Add dma bindings for flexcom nodes in the soc dtsi file. Users those who
don't wish to use the DMA function for their flexcom functions can
overwrite the dma bindings in the board device tree file.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
[durai.manickamkr@microchip.com: fixed code indentation and updated commit log]
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230207110651.197268-6-durai.manickamkr@microchip.com
The ranges, #address-cells and #size-cells properties are not required,
remove them from the spi4 node.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230207110651.197268-4-durai.manickamkr@microchip.com
Move the flexcom definitions from board specific DTS file
to the SoC specific DTSI file for sam9x60ek.
[durai.manickamkr@microchip.com: Logical split-up of this patch and added
missing UART5 compatibles]
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Hari Prasath Gujulan Elango <Hari.PrasathGE@microchip.com>
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230207110651.197268-3-durai.manickamkr@microchip.com
Vladimir Oltean says:
====================
taprio automatic queueMaxSDU and new TXQ selection procedure
This patch set addresses 2 design limitations in the taprio software scheduler:
1. Software scheduling fundamentally prioritizes traffic incorrectly,
in a way which was inspired from Intel igb/igc drivers and does not
follow the inputs user space gives (traffic classes and TC to TXQ
mapping). Patch 05/15 handles this, 01/15 - 04/15 are preparations
for this work.
2. Software scheduling assumes that the gate for a traffic class closes
as soon as the next interval begins. But this isn't true.
If consecutive schedule entries have that traffic class gate open,
there is no "gate close" event and taprio should keep dequeuing from
that TC without interruptions. Patches 06/15 - 15/15 handle this.
Patch 10/15 is a generic Qdisc change required for this to work.
Future development directions which depend on this patch set are:
- Propagating the automatic queueMaxSDU calculation down to offloading
device drivers, instead of letting them calculate this, as
vsc9959_tas_guard_bands_update() does today.
- A software data path for tc-taprio with preemptible traffic and
Hold/Release events.
v1 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20230128010719.2182346-1-vladimir.oltean@nxp.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve commit 497cc00224 ("taprio: Handle short intervals and large
packets") to only perform segmentation when skb->len exceeds what
taprio_dequeue() expects.
In practice, this will make the biggest difference when a traffic class
gate is always open in the schedule. This is because the max_frm_len
will be U32_MAX, and such large skb->len values as Kurt reported will be
sent just fine unsegmented.
What I don't seem to know how to handle is how to make sure that the
segmented skbs themselves are smaller than the maximum frame size given
by the current queueMaxSDU[tc]. Nonetheless, we still need to drop
those, otherwise the Qdisc will hang.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of the taprio_enqueue()'s function is spent doing TCP
segmentation, which doesn't look right to me. Compilers shouldn't have a
problem in inlining code no matter how we write it, so move the
segmentation logic to a separate function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
taprio today has a huge problem with small TC gate durations, because it
might accept packets in taprio_enqueue() which will never be sent by
taprio_dequeue().
Since not much infrastructure was available, a kludge was added in
commit 497cc00224 ("taprio: Handle short intervals and large
packets"), which segmented large TCP segments, but the fact of the
matter is that the issue isn't specific to large TCP segments (and even
worse, the performance penalty in segmenting those is absolutely huge).
In commit a54fc09e4c ("net/sched: taprio: allow user input of per-tc
max SDU"), taprio gained support for queueMaxSDU, which is precisely the
mechanism through which packets should be dropped at qdisc_enqueue() if
they cannot be sent.
After that patch, it was necessary for the user to manually limit the
maximum MTU per TC. This change adds the necessary logic for taprio to
further limit the values specified (or not specified) by the user to
some minimum values which never allow oversized packets to be sent.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have one practical reason for doing this and one concerning correctness.
The practical reason has to do with a follow-up patch, which aims to mix
2 sources of max_sdu (one coming from the user and the other automatically
calculated based on TC gate durations @current link speed). Among those
2 sources of input, we must always select the smaller max_sdu value, but
this can change at various link speeds. So the max_sdu coming from the
user must be kept separated from the value that is operationally used
(the minimum of the 2), because otherwise we overwrite it and forget
what the user asked us to do.
To solve that, this patch proposes that struct sched_gate_list contains
the operationally active max_frm_len, and q->max_sdu contains just what
was requested by the user.
The reason having to do with correctness is based on the following
observation: the admin sched_gate_list becomes operational at a given
base_time in the future. Until then, it is inactive and applies no
shaping, all gates are open, etc. So the queueMaxSDU dropping shouldn't
apply either (this is a mechanism to ensure that packets smaller than
the largest gate duration for that TC don't hang the port; clearly it
makes little sense if the gates are always open).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinicius intended taprio to take the L1 overhead into account when
estimating packet transmission time through user input, specifically
through the qdisc size table (man tc-stab).
Something like this:
tc qdisc replace dev $eth root stab overhead 24 taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 \
sched-entry S 0x7e 9000000 \
sched-entry S 0x82 1000000 \
max-sdu 0 0 0 0 0 0 0 200 \
flags 0x0 clockid CLOCK_TAI
Without the overhead being specified, transmission times will be
underestimated and will cause late transmissions. For an offloading
driver, it might even cause TX hangs if there is no open gate large
enough to send the maximum sized packets for that TC (including L1
overhead). Properly knowing the L1 overhead will ensure that we are able
to auto-calculate the queueMaxSDU per traffic class just right, and
avoid these hangs due to head-of-line blocking.
We can't make the stab mandatory due to existing setups, but we can warn
the user that it's important with a warning netlink extack.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220505160357.298794-1-vladimir.oltean@nxp.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qdiscs like taprio turn out to be actually pretty reliant on a well
configured stab, to not underestimate the skb transmission time (by
properly accounting for L1 overhead).
In a future change, taprio will need the stab, if configured by the
user, to be available at ops->init() time. It will become even more
important in upcoming work, when the overhead will be used for the
queueMaxSDU calculation that is passed to an offloading driver.
However, rcu_assign_pointer(sch->stab, stab) is called right after
ops->init(), making it unavailable, and I don't really see a good reason
for that.
Move it earlier, which nicely seems to simplify the error handling path
as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
taprio_dequeue_from_txq() looks at the entry->end_time to determine
whether the skb will overrun its traffic class gate, as if at the end of
the schedule entry there surely is a "gate close" event for it. Hint:
maybe there isn't.
For each schedule entry, introduce an array of kernel times which
actually tracks when in the future will there be an *actual* gate close
event for that traffic class, and use that in the guard band overrun
calculation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently taprio assumes that the budget for a traffic class expires at
the end of the current interval as if the next interval contains a "gate
close" event for this traffic class.
This is, however, an unfounded assumption. Allow schedule entry
intervals to be fused together for a particular traffic class by
calculating the budget until the gate *actually* closes.
This means we need to keep budgets per traffic class, and we also need
to update the budget consumption procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a confusion in terms in taprio which makes what is called
"close_time" to be actually used for 2 things:
1. determining when an entry "closes" such that transmitted skbs are
never allowed to overrun that time (?!)
2. an aid for determining when to advance and/or restart the schedule
using the hrtimer
It makes more sense to call this so-called "close_time" "end_time",
because it's not clear at all to me what "closes". Future patches will
hopefully make better use of the term "to close".
This is an absolutely mechanical change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current taprio code operates on a very simplistic (and incorrect)
assumption: that egress scheduling for a traffic class can only take
place for the duration of the current interval, or i.o.w., it assumes
that at the end of each schedule entry, there is a "gate close" event
for all traffic classes.
As an example, traffic sent with the schedule below will be jumpy, even
though all 8 TC gates are open, so there is absolutely no "gate close"
event (effectively a transition from BIT(tc)==1 to BIT(tc)==0 in
consecutive schedule entries):
tc qdisc replace dev veth0 parent root taprio \
num_tc 2 \
map 0 1 \
queues 1@0 1@1 \
base-time 0 \
sched-entry S 0xff 4000000000 \
clockid CLOCK_TAI \
flags 0x0
This qdisc simply does not have what it takes in terms of logic to
*actually* compute the durations of traffic classes. Also, it does not
recognize the need to use this information on a per-traffic-class basis:
it always looks at entry->interval and entry->close_time.
This change proposes that each schedule entry has an array called
tc_gate_duration[tc]. This holds the information: "for how long will
this traffic class gate remain open, starting from *this* schedule
entry". If the traffic class gate is always open, that value is equal to
the cycle time of the schedule.
We'll also need to keep track, for the purpose of queueMaxSDU[tc]
calculation, what is the maximum time duration for a traffic class
having an open gate. This gives us directly what is the maximum sized
packet that this traffic class will have to accept. For everything else
it has to qdisc_drop() it in qdisc_enqueue().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify taprio_dequeue_from_txq() by noticing that we can goto one call
earlier than the previous skb_found label. This is possible because
we've unified the treatment of the child->ops->dequeue(child) return
call, we always try other TXQs now, instead of abandoning the root
dequeue completely if we failed in the peek() case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future changes will refactor the TXQ selection procedure, and a lot of
stuff will become messy, the indentation of the bulk of the dequeue
procedure would increase, etc.
Break out the bulk of the function into a new one, which knows the TXQ
(child qdisc) we should perform a dequeue from.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the handling of an unlikely condition to not stop dequeuing
if taprio failed to dequeue the peeked skb in taprio_dequeue().
I've no idea when this can happen, but the only side effect seems to be
that the atomic_sub_return() call right above will have consumed some
budget. This isn't a big deal, since either that made us remain without
any budget (and therefore, we'd exit on the next peeked skb anyway), or
we could send some packets from other TXQs.
I'm making this change because in a future patch I'll be refactoring the
dequeue procedure to simplify it, and this corner case will have to go
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't any code in the network stack which calls taprio_peek().
We only see qdisc->ops->peek() being called on child qdiscs of other
classful qdiscs, never from the generic qdisc code. Whereas taprio is
never a child qdisc, it is always root.
This snippet of a comment from qdisc_peek_dequeued() seems to confirm:
/* we can reuse ->gso_skb because peek isn't called for root qdiscs */
Since I've been known to be wrong many times though, I'm not completely
removing it, but leaving a stub function in place which emits a warning.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts says:
====================
mptcp: fixes for v6.2
Patch 1 clears resources earlier if there is no more reasons to keep
MPTCP sockets alive.
Patches 2 and 3 fix some locking issues visible in some rare corner
cases: the linked issues should be quite hard to reproduce.
Patch 4 makes sure subflows are correctly cleaned after the end of a
connection.
Patch 5 and 6 improve the selftests stability when running in a slow
environment by transfering data for a longer period on one hand and by
stopping the tests when all expected events have been observed on the
other hand.
All these patches fix issues introduced before v6.2.
====================
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 'endpoint' tests from 'mptcp_join.sh' selftest start a transfer in
the background and check the status during this transfer.
Once the expected events have been recorded, there is no reason to wait
for the data transfer to finish. It can be stopped earlier to reduce the
execution time by more than half.
For these tests, the exchanged data were not verified. Errors, if any,
were ignored but that's fine, plenty of other tests are looking at that.
It is then OK to mute stderr now that we are sure errors will be printed
(and still ignored) because the transfer is stopped before the end.
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A test-case is frequently failing on some extremely slow VMs.
The mptcp transfer completes before the script is able to do
all the required PM manipulation.
Address the issue in the simplest possible way, making the
transfer even more slow.
Additionally dump more info in case of failures, to help debugging
similar problems in the future and init dump_stats var.
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/323
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the subflow error report callback unconditionally
propagates the fallback subflow status to the owning msk.
If the msk is already orphaned, the above prevents the code
from correctly tracking the msk moving to the TCP_CLOSE state
and doing the appropriate cleanup.
All the above causes increasing memory usage over time and
sporadic self-tests failures.
There is a great deal of infrastructure trying to propagate
correctly the fallback subflow status to the owning mptcp socket,
e.g. via mptcp_subflow_eof() and subflow_sched_work_if_closed():
in the error propagation path we need only to cope with unorphaned
sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/339
Fixes: 15cc104533 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, in mptcp_pm_nl_create_listen_socket(), we need to
call the __mptcp_nmpc_socket() under the msk socket lock.
Note that as a side effect, mptcp_subflow_create_socket() needs a
'nested' lockdep annotation, as it will acquire the subflow (kernel)
socket lock under the in-kernel listener msk socket lock.
The current lack of locking is almost harmless, because the relevant
socket is not exposed to the user space, but in future we will add
more complexity to the mentioned helper, let's play safe.
Fixes: 1729cf186d ("mptcp: create the listening socket for new port")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to call the __mptcp_nmpc_socket(), and later subflow socket
access under the msk socket lock, or e.g. a racing connect() could
change the socket status under the hood, with unexpected results.
Fixes: 54635bd047 ("mptcp: add TCP_FASTOPEN_CONNECT socket option")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the peer closes all the existing subflows for a given
mptcp socket and later the application closes it, the current
implementation let it survive until the timewait timeout expires.
While the above is allowed by the protocol specification it
consumes resources for almost no reason and additionally
causes sporadic self-tests failures.
Let's move the mptcp socket to the TCP_CLOSE state when there are
no alive subflows at close time, so that the allocated resources
will be freed immediately.
Fixes: e16163b6e2 ("mptcp: refactor shutdown and close")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
net: micrel: Add support for lan8841 PHY
Add support for lan8841 PHY.
The first patch add the support for lan8841 PHY which can run at
10/100/1000Mbit. It also has support for other features, but they are not
added in this series.
The second patch updates the documentation for the dt-bindings which is
similar to the ksz9131.
v3->v4:
- add space between defines and function names
- inside lan8841_config_init use only ret variable
v2->v3:
- reuse ksz9131_config_init
- allow only open-drain configuration
- change from single patch to a patch series
v1->v2:
- Remove hardcoded values
- Fix typo in commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan8841 has the same bindings as ksz9131, so just reuse the entire
section of ksz9131.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) Ethernet physical layer transceivers for transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6,
unshielded twisted pair (UTP) cables.
The LAN8841 offers the industry-standard GMII/MII as well as the RGMII.
Some of the features of the PHY are:
- Wake on LAN
- Auto-MDIX
- IEEE 1588-2008 (V2)
- LinkMD Capable diagnosis
Currently the patch offers support only for link configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flower filter packet statistics. This will just read the TCAM
counter of the rule, which mention how many packages were hit by this
rule.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arınç reports that on his MT7621AT Unielec U7621-06 board and MT7623NI
Bananapi BPI-R2, packets received by the CPU over mt7530 switch port 0
(of which this driver acts as the DSA master) are not processed
correctly by software. More precisely, they arrive without a DSA tag
(in packet or in the hwaccel area - skb_metadata_dst()), so DSA cannot
demux them towards the switch's interface for port 0. Traffic from other
ports receives a skb_metadata_dst() with the correct port and is demuxed
properly.
Looking at mtk_poll_rx(), it becomes apparent that this driver uses the
skb vlan hwaccel area:
union {
u32 vlan_all;
struct {
__be16 vlan_proto;
__u16 vlan_tci;
};
};
as a temporary storage for the VLAN hwaccel tag, or the DSA hwaccel tag.
If this is a DSA master it's a DSA hwaccel tag, and finally clears up
the skb VLAN hwaccel header.
I'm guessing that the problem is the (mis)use of API.
skb_vlan_tag_present() looks like this:
#define skb_vlan_tag_present(__skb) (!!(__skb)->vlan_all)
So if both vlan_proto and vlan_tci are zeroes, skb_vlan_tag_present()
returns precisely false. I don't know for sure what is the format of the
DSA hwaccel tag, but I surely know that lowermost 3 bits of vlan_proto
are 0 when receiving from port 0:
unsigned int port = vlan_proto & GENMASK(2, 0);
If the RX descriptor has no other bits set to non-zero values in
RX_DMA_VTAG, then the call to __vlan_hwaccel_put_tag() will not, in
fact, make the subsequent skb_vlan_tag_present() return true, because
it's implemented like this:
static inline void __vlan_hwaccel_put_tag(struct sk_buff *skb,
__be16 vlan_proto, u16 vlan_tci)
{
skb->vlan_proto = vlan_proto;
skb->vlan_tci = vlan_tci;
}
What we need to do to fix this problem (assuming this is the problem) is
to stop using skb->vlan_all as temporary storage for driver affairs, and
just create some local variables that serve the same purpose, but
hopefully better. Instead of calling skb_vlan_tag_present(), let's look
at a boolean has_hwaccel_tag which we set to true when the RX DMA
descriptors have something. Disambiguate based on netdev_uses_dsa()
whether this is a VLAN or DSA hwaccel tag, and only call
__vlan_hwaccel_put_tag() if we're certain it's a VLAN tag.
Arınç confirms that the treatment works, so this validates the
assumption.
Link: https://lore.kernel.org/netdev/704f3a72-fc9e-714a-db54-272e17612637@arinc9.com/
Fixes: 2d7605a729 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e ("nfp: ethtool: support reporting link modes").
Fixes: 7c69873727 ("nfp: add support for .set_link_ksettings()")
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code fix a bug that sk->sk_txrehash gets its default enable
value from sysctl_txrehash only when the socket is a TCP listener.
We should have sysctl_txrehash to set the default sk->sk_txrehash,
no matter TCP, nor listerner/connector.
Tested by following packetdrill:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 socket(..., SOCK_DGRAM, IPPROTO_UDP) = 4
// SO_TXREHASH == 74, default to sysctl_txrehash == 1
+0 getsockopt(3, SOL_SOCKET, 74, [1], [4]) = 0
+0 getsockopt(4, SOL_SOCKET, 74, [1], [4]) = 0
Fixes: 26859240e4 ("txhash: Add socket option to control TX hash rethink behavior")
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577e ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The special tag is only enabled when the first MAC uses DSA. However, it
must be enabled when any MAC uses DSA. Change the check accordingly.
This fixes hardware DSA untagging not working on the second MAC of the
MT7621 and MT7623 SoCs, and likely other SoCs too. Therefore, remove the
check that disables hardware DSA untagging for the second MAC of the MT7621
and MT7623 SoCs.
Fixes: a1f47752fd ("net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC")
Co-developed-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This does not fix a real bug, since virtual addresses
are currently indentical to physical ones.
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Fix virtual vs physical address confusion (which currently are the same).
In chsc_sgib(), do the virtual-physical conversion in the caller since
the caller needs to make sure it is a 31-bit address and zero has a
special meaning (disassociating the GIB).
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Michael Mueller <mimu@linux.ibm.com>
Link: https://lore.kernel.org/r/20221107085727.1533792-1-nrb@linux.ibm.com
Message-Id: <20221107085727.1533792-1-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Replace the readl and writel with regmap to ease debugging the registers
from userspace.
Suggested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to use threaded IRQs with the PXP, as the interrupt
handler doesn't need to sleep and doesn't perform any time-consuming
operation. Switch to regular IRQ handler.
This fixes lockups of the PXP noticed on i.MX7, where the PXP would stop
generating interrupts after a variable number of frames (from a few
dozens to a few hundreds). The root cause is however unknown.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add pxp_read() and pxp_write() functions to wrap readl() and writel()
respectively. This can be useful for debugging register accesses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement support for the VIDIOC_ENUM_FRAMESIZES ioctl.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The find_format() function looks up format information for a given pixel
format. It takes a v4l2_format pointer, but only uses the contained
pixel format value. To prepare it for being used by callers that don't
have v4l2_format, modify it to take the pixel format value directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Register a media device for the PXP, using the v4l2-mem2mem MC
infrastructure to populate the media graph. No media device operation is
implemented, the main use of the MC API is to allow consistent discovery
of media devices for userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The v4l2_capability.bus_info field is set by the V4L2 core when left
empty by the .querycap() handler. This is the recommended practice, in
order to ensure bus_info coherence between drivers. Don't set it
manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Sorting headers alphabetically helps locating duplicates, and make it
easier to figure out where to insert new headers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The i.MX7D needs a different data path configuration than the i.MX6ULL.
Configure the data path as close as possible to the data path on the
i.MX6ULL.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
