The true Hi-Z (a.k.a. high impedance) mode is when pin is completely
disconnected from the chip. This includes input buffer as well.
Nevertheless, some hardware may not support that mode and they are
considering input only as Hi-Z, but more precisely it is an equivalent
to that, in electronics it's basically "an antenna mode".
Sligthly correct documentation to take the above into consideration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230312132523.352182-1-krzysztof.kozlowski@linaro.org
IRQ framework provides special type and getter to transform
the Linux IRQ to the hardware pin. Use that type and getter
function instead of direct access.
While at it, amend an indentation in a couple of places.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Commit f79cbc77ab ("wifi: move mac80211_hwsim and virt_wifi to virtual
directory") and commit 298e50ad8e ("wifi: move raycs, wl3501 and
rndis_wlan to legacy directory") move remaining wireless drivers into
subdirectories, but does not adjust the entries in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about
broken references.
Repair these file references in those wireless driver sections.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314041848.5120-1-lukas.bulwahn@gmail.com
To support detection of read faults with Radix execute-only memory, the
vma_is_accessible() check in access_error() (which checks for PROT_NONE)
was replaced with a check to see if VM_READ was missing, and if so,
returns true to assert the fault was caused by a bad read.
This is incorrect, as it ignores that both VM_WRITE and VM_EXEC imply
read on powerpc, as defined in protection_map[]. This causes mappings
containing VM_WRITE or VM_EXEC without VM_READ to misreport the cause of
page faults, since the MMU is still allowing reads.
Correct this by restoring the original vma_is_accessible() check for
PROT_NONE mappings, and adding a separate check for Radix PROT_EXEC-only
mappings.
Fixes: 395cac7752 ("powerpc/mm: Support execute-only memory on the Radix MMU")
Reported-by: Michal Suchánek <msuchanek@suse.de>
Link: https://lore.kernel.org/r/20230308152702.GR19419@kitsune.suse.cz
Tested-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230310050834.63105-1-ruscur@russell.cc
The gpiod_find_by_fwnode() already checks for NULL and returns
correct error code in case fwnode is invalid. Drop the respective
check and assignment in the gpiod_find_and_request().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The functions that operates on the same device object would
have the same namespace for better code understanding and
maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The devprop prefix in the devprop_gpiochip_set_names() adds confusion.
Get rid of it.
Note we have more than one function in the same module that handles
one or more device properties. This change will unify the naming schema
for all of them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/gpio/gpio-raspberrypi-exp.c:237:34: error: ‘rpi_exp_gpio_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/gpio/gpio-xra1403.c:198:34: error: ‘xra1403_spi_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-sama5d2-piobu.c:230:34: error: ‘sama5d2_piobu_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-sifive.c:263:34: error: ‘sifive_gpio_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-visconti.c:187:34: error: ‘visconti_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-rcar.c:435:34: error: ‘gpio_rcar_of_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-altera.c:324:34: error: ‘altera_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/gpio/gpio-ftgpio010.c:336:34: error: ‘ftgpio_gpio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Emails bounce: 550 5.1.1 No such user - pp
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Sometimes a GPIO is needed to turn on/off the display.
Add support for this usecase by introducing the optional 'enable-gpios'
property.
Tested on a imx53qsb board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314111724.1520178-2-festevam@denx.de
The STARRY 2081101QFH032011-53G is a 10.1" WUXGA TFT LCD panel,
which fits in nicely with the existing panel-boe-tv101wum-nl6
driver. Hence, we add a new compatible with panel specific config.
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314090549.11418-1-zhouruihai@huaqin.corp-partner.google.com
The STARRY 2081101QFH032011-53G is a 10.1" WUXGA TFT LCD panel,
which fits in nicely with the existing panel-boe-tv101wum-nl6
driver. Hence, we add a new compatible with panel specific config.
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314085034.6380-1-zhouruihai@huaqin.corp-partner.google.com
devm_regulator_get_enable_optional() returns -ENODEV if requested
optional regulator is not present. Adjust code for that, because in the
67d0a30128 I've incorrectly assumed that it also returns 0 when
regulator is not present.
Reported-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Fixes: 67d0a30128 ("drm/meson: dw-hdmi: Fix devm_regulator_*get_enable*() conversion")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309152446.104913-1-m.szyprowski@samsung.com
The returned array size for input formats is set through
atomic_get_input_bus_fmts()'s 'num_input_fmts' argument, so use
'num_input_fmts' to represent the array size in the function's kdoc,
not 'num_output_fmts'.
Fixes: 91ea83306b ("drm/bridge: Fix the bridge kernel doc")
Fixes: f32df58acc ("drm/bridge: Add the necessary bits to support bus format negotiation")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314055035.3731179-1-victor.liu@nxp.com
Appropriate maintainers should be suggested for changes to the
include/drm/drm_bridge.h header file, so add the header file to the
'DRM DRIVERS FOR BRIDGE CHIPS' section.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230313055951.2997299-1-victor.liu@nxp.com
Daniel Golle says:
====================
net: ethernet: mtk_eth_soc: minor SGMII fixes
This small series brings two minor fixes for the SGMII unit found in
MediaTek's router SoCs.
The first patch resets the PCS internal state machine on major
configuration changes, just like it is also done in MediaTek's SDK.
The second patch makes sure we only write values and restart AN if
actually needed, thus preventing unnesseray loss of an existing link
in some cases.
Both patches have previously been submitted as part of the series
"net: ethernet: mtk_eth_soc: various enhancements" which grew a bit
too big and it has correctly been criticized that some of the patches
should rather go as fixes to net-next.
This new series tries to address this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only restart auto-negotiation and write link timer if actually
necessary. This prevents losing the link in case of minor
changes.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the internal PCS state machine when changing interface mode.
This prevents confusing the state machine when changing interface
modes, e.g. from SGMII to 2500Base-X or vice-versa.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, kernel would set MSG_CTRUNC flag if msg_control buffer
wasn't provided and SO_PASSCRED was set or if there was pending SCM_RIGHTS.
For some reason we have no corresponding check for SO_PASSSEC.
In the recvmsg(2) doc we have:
MSG_CTRUNC
indicates that some control data was discarded due to lack
of space in the buffer for ancillary data.
So, we need to set MSG_CTRUNC flag for all types of SCM.
This change can break applications those don't check MSG_CTRUNC flag.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Leon Romanovsky <leon@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
v2:
- commit message was rewritten according to Eric's suggestion
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wenjia Zhang says:
====================
smc: Updates 2023-03-01
The 1st patch is to make implements later do not need to adhere to a
specific SEID format. The 2nd patch does some cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, v2 support was derived from a very specific format of the SEID
as part of the SMC-D codebase. Make this part of the SMC-D device API, so
implementers do not need to adhere to a specific SEID format.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Reviewed-and-tested-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wenjia Zhang says:
====================
net/smc: Fixes 2023-03-01
The 1st patch solves the problem that CLC message initialization was
not properly reversed in error handling path. And the 2nd one fixes
the possible deadlock triggered by cancel_delayed_work_sync().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CLC message initialization was not properly reversed in error handling path.
Reported-and-suggested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENEVE tunnel used with IFLA_GENEVE_INNER_PROTO_INHERIT is
point-to-point, so set IFF_POINTOPOINT to reflect that.
Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core already sets owner in spi_driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core already sets owner in spi_driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/ieee802154/ca8210.c:3174:34: error: ‘ca8210_of_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/ieee802154/at86rf230.c:1644:34: error: ‘at86rf230_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/ieee802154/mcr20a.c:1340:34: error: ‘mcr20a_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/ieee802154/adf7242.c:1322:34: error: ‘adf7242_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/phy/spi_ks8995.c:156:34: error: ‘ks8895_spi_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/ocelot_ext.c:143:34: error: ‘ocelot_ext_switch_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/microchip/ksz9477_i2c.c:84:34: error: ‘ksz9477_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/ocelot/seville_vsc9953.c:1070:34: error: ‘seville_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will match mostly or only by DT table (even thought there is
regular ID table) so there is little benefit in of_match_ptr (this also
allows ACPI matching via PRP0001, even though it might not be relevant
here).
drivers/net/dsa/lan9303_i2c.c:97:34: error: ‘lan9303_i2c_of_match’ defined but not used [-Werror=unused-const-variable=]
drivers/net/dsa/lan9303_mdio.c:157:34: error: ‘lan9303_mdio_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/dsa/lantiq_gswip.c:1888:34: error: ‘xway_gphy_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/nfc/trf7970a.c:2232:34: error: ‘trf7970a_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
