If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb601 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added gpio consumer calls cause a build failure in configurations
that fail to include the right header implicitly:
drivers/usb/dwc3/dwc3-xilinx.c: In function 'dwc3_xlnx_init_zynqmp':
drivers/usb/dwc3/dwc3-xilinx.c:207:22: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_clk_get_optional'? [-Werror=implicit-function-declaration]
207 | reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
| ^~~~~~~~~~~~~~~~~~~~~~~
| devm_clk_get_optional
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230103121755.956027-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct hid_sensor_custom_properties is currently 384 bytes big, which consumes
too much stack space for no good reason. Make it dynamically allocated.
Fixes: 98c062e824 ("HID: hid-sensor-custom: Allow more custom iio sensors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The clang build reports this error
fs/udf/inode.c:805:6: error: variable 'newblock' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (*err < 0)
^~~~~~~~
newblock is never set before error handling jump.
Initialize newblock to 0 and remove redundant settings.
Fixes: d8b39db5fab8 ("udf: Handle error when adding extent to a file")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20221230175341.1629734-1-trix@redhat.com>
When extending the last extent in the file within the last block, we
wrongly computed the length of the last extent. This is mostly a
cosmetical problem since the extent does not contain any data and the
length will be fixed up by following operations but still.
Fixes: 1f3868f068 ("udf: Fix extending file within last block")
Signed-off-by: Jan Kara <jack@suse.cz>
Replace the combination of bpp and depth with a single color-mode
argument. Handle special cases in simpledrm and ofdrm. Hard-code
XRGB8888 as fallback format for cases where no given format works.
The color-mode argument accepts the same values as the kernel's video
parameter. These are mostly bpp values between 1 and 32. The exceptions
are 15, which has a color depth of 15 and a bpp value of 16; and 32,
which has a color depth of 24 and a bpp value of 32.
v4:
* add back lost test for bpp_specified (Maira)
* add Fixes tag (Daniel)
v3:
* fix ofdrm build (Maxime)
v2:
* minimize changes (Daniel)
* use drm_driver_legacy_fb_format() (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Maíra Canal <mcanal@igalia.com> # vc4 and vkms
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 37c90d589d ("drm/fb-helper: Fix single-probe color-format selection")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230106112324.22055-1-tzimmermann@suse.de
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL-terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Link: https://lore.kernel.org/r/202212280945491860150@zte.com.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
The thermal-zone-device lock is held by core when setting trip points
and the driver takes its chip lock in the corresponding callback.
Fetching the thermal trip points using thermal_zone_get_trip() also
involves taking the thermal-zone-device lock, which means that the chip
lock can not be held when doing so.
Drop the chip lock temporarily during probe to avoid the lock inversion
that was detected by lockdep:
======================================================
WARNING: possible circular locking dependency detected
6.1.0-next-20221213 #122 Not tainted
------------------------------------------------------
systemd-udevd/264 is trying to acquire lock:
ffff741e444a0920 (&chip->lock){+.+.}-{3:3}, at: qpnp_tm_get_temp+0xb4/0x1b0 [qcom_spmi_temp_alarm]
but task is already holding lock:
ffff741e44341618 (&tz->lock){+.+.}-{3:3}, at: thermal_zone_device_update+0x2c/0x70
which lock already depends on the new lock.
Fixes: 78c3e2429be8 ("thermal/drivers/qcom: Use generic thermal_zone_get_trip() function")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221214131617.2447-5-johan+linaro@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
The set_trip_temp() callback is used when changing the trip temperature
through sysfs. As it is called with the thermal-zone-device lock held
it must not use thermal_zone_get_trip() directly or it will deadlock.
Fixes: 56d7b397cc29 ("thermal/drivers/tegra: Use generic thermal_zone_get_trip() function")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221214131617.2447-4-johan+linaro@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
The set_trip_temp() callback is used when changing the trip temperature
through sysfs. As it is called with the thermal-zone-device lock held
it must not use thermal_zone_get_trip() directly or it will deadlock.
Fixes: 78c3e2429be8 ("thermal/drivers/qcom: Use generic thermal_zone_get_trip() function")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221214131617.2447-2-johan+linaro@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20221014073253.3719911-2-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
The get_trip_temp, get_trip_hyst and get_trip_type are handled by the
get_trip_point().
The set_trip_temp() generic function does some checks which are no
longer needed in the set_trip_point() ops.
Convert ops content logic into generic trip points and register them
with the thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221014073253.3719911-1-daniel.lezcano@linaro.org
Commit 13bea86623be ("thermal/of: Remove of_thermal_get_crit_temp()")
removed the function of_thermal_get_crit_temp() and this is causing a
NULL pointer deference crash when attempting to call the 'get_crit_temp'
function pointer because this function pointer is no longer initialised.
Fix this by replacing the call to the 'get_crit_temp' function pointer
with a call to the function thermal_zone_get_crit_temp() instead.
Fixes: 13bea86623be ("thermal/of: Remove of_thermal_get_crit_temp()")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221010150311.40384-1-jonathanh@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The driver is assuming the get_critical temperature exists as it is
inherited by the thermal of ops. But this one has been removed in
favor of the generic one.
Use the generic thermal_zone_get_crit_temp() function instead
Fixes: 13bea86623be ("thermal/of: Remove of_thermal_get_crit_temp(")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-30-daniel.lezcano@linaro.org
In the process of replacing the get_trip_* ops by the generic trip
points, the current code has an 'override' property to add another
indirection to a different ops.
Rework this approach to prevent this indirection and make the code
ready for the generic trip points conversion.
Actually the get_temp() is different regarding the platform, so it is
pointless to add a new set of ops but just create dynamically the ops
at init time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-29-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-28-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Kästle <peter@piie.net>
Link: https://lore.kernel.org/r/20221003092602.1323944-27-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-25-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-24-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20221003092602.1323944-23-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-22-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert to the generic trip points
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-21-daniel.lezcano@linaro.org
The thermal core is providing the generic thermal_zone_set_trip()
function which does exactly what the OF ops function is doing.
It is pointless to define our own version, just remove the ops and the
thermal_zone_set_trip() will take care of it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-19-daniel.lezcano@linaro.org
There is no benefit with the of_thermal_is_trip_valid() function as it
does the check the thermal_zone_get_trip() is already doing for the
sake of getting the trip point.
As all the calls have been replaced by thermal_zone_get_trip(), there
is no more users of of_thermal_is_trip_valid().
Remove the function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-18-daniel.lezcano@linaro.org
The thermal OF code uses the generic trip points to initialize the
thermal zone. Consequently thermal_zone_get_num_trips() can be used
and the of_thermal_get_ntrips() is no longer needed. Remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-17-daniel.lezcano@linaro.org
The thermal core framework allows to get the number of thermal trips,
use it instead of visiting the thermal core structure internals.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20221003092602.1323944-16-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-15-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Kucheria <amitk@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-14-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-13-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-12-daniel.lezcano@linaro.org
The thermal_zone_get_trip() does the same check as
of_thermal_is_trip_valid(). Replace the call to
of_thermal_is_trip_valid() by thermal_zone_get_trip().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-10-daniel.lezcano@linaro.org
The thermal core framework allows to get the number of thermal trips,
use it instead of visiting the thermal core structure internals.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-9-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
Convert ops content logic into generic trip points and register them with the
thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-8-daniel.lezcano@linaro.org
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
The thermal OF code uses the thermal_zone_device_register_with_trips()
function. It builds the trips array and pass it to the register
function. That means the get_trip_* ops are duplicated with what does
already the core code.
Remove them.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221003092602.1323944-6-daniel.lezcano@linaro.org
The governors are using the ops->get_trip_* functions, Replace these
calls with thermal_zone_get_trip().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> # IPA
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-5-daniel.lezcano@linaro.org
The thermal zone ops defines a set_trip callback where we can invoke
the backend driver to set an interrupt for the next trip point
temperature being crossed the way up or down, or setting the low level
with the hysteresis.
The ops is only called from the thermal sysfs code where the userspace
has the ability to modify a trip point characteristic.
With the effort of encapsulating the thermal framework core code,
let's create a thermal_zone_set_trip() which is the writable side of
the thermal_zone_get_trip() and put there all the ops encapsulation.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-4-daniel.lezcano@linaro.org
Instead of avoiding to expose the hysteresis attributes of a thermal
zone when its get_trip_hyst() operation is not defined, which is
confusing, expose them always and use the default
thermal_zone_get_trip() function returning 0 hysteresis when that
operation is not present.
The hysteresis of 0 is perfectly valid, so this change should not
introduce any backwards compatibility issues.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-3-daniel.lezcano@linaro.org
The thermal_zone_device_ops structure defines a set of ops family,
get_trip_temp(), get_trip_hyst(), get_trip_type(). Each of them is
returning a property of a trip point.
The result is the code is calling the ops everywhere to get a trip
point which is supposed to be defined in the backend driver. It is a
non-sense as a thermal trip can be generic and used by the backend
driver to declare its trip points.
Part of the thermal framework has been changed and all the OF thermal
drivers are using the same definition for the trip point and use a
thermal zone registration variant to pass those trip points which are
part of the thermal zone device structure.
Consequently, we can use a generic function to get the trip points
when they are stored in the thermal zone device structure.
This approach can be generalized to all the drivers and we can get rid
of the ops->get_trip_*. That will result to a much more simpler code
and make possible to rework how the thermal trip are handled in the
thermal core framework as discussed previously.
This change adds a function thermal_zone_get_trip() where we get the
thermal trip point structure which contains all the properties (type,
temp, hyst) instead of doing multiple calls to ops->get_trip_*.
That opens the door for trip point extension with more attributes. For
instance, replacing the trip points disabled bitmask with a 'disabled'
field in the structure.
Here we replace all the calls to ops->get_trip_* in the thermal core
code with a call to the thermal_zone_get_trip() function.
The thermal zone ops defines a callback to retrieve the critical
temperature. As the trip handling is being reworked, all the trip
points will be the same whatever the driver and consequently finding
the critical trip temperature will be just a loop to search for a
critical trip point type.
Provide such a generic function, so we encapsulate the ops
get_crit_temp() which can be removed when all the backend drivers are
using the generic trip points handling.
While at it, add the thermal_zone_get_num_trips() to encapsulate the
code more and reduce the grip with the thermal framework internals.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20221003092602.1323944-2-daniel.lezcano@linaro.org
Jakub Kicinski says:
====================
devlink: remove the wait-for-references on unregister
Move the registration and unregistration of the devlink instances
under their instance locks. Don't perform the netdev-style wait
for all references when unregistering the instance.
Instead the devlink instance refcount will only ensure that
the memory of the instance is not freed. All places which acquire
access to devlink instances via a reference must check that the
instance is still registered under the instance lock.
This fixes the problem of the netdev code accessing devlink
instances before they are registered.
RFC: https://lore.kernel.org/all/20221217011953.152487-1-kuba@kernel.org/
- rewrite the cover letter
- rewrite the commit message for patch 1
- un-export and rename devl_is_alive
- squash the netdevsim patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent races with netdev code accessing free devlink instances
move the registration under the devlink instance lock.
Core now waits for the instance to be registered before accessing it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
err_dl_unregister should unregister the devlink instance.
Looks like renaming it was missed in one of the reshufflings.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's most natural to register the instance first and then its
subobjects. Now that we can use the instance lock to protect
the atomicity of all init - it should also be safe.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Requiring devlink_set_features() to be run before devlink is
registered is overzealous. devlink_set_features() itself is
a leftover from old workarounds which were trying to prevent
initiating reload before probe was complete.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
