Currently framework sets bw even when init bw requirements are zero during
provider registration, thus resulting bulk of set bw to hw.
Avoid this behaviour by skipping provider set bw calls if init bw is zero.
Signed-off-by: Vivek Aknurwar <quic_viveka@quicinc.com>
Link: https://lore.kernel.org/r/1673647679-15216-1-git-send-email-quic_viveka@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230209101310.11942cd0@endymion.delvare
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The use of the config NO_KERNEL_MSG is long gone. Remove this config from
m68k's debug kernel configuration setup.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230320123202.14474-1-lukas.bulwahn@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
nubus_bus_match() returned 1 unconditionally. This is equivalent to
no match function at all. (See driver_match_device() which does:
return drv->bus->match ? drv->bus->match(dev, drv) : 1;
.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230313180848.2770504-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Replace the unusual const char *err_msg usage with dev_err_probe which
also handles -EPROBE_DEFER better by not printing the message to kmsg.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5C73M3 8Mp camera ISP bindings to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5P/Exynos Camera Subsystem (FIMC) bindings to DT
schema. Changes during conversion - adjust to existing DTS and Linux
driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS)
bindings to DT schema. Changes during conversion - adjust to existing
DTS and Linux driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung Exynos SoC series camera host interface (FIMC-LITE)
bindings to DT schema. Changes during conversion - adjust to existing
DTS and Linux driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5P/Exynos SoC series MIPI CSI-2 receiver (MIPI
CSIS) bindings to DT schema. Changes during conversion - adjust to
existing DTS and Linux driver:
1. Add phys and power-domains.
2. Move samsung,csis-wclk property to the endpoint node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5K6A3(YX) raw image sensor bindings to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The FIMC camera node wrapper is not a bus, so using simple-bus fallback
compatible just to instantiate its children nodes was never correct.
Driver should explicitly populate all its children devices.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Driver does not handle pin configuration switching and several DTS
provide empty pinctrl property, just to satisfy the driver's requirement
for it. Drop requirement for pinctrl property as it is really optional.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The FIMC camera node wrapper is not a bus, so using simple-bus fallback
compatible just to instantiate its children nodes was never correct.
Drop the simple-bus compatible and expect driver to explicitly populate
children devices.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The documentation for the VIDIOC_SUBDEV_ENUM_FRAME_SIZE ioctl
incorrectly refers to struct v4l2_subdev_mbus_code_enum as the
parameter. Fix this.
[Sakari Ailus: Rebased on top of Dorota's documentation patch]
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This clarifies which side of the calls is responsible for doing what to
which parts of the struct. It also expands the terse description of the
access algorithm into more prose-like, active voice description, which
trades conciseness for ease of comprehension.
Fixed: typo "format" -> "frame size" in enum-frame-size
Added: no holes in the enumeration
Added: enumerations per what?
Added: who fills in what in calls
Changed: "given" -> "specified"
[Sakari Ailus: Rewrap text]
Signed-off-by: Dorota Czaplejewicz <dorota.czaplejewicz@puri.sm>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This clarifies which side of the calls is responsible for doing what to
which parts of the struct. This also explicitly states that repeating
values are disallowed. It also expands the terse description of the access
algorithm into more prose-like, active voice description, which trades
conciseness for ease of comprehension.
Added: mbus codes must not repeat
Added: no holes in the enumeration
Added: enumerations per what?
Added: who fills in what in calls
Changed: "zero" -> "0"
Changed: "given" -> "specified"
Still unclear how it works so didn't describe: "which". What is a "try
format" vs "active format"?
[Sakari Ailus: Rewrap lines, fix build issue]
Signed-off-by: Dorota Czaplejewicz <dorota.czaplejewicz@puri.sm>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290 driver can be used for both imx290 and imx327 as they have a
similar register set and configuration. imx327 lacks 8 lanes LVDS and
120 FPS support.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On auxiliary_device_init(auxdev) failure we need to do the exact same
cleanup steps as on device.release(), so use the intel_vsec_dev_release()
callback for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230320103815.229729-1-hdegoede@redhat.com
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "98e0500ead media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since the currently exported symbols in pmt_class are only used by other
Intel PMT drivers, create an INTEL_PMT module namespace for them.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230316225736.2856521-1-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit "97589ad61c media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500ead media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for A320M-S2H V2. Tested using module force_load option.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230318091441.1240921-1-frank@crawford.emu.id.au
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Discovered Intel VSEC/DVSEC capabilities are enabled by default and only
get disabled by quirk. Instead, remove such quirks and only enable support
for capabilities that have been explicitly added to a new capabilities
field. While here, also reorder the device info structures alphabetically.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230316224628.2855884-1-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The driver defines spi_device_id table for module autoloading, but does
not use it in id_table which causes W=1 warning:
drivers/platform/olpc/olpc-xo175-ec.c:737:35: error: ‘olpc_xo175_ec_id_table’ defined but not used [-Werror=unused-const-variable=]
Reference the SPI device ID table, so it can be also used for device
binding.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230316160324.78856-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make "clocks" and "power-domains" required everywhere.
Make "resets" required on R-Car Gen2 and newer (i.e. all but SH-Mobile).
Update the example to match reality:
- Use interrupt binding definitions instead of hardcoded numbers,
- Convert to new-style CPG/MSSR bindings,
- Add missing "power-domains" and "resets" properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/052af97ecbaa9ba6e0d406883dd3389fa397579a.1678891999.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230306065733.2170662-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: d593574aff ("spi: imx: do not access registers while clocks disabled")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230306065733.2170662-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307211426.2331483-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If pm_runtime_resume_and_get() failed before this change, two error
messages were printed. One directly in sprd_spi_remove() and another
by the device core as the return value is non-zero.
The better handling of a failure to resume the device is to do the
software related cleanup anyhow and only skip hardware accesses.
This leaves the device in an unknown state, but there is nothing that can
be done about that.
Even in the error case, return zero to suppress the device core's error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307211426.2331483-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230317233616.3968003-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.15 but did exist in Linux 6.1.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.6.Ibc8a86ddd5055ebbbe487a529199db7b36ccad1a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.10 but did exist in Linux 5.15.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.5.Ia0e6d859bdfe42ea5c187fb1eb4705c1b5ea23a1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.4 but did exist in Linux 5.10.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.4.I01f21c98901641a009890590ddc1354c0f294e5e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 4.19 but did exist in Linux 5.4.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.3.I45bf925ca9537da5f647e2acb0ad207c0c98af81@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 4.14 but did exist in Linux 4.19.
NOTE: from a quick "git cherry-pick" it looks as if
"bd718x7-regulator.c" didn't actually exist in v4.19. In 4.19 it was
named "bd71837-regulator.c". See commit 2ece646c90 ("regulator:
bd718xx: rename bd71837 to 718xx")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.2.Iad1f25517bb46a6c7fca8d8c80ed4fc258a79ed9@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulator is turned on
at probe time (with regulator-boot-on or regulator-always-on) and the
regulator requires delays (off-on-time, ramp time, etc).
While the overall kernel is not ready to switch to async probe by
default, as per the discussion on the mailing lists [1] it is believed
that the regulator subsystem is in good shape and we can move
regulator drivers over wholesale. There is no way to just magically
opt in all regulators (regulators are just normal drivers like
platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all
regulators found in 'drivers/regulator' individually.
Given the number of drivers touched and the impossibility to test this
ahead of time, it wouldn't be shocking at all if this caused a
regression for someone. If there is a regression caused by this patch,
it's likely to be one of the cases talked about in [1]. As a "quick
fix", drivers involved in the regression could be fixed by changing
them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix
would be to directly fix the problem that caused the issue with async
probe.
The approach here follows a similar approach that was used for the mmc
subsystem several years ago [2]. In fact, I ran nearly the same python
script to auto-generate the changes. The only thing I changed was to
search for "i2c_driver", "spmi_driver", and "spi_driver" in addition
to "platform_driver".
[1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk
[2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the snd_soc_card driver name which fixes the warning:
fsl-asoc-card sound: ASoC: driver name too long 'imx-audio-tlv320aic32x4'
-> 'imx-audio-tlv32'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230316123611.3495597-2-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of copying the driver name manually, use a common define.
No functional change.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230316123611.3495597-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
