-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmLXs+kTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXRhhB/4oU+hdSITnF4SkX+bHa2+7YP/qq2CS
AT4/cc7WheYsCB/NFLLBQ9YuPJauw8Z7dTcOvWDX5vxfKzkYen9QaMOhkX67q4i4
yTk1j28ryh7SSMOmSoSlBgru/sqDGL0gc2d3K/DnABJcudrY4gOsFsHA24yPCoPS
XwRen/O+/zbumrZrn2vhcqpRKQFq7B4D5GXhFBKyi/VnPpd1z9vb7nR1RqBzg1Qr
xdW0oNewAwOv0w1VbZUWJWa2NlsIIdyhSX2hG4pa4GBUl9/KHtA9SMS4WSCcvUhP
PpRM2o7MTFKB0ViJqseNxty6f4Xin7B5tNshj9vpmchw5QBFRSN1v1g5
=0265
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.20-20220720' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 29 patches for net-next/master.
The first 6 patches target the slcan driver. Dan Carpenter contributes
a hardening patch, followed by 5 cleanup patches.
Biju Das contributes 5 patches to prepare the sja1000 driver to
support the Renesas RZ/N1 SJA1000 CAN controller.
Dario Binacchi's patch for the slcan driver fixes a sleep with held
spin lock.
Another patch by Dario Binacchi fixes a wrong comment in the c_can
driver.
Pavel Pisa updates the CTU CAN FD IP core registers.
Stephane Grosjean contributes 3 patches to the peak_usb driver for
cleanups and support of a new MCU.
The last 12 patches are by Vincent Mailhol, they fix and improve the
txerr and rxerr reporting in all CAN drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima says:
====================
sysctl: Fix data-races around ipv4_net_table (Round 4).
This series fixes data-races around 17 knobs after fib_multipath_use_neigh
in ipv4_net_table.
tcp_fack was skipped because it's obsolete and there's no readers.
So, round 5 will start with tcp_dsack, 2 rounds left for 27 knobs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_max_reordering, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: dca145ffaa ("tcp: allow for bigger reordering level")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_abort_on_overflow, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_rfc1337, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_stdurg, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_retrans_collapse, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 35089bb203 ("[TCP]: Add tcp_slow_start_after_idle sysctl.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_thin_linear_timeouts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 36e31b0af5 ("net: TCP thin linear timeouts")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_recovery, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 4f41b1c58a ("tcp: use RACK to detect losses")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_early_retrans, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: eed530b6c6 ("tcp: early retransmit")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading these knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_sack
- tcp_window_scaling
- tcp_timestamps
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_udp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 63a6fff353 ("net: Avoid receiving packets with an l3mdev on unbound UDP sockets")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_ip_prot_sock is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
Fixes: 4548b683b7 ("Introduce a sysctl that modifies the value of PROT_SOCK.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_hash_fields, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: ce5c9c20d3 ("ipv4: Add a sysctl to control multipath hash fields")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_hash_policy, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: bf4e0a3db9 ("net: ipv4: add support for ECMP hash policy choice")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fib_multipath_use_neigh, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: a6db4494d2 ("net: ipv4: Consider failed nexthops in multipath routes")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-07-20
1) Fix a policy refcount imbalance in xfrm_bundle_lookup.
From Hangyu Hua.
2) Fix some clang -Wformat warnings.
Justin Stitt
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During a subsystem reset the Topology-Change-Report is cleared.
Let's give userland the possibility to clear the MTCR in the case
of a subsystem reset.
To migrate the MTCR, we give userland the possibility to
query the MTCR state.
We indicate KVM support for the CPU topology facility with a new
KVM capability: KVM_CAP_S390_CPU_TOPOLOGY.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20220714194334.127812-1-pmorel@linux.ibm.com>
Link: https://lore.kernel.org/all/20220714194334.127812-1-pmorel@linux.ibm.com/
[frankja@linux.ibm.com: Simple conflict resolution in Documentation/virt/kvm/api.rst]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
We report a topology change to the guest for any CPU hotplug.
The reporting to the guest is done using the Multiprocessor
Topology-Change-Report (MTCR) bit of the utility entry in the guest's
SCA which will be cleared during the interpretation of PTF.
On every vCPU creation we set the MCTR bit to let the guest know the
next time it uses the PTF with command 2 instruction that the
topology changed and that it should use the STSI(15.1.x) instruction
to get the topology details.
STSI(15.1.x) gives information on the CPU configuration topology.
Let's accept the interception of STSI with the function code 15 and
let the userland part of the hypervisor handle it when userland
supports the CPU Topology facility.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20220714101824.101601-2-pmorel@linux.ibm.com
Message-Id: <20220714101824.101601-2-pmorel@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
We can check if SIIF is enabled by testing the sclp_info struct
instead of testing the sie control block eca variable as that
facility is always enabled if available.
Also let's cleanup all the ipte related struct member accesses
which currently happen by referencing the KVM struct via the
VCPU struct.
Making the KVM struct the parameter to the ipte_* functions
removes one level of indirection which makes the code more readable.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Link: https://lore.kernel.org/all/20220711084148.25017-2-pmorel@linux.ibm.com/
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
The reset-simple driver does not build on all architecuters as it requires
devm_ioremap_resource() which is only built when CONFIG_HAS_IOMEM is enabled
in the kenrel. Fix the following error by depending on CONFIG_HAS_IOMEM:
drivers/reset/reset-simple.o: in function `reset_simple_probe':
reset-simple.c:(.text+0x3aa): undefined reference to `devm_ioremap_resource'
Fixes: 18d1909be3 ("reset: allow building of reset simple driver if expert config selected")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220719085200.203688-1-ben.dooks@sifive.com
We should use of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220712095623.364287-1-windhl@126.com
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit c6f2a617a0 ("can: mcp251xfd: add support for mcp251863")
support for the mcp251863 was added. However it was not taken into
account that the auto detection of the chip model cannot distinguish
between mcp2518fd and mcp251863 and would lead to a warning message if
the firmware specifies a mcp251863.
Fix auto detection: If a mcp2518fd compatible chip is found, keep the
mcp251863 if specified by firmware, use mcp2518fd instead.
Link: https://lore.kernel.org/all/20220706064835.1848864-1-mkl@pengutronix.de
Fixes: c6f2a617a0 ("can: mcp251xfd: add support for mcp251863")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When running under OP-TEE, the L2 cache is configured by OP-TEE and the
sam platform code does not allow any modification yet. Setup a dummy
.write_sec() callback to avoid triggering exceptions when Linux tries
to modify the L2 cache configuration.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[claudiu.beznea: keep .init_early populated only for SAMA5D2, remove
sam_secure_init() from sama5d2_init() as it is also called in
sama5_secure_cache_init()]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220606145701.185552-3-clement.leger@bootlin.com
Add sam_linux_is_optee_available() which allows to know if OP-TEE is
available for Linux. This function is used by code which needs to
know if we running with OP-TEE available or not.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[claudiu.beznea: edit commit title and message, renamed
sam_linux_is_in_normal_world() into sam_linux_is_optee_available()]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220606145701.185552-2-clement.leger@bootlin.com
Vincent Mailhol says:
====================
can: error: set of fixes and improvement on txerr and rxerr reporting
This series is a collection of patches targeting the CAN error
counter. The series is split in three blocks (with small relation to
each other).
Several drivers uses the data[6] and data[7] fields (both of type u8)
of the CAN error frame to report those values. However, the maximum
size an u8 can hold is 255 and the error counter can exceed this value
if bus-off status occurs. As such, the first nine patches of this
series make sure that no drivers try to report txerr or rxerr through
the CAN error frame when bus-off status is reached.
can_frame::data[5..7] are defined as being "controller
specific". Controller specific behaviors are not something desirable
(portability issue...) The tenth patch of this series specifies how
can_frame::data[5..7] should be use and remove any "controller
specific" freedom. The eleventh patch adds a flag to notify though
can_frame::can_id that data[6..7] were populated (in order to be
consistent with other fields).
Finally, the twelfth and last patch add three macro values to specify
the different error counter threshold with so far was hard-coded as
magic numbers in the drivers.
N.B.:
* patches 1 to 10 are for net (stable).
* patches 11 and 12 are for net-next (but depends on patches 1 to 10).
** Changelog **
v1 -> v2: https://lore.kernel.org/all/20220712153157.83847-1-mailhol.vincent@wanadoo.fr
* Fix typo in patch #10: data[7] of CAN error frames is for the RX
error counter, not the TX one (this is litteraly a one byte
change).
====================
As discussed take the whole series via can-next -> net-next.
Link: https://lore.kernel.org/all/20220719143550.3681-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
libsha1 can be a module, so it needs a MODULE_LICENSE.
Fixes: ec8f7f4821 ("crypto: lib - make the sha1 library optional")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, drivers are using magic numbers to derive the CAN error
states from the error counter. Add three macro declarations to
remediate this.
For reference, the error-active, error-passive and bus-off are defined
in ISO 11898, section 12.1.4.2 "Error counting". Although ISO 11898
does not define error-warning state, this extra value is also commonly
used and is thus also added.
Link: https://lore.kernel.org/all/20220719143550.3681-13-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a dedicated flag in uapi/linux/can/error.h to notify the userland
that fields data[6] and data[7] of the CAN error frame were
respectively populated with the tx and rx error counters.
For all driver tree-wide, set up this flags whenever needed.
Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently, data[5..7] of struct can_frame, when used as a CAN error
frame, are defined as being "controller specific". Device specific
behaviours are problematic because it prevents someone from writing
code which is portable between devices.
As a matter of fact, data[5] is never used, data[6] is always used to
report TX error counter and data[7] is always used to report RX error
counter. can-utils also relies on this.
This patch updates the comment in the uapi header to specify that
data[5] is reserved (and thus should not be used) and that data[6..7]
are used for error counters.
Fixes: 0d66548a10 ("[CAN]: Add PF_CAN core module")
Link: https://lore.kernel.org/all/20220719143550.3681-11-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220719143550.3681-10-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 7259124eac ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Link: https://lore.kernel.org/all/20220719143550.3681-9-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Link: https://lore.kernel.org/all/20220719143550.3681-8-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Link: https://lore.kernel.org/all/20220719143550.3681-7-mailhol.vincent@wanadoo.fr
CC: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 215db1856e ("can: sja1000: Consolidate and unify state change handling")
Link: https://lore.kernel.org/all/20220719143550.3681-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0c78ab76a0 ("pch_can: Add setting TEC/REC statistics processing")
Link: https://lore.kernel.org/all/20220719143550.3681-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In dcss_dev_create() and dcss_dev_destroy(), we should call of_node_put()
in fail path or before the dcss's destroy as of_graph_get_port_by_id() has
increased the refcount.
Fixes: 9021c317b7 ("drm/imx: Add initial support for DCSS on iMX8MQ")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220714081337.374761-1-windhl@126.com
I recently switched to my Alibaba email address. So add aliases for my
previous email addresses.
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clock controller supports an optional clock gating register. This is
necessary to expose the USB device clock, for example. Add it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220707132500.1708020-1-michael@walle.cc
With GCC 12 allmodconfig prom_init fails to build:
Error: External symbol 'memset' referenced from prom_init.c
make[2]: *** [arch/powerpc/kernel/Makefile:204: arch/powerpc/kernel/prom_init_check] Error 1
The allmodconfig build enables KASAN, so all calls to memset in
prom_init should be converted to __memset by the #ifdefs in
asm/string.h, because prom_init must use the non-KASAN instrumented
versions.
The build failure happens because there's a call to memset that hasn't
been caught by the pre-processor and converted to __memset. Typically
that's because it's a memset generated by the compiler itself, and that
is the case here.
With GCC 12, allmodconfig enables CONFIG_INIT_STACK_ALL_PATTERN, which
causes the compiler to emit memset calls to initialise on-stack
variables with a pattern.
Because prom_init is non-user-facing boot-time only code, as a
workaround just disable stack variable initialisation to unbreak the
build.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220718134418.354114-1-mpe@ellerman.id.au
The hartid can be a 64bit value on RV64 platforms. This series updates
the code so that 64bit hartid can be supported on RV64 platforms.
* 'riscv-64bit_hartid' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux.git:
riscv/efi_stub: Add 64bit boot-hartid support on RV64
riscv: cpu: Add 64bit hartid support on RV64
riscv: smp: Add 64bit hartid support on RV64
riscv: spinwait: Fix hartid variable type
riscv: cpu_ops_sbi: Add 64bit hartid support on RV64
This patch re-introduces support for GuC v69 in parallel to v70. As this
is a quick fix, v69 has been re-introduced as the single "fallback" guc
version in case v70 is not available on disk and only for platforms that
are out of force_probe and require the GuC by default. All v69 specific
code has been labeled as such for easy identification, and the same was
done for all v70 functions for which there is a separate v69 version,
to avoid accidentally calling the wrong version via the unlabeled name.
When the fallback mode kicks in, a drm_notice message is printed in
dmesg to inform the user of the required update. The existing
logging of the fetch function has also been updated so that we no
longer complain immediately if we can't find a fw and we only throw an
error if the fetch of both the base and fallback blobs fails.
The plan is to follow this up with a more complex rework to allow for
multiple different GuC versions to be supported at the same time.
v2: reduce the fallback to platform that require it, switch to
firmware_request_nowarn(), improve logs.
Fixes: 2584b3549f ("drm/i915/guc: Update to GuC version 70.1.1")
Link: https://lists.freedesktop.org/archives/intel-gfx/2022-July/301640.html
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220718230732.1409641-1-daniele.ceraolospurio@intel.com
(cherry picked from commit 774ce1510e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In GuC submission mode the EU priority must be updated by the GuC rather
than the driver as the GuC owns the programming of the context descriptor.
Given that the GuC code uses the GuC priorities, we can't use a generic
function using i915 priorities for both execlists and GuC submission.
The existing function has therefore been pushed to the execlists
back-end while a new one has been added for GuC.
v2: correctly use the GuC prio.
Cc: John Harrison <john.c.harrison@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Aravind Iddamsetty <aravind.iddamsetty@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220504234636.2119794-1-daniele.ceraolospurio@intel.com
(cherry picked from commit a5c89f7c43)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drivers/platform/chrome/cros_kbd_led_backlight.c got a new build warning
when using the randconfig in [1]:
>>> warning: unused variable 'keyboard_led_drvdata_ec_pwm'
The warning happens when CONFIG_CROS_EC is set but CONFIG_OF is not set.
Reproduce:
- mkdir build_dir
- wget [1] -O build_dir/.config
- COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 \
O=build_dir ARCH=s390 SHELL=/bin/bash drivers/platform/chrome/
Fix the warning by using __maybe_unused. Also use IS_ENABLED() because
CROS_EC is a tristate.
[1]: https://download.01.org/0day-ci/archive/20220717/202207170538.MR39dw8m-lkp@intel.com/config
Fixes: 40f5814374 ("platform/chrome: cros_kbd_led_backlight: support EC PWM backend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20220718105047.2356542-1-tzungbi@kernel.org