Document support for LEDs node in phy and add an example for it.
PHY LED will have to match led pattern and should be treated as a
generic led.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Switch LED for each port for MikroTik RB3011UiAS-RM.
MikroTik RB3011UiAS-RM is a 10 port device with 2 qca8337 switch chips
connected.
It was discovered that in the hardware design all 3 Switch LED trace of
the related port is connected to the same LED. This was discovered by
setting to 'always on' the related led in the switch regs and noticing
that all 3 LED for the specific port (for example for port 1) cause the
connected LED for port 1 to turn on. As an extra test we tried enabling
2 different LED for the port resulting in the LED turned off only if
every led in the reg was off.
Aside from this funny and strange hardware implementation, the device
itself have one green LED for each port, resulting in 10 green LED one
for each of the 10 supported port.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPQ8064 MikroTik RB3011UiAS-RM DT have currently unevaluted properties
in the 2 switch nodes. The bindings #address-cells and #size-cells are
redundant and cause warning for 'Unevaluated properties are not
allowed'.
Drop these bindings to mute these warning as they should not be there
from the start.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs definition example for qca8k Switch Family to describe how they
should be defined for a correct usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document support for LEDs node in ethernet-controller.
Ethernet Controller may support different LEDs that can be configured
for different operation like blinking on traffic event or port link.
Also add some Documentation to describe the difference of these nodes
compared to PHY LEDs, since ethernet-controller LEDs are controllable
by the ethernet controller regs and the possible intergated PHY doesn't
have control on them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at
the same rate, and the reset default is 84ms per blink, which is
around 12Hz.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a brightness function, so the LEDs can be controlled from
software using the standard Linux LED infrastructure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide stubs for devm_led_classdev_register_ext() and
led_init_default_state_get() so that LED drivers embedded within other
drivers such as PHYs and Ethernet switches still build when LEDS_CLASS
or NEW_LEDS are disabled. This also helps with Kconfig dependencies,
which are somewhat hairy for phylib and mdio and only get worse when
adding a dependency on LED_CLASS.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our use-case needs two AT ports available:
One for running a ppp daemon, and another one for management
This patch enables a second AT port on DATA1
Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Call Trace:
<TASK>
dump_stack_lvl
ctnetlink_dump_timeout
__ctnetlink_glue_build
ctnetlink_glue_build
__nfqnl_enqueue_packet
nf_queue
nf_hook_slow
ip_mc_output
? __pfx_ip_finish_output
ip_send_skb
? __pfx_dst_output
udp_send_skb
udp_sendmsg
? __pfx_ip_generic_getfrag
sock_sendmsg
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3c ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=IcG3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.4 merge window
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
thunderbolt: Make use of SI units from units.h
thunderbolt: Get rid of redundant 'else'
thunderbolt: Refactor DROM reading
thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset
Addresses the following warning when building sdk7786_defconfig:
arch/sh/drivers/pci/pcie-sh7786.c:34:22: warning: 'dma_pfn_offset' defined but not used [-Wunused-variable]
34 | static unsigned long dma_pfn_offset;
| ^~~~~~~~~~~~~~
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230419070934.422997-1-glaubitz@physik.fu-berlin.de
Unfortunately, the tester gave a weak feedback (working/non-working) for
this case. After the double confirmation, this change is not really required.
The standard code with alc269_fallback_pin_fixup_tbl should work on this
hardware.
Fixes: 5911d78fab ("ALSA: hda/realtek: Improve support for Dell Precision 3260")
Fixes: 5f4efc9dfc ("ALSA: hda/realtek: Fix support for Dell Precision 3260")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230419081121.304846-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware SDO has issue to fill txd for the moment, so fallback to
driver filling method.
Fixes: 98686cd216 (wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices)
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7663 efuse has 0x600 bytes instead of 0x400. Increase the size in order
to fix issues with incomplete calibration data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This enables HW offloading amsdu/de-amsdu support for 802.11s mesh
interface.
Co-developed-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to BSS_CHANGED_BASIC_RATES, this enables mcast rate
configuration through fixed rate tables.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Change-Id: Ifc305e8c7de9a7df4ad5f856e2097d721a886aaa
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Matthieu Baerts says:
====================
mptcp: fixes around listening sockets and the MPTCP worker
Christoph Paasch reported a couple of issues found by syzkaller and
linked to operations done by the MPTCP worker on (un)accepted sockets.
Fixing these issues was not obvious and rather complex but Paolo Abeni
nicely managed to propose these excellent patches that seem to satisfy
syzkaller.
Patch 1 partially reverts a recent fix but while still providing a
solution for the previous issue, it also prevents the MPTCP worker from
running concurrently with inet_csk_listen_stop(). A warning is then
avoided. The partially reverted patch has been introduced in v6.3-rc3,
backported up to v6.1 and fixing an issue visible from v5.18.
Patch 2 prevents the MPTCP worker to race with mptcp_accept() causing a
UaF when a fallback to TCP is done while in parallel, the socket is
being accepted by the userspace. This is also a fix of a previous fix
introduced in v6.3-rc3, backported up to v6.1 but here fixing an issue
that is in theory there from v5.7. There is no need to backport it up
to here as it looks like it is only visible later, around v5.18, see the
previous cover-letter linked to this original fix.
====================
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
This patch fixes a missing 8 byte for the header size calculation. The
ipv6_rpl_srh_size() is used to check a skb_pull() on skb->data which
points to skb_transport_header(). Currently we only check on the
calculated addresses fields using CmprI and CmprE fields, see:
https://www.rfc-editor.org/rfc/rfc6554#section-3
there is however a missing 8 byte inside the calculation which stands
for the fields before the addresses field. Those 8 bytes are represented
by sizeof(struct ipv6_rpl_sr_hdr) expression.
Fixes: 8610c7c6e3 ("net: ipv6: add support for rpl sr exthdr")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Reported-by: maxpl0it <maxpl0it@protonmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vmxnet3_rq_create() fails to allocate rq->data_ring.base due to page
allocation failure, subsequent call to vmxnet3_rq_rx_complete() can result in
NULL pointer dereference.
To fix this bug, check not only that rxDataRingUsed is true but also that
adapter->rxdataring_enabled is true before calling memcpy() in
vmxnet3_rq_rx_complete().
[1728352.477993] ethtool: page allocation failure: order:9, mode:0x6000c0(GFP_KERNEL), nodemask=(null),cpuset=/,mems_allowed=0
...
[1728352.478009] Call Trace:
[1728352.478028] dump_stack+0x41/0x60
[1728352.478035] warn_alloc.cold.120+0x7b/0x11b
[1728352.478038] ? _cond_resched+0x15/0x30
[1728352.478042] ? __alloc_pages_direct_compact+0x15f/0x170
[1728352.478043] __alloc_pages_slowpath+0xcd3/0xd10
[1728352.478047] __alloc_pages_nodemask+0x2e2/0x320
[1728352.478049] __dma_direct_alloc_pages.constprop.25+0x8a/0x120
[1728352.478053] dma_direct_alloc+0x5a/0x2a0
[1728352.478056] vmxnet3_rq_create.part.57+0x17c/0x1f0 [vmxnet3]
...
[1728352.478188] vmxnet3 0000:0b:00.0 ens192: rx data ring will be disabled
...
[1728352.515347] BUG: unable to handle kernel NULL pointer dereference at 0000000000000034
...
[1728352.515440] RIP: 0010:memcpy_orig+0x54/0x130
...
[1728352.515655] Call Trace:
[1728352.515665] <IRQ>
[1728352.515672] vmxnet3_rq_rx_complete+0x419/0xef0 [vmxnet3]
[1728352.515690] vmxnet3_poll_rx_only+0x31/0xa0 [vmxnet3]
...
Signed-off-by: Seiji Nishikawa <snishika@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
net/mlx5e: Extend XDP multi-buffer capabilities
This series extends the XDP multi-buffer support in the mlx5e driver.
Patchset breakdown:
- Infrastructural changes and preparations.
- Add XDP multi-buffer support for XDP redirect-in.
- Use TX MPWQE (multi-packet WQE) HW feature for non-linear
single-segmented XDP frames.
- Add XDP multi-buffer support for striding RQ.
In Striding RQ, we overcome the lack of headroom and tailroom between
the RQ strides by allocating a side page per packet and using it for the
xdp_buff descriptor. We structure the xdp_buff so that it contains
nothing in the linear part, and the whole packet resides in the
fragments.
Performance highlight:
Packet rate test, 64 bytes, 32 channels, MTU 9000 bytes.
CPU: Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz.
NIC: ConnectX-6 Dx, at 100 Gbps.
+----------+-------------+-------------+---------+
| Test | Legacy RQ | Striding RQ | Speedup |
+----------+-------------+-------------+---------+
| XDP_DROP | 101,615,544 | 117,191,020 | +15% |
+----------+-------------+-------------+---------+
| XDP_TX | 95,608,169 | 117,043,422 | +22% |
+----------+-------------+-------------+---------+
Series generated against net commit:
e61caf04b9 Merge branch 'page_pool-allow-caching-from-safely-localized-napi'
I'm submitting this directly as Saeed is traveling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add support for multi-buffer XDP handling in Striding RQ, which
is our default out-of-the-box RQ type. Before this series, loading such
an XDP program would fail, until you switch to the legacy RQ (by
unsetting the rx_striding_rq priv-flag).
To overcome the lack of headroom and tailroom between the strides, we
allocate a side page to be used for the descriptor (xdp_buff / skb) and
the linear part. When an XDP program is attached, we structure the
xdp_buff so that it contains no data in the linear part, and the whole
packet resides in the fragments.
In case of XDP_PASS, where an SKB still needs to be created, we copy up
to 256 bytes to its linear part, to match the current behavior, and
satisfy functions that assume finding the packet headers in the SKB
linear part (like eth_type_trans).
Performance testing:
Packet rate test, 64 bytes, 32 channels, MTU 9000 bytes.
CPU: Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz.
NIC: ConnectX-6 Dx, at 100 Gbps.
+----------+-------------+-------------+---------+
| Test | Legacy RQ | Striding RQ | Speedup |
+----------+-------------+-------------+---------+
| XDP_DROP | 101,615,544 | 117,191,020 | +15% |
+----------+-------------+-------------+---------+
| XDP_TX | 95,608,169 | 117,043,422 | +22% |
+----------+-------------+-------------+---------+
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting XDP multi-buffer in striding RQ, use
xdp_buff struct to describe the packet. Make its skb_shared_info collide
the one of the allocated SKB, then add the fragments using the xdp_buff
API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the function more generic. Let it get an additional frame_sz
parameter instead of deriving it from the RQ struct.
No functional change here, just a preparation for a downstream patch.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5e_add_skb_shared_info_frag(), a function dedicated for
adding a fragment into a struct skb_shared_info object.
Use it in the Legacy RQ flow. Similar usage will be added in a
downstream patch by the corresponding Striding RQ flow.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under a few restrictions, TX MPWQE feature can serve multiple TX packets
in a single TX descriptor. It requires each of the packets to have a
single scatter entry / segment.
Today we allow only linear frames to use this feature, although there's
no real problem with non-linear ones where the whole packet reside in
the first fragment.
Expand the XDP TX MPWQE feature support to include such frames. This is
in preparation for the downstream patch, in which we will generate such
non-linear frames.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption of non-zero linear length in the XDP xmit
function, used to serve both internal XDP_TX operations as well as
redirected-in requests.
Do not apply the MLX5E_XDP_MIN_INLINE check unless necessary.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx5e_rx_get_linear_stride_sz() returns PAGE_SIZE immediately
in case an XDP program is attached. The more accurate formula is
ALIGN(sz, PAGE_SIZE), to prevent two packets from residing on the same
page.
The assumption behind the current code is that sz <= PAGE_SIZE holds for
all cases with XDP program set.
This is true because it is being called from:
- 3 times from Striding RQ flows, in which XDP is not supported for such
large packets.
- 1 time from Legacy RQ flow, under the condition
mlx5e_rx_is_linear_skb().
No functional change here, just removing the implied assumption in
preparation for supporting XDP multi-buffer in Striding RQ.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mlx5e_xdp_allowed() so it gets the params structure with the
xdp_prog applied, rather than creating a local copy based on the current
params in priv.
This reduces the amount of memory on the stack, and acts on the exact
params instance that's about to be applied.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non-linear mem scheme of Striding RQ does not yet support XDP at this
point. Take the check where it belongs, inside the params validation
function mlx5e_params_validate_xdp().
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle multi-buffer XDP redirect-in requests coming through
mlx5e_xdp_xmit.
Extend struct mlx5e_xmit_data_frags with an additional dma_arr field, to
point to the fragments dma mapping, as they cannot be retrieved via the
page_pool_get_dma_addr() function.
Push a dma_addr xdpi instance per each fragment, and use them in the
completion flow to dma_unmap the frags.
Finally, remove the restriction in mlx5e_open_xdpsq, and set the flag in
xdp_features.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we fix the current wi->num_pkts abuse, as it was used to indicate
multiple xdpi entries in the xdpi_fifo.
Instead, reduce mlx5e_xdp_info to the size of a single field, making it
a union of unions. Per packet, use as many instances as needed to
provide the information needed at the time of completion.
The sequence of xdpi instances pushed is well defined, derived by the
xmit_mode.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not likely nor unlikely that the xdp buff has fragments, it
depends on the program loaded and size of the packet received.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce struct mlx5e_xmit_data_frags to be used for non-linear xmit
buffers. Let it include sinfo pointer.
Take one bit from the len field to indicate if the descriptor has
fragments and can be casted-up into the extended version.
Zero-init to make sure has_frags, and potentially future fields, are
zero when not explicitly assigned.
Another field will be added in a downstream patch to indicate and point
to dma addresses of the different frags, for redirect-in requests.
This simplifies the mlx5e_xmit_xdp_frame/mlx5e_xmit_xdp_frame_mpwqe
functions params.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move TX datapath struct from the generic en.h to the datapath txrx.h
header, where it belongs.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move struct mlx5e_xdp_info and enum mlx5e_xdp_xmit_mode from the generic
en.h to the XDP header, where they belong.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a net device is put administratively up, its 'IFF_UP' flag is set
(if not set already) and a 'NETDEV_UP' notification is emitted, which
causes the 8021q driver to add VLAN ID 0 on the device. The reverse
happens when a net device is put administratively down.
When changing the type of a bond to Ethernet, its 'IFF_UP' flag is
incorrectly cleared, resulting in the kernel skipping the above process
and VLAN ID 0 being leaked [1].
Fix by restoring the flag when changing the type to Ethernet, in a
similar fashion to the restoration of the 'IFF_SLAVE' flag.
The issue can be reproduced using the script in [2], with example out
before and after the fix in [3].
[1]
unreferenced object 0xffff888103479900 (size 256):
comm "ip", pid 329, jiffies 4294775225 (age 28.561s)
hex dump (first 32 bytes):
00 a0 0c 15 81 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff81a6051a>] kmalloc_trace+0x2a/0xe0
[<ffffffff8406426c>] vlan_vid_add+0x30c/0x790
[<ffffffff84068e21>] vlan_device_event+0x1491/0x21a0
[<ffffffff81440c8e>] notifier_call_chain+0xbe/0x1f0
[<ffffffff8372383a>] call_netdevice_notifiers_info+0xba/0x150
[<ffffffff837590f2>] __dev_notify_flags+0x132/0x2e0
[<ffffffff8375ad9f>] dev_change_flags+0x11f/0x180
[<ffffffff8379af36>] do_setlink+0xb96/0x4060
[<ffffffff837adf6a>] __rtnl_newlink+0xc0a/0x18a0
[<ffffffff837aec6c>] rtnl_newlink+0x6c/0xa0
[<ffffffff837ac64e>] rtnetlink_rcv_msg+0x43e/0xe00
[<ffffffff839a99e0>] netlink_rcv_skb+0x170/0x440
[<ffffffff839a738f>] netlink_unicast+0x53f/0x810
[<ffffffff839a7fcb>] netlink_sendmsg+0x96b/0xe90
[<ffffffff8369d12f>] ____sys_sendmsg+0x30f/0xa70
[<ffffffff836a6d7a>] ___sys_sendmsg+0x13a/0x1e0
unreferenced object 0xffff88810f6a83e0 (size 32):
comm "ip", pid 329, jiffies 4294775225 (age 28.561s)
hex dump (first 32 bytes):
a0 99 47 03 81 88 ff ff a0 99 47 03 81 88 ff ff ..G.......G.....
81 00 00 00 01 00 00 00 cc cc cc cc cc cc cc cc ................
backtrace:
[<ffffffff81a6051a>] kmalloc_trace+0x2a/0xe0
[<ffffffff84064369>] vlan_vid_add+0x409/0x790
[<ffffffff84068e21>] vlan_device_event+0x1491/0x21a0
[<ffffffff81440c8e>] notifier_call_chain+0xbe/0x1f0
[<ffffffff8372383a>] call_netdevice_notifiers_info+0xba/0x150
[<ffffffff837590f2>] __dev_notify_flags+0x132/0x2e0
[<ffffffff8375ad9f>] dev_change_flags+0x11f/0x180
[<ffffffff8379af36>] do_setlink+0xb96/0x4060
[<ffffffff837adf6a>] __rtnl_newlink+0xc0a/0x18a0
[<ffffffff837aec6c>] rtnl_newlink+0x6c/0xa0
[<ffffffff837ac64e>] rtnetlink_rcv_msg+0x43e/0xe00
[<ffffffff839a99e0>] netlink_rcv_skb+0x170/0x440
[<ffffffff839a738f>] netlink_unicast+0x53f/0x810
[<ffffffff839a7fcb>] netlink_sendmsg+0x96b/0xe90
[<ffffffff8369d12f>] ____sys_sendmsg+0x30f/0xa70
[<ffffffff836a6d7a>] ___sys_sendmsg+0x13a/0x1e0
[2]
ip link add name t-nlmon type nlmon
ip link add name t-dummy type dummy
ip link add name t-bond type bond mode active-backup
ip link set dev t-bond up
ip link set dev t-nlmon master t-bond
ip link set dev t-nlmon nomaster
ip link show dev t-bond
ip link set dev t-dummy master t-bond
ip link show dev t-bond
ip link del dev t-bond
ip link del dev t-dummy
ip link del dev t-nlmon
[3]
Before:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 46:57:39:a4:46:a2 brd ff:ff:ff:ff:ff:ff
After:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 66:48:7b:74:b6:8a brd ff:ff:ff:ff:ff:ff
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Fixes: 75c78500dd ("bonding: remap muticast addresses without using dev_close() and dev_open()")
Fixes: 9ec7eb60dc ("bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/netdev/78a8a03b-6070-3e6b-5042-f848dab16fb8@alu.unizg.hr/
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
