This far using crtc_state->pipe_src as borders for Selective Update area
haven't caused visible problems as drm_rect_width(crtc_state->pipe_src) ==
crtc_state->hw.adjusted_mode.crtc_hdisplay and
drm_rect_height(crtc_state->pipe_src) ==
crtc_state->hw.adjusted_mode.crtc_vdisplay when pipe scaling is not
used. On the other hand using pipe scaling is forcing full frame updates and all the
Selective Update area calculations are skipped. Now this improper usage of
crtc_state->pipe_src is causing following warnings:
<4> [7771.978166] xe 0000:00:02.0: [drm] drm_WARN_ON_ONCE(su_lines % vdsc_cfg->slice_height)
after WARN_ON_ONCE was added by commit:
"drm/i915/dsc: Add helper for writing DSC Selective Update ET parameters"
These warnings are seen when DSC and pipe scaling are enabled
simultaneously. This is because on full frame update SU area is improperly
set as pipe_src which is not aligned with DSC slice height.
Fix these by creating local rectangle using
crtc_state->hw.adjusted_mode.crtc_hdisplay and
crtc_state->hw.adjusted_mode.crtc_vdisplay. Use this local rectangle as
borders for SU area.
Fixes: d6774b8c3c ("drm/i915: Ensure damage clip area is within pipe area")
Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patch.msgid.link/20260327114553.195285-1-jouni.hogander@intel.com
(cherry picked from commit da0cdc1c32)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The JMicron JMB585 (and JMB582) SATA controllers advertise 64-bit DMA
support via the S64A bit in the AHCI CAP register, but their 64-bit DMA
implementation is defective. Under sustained I/O, DMA transfers targeting
addresses above 4GB silently corrupt data -- writes land at incorrect
memory addresses with no errors logged.
The failure pattern is similar to the ASMedia ASM1061
(commit 20730e9b27 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers")), which also falsely advertised full 64-bit DMA
support. However, the JMB585 requires a stricter 32-bit DMA mask rather
than 43-bit, as corruption occurs with any address above 4GB.
On the Minisforum N5 Pro specifically, the combination of the JMB585's
broken 64-bit DMA with the AMD Family 1Ah (Strix Point) IOMMU causes
silent data corruption that is only detectable via checksumming
filesystems (BTRFS/ZFS scrub). The corruption occurs when 32-bit IOVA
space is exhausted and the kernel transparently switches to 64-bit DMA
addresses.
Add device-specific PCI ID entries for the JMB582 (0x0582) and JMB585
(0x0585) before the generic JMicron class match, using a new board type
that combines AHCI_HFLAG_IGN_IRQ_IF_ERR (preserving existing behavior)
with AHCI_HFLAG_32BIT_ONLY to force 32-bit DMA masks.
Signed-off-by: Arthur Husband <artmoty@gmail.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The automatic skipping of tests on ENOSYS returns was introduced in
commit 349afc8a52 ("selftests/nolibc: skip tests for unimplemented
syscalls"). It handled the fact that nolibc would return ENOSYS for many
syscall wrappers on riscv32.
Nowadays nolibc handles all these correctly, so this logic is not used
anymore. To make missing nolibc functionality more obvious fail the
tests again if something is not implemented.
Revert the mentioned commit again.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260406-nolibc-no-skip-enosys-v1-2-c046b1ac7d73@weissschuh.net/
Add some standard functions to convert between different byte orders.
Conveniently the UAPI headers provide all the necessary functionality.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260405-nolibc-bswap-v1-1-f7699ca9cee0@weissschuh.net
The standard syscall() function or macro uses the libc return value
convention. Errors returned from the kernel as negative values are
stored in errno and -1 is returned. Users who want to avoid using
errno don't have a way to call raw syscalls and check the returned
error.
Add a new macro _syscall() which works like the standard syscall()
but passes through the return value from the kernel unchanged.
The naming scheme and return values match the named _sys_foo()
system call wrappers already part of nolibc.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260405-nolibc-syscall-v1-3-e5b12bc63211@weissschuh.net
__sysret() transforms the return value from the kernel into the libc
return value convention. There is no reason for it to be called in the
middle of the internals of the syscall() implementation macros.
Move the call up, directly into syscall(), to make the code simpler.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260405-nolibc-syscall-v1-2-e5b12bc63211@weissschuh.net
These macros are the internal implementation of syscall().
They can not be used by users. Align them with the standard naming
scheme for internal symbols.
The current name also prevents the addition of an application-usable
_syscall() symbol.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260405-nolibc-syscall-v1-1-e5b12bc63211@weissschuh.net
to_ratio() computes BW_SHIFT-scaled bandwidth ratios from u64 period and
runtime values, but it returns unsigned long. tg_rt_schedulable() also
stores the current group limit and the accumulated child sum in unsigned
long.
On 32-bit builds, large bandwidth ratios can be truncated and the RT
group sum can wrap when enough siblings are present. That can let an
overcommitted RT hierarchy pass the schedulability check, and it also
narrows the helper result for other callers.
Return u64 from to_ratio() and use u64 for the RT group totals so
bandwidth ratios are preserved and compared at full width on both 32-bit
and 64-bit builds.
Fixes: b40b2e8eb5 ("sched: rt: multi level group constraints")
Assisted-by: Codex:GPT-5
Signed-off-by: Joseph Salisbury <joseph.salisbury@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260403210014.2713404-1-joseph.salisbury@oracle.com
- Dinh & Yury's changes to use sysfs_emit() for sysfs read
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Sorry for the late post due to personal affairs.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
-----BEGIN PGP SIGNATURE-----
iIkEABYIADEWIQSgSJpClIeaArXyudb8twOBpKCM2gUCadRyjxMceWlsdW4ueHVA
aW50ZWwuY29tAAoJEPy3A4GkoIzaU7wBAMABdw6I4GNfj9NjwYhup0vP8KXmR8tu
fSsuMEfwiNBnAQDyEXq6/Ll8V5uX4TukAeJegKU6CO/4OUblFLo918ueBw==
=Qmik
-----END PGP SIGNATURE-----
Merge tag 'fpga-for-7.1-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next
Xu writes:
FPGA Manager changes for 7.1-rc1
- Dinh & Yury's changes to use sysfs_emit() for sysfs read
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Sorry for the late post due to personal affairs.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-7.1-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: m10bmc-sec: switch show_canceled_csk() to using sysfs_emit()
fpga: bridge: Use sysfs_emit() instead of sprintf()
When retry_aligned_read() encounters an overlapped stripe, it releases
the stripe via raid5_release_stripe() which puts it on the lockless
released_stripes llist. In the next raid5d loop iteration,
release_stripe_list() drains the stripe onto handle_list (since
STRIPE_HANDLE is set by the original IO), but retry_aligned_read()
runs before handle_active_stripes() and removes the stripe from
handle_list via find_get_stripe() -> list_del_init(). This prevents
handle_stripe() from ever processing the stripe to resolve the
overlap, causing an infinite loop and soft lockup.
Fix this by using __release_stripe() with temp_inactive_list instead
of raid5_release_stripe() in the failure path, so the stripe does not
go through the released_stripes llist. This allows raid5d to break out
of its loop, and the overlap will be resolved when the stripe is
eventually processed by handle_stripe().
Fixes: 773ca82fa1 ("raid5: make release_stripe lockless")
Cc: stable@vger.kernel.org
Signed-off-by: FengWei Shih <dannyshih@synology.com>
Signed-off-by: Chia-Ming Chang <chiamingc@synology.com>
Link: https://lore.kernel.org/linux-raid/20260402061406.455755-1-chiamingc@synology.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
The third argument in INTEL_UNCORE_FR_EVENT_DESC() is subject to
__stringify(), and the extra double quote marks can result in the
expansion "3.814697266e-6" in the sysfs knobs, instead of
3.814697266e-6.
This is incorrect, though it may still work for perf, e.g.
perf stat -e uncore_iio_free_running_0/bw_in_port0/
Fixes: d8987048f6 ("perf/x86/intel/uncore: Support IIO free-running counters on DMR")
Closes: https://lore.kernel.org/all/20251231224233.113839-1-zide.chen@intel.com/
Reported-by: Chun-Tse Shao <ctshao@google.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chun-Tse Shao <ctshao@google.com>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://patch.msgid.link/20260313174050.171704-5-zide.chen@intel.com
In snbep_pci2phy_map_init(), in the nr_node_ids > 8 path,
uncore_device_to_die() may return -1 when all CPUs associated
with the UBOX device are offline.
Remove the WARN_ON_ONCE(die_id == -1) check for two reasons:
- The current code breaks out of the loop. This is incorrect because
pci_get_device() does not guarantee iteration in domain or bus order,
so additional UBOX devices may be skipped during the scan.
- Returning -EINVAL is incorrect, since marking offline buses with
die_id == -1 is expected and should not be treated as an error.
Separately, when NUMA is disabled on a NUMA-capable platform,
pcibus_to_node() returns NUMA_NO_NODE, causing uncore_device_to_die()
to return -1 for all PCI devices. As a result,
spr_update_device_location(), used on Intel SPR and EMR, ignores the
corresponding PMON units and does not add them to the RB tree.
Fix this by using uncore_pcibus_to_dieid(), which retrieves topology
from the UBOX GIDNIDMAP register and works regardless of whether NUMA
is enabled in Linux. This requires snbep_pci2phy_map_init() to be
added in spr_uncore_pci_init().
Keep uncore_device_to_die() only for the nr_node_ids > 8 case, where
NUMA is expected to be enabled.
Fixes: 9a7832ce3d ("perf/x86/intel/uncore: With > 8 nodes, get pci bus die id from NUMA info")
Fixes: 65248a9a9e ("perf/x86/uncore: Add a quirk for UPI on SPR")
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://patch.msgid.link/20260313174050.171704-4-zide.chen@intel.com
This warning can be triggered if NUMA is disabled and the system
boots with fewer CPUs than the number of CPUs in die 0.
WARNING: CPU: 9 PID: 7257 at uncore.c:1157 uncore_pci_pmu_register+0x136/0x160 [intel_uncore]
Currently, the discovery table continues to be parsed even if all CPUs
in the associated die are offline. This can lead to an array overflow
at "pmu->boxes[die] = box" in uncore_pci_pmu_register(), which may
trigger the warning above or cause other issues.
Fixes: edae1f06c2 ("perf/x86/intel/uncore: Parse uncore discovery tables")
Reported-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://patch.msgid.link/20260313174050.171704-3-zide.chen@intel.com
Kernel test robot reported:
Unverified Error/Warning (likely false positive, kindly check if
interested):
arch/x86/events/intel/uncore_discovery.c:293:2-8:
ERROR: missing iounmap; ioremap on line 288 and execution via
conditional on line 292
If domain->global_init() fails in __parse_discovery_table(), the
ioremap'ed MMIO region is not released before returning, resulting
in an MMIO mapping leak.
Fixes: b575fc0e33 ("perf/x86/intel/uncore: Add domain global init callback")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://patch.msgid.link/20260313174050.171704-2-zide.chen@intel.com
The Snapdragon 670 has an Low-Power Island (LPI) TLMM for configuring
pins related to audio. Add the driver for this.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add the pin controller for the audio Low-Power Island (LPI) on SDM670.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
There can be reserved GPIOs on the LPASS LPI pin controller to possibly
control sensors. Add the property for reserved GPIOs so they can be
avoided appropriately.
Adapted from the same entry in qcom,tlmm-common.yaml.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Use a flexible array member and kzalloc_flex to combine allocations.
Add __counted_by for extra runtime analysis. Move counting variable
assignment after allocation. kzalloc_flex with GCC >= 15 does this
automatically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* Fix 1kOhm, debounce, and PWM capability support
* Add support for new PAD_OWN layout
-----BEGIN PGP SIGNATURE-----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=Ob1Q
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v7.0-2
* Fix 1kOhm, debounce, and PWM capability support
* Add support for new PAD_OWN layout
Signed-off-by: Linus Walleij <linusw@kernel.org>
aiptek_irq() derives macro key indices directly from tablet reports and
then uses them to index macroKeyEvents[]. Report types 4 and 5 also save
the derived value in aiptek->lastMacro and later use that state to
release the previous key.
Validate the raw macro index once before it enters that state machine, so
lastMacro only ever stores an in-range macro key. Keep direct bounds
checks for report type 6, which reads the macro number from the packet
body and uses it immediately.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260329001711.88076-1-pengpeng@iscas.ac.cn
[dtor: fix macro fallback in report 5s to use -1]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gf2k_read() decodes the hat position from a 4-bit field and uses it
directly to index gf2k_hat_to_axis[]. The lookup table only has nine
entries, so malformed packets can read past the end of the fixed table.
Skip hat reporting when the decoded value falls outside the lookup
table instead of forcing it to the neutral position. This keeps the
fix local and avoids reporting a made-up axis state for malformed
packets.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260407120001.1-gf2k-v2-pengpeng@iscas.ac.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
During raid456 reshape, direct IO across the reshape position can sleep
in raid5_make_request() waiting for reshape progress while still
holding an active_io reference. If userspace then freezes reshape and
writes md/suspend_lo or md/suspend_hi, mddev_suspend() kills active_io
and waits for all in-flight IO to drain.
This can deadlock: the IO needs reshape progress to continue, but the
reshape thread is already frozen, so the active_io reference is never
dropped and suspend never completes.
raid5_prepare_suspend() already wakes wait_for_reshape for dm-raid. Do
the same for normal md suspend when reshape is already interrupted, so
waiting raid456 IO can abort, drop its reference, and let suspend
finish.
The mdadm test tests/25raid456-reshape-deadlock reproduces the hang.
Fixes: 714d20150e ("md: add new helpers to suspend/resume array")
Link: https://lore.kernel.org/linux-raid/20260327140729.2030564-1-yukuai@fnnas.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Previously, using wait_event() would wake up all waiters simultaneously,
and they would compete for the tree lock. The bio which gets the lock
first will be handled, so the write sequence cannot be guaranteed.
For example:
bio1(100,200)
bio2(150,200)
bio3(150,300)
The write sequence of fast device is bio1,bio2,bio3. But the write sequence
of slow device could be bio1,bio3,bio2 due to lock competition. This causes
data corruption.
Replace waitqueue with a fifo list to guarantee the write sequence. And it
also needs to iterate the list when removing one entry. If not, it may miss
the opportunity to wake up the waiting io.
For example:
bio1(1,3), bio2(2,4)
bio3(5,7), bio4(6,8)
These four bios are in the same bucket. bio1 and bio3 are inserted into
the rbtree. bio2 and bio4 are added to the waiting list and bio2 is the
first one. bio3 returns from slow disk and tries to wake up the waiting
bios. bio2 is removed from the list and will be handled. But bio1 hasn't
finished. So bio2 will be added into waiting list again. Then bio1 returns
from slow disk and wakes up waiting bios. bio4 is removed from the list
and will be handled. Now bio1, bio3 and bio4 all finish and bio2 is left
on the waiting list. So it needs to iterate the waiting list to wake up
the right bio.
Signed-off-by: Xiao Ni <xni@redhat.com>
Link: https://lore.kernel.org/linux-raid/20260324072501.59865-1-xni@redhat.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
For RAID-456 arrays with llbitmap, if all underlying disks support
write_zeroes with unmap, issue write_zeroes to zero all disk data
regions and initialize the bitmap to BitCleanUnwritten instead of
BitUnwritten.
This optimization skips the initial XOR parity building because:
1. write_zeroes with unmap guarantees zeroed reads after the operation
2. For RAID-456, when all data is zero, parity is automatically
consistent (0 XOR 0 XOR ... = 0)
3. BitCleanUnwritten indicates parity is valid but no user data
has been written
The implementation adds two helper functions:
- llbitmap_all_disks_support_wzeroes_unmap(): Checks if all active
disks support write_zeroes with unmap
- llbitmap_zero_all_disks(): Issues blkdev_issue_zeroout() to each
rdev's data region to zero all disks
The zeroing and bitmap state setting happens in llbitmap_init_state()
during bitmap initialization. If any disk fails to zero, we fall back
to BitUnwritten and normal lazy recovery.
This significantly reduces array initialization time for RAID-456
arrays built on modern NVMe SSDs or other devices that support
write_zeroes with unmap.
Reviewed-by: Xiao Ni <xni@redhat.com>
Link: https://lore.kernel.org/linux-raid/20260323054644.3351791-4-yukuai@fnnas.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Add new states to the llbitmap state machine to support proactive XOR
parity building for RAID-5 arrays. This allows users to pre-build parity
data for unwritten regions before any user data is written.
New states added:
- BitNeedSyncUnwritten: Transitional state when proactive sync is triggered
via sysfs on Unwritten regions.
- BitSyncingUnwritten: Proactive sync in progress for unwritten region.
- BitCleanUnwritten: XOR parity has been pre-built, but no user data
written yet. When user writes to this region, it transitions to BitDirty.
New actions added:
- BitmapActionProactiveSync: Trigger for proactive XOR parity building.
- BitmapActionClearUnwritten: Convert CleanUnwritten/NeedSyncUnwritten/
SyncingUnwritten states back to Unwritten before recovery starts.
State flows:
- Current (lazy): Unwritten -> (write) -> NeedSync -> (sync) -> Dirty -> Clean
- New (proactive): Unwritten -> (sysfs) -> NeedSyncUnwritten -> (sync) -> CleanUnwritten
- On write to CleanUnwritten: CleanUnwritten -> (write) -> Dirty -> Clean
- On disk replacement: CleanUnwritten regions are converted to Unwritten
before recovery starts, so recovery only rebuilds regions with user data
A new sysfs interface is added at /sys/block/mdX/md/llbitmap/proactive_sync
(write-only) to trigger proactive sync. This only works for RAID-456 arrays.
Link: https://lore.kernel.org/linux-raid/20260323054644.3351791-3-yukuai@fnnas.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
r5c_recovery_analyze_meta_block() and
r5l_recovery_verify_data_checksum_for_mb() iterate over payloads in a
journal metadata block using on-disk payload size fields without
validating them against the remaining space in the metadata block.
A corrupted journal contains payload sizes extending beyond the PAGE_SIZE
boundary can cause out-of-bounds reads when accessing payload fields or
computing offsets.
Add bounds validation for each payload type to ensure the full payload
fits within meta_size before processing.
Fixes: b4c625c673 ("md/r5cache: r5cache recovery: part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Link: https://lore.kernel.org/linux-raid/SYBPR01MB78815E78D829BB86CD7C8015AF5FA@SYBPR01MB7881.ausprd01.prod.outlook.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
The md_wq workqueue is defined as static and initialized in md_init(),
but it is not used anywhere within md.c.
All asynchronous and deferred work in this file is handled via
md_misc_wq or dedicated md threads.
Fixes: b75197e86e ("md: Remove flush handling")
Signed-off-by: Abd-Alrhman Masalkhi <abd.masalkhi@gmail.com>
Link: https://lore.kernel.org/linux-raid/20260328193522.3624-1-abd.masalkhi@gmail.com/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
syzbot reported a WARNING at mm/page_alloc.c:__alloc_frozen_pages_noprof()
triggered by create_strip_zones() in the RAID0 driver.
When raid_disks is large, the allocation size exceeds MAX_PAGE_ORDER (4MB
on x86), causing WARN_ON_ONCE_GFP(order > MAX_PAGE_ORDER).
Convert the strip_zone and devlist allocations from kzalloc/kzalloc_objs to
kvzalloc/kvzalloc_objs, which first attempts a contiguous allocation with
__GFP_NOWARN and then falls back to vmalloc for large sizes. Convert the
corresponding kfree calls to kvfree.
Both arrays are pure metadata lookup tables (arrays of pointers and zone
descriptors) accessed only via indexing, so they do not require physically
contiguous memory.
Reported-by: syzbot+924649752adf0d3ac9dd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/69adaba8.a00a0220.b130.0005.GAE@google.com/
Signed-off-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Yu Kuai <yukuai@fnnas.com>
Reviewed-by: Li Nan <linan122@huawei.com>
Link: https://lore.kernel.org/linux-raid/20260308234202.3118119-1-gourry@gourry.net/
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
erofs_init_device() only reads blocks_lo and uniaddr_lo from the
on-disk device slot, ignoring blocks_hi and uniaddr_hi that were
introduced alongside the 48-bit block addressing feature.
For the primary device (dif0), erofs_read_superblock() already handles
this correctly by combining blocks_lo with blocks_hi when 48-bit
layout is enabled. But the same logic was not applied to extra
devices.
With a 48-bit EROFS image using extra devices whose uniaddr or blocks
exceed 32-bit range, the truncated values cause erofs_map_dev() to
compute wrong physical addresses, leading to silent data corruption.
Fix this by reading blocks_hi and uniaddr_hi in erofs_init_device()
when 48-bit layout is enabled, consistent with the primary device
handling. Also fix the erofs_deviceslot on-disk definition where
blocks_hi was incorrectly declared as __le32 instead of __le16.
Fixes: 61ba89b579 ("erofs: add 48-bit block addressing on-disk support")
Suggested-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
DRBD used a custom mechanism to mark netlink attributes as "mandatory":
bit 14 of nla_type was repurposed as DRBD_GENLA_F_MANDATORY. Attributes
sent from userspace that had this bit present and that were unknown
to the kernel would lead to an error.
Since commit ef6243acb4 ("genetlink: optionally validate strictly/dumps"),
the generic netlink layer rejects unknown top-level attributes when
strict validation is enabled. DRBD never opted out of strict
validation, so unknown top-level attributes are already rejected by
the netlink core.
The mandatory flag mechanism was required for nested attributes, because
these are parsed liberally, silently dropping attributes unknown to the
kernel.
This prepares for the move to a new YNL-based family, which will use the
now-default strict parsing.
The current family is not expected to gain any new attributes, which
makes this change safe.
Old userspace that still sets bit 14 is unaffected: nla_type()
strips it before __nla_validate_parse() performs attribute validation,
so the bit never reaches DRBD.
Remove all references to the mandatory flag in DRBD.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://patch.msgid.link/20260403132953.2248751-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the upcoming ConnectX-10 NVLink-C2C device ID to the table of
supported PCI device IDs.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260403091756.139583-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: support MSG_EOR and small cleanups
This series contains various unrelated patches:
- Patches 1 & 2: support MSG_EOR instead of ignoring it.
- Patch 3: avoid duplicated code in TCP and MPTCP by using a new helper.
- Patch 4: adapt test to reproduce bug and increase code coverage.
====================
Link: https://patch.msgid.link/20260403-net-next-mptcp-msg_eor-misc-v1-0-b0b33bea3fed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In this "delete re-add signal" MPTCP Join subtest, the endpoint linked
to the initial subflow is removed, but readded once with different ID.
It appears that there was an issue when reusing the same ID, recently
fixed by commit d191101dee ("mptcp: pm: in-kernel: always set ID as
avail when rm endp"). The test then now reuses the same ID the first
time, but continue to use another one (88) the second time.
This should then cover more cases.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/615
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260403-net-next-mptcp-msg_eor-misc-v1-5-b0b33bea3fed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out a new helper tcp_recv_should_stop() from tcp_recvmsg_locked()
and tcp_splice_read() to check whether to stop receiving. And use this
helper in mptcp_recvmsg() and mptcp_splice_read() to reduce redundant code.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260403-net-next-mptcp-msg_eor-misc-v1-3-b0b33bea3fed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend MPTCP's sendmsg handling to recognize and honor the MSG_EOR flag,
which marks the end of a record for application-level message boundaries.
Data fragments tagged with MSG_EOR are explicitly marked in the
mptcp_data_frag structure and skb context to prevent unintended
coalescing with subsequent data chunks. This ensures the intent of
applications using MSG_EOR is preserved across MPTCP subflows,
maintaining consistent message segmentation behavior.
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260403-net-next-mptcp-msg_eor-misc-v1-2-b0b33bea3fed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'overhead' in struct mptcp_data_frag can safely use u8, as it
represents 'alignment + sizeof(mptcp_data_frag)'. With a maximum
alignment of 7('ALIGN(1, sizeof(long)) - 1'), the overhead is at most
47, well below U8_MAX and validated with BUILD_BUG_ON().
This patch also adds a field named 'unused' for further extensions.
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260403-net-next-mptcp-msg_eor-misc-v1-1-b0b33bea3fed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each object file contains information about which module it gets linked
into, so linking the same file into multiple modules now causes a warning:
scripts/Makefile.build:254: drivers/net/ethernet/freescale/dpaa2/Makefile: dpaa2-mac.o is added to multiple modules: fsl-dpaa2-eth fsl-dpaa2-switch
scripts/Makefile.build:254: drivers/net/ethernet/freescale/dpaa2/Makefile: dpmac.o is added to multiple modules: fsl-dpaa2-eth fsl-dpaa2-switch
Change the way that dpaa2 is built by moving the two common files into a
separate module with exported symbols instead.
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260402184726.3746487-3-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are six variants of the cpsw driver, sharing various parts of
the code: davinci-emac, cpsw, cpsw-switchdev, netcp, netcp_ethss and
am65-cpsw-nuss.
I noticed that this means some files can be linked into more than
one loadable module, or even part of vmlinux but also linked into
a loadable module, both of which mess up assumptions of the build
system, and causes warnings:
scripts/Makefile.build:279: cpsw_ale.o is added to multiple modules: ti-am65-cpsw-nuss ti_cpsw ti_cpsw_new
scripts/Makefile.build:279: cpsw_priv.o is added to multiple modules: ti_cpsw ti_cpsw_new
scripts/Makefile.build:279: cpsw_sl.o is added to multiple modules: ti-am65-cpsw-nuss ti_cpsw ti_cpsw_new
scripts/Makefile.build:279: cpsw_ethtool.o is added to multiple modules: ti_cpsw ti_cpsw_new
scripts/Makefile.build:279: davinci_cpdma.o is added to multiple modules: ti_cpsw ti_cpsw_new ti_davinci_emac
Change this back to having separate modules for each portion that
can be linked standalone, exporting symbols as needed:
- ti-cpsw-common.ko now contains both cpsw-common.o and
davinci_cpdma.o as they are always used together
- ti-cpsw-priv.ko contains cpsw_priv.o, cpsw_sl.o and cpsw_ethtool.o,
which are the core of the cpsw and cpsw-new drivers.
- ti-cpsw-sl.ko contains the cpsw-sl.o object and is used on
ti-am65-cpsw-nuss.ko in addition to the two other cpsw variants.
- ti-cpsw-ale.o is the one standalone module that is used by all
except davinci_emac.
Each of these will be built-in if any of its users are built-in, otherwise
it's a loadable module if there is at least one module using it. I did
not bring back the separate Kconfig symbols for this, but just handle
it using Makefile logic.
Note: ideally this is something that Kbuild complains about, but usually
we just notice when something using THIS_MODULE misbehaves in a way that
a user notices.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Link: https://lore.kernel.org/lkml/20240417084400.3034104-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260402184726.3746487-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While looking at the glob symbols shared between the cpsw drivers,
I noticed that soft_reset() is the only one that is missing a proper
namespace prefix, and will pollute the kernel namespace, so rename
it to be consistent with the other symbols.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260402184726.3746487-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The entire git history for this driver looks like tree-wide
and automated cleanups. There's even more coming now with
AI, so let's try to delete it instead.
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20260403220501.2263835-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PN557 uses the same hardware as the PN553 but ships with
firmware compliant with NCI 2.0.
Document PN557 as a compatible device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260403-oneplus-nfc-v3-1-fbdce57d63c1@ixit.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SKB_SMALL_HEAD_CACHE_SIZE is intentionally set to a non-power-of-2
value (e.g. 704 on x86_64) to avoid collisions with generic kmalloc
bucket sizes. This ensures that skb_kfree_head() can reliably use
skb_end_offset to distinguish skb heads allocated from
skb_small_head_cache vs. generic kmalloc caches.
However, when KFENCE is enabled, kfence_ksize() returns the exact
requested allocation size instead of the slab bucket size. If a caller
(e.g. bpf_test_init) allocates skb head data via kzalloc() and the
requested size happens to equal SKB_SMALL_HEAD_CACHE_SIZE, then
slab_build_skb() -> ksize() returns that exact value. After subtracting
skb_shared_info overhead, skb_end_offset ends up matching
SKB_SMALL_HEAD_HEADROOM, causing skb_kfree_head() to incorrectly free
the object to skb_small_head_cache instead of back to the original
kmalloc cache, resulting in a slab cross-cache free:
kmem_cache_free(skbuff_small_head): Wrong slab cache. Expected
skbuff_small_head but got kmalloc-1k
Fix this by always calling kfree(head) in skb_kfree_head(). This keeps
the free path generic and avoids allocator-specific misclassification
for KFENCE objects.
Fixes: bf9f1baa27 ("net: add dedicated kmem_cache for typical/small skb->head")
Reported-by: Antonius <antonius@bluedragonsec.com>
Closes: https://lore.kernel.org/netdev/CAK8a0jxC5L5N7hq-DT2_NhUyjBxrPocoiDazzsBk4TGgT1r4-A@mail.gmail.com/
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260403014517.142550-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When send() or recv() returns -1 with errno == EINTR, the code skips
the break but still adds the return value to nwritten/nread, making it
decrease by 1. This leads to wrong buffer offsets and wrong bytes count.
Fix it by explicitly continuing the loop on EINTR, so the return value
is only added when it is positive.
Fixes: a8ed71a27e ("vsock/test: add recv_buf() utility function")
Fixes: 12329bd51f ("vsock/test: add send_buf() utility function")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20260403093251.30662-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maciej Fijalkowski says:
====================
xsk: tailroom reservation and MTU validation
here we fix a long-standing issue regarding multi-buffer scenario in ZC
mode - we have not been providing space at the end of the buffer where
multi-buffer XDP works on skb_shared_info. This has been brought to our
attention via [0].
Unaligned mode does not get any specific treatment, it is user's
responsibility to properly handle XSK addresses in queues.
With adjustments included here in this set against xskxceiver I have
been able to pass the full test suite on ice.
[0]: https://community.intel.com/t5/Ethernet-Products/X710-XDP-Packet-Corruption-Issue-DRV-MODE-Zero-Copy-Multi-Buffer/m-p/1724208
====================
Link: https://patch.msgid.link/20260402154958.562179-1-maciej.fijalkowski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we have changed how big user defined headroom in umem can be,
change the logic in testapp_stats_rx_dropped() so we pass updated
headroom validation in xdp_umem_reg() and still drop half of frames.
Test works on non-mbuf setup so __xsk_pool_get_rx_frame_size() that is
called on xsk_rcv_check() will not account skb_shared_info size. Taking
the tailroom size into account in test being fixed is needed as
xdp_umem_reg() defaults to respect it.
Reviewed-by: Björn Töpel <bjorn@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20260402154958.562179-9-maciej.fijalkowski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
