infinite loop.
Fix by validating that (offset + 2 + len) does not exceed the limit
before accepting the IE or advancing to the next element.
This prevents OOB reads and ensures the parser terminates safely on
malformed frames.
Signed-off-by: Navaneeth K <knavaneeth786@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, VRAM TTM resource manager debugfs entries (vram0_mm / vram1_mm)
were created globally in the XE debugfs root directory. But technically,
each tile has an associated VRAM TTM manager, which it can own.
Let's create VRAM memory manager debugfs entries directly under each tile's
debugfs directory for better alignment with the per-tile memory layout.
Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patch.msgid.link/20251127073643.144379-1-piotr.piorkowski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
pf_descriptor_init currently returns a size_t, which is an unsigned
integer data type. This conflicts with it returning a negative errno
value on failure.
Make it return an int instead. This mirrors how pf_trailer_init is used
later.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Alex Zuo <alex.zuo@intel.com>
Link: https://patch.msgid.link/20251117190114.69953-2-jonathan.cavitt@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
This code doesn't run. Since 2008:
4f9c11dd49 ("x86, 64-bit: adjust mapping of physical pagetables to work with Xen")
the kernel has gained more flexible logging and tracing capabilities;
presumably if anyone wanted to take advantage of this log message they would
have got rid of the "if (0)" so they could use these capabilities.
Since they haven't, just delete it.
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/20251003-x86-init-cleanup-v1-1-f2b7994c2ad6@google.com
This commit updates the initialization for the "srcu-fast" scale
type to use DEFINE_STATIC_SRCU_FAST() when reader_flavor is equal to
SRCU_READ_FLAVOR_FAST.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <bpf@vger.kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
This commit causes rcutorture's srcu_torture_init() and
srcud_torture_init() functions to announce on the console log
which variant of SRCU is being tortured, for example: "torture:
srcud_torture_init fast SRCU".
[ paulmck: Apply feedback from kernel test robot. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
This commit creates an SRCU-fast-updown API, including
DEFINE_SRCU_FAST_UPDOWN(), DEFINE_STATIC_SRCU_FAST_UPDOWN(),
__init_srcu_struct_fast_updown(), init_srcu_struct_fast_updown(),
srcu_read_lock_fast_updown(), srcu_read_unlock_fast_updown(),
__srcu_read_lock_fast_updown(), and __srcu_read_unlock_fast_updown().
These are initially identical to their SRCU-fast counterparts, but both
SRCU-fast and SRCU-fast-updown will be optimized in different directions
by later commits. SRCU-fast will lack any sort of srcu_down_read() and
srcu_up_read() APIs, which will enable extremely efficient NMI safety.
For its part, SRCU-fast-updown will not be NMI safe, which will enable
reasonably efficient implementations of srcu_down_read_fast() and
srcu_up_read_fast().
This API fork happens to meet two different future use cases.
* SRCU-fast will become the reimplementation basis for RCU-TASK-TRACE
for consolidation. Since RCU-TASK-TRACE must be NMI safe, SRCU-fast
must be as well.
* SRCU-fast-updown will be needed for uretprobes code in order to get
rid of the read-side memory barriers while still allowing entering the
reader at task level while exiting it in a timer handler.
This commit also adds rcutorture tests for the new APIs. This
(annoyingly) needs to be in the same commit for bisectability. With this
commit, the 0x8 value tests SRCU-fast-updown. However, most SRCU-fast
testing will be via the RCU Tasks Trace wrappers.
[ paulmck: Apply s/0x8/0x4/ missing change per Boqun Feng feedback. ]
[ paulmck: Apply Akira Yokosawa feedback. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <bpf@vger.kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
In Store and Forward mode, flushing frames when the receive buffer is
unavailable, can cause the MTL Rx FIFO to go out of sync. This results
in buffering of a few frames in the FIFO without triggering Rx DMA
from transferring the data to the system memory until another packet
is received. Once the issue happens, for a ping request, the packet is
forwarded to the system memory only after we receive another packet
and hece we observe a latency equivalent to the ping interval.
64 bytes from 192.168.2.100: seq=1 ttl=64 time=1000.344 ms
Also, we can observe constant gmacgrp_debug register value of
0x00000120, which indicates "Reading frame data".
The issue is not reproducible after disabling frame flushing when Rx
buffer is unavailable. But in that case, the Rx DMA enters a suspend
state due to buffer unavailability. To resume operation, software
must write to the receive_poll_demand register after adding new
descriptors, which reactivates the Rx DMA.
This issue is observed in the socfpga platforms which has dwmac1000 IP
like Arria 10, Cyclone V and Agilex 7. Issue is reproducible after
running iperf3 server at the DUT for UDP lower packet sizes.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251126-a10_ext_fix-v1-1-d163507f646f@altera.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace mutex_init() with the devm_mutex_init(), to ensure proper mutex
cleanup during probe failure and driver removal.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://patch.msgid.link/20251119085813.546813-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Define a new macro BIOS_INPUTS_MAX, to represent the maximum number of
BIOS input values. Replace hardcoded array sizes in relevant structures
with this macro to improve readability and maintainability.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Tested-by: Yijun Shen <Yijun.Shen@Dell.com>
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251119085813.546813-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
gcc 13, in some cases, gets confused if the __builtin_constant_p() is
inside the switch. It thinks that bitnr can have the value max+1 and
fails. Lift the check outside the switch to avoid it.
Fixes: ef7bfe5bbf ("iommupt/x86: Support SW bits and permit PT_FEAT_DMA_INCOHERENT")
Fixes: 5448c1558f ("iommupt: Add the Intel VT-d second stage page table format")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511242012.I7g504Ab-lkp@intel.com/
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add dt-bindings documentation of SPI NAND controller
for Airoha EN7523 SoC platform.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251125234047.1101985-3-mikhail.kshevetskiy@iopsys.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Airoha EN7523 specific bug
--------------------------
We found that some serial console may pull TX line to GROUND during board
boot time. Airoha uses TX line as one of its bootstrap pins. On the EN7523
SoC this may lead to booting in RESERVED boot mode.
It was found that some flashes operates incorrectly in RESERVED mode.
Micron and Skyhigh flashes are definitely affected by the issue,
Winbond flashes are not affected.
Details:
--------
DMA reading of odd pages on affected flashes operates incorrectly. Page
reading offset (start of the page) on hardware level is replaced by 0x10.
Thus results in incorrect data reading. As result OS loading becomes
impossible.
Usage of UBI make things even worse. On attaching, UBI will detects
corruptions (because of wrong reading of odd pages) and will try to
recover. For recovering UBI will erase and write 'damaged' blocks with
a valid information. This will destroy all UBI data.
Non-DMA reading is OK.
This patch detects booting in reserved mode, turn off DMA and print big
fat warning.
It's worth noting that the boot configuration is preserved across reboots.
Therefore, to boot normally, you should do the following:
- disconnect the serial console from the board,
- power cycle the board.
Fixes: a403997c12 ("spi: airoha: add SPI-NAND Flash controller driver")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://patch.msgid.link/20251125234047.1101985-2-mikhail.kshevetskiy@iopsys.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Use kvzalloc() instead of kzalloc() to allocate memory to cache the
content of a firmware control.
Most firmware controls are only small, typically a few bytes. But on
some firmware there can be much larger controls for coefficient or
model data.
The overhead of kvzalloc() is negligible because most control allocs
can be satisfied by the normal kmalloc() that kvzalloc() will try first.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251127103947.1094934-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In cs_dsp_debugfs_read_controls_show() take the pwr_lock mutex
around the list walk. This protects against debugfs returning
a partial set of new controls if those controls are being added
to the list while it is being walked.
Controls are never deleted from this list, and are only added to
the end of the list. So there was never a danger of following a
stale pointer to garbage.
The worst case was that the printed list is truncated if it saw an
entry that was the list end just before a new entry was appended to
the list.
With the original code, the truncated list from the debugfs could
show only _some_ of the new entries. This could be confusing because
it appears that some new entries are missing.
Adding the mutex means that the debugfs read provides an atomic view.
Either it shows the old content before any of the new controls were
added; or it shows the new content after all the new controls are
added.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251127113238.1251352-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if something goes wrong when performing suspend on DSP, from the
system perspective the component is not critical enough to block the
suspend operation entirely. Leaving recovery to next resume() suffices.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20251126095523.3925364-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
catpt_dai_pcm_new() is called during the bring up sequence of the
machine board device which is a different device to the parent (DSP)
device yet utilizes pm_runtime_xxx() against it in order to send IPCs.
If the parent's pm_runtime is not configured before that happens,
errors will occur.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251126095523.3925364-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not leave any resources hanging on the DSP side if
applying user settings fails.
Fixes: 768a3a3b32 ("ASoC: Intel: catpt: Optimize applying user settings")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251126095523.3925364-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a number of interfaces available for manipulating instances of
struct resource. To improve readability, move away from manual editing
in favor of the common interface.
While at it, adjust spacing so that both code blocks, while found in
separate functions, looks cohesive.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251126095523.3925364-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Verify if the entire block is found within DRAM, not just
the start of it.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251126095523.3925364-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Propagate fwnode of the ACPI device to the SPI controller Linux device.
Currently only OF case propagates fwnode to the controller.
While at it, replace several calls to dev_fwnode() with a single one
cached in a local variable, and unify checks for fwnode type by using
is_*_node() APIs.
Fixes: 55ab8487e0 ("spi: spi-nxp-fspi: Add ACPI support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://patch.msgid.link/20251126202501.2319679-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wei Fang says:
====================
net: fec: fix some PTP related issues
There are some issues which were introduced by the commit 350749b909
("net: fec: Add support for periodic output signal of PPS"). See each
patch for more details.
====================
Link: https://patch.msgid.link/20251125085210.1094306-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On transmit, we are currently relying on skb->dev being set by
mctp_local_output() when we first set up the skb destination fields.
However, forwarded skbs do not use the local_output path, so will retain
their incoming netdev as their ->dev on tx. This does not work when
we're forwarding between interfaces.
Set skb->dev unconditionally in the transmit path, to allow for proper
forwarding.
We keep the skb->dev initialisation in mctp_local_output(), as we use it
for fragmentation.
Fixes: 269936db5e ("net: mctp: separate routing database from routing operations")
Suggested-by: Vince Chang <vince_chang@aspeedtech.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20251125-dev-forward-v1-1-54ecffcd0616@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tas2781-hda supports multi-projects. In some projects, GpioInt() was
dropped due to no IRQ connection. See the example code below:
Device (SPKR)
{
Name (_ADR, One)
Name (_HID, "TXNW2781")
Method (_CRS, 0, NotSerialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0038, ...)
I2cSerialBusV2 (0x0039, ...)
// GpioInt (Edge, ...) { 0x0000 }
//"GpioInt (...) {}" was commented out due to no IRQ connection.
})
Return (RBUF)
}
}
But in smi_i2c_probe(), smi_spi_probe() (serial-multi-instantiate.c), if
looking for IRQ by smi_get_irq() fails, it will return an error, will not add
new device, and cause smi_probe() to fail:
[ 2.356546] Serial bus multi instantiate pseudo device driver TXNW2781:00:
error -ENXIO: IRQ index 0 not found
[ 2.356561] Serial bus multi instantiate pseudo device driver TXNW2781:00:
error -ENXIO: Error requesting irq at index 0
So, we need to add an exception case for these situations. BTW, this patch
will take effect on both I2C and SPI devices.
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251126141434.11110-1-baojun.xu@ti.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
debugfs access modes were added in Linux 5.10 (Dec 2020) [1], but the
no-mount mode has behaved effectively the same as the off mode since
Linux 5.12 (Apr 2021) [2]. The only difference is the specific error
code returned by the debugfs_create_* functions, which is -ENOENT in
no-mount mode and -EPERM in off mode.
Given that no-mount hasn't worked for several years with no complaints,
just remove it.
[1] a24c6f7bc9 ("debugfs: Add access restriction option")
[2] bc6de804d3 ("debugfs: be more robust at handling improper input in debugfs_lookup()")
56348560d4 ("debugfs: do not attempt to create a new file before the filesystem is initalized")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Link: https://patch.msgid.link/20251120102222.18371-3-dev@null.aaront.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
debugfs_get_tree() can only be called if debugfs itself calls
simple_pin_fs() or register_filesystem(), and those call paths also
check the access mode.
debugfs_start_creating() checks the access mode so the checks in the
debugfs_create_* functions are unnecessary.
An upcoming change will affect debugfs_allow, so doing this cleanup
first will make that change simpler.
Signed-off-by: Aaron Thompson <dev@aaront.org>
Link: https://patch.msgid.link/20251120102222.18371-2-dev@null.aaront.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Duyck says:
====================
net: phy: Add support for fbnic PHY w/ 25G, 50G, and 100G support
To transition the fbnic driver to using the XPCS driver we need to address
the fact that we need a representation for the FW managed PMD that is
actually a SerDes PHY to handle link bouncing during link training.
This patch set introduces the necessary bits to the XPCS driver code to
enable it to read 25G, 50G, and 100G speeds from the PCS ctrl1 register,
and adds support for the approriate interfaces.
The rest of this patch set enables the changes to fbnic to make use of
these interfaces and expose a PMD that can provide a necessary link delay
to avoid link flapping in the event that a cable is disconnected and
reconnected, and to correctly expose the count for the link down events.
With this we have the basic groundwork laid as with this all the bits and
pieces are in place in terms of reading the configuration. The general plan
for follow-on patch sets is to start looking at enabling changing the
configuration in environments where that is supported.
====================
Link: https://patch.msgid.link/176374310349.959489.838154632023183753.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As we have exposed the PCS registers via the SWMII we can now start looking
at connecting the XPCS driver to those registers and let it mange the PCS
instead of us doing it directly from the fbnic driver.
For now this just gets us the ability to detect link. The hope is in the
future to add some of the vendor specific registers to begin enabling XPCS
configuration of the interface.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374325295.959489.14521115864034905277.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
