Some extreme test environment may keep IC temperature very low or very high
during system boot stage. For stability concern, we add thermal voltage
compenstation if needed no matter svs bank phase is in init02 or mon mode.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230202124104.16504-4-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
clang with W=1 reports
net/mac80211/rc80211_minstrel_ht.c:1711:6: error: variable
'n_supported' set but not used [-Werror,-Wunused-but-set-variable]
int n_supported = 0;
^
This variable is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230325132610.1334820-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid potential data corruption issues caused by uninitialized driver
private data structures.
Reported-by: Brian Coverstone <brian@mainsequence.net>
Fixes: 6a9d1b91f3 ("mac80211: add pre-RCU-sync sta removal driver operation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324120924.38412-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust the network header to point at the correct payload offset
Fixes: 986e43b19a ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230324120924.38412-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.
Reported-by: Thomas Hühn <thomas.huehn@hs-nordhausen.de>
Reported-by: Nick Hainke <vincent@systemli.org>
Fixes: 986e43b19a ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230326151709.17743-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a 64-bit division in iwl_mvm_get_crosstimestamp_fw(), which
results in a link failure when building 32-bit architectures with clang:
ld.lld: error: undefined symbol: __udivdi3
>>> referenced by ptp.c
>>> drivers/net/wireless/intel/iwlwifi/mvm/ptp.o:(iwl_mvm_phc_get_crosstimestamp) in archive vmlinux.a
GCC has optimizations for division by a constant that clang does not
implement, so this issue is not visible when building with GCC.
Use the 64-bit division helper div_u64(), which takes a u64 dividend and
u32 divisor, which matches this situation and prevents the emission of a
libcall for the division.
Fixes: 21fb8da6eb ("wifi: iwlwifi: mvm: read synced time from firmware if supported")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://github.com/ClangBuiltLinux/linux/issues/1826
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Link: https://lore.kernel.org/6423173a.620a0220.3d5cc.6358@mx.google.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rx->sta->amsdu_mesh_control is being passed to ieee80211_amsdu_to_8023s
without checking rx->sta. Since it doesn't make sense to accept A-MSDU
packets without a sta, simply add a check earlier.
Fixes: 6e4c0d0460 ("wifi: mac80211: add a workaround for receiving non-standard mesh A-MSDU")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230330090001.60750-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic in acpi_is_processor_usable() requires the online capable
bit be set for hotpluggable CPUs. The online capable bit has been
introduced in ACPI 6.3.
However, for ACPI revisions < 6.3 which do not support that bit, CPUs
should be reported as usable, not the other way around.
Reverse the check.
[ bp: Rewrite commit message. ]
Fixes: e2869bd7af ("x86/acpi/boot: Do not register processors that cannot be onlined for x2APIC")
Suggested-by: Miguel Luis <miguel.luis@oracle.com>
Suggested-by: Boris Ostrovsky <boris.ovstrosky@oracle.com>
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: David R <david@unsolicited.net>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230327191026.3454-2-eric.devolder@oracle.com
ACPI 6.3 introduced the online capable bit, and also introduced MADT
version 5.
Latter was used to distinguish whether the offset storing online capable
could be used. However ACPI 6.2b has MADT version "45" which is for
an errata version of the ACPI 6.2 spec. This means that the Linux code
for detecting availability of MADT will mistakenly flag ACPI 6.2b as
supporting online capable which is inaccurate as it's an ACPI 6.3 feature.
Instead use the FADT major and minor revision fields to distinguish this.
[ bp: Massage. ]
Fixes: aa06e20f1b ("x86/ACPI: Don't add CPUs that are not online capable")
Reported-by: Eric DeVolder <eric.devolder@oracle.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/943d2445-84df-d939-f578-5d8240d342cc@unsolicited.net
Arseniy Krasnov says:
====================
fix header length on skb merging
this patchset fixes appending newly arrived skbuff to the last skbuff of
the socket's queue during rx path. Problem fires when we are trying to
append data to skbuff which was already processed in dequeue callback
at least once. Dequeue callback calls function 'skb_pull()' which changes
'skb->len'. In current implementation 'skb->len' is used to update length
in header of last skbuff after new data was copied to it. This is bug,
because value in header is used to calculate 'rx_bytes'/'fwd_cnt' and
thus must be constant during skbuff lifetime. Here is example, we have
two skbuffs: skb0 with length 10 and skb1 with length 4.
1) skb0 arrives, hdr->len == skb->len == 10, rx_bytes == 10
2) Read 3 bytes from skb0, skb->len == 7, hdr->len == 10, rx_bytes == 10
3) skb1 arrives, hdr->len == skb->len == 4, rx_bytes == 14
4) Append skb1 to skb0, skb0 now has skb->len == 11, hdr->len == 11.
But value of 11 in header is invalid.
5) Read whole skb0, update rx_bytes by 11 from skb0's header.
6) At this moment rx_bytes == 3, but socket's queue is empty.
This bug starts to fire since:
commit
0777061657 ("virtio/vsock: don't use skbuff state to account credit")
In fact, it presents before, but didn't triggered due to a little bit
buggy implementation of credit calculation logic. So i'll use Fixes tag
for it.
I really forgot about this branch in rx path when implemented patch
0777061657.
This patchset contains 3 patches:
1) Fix itself.
2) Patch with WARN_ONCE() to catch such problems in future.
3) Patch with test which triggers skb appending logic. It looks like
simple test with several 'send()' and 'recv()', but it checks, that
skbuff appending works ok.
====================
Link: https://lore.kernel.org/r/0683cc6e-5130-484c-1105-ef2eb792d355@sberdevices.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds test which checks case when data of newly received skbuff is
appended to the last skbuff in the socket's queue. It looks like simple
test with 'send()' and 'recv()', but internally it triggers logic which
appends one received skbuff to another. Test checks that this feature
works correctly.
This test is actual only for virtio transport.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds WARN_ONCE() and return from stream dequeue callback when
socket's queue is empty, but 'rx_bytes' still non-zero. This allows
the detection of potential bugs due to packet merging (see previous
patch).
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This fixes appending newly arrived skbuff to the last skbuff of the
socket's queue. Problem fires when we are trying to append data to skbuff
which was already processed in dequeue callback at least once. Dequeue
callback calls function 'skb_pull()' which changes 'skb->len'. In current
implementation 'skb->len' is used to update length in header of the last
skbuff after new data was copied to it. This is bug, because value in
header is used to calculate 'rx_bytes'/'fwd_cnt' and thus must be not
be changed during skbuff's lifetime.
Bug starts to fire since:
commit 0777061657
("virtio/vsock: don't use skbuff state to account credit")
It presents before, but didn't triggered due to a little bit buggy
implementation of credit calculation logic. So use Fixes tag for it.
Fixes: 0777061657 ("virtio/vsock: don't use skbuff state to account credit")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The mISDN_class_release() is not needed at all, as the class structure
is static, and it does not actually do anything either, so it is safe to
remove as struct class does not require a release callback.
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230329060127.2688492-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-20-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-19-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a GPU node for MT8186 SoC but keep it disabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-18-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the Mali-G57 found on this platform with the open-source
Panfrost driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-17-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add GPU support through panfrost for the Mali-G57 GPU on MT8195
with its OPP table but keep it in disabled state.
This is expected to be enabled only on boards which make use of
the GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-16-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Similarly to what can be seen in MT8192, on MT8195 the mfg_core_tmp
clock is a mux used to switch between different "safe" (and slower)
clock sources for the GPU: this is used during MFGPLL reconfiguration
and eventually during idling at very low frequencies.
This clock getting turned off means that the GPU will occasionally be
unclocked, producing obvious consequences such as system crash or
unpredictable behavior: assigning it to the top level MFG power domain
will make sure that this stays on at all times during any operation on
the MFG domain (only GPU-related transactions).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-15-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the GPU with its power supplies described.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
[wenst@: patch split out from MT8192 GPU node patch]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: Minor commit title fix]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-14-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as VSRAM_OTHER is used to power the
GPU SRAM, and they have a strict voltage output relation to satisfy in
order to ensure GPU stable operation.
While at it, also add voltage constraint overrides for the GPU SRAM
regulator "mt6359_vsram_others" so that we stay in a safe range of
0.75-0.80V.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-13-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8192 SoC specifies a maximum voltage for the GPU's digital supply
of 0.88V and the GPU OPPs are declaring a maximum voltage of 0.80V.
In order to keep the GPU voltage in the safe range, change the maximum
voltage for mt6315@7's vbuck1 to 0.80V as sending, for any mistake,
1.193V would be catastrophic.
Fixes: 3183cb62b0 ("arm64: dts: mediatek: asurada: Add SPMI regulators")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-12-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a phandle to the MT8192_POWER_DOMAIN_MFG1 power domain and
assign the GPU VSRAM supply to this in mt8192-asurada: this allows to
keep the sram powered up while the GPU is used.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-11-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mfg0 power domain encompasses the whole GPU and its surrounding
glue logic. This power domain has a separate power rail.
Add its power supply for Asurada.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[wenst@chromium.org: fix subject prefix and add commit message]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: Reordered commits to address DVFS stability issues]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mfg_ref_sel clock is a mux used to switch between different "safe"
(and slower) clock sources for the GPU: this is used during MFGPLL
reconfiguration and eventually during idling at very low frequencies.
This clock getting turned off means that the GPU will occasionally be
unclocked, producing obvious consequences such as system crash or
unpredictable behavior: assigning it to the top level MFG power domain
will make sure that this stays on at all times during any operation on
the MFG domain (only GPU-related transactions).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MediaTek MT8192 includes a Mali-G57 GPU supported in Panfrost. Add
the GPU node to the device tree to enable 3D acceleration.
The GPU node is disabled by default. It should be enabled by board with
its power supplies correctly assigned.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
[nfraprado: removed sram supply, tweaked opp node name, adjusted commit message]
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[wenst@: disable GPU by default; adjusted prefix; split out board change]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: cosmetic fixes]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use the new GPU related compatible to finally enable GPU DVFS on
the MT8183 SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This was done to keep a strict relation between VSRAM and VGPU, but
it never worked: now we're doing it transparently with the new
mediatek-regulator-coupler driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Marco's NXP email is no longer valid.
Marco told me offline that he has no interest to be listed as the
maintainer contact for this binding, so add my contact.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329201150.741106-1-festevam@gmail.com
We've aligned setgid behavior over multiple kernel releases. The details
can be found in the following two merge messages:
cf619f8919 ("Merge tag 'fs.ovl.setgid.v6.2')
426b4ca2d6 ("Merge tag 'fs.setgid.v6.0')
Consistent setgid stripping behavior is now encapsulated in the
setattr_should_drop_sgid() helper which is used by all filesystems that
strip setgid bits outside of vfs proper. Switch nfs to rely on this
helper as well. Without this patch the setgid stripping tests in
xfstests will fail.
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Message-Id: <20230313-fs-nfs-setgid-v2-1-9a59f436cfc0@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Like the other calls in this function virt_to_page() expects
a pointer, not an integer.
However since many architectures implement virt_to_pfn() as
a macro, this function becomes polymorphic and accepts both a
(unsigned long) and a (void *).
Fix this up with an explicit cast.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Implements use of per-cpu irq for optee asynchronous notification.
Existing optee async notif implementation allows OP-TEE world to
raise an interrupt on which Linux optee driver will query some pending
events. This change allows the signaling interrupt to be a per-cpu
interrupt as with Arm GIC PPIs. Using a PPI instead of an SPI is useful
when no GIC lines are provisioned in the chip design and there are spare
PPI lines.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Marc Zyngier <maz@kernel.org>
Co-developed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
[JW: fixing a spell error in @notif_pcpu_wq description]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Explicit in optee firmware device tree bindings that the interrupt
used by optee driver for async notification can be a peripheral
interrupt or a per-cpu interrupt.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Currently, with VHE, KVM enables the EL0 event counting for the
guest on vcpu_load() or KVM enables it as a part of the PMU
register emulation process, when needed. However, in the migration
case (with VHE), the same handling is lacking, as vPMU register
values that were restored by userspace haven't been propagated yet
(the PMU events haven't been created) at the vcpu load-time on the
first KVM_RUN (kvm_vcpu_pmu_restore_guest() called from vcpu_load()
on the first KVM_RUN won't do anything as events_{guest,host} of
kvm_pmu_events are still zero).
So, with VHE, enable the guest's EL0 event counting on the first
KVM_RUN (after the migration) when needed. More specifically,
have kvm_pmu_handle_pmcr() call kvm_vcpu_pmu_restore_guest()
so that kvm_pmu_handle_pmcr() on the first KVM_RUN can take
care of it.
Fixes: d0c94c4979 ("KVM: arm64: Restore PMU configuration on first run")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230329023944.2488484-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Dragos Tatulea says:
====================
net/mlx5e: RX, Drop page_cache and fully use page_pool
For page allocation on the rx path, the mlx5e driver has been using an
internal page cache in tandem with the page pool. The internal page
cache uses a queue for page recycling which has the issue of head of
queue blocking.
This patch series drops the internal page_cache altogether and uses the
page_pool to implement everything that was done by the page_cache
before:
* Let the page_pool handle dma mapping and unmapping.
* Use fragmented pages with fragment counter instead of tracking via
page ref.
* Enable skb recycling.
The patch series has the following effects on the rx path:
* Improved performance for the cases when there was low page recycling
due to head of queue blocking in the internal page_cache. The test
for this was running a single iperf TCP stream to a rx queue
which is bound on the same cpu as the application.
|-------------+--------+--------+------+---------|
| rq type | before | after | unit | diff |
|-------------+--------+--------+------+---------|
| striding rq | 30.1 | 31.4 | Gbps | 4.14 % |
| legacy rq | 30.2 | 33.0 | Gbps | 8.48 % |
|-------------+--------+--------+------+---------|
* Small XDP performance degradation. The test was is XDP drop
program running on a single rx queue with small packets incoming
it looks like this:
|-------------+----------+----------+------+---------|
| rq type | before | after | unit | diff |
|-------------+----------+----------+------+---------|
| striding rq | 19725449 | 18544617 | pps | -6.37 % |
| legacy rq | 19879931 | 18631841 | pps | -6.70 % |
|-------------+----------+----------+------+---------|
This will be handled in a different patch series by adding support for
multi-packet per page.
* For other cases the performance is roughly the same.
The above numbers were obtained on the following system:
24 core Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz
32 GB RAM
ConnectX-7 single port
The breakdown on the patch series is the following:
* Preparations for introducing the mlx5e_frag_page struct.
* Delete the mlx5e_page_cache struct.
* Enable dma mapping from page_pool.
* Enable skb recycling and fragment counting.
* Do deferred release of pages (just before alloc) to ensure better
page_pool cache utilization.
====================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmQjUY8ACgkQSD+KveBX
+j6tVAf/QHCbKgt9c2Q5EpFch2e4x3A/HfE7DbxTancIj0cc1bH98xd4wO574aE4
PCJ/aJ+9zTLvTUgUnKDaiqonfmcsF7v6d/ltoLW1PTNnPqdsjsXpVy76dnL81SWy
u/g7h68cfeMdMjAAoewyVv+k7GeTIZCsIdvik3dWGFQ67IpE1k5dLbO13YBNW/5m
Cm39RzD55tjgxS8GHdyFYAV4MwgHy+pdhTYR9LGzH80hfd02KqsCO38u1NIShuez
1rwjRF213Qdln20bMNSNiXG36JUV65mo+Q/XHKOEjB0qNKRcF5bzZovqHzP+R7QZ
qhhhfce8c63UWpcXADP6k6qevW8+UA==
=8F1t
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-03-28
Dragos Tatulea says:
====================
net/mlx5e: RX, Drop page_cache and fully use page_pool
For page allocation on the rx path, the mlx5e driver has been using an
internal page cache in tandem with the page pool. The internal page
cache uses a queue for page recycling which has the issue of head of
queue blocking.
This patch series drops the internal page_cache altogether and uses the
page_pool to implement everything that was done by the page_cache
before:
* Let the page_pool handle dma mapping and unmapping.
* Use fragmented pages with fragment counter instead of tracking via
page ref.
* Enable skb recycling.
The patch series has the following effects on the rx path:
* Improved performance for the cases when there was low page recycling
due to head of queue blocking in the internal page_cache. The test
for this was running a single iperf TCP stream to a rx queue
which is bound on the same cpu as the application.
|-------------+--------+--------+------+---------|
| rq type | before | after | unit | diff |
|-------------+--------+--------+------+---------|
| striding rq | 30.1 | 31.4 | Gbps | 4.14 % |
| legacy rq | 30.2 | 33.0 | Gbps | 8.48 % |
|-------------+--------+--------+------+---------|
* Small XDP performance degradation. The test was is XDP drop
program running on a single rx queue with small packets incoming
it looks like this:
|-------------+----------+----------+------+---------|
| rq type | before | after | unit | diff |
|-------------+----------+----------+------+---------|
| striding rq | 19725449 | 18544617 | pps | -6.37 % |
| legacy rq | 19879931 | 18631841 | pps | -6.70 % |
|-------------+----------+----------+------+---------|
This will be handled in a different patch series by adding support for
multi-packet per page.
* For other cases the performance is roughly the same.
The above numbers were obtained on the following system:
24 core Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz
32 GB RAM
ConnectX-7 single port
The breakdown on the patch series is the following:
* Preparations for introducing the mlx5e_frag_page struct.
* Delete the mlx5e_page_cache struct.
* Enable dma mapping from page_pool.
* Enable skb recycling and fragment counting.
* Do deferred release of pages (just before alloc) to ensure better
page_pool cache utilization.
====================
* tag 'mlx5-updates-2023-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: RX, Remove unnecessary recycle parameter and page_cache stats
net/mlx5e: RX, Break the wqe bulk refill in smaller chunks
net/mlx5e: RX, Increase WQE bulk size for legacy rq
net/mlx5e: RX, Split off release path for xsk buffers for legacy rq
net/mlx5e: RX, Defer page release in legacy rq for better recycling
net/mlx5e: RX, Change wqe last_in_page field from bool to bit flags
net/mlx5e: RX, Defer page release in striding rq for better recycling
net/mlx5e: RX, Rename xdp_xmit_bitmap to a more generic name
net/mlx5e: RX, Enable skb page recycling through the page_pool
net/mlx5e: RX, Enable dma map and sync from page_pool allocator
net/mlx5e: RX, Remove internal page_cache
net/mlx5e: RX, Store SHAMPO header pages in array
net/mlx5e: RX, Remove alloc unit layout constraint for striding rq
net/mlx5e: RX, Remove alloc unit layout constraint for legacy rq
net/mlx5e: RX, Remove mlx5e_alloc_unit argument in page allocation
====================
Link: https://lore.kernel.org/r/20230328205623.142075-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: 3 Bug fixes
This series contains 3 small bug fixes covering ethtool self test, PCI
ID string typos, and some missing 200G link speed ethtool reporting logic.
====================
Link: https://lore.kernel.org/r/20230329013021.5205-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix 57502 and 57508 NPAR description string entries. The typos
caused these devices to not match up with lspci output.
Fixes: 49c98421e6 ("bnxt_en: Add PCI IDs for 57500 series NPAR devices.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
