In mark_page_dirty_in_slot(), we bail out when no running vcpu exists
and a running vcpu context is strictly required by architecture. It may
cause backwards compatible issue. Currently, saving vgic/its tables is
the only known case where no running vcpu context is expected. We may
have other unknown cases where no running vcpu context exists and it's
reported by the warning message and we bail out without pushing the
dirty information to the backup bitmap. For this, the application is
going to enable the backup bitmap for the unknown cases. However, the
dirty information can't be pushed to the backup bitmap even though the
backup bitmap is enabled for those unknown cases in the application,
until the unknown cases are added to the allowed list of non-running
vcpu context with extra code changes to the host kernel.
In order to make the new application, where the backup bitmap has been
enabled, to work with the unchanged host, we continue to push the dirty
information to the backup bitmap instead of bailing out early. With the
added check on 'memslot->dirty_bitmap' to mark_page_dirty_in_slot(), the
kernel crash is avoided silently by the combined conditions: no running
vcpu context, kvm_arch_allow_write_without_running_vcpu() returns 'true',
and the backup bitmap (KVM_CAP_DIRTY_LOG_RING_WITH_BITMAP) isn't enabled
yet.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221112094322.21911-1-gshan@redhat.com
Implement ethtool_op get_link_ext_stats for PHY down events
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
The pre_ct table realizes in hardware the act_ct cache logic, bypassing
the CT table if the ct state was already set by a previous ct lookup.
As such, the pre_ct table will always miss for chain 0 filters.
Optimize the pre_ct table lookup for rules installed on chain 0.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A single async context object is sufficient to wait for the completions
of many callbacks. Switch to using one instance per a bulk of commands.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Waiting on a completion object for each callback before cleaning up their
async contexts is not necessary, as this is already implied in the
mlx5_cmd_cleanup_async_ctx() API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Work field in struct mlx5e_async_ctx is not used. Remove it.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The case where the packet is not offloaded and needs to be restored
to slow path and couldn't find expected tunnel information should not
dump a call trace to the user. there is a debug call.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Up until now, return value of update_rx was ignored. Therefore, flow
continues even if it fails. Add error flow in case of update_rx fails in
mlx5e_open_locked, mlx5i_open and mlx5i_pkey_open.
Signed-off-by: Guy Truzman <gtruzman@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Params info print was meant to be printed on load.
With time, new calls to mlx5e_init_rq_type_params and
mlx5e_build_rq_params were added, mistakenly printing
the params once again.
Move the print to were it belongs, in mlx5e_probe.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
CQE compression feature improves performance by reducing PCI bandwidth
bottleneck on CQEs write.
Enhanced CQE compression introduced in ConnectX-6 and it aims to reduce
CPU utilization of SW side packets decompression by eliminating the
need to rewrite ownership bit, which is likely to cost a cache-miss, is
replaced by validity byte handled solely by HW.
Another advantage of the enhanced feature is that session packets are
available to SW as soon as a single CQE slot is filled, instead of
waiting for session to close, this improves packet latency from NIC to
host.
Performance:
Following are tested scenarios and reults comparing basic and enahnced
CQE compression.
setup: IXIA 100GbE connected directly to port 0 and port 1 of
ConnectX-6 Dx 100GbE dual port.
Case #1 RX only, single flow goes to single queue:
IRQ rate reduced by ~ 30%, CPU utilization improved by 2%.
Case #2 IP forwarding from port 1 to port 0 single flow goes to
single queue:
Avg latency improved from 60us to 21us, frame loss improved from 0.5% to 0.0%.
Case #3 IP forwarding from port 1 to port 0 Max Throughput IXIA sends
100%, 8192 UDP flows, goes to 24 queues:
Enhanced is equal or slightly better than basic.
Testing the basic compression feature with this patch shows there is
no perfrormance degradation of the basic compression feature.
Signed-off-by: Ofer Levi <oferle@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Replace the min/max operations with a single clamp.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This is never used, and probably something that was intended to be used
before per-protocol hash tables were chosen instead.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
hca_id is an identifier of an mlx5_core instance within the hardware.
This identifier may be required for troubleshooting.
Expose it to debugfs.
Example:
$ cat /sys/kernel/debug/mlx5/mlx5_core.sf.2/vhca_id
0x12
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Before this patch, devlink traps are registered only on full driver
probe and unregistered on driver removal. As devlink traps are not
usable once driver functionality is unloaded, it should be unrgeistered
also on flows that unload the driver and then registered when loaded
back, e.g. devlink reload flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is a spelling mistake in an error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is no need for the warn if entry already removed.
Use debug print like in the update flow.
Also update the messages so user can identify if the it's
from the update flow or remove flow.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A while ago Vasily reported that it is possible to set a large number of
xattrs on inodes of filesystems that make use of the simple xattr
infrastructure. This includes all kernfs-based filesystems that support
xattrs (e.g., cgroupfs and tmpfs). Both cgroupfs and tmpfs can be
mounted by unprivileged users in unprivileged containers and root in an
unprivileged container can set an unrestricted number of security.*
xattrs and privileged users can also set unlimited trusted.* xattrs. As
there are apparently users that have a fairly large number of xattrs we
should scale a bit better. Other xattrs such as user.* are restricted
for kernfs-based instances to a fairly limited number.
Using a simple linked list protected by a spinlock used for set, get,
and list operations doesn't scale well if users use a lot of xattrs even
if it's not a crazy number. There's no need to bring in the big guns
like rhashtables or rw semaphores for this. An rbtree with a rwlock, or
limited rcu semanics and seqlock is enough.
It scales within the constraints we are working in. By far the most
common operation is getting an xattr. Setting xattrs should be a
moderately rare operation. And listxattr() often only happens when
copying xattrs between files or together with the contents to a new
file. Holding a lock across listxattr() is unproblematic because it
doesn't list the values of xattrs. It can only be used to list the names
of all xattrs set on a file. And the number of xattr names that can be
listed with listxattr() is limited to XATTR_LIST_MAX aka 65536 bytes. If
a larger buffer is passed then vfs_listxattr() caps it to XATTR_LIST_MAX
and if more xattr names are found it will return -E2BIG. In short, the
maximum amount of memory that can be retrieved via listxattr() is
limited.
Of course, the API is broken as documented on xattr(7) already. In the
future we might want to address this but for now this is the world we
live in and have lived for a long time. But it does indeed mean that
once an application goes over XATTR_LIST_MAX limit of xattrs set on an
inode it isn't possible to copy the file and include its xattrs in the
copy unless the caller knows all xattrs or limits the copy of the xattrs
to important ones it knows by name (At least for tmpfs, and kernfs-based
filesystems. Other filesystems might provide ways of achieving this.).
Bonus of this port to rbtree+rwlock is that we shrink the memory
consumption for users of the simple xattr infrastructure.
Also add proper kernel documentation to all the functions.
A big thanks to Paul for his comments.
Cc: Vasily Averin <vvs@openvz.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
A relatively large collection of fixes and new platform quirks here,
they're all fairly minor though - the widest possible impact is the fix
to the use of prefixes on regulator names which would have broken any
device that integrates regulators with DAPM and was used in a system
where it had a name prefix assigning to it.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNuPEsACgkQJNaLcl1U
h9B20wgAgLLJV/QRXtVczKYK8CkLQff07//BDyxPD/COLEe05QTc+WaPFNUqJKUv
mPmXg6br2TTDVdH+HSqeKc0yrz7o+2sLfJCZcDS3dF8lUE1X+/drhIFiuWnOwRmn
dmR7jAuJ0kPWbWsX/J0EyQlLe2vKrLq72Ila8IvUXtKVaVL2wQbVb2X8yb1bRlHs
nDj9dymIRori0fm6HAwNF7txgcL51sFy8hErAB3+qcp3mRYGSE/Xung6+Brzrpgp
eMGlrwp2xhWCKT1vvyEikhJWm+2QtWFsB0H2oURsMWboNhHqZbvN/1Lt8RuFIHLz
s3nkQUrJ9AtM0qVtR2jjm5qFK/fVog==
=8C2A
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.2-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.1
A relatively large collection of fixes and new platform quirks here,
they're all fairly minor though - the widest possible impact is the fix
to the use of prefixes on regulator names which would have broken any
device that integrates regulators with DAPM and was used in a system
where it had a name prefix assigning to it.
The latest fix for the non-contiguous memalloc helper changed the
allocation method for a non-IOMMU system to use only the fallback
allocator. This should have worked, but it caused a problem sometimes
when too many non-contiguous pages are allocated that can't be treated
by HD-audio controller.
As a quirk workaround, go back to the original strategy: use
dma_alloc_noncontiguous() at first, and apply the fallback only when
it fails, but only for non-IOMMU case.
We'll need a better fix in the fallback code as well, but this
workaround should paper over most cases.
Fixes: 9736a32513 ("ALSA: memalloc: Don't fall back for SG-buffer with IOMMU")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/CAHk-=wgSH5ubdvt76gNwa004ooZAEJL_1Q-Fyw5M2FDdqL==dg@mail.gmail.com
Link: https://lore.kernel.org/r/20221112084718.3305-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DW_IC_COMP_VERSION register contains the ASCII representation of the
Synopsys component version. Here 0x3131312A == "111*" means version
1.11* required for DW_IC_SDA_HOLD register availability where '*' means
any letter starting from 'a'.
DW_IC_COMP_TYPE is constant and is derived from two ASCII letters "DW"
followed by a 16-bit unsigned number.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Align all defines to the same column.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 90312351fd ("i2c: designware: MASTER mode as separated driver")
introduced disable_int pointer but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable_int() and scope is inside the same kernel module.
Since i2c_dw_disable_int() is just masking interrupts and the direct
DW_IC_INTR_MASK register write looks more clear in the code use that and
remove it from common code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In my opinion a few lines of spurious interrupt detection code can be
moved to the actual master interrupt handling function i2c_dw_isr()
without hurting readability.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It is kind of needless to print interrupt status when code immediately
after that finds interrupt was not originating from this device.
Therefore move it after spurious interrupt detection.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Do not return with interrupt handled if host controller is off and thus
interrupt is originating from other device or is spurious.
Add a check to detect when controller is runtime suspended or
transitioning/reset. In latter case all raw interrupt status register
bits may read one. In both cases return IRQ_NONE to indicate interrupt
was not from this device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Interrupt processing code in i2c-designware-slave.c is bit more readable
if not divided into another subroutine. Also explicit IRQ_NONE and
IRQ_HANDLED return values are more obvious.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unused completion code from i2c-designware-slave.c. Used only in
i2c-designware-master.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
These struct dw_i2c_dev members are not used in i2c-designware-slave.c
so remove re-initialization of them from i2c_dw_reg_slave().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Define software status flags with a BIT() macro. While at it remove
STATUS_IDLE and replace its use with zero initialization and status
flags clearing with a mask.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Writes from I2C bus often fail when testing the i2c-designware-slave.c
with the slave-eeprom backend. The same writes work correctly when
testing with a real 24c02 EEPROM chip.
In the tests below an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6.
1. i2cset -y 6 0x65 0x00 0x55
Single byte 0x55 write into address 0x00. No data goes into simulated
EEPROM. Debug prints from the i2c_dw_irq_handler_slave():
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
2. i2ctransfer -y 6 w9@0x65 0x00 0xff-
Write 8 bytes with decrementing value starting from 0xff at address 0x00
and forward. Only some of the data goes into arbitrary addresses.
Content is something like below but varies:
00000000 f9 f8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000050 00 00 00 00 00 00 ff fe 00 00 00 00 00 00 00 00 |................|
000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fb fa |................|
In this case debug prints were:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x510 : INTR_STAT=0x0
Both cases show there is more data coming from the receive FIFO still
after detecting the STOP condition. This can be seen from interrupt
status bits DW_IC_INTR_STOP_DET (0x200) and DW_IC_INTR_RX_FULL (0x4).
Perhaps due interrupt latencies the receive FIFO is not read fast
enough, STOP detection happens synchronously when it occurs on the I2C
bus and the DW_IC_INTR_RX_FULL keeps coming as long as there are more
bytes in the receive FIFO.
Fix this by reading the receive FIFO completely empty whenever
DW_IC_INTR_RX_FULL occurs. Use RFNE, Receive FIFO Not Empty bit in the
DW_IC_STATUS register to loop through bytes in the FIFO.
While at it do not test the return code from i2c_slave_event() for the
I2C_SLAVE_WRITE_RECEIVED since to my understanding this hardware cannot
generate NACK to incoming bytes and debug print itself does not have
much value.
Reported-by: Tian Ye <tianye@sugon.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some read types from I2C bus don't work correctly when testing the
i2c-designware-slave.c with the slave-eeprom backend. The same reads
work correctly when testing with a real 24c02 EEPROM chip.
In the following tests an i2c-designware-slave.c instance with the
slave-eeprom backend is configured to act as a simulated 24c02 at
address 0x65 on an I2C host bus 6:
1. i2cdump -y 6 0x65 b (OK)
Random read. Each byte are read using a byte address write with a
current address read in a same message.
2. i2cdump -y 6 0x65 c (OK, was NOK before commit 3b5f7f10ff when it
was repeating the 1st byte)
Repeated current address read. One byte address write message
followed by repeated current address read messages.
3. i2cdump -y 6 0x65 i (NOK, each 32 byte block repeats the 1st byte of
block)
Sequential read using SMBus Block Read. For each 32 byte block a byte
address write followed by 32 sequental reads in a same message.
These findings are explained because the implementation has had a
mismatch between hardware interrupts and what I2C slave events should be
sent after those interrupts. Despite that the case 1 happened to have
always the I2C slave events sent to a right order with a right data
between backend and the I2C bus.
Hardware generates the DW_IC_INTR_RD_REQ interrupt when another host is
attempting to read and for sequential reads after. DW_IC_INTR_RX_DONE
occurs when host does not acknowledge a transmitted byte which is an
indication the end of transmission.
Those interrupts do not match directly with I2C_SLAVE_READ_REQUESTED and
I2C_SLAVE_READ_PROCESSED events which is how the code was and is
practically using them. The slave-eeprom backend increases the buffer
index with the I2C_SLAVE_READ_PROCESSED event and returns the data from
current index when receiving only the I2C_SLAVE_READ_REQUESTED event.
That explains the repeated bytes in case 3 and also case 2 before
commit 3b5f7f10ff ("i2c: designware: slave should do WRITE_REQUESTED
before WRITE_RECEIVED").
Patch fixes the case 3 while keep cases 1 and 2 working with following
changes:
- First DW_IC_INTR_RD_REQ interrupt will change the state machine to
read in progress state, send I2C_SLAVE_READ_REQUESTED event and
transmit the first byte from backend
- Subsequent DW_IC_INTR_RD_REQ interrupts will send
I2C_SLAVE_READ_PROCESSED events and transmit next bytes from backend
- STOP won't change the state machine. Otherwise case 2 won't work since
we cannot distinguish current address read from sequentiel read
- DW_IC_INTR_RX_DONE interrupt is needless since there is no mechanism
to inform it to a backend. It cannot be used to change state machine
at the end of read either due the same reason than above
- Next host write to us will change the state machine from read to write
in progress state
- STATUS_WRITE_IN_PROGRESS and STATUS_READ_IN_PROGRESS are considered
now to be status flags not the state of the driver. This is how we
treat them in i2c-designware-master.c
While at it do not test the return code from i2c_slave_event() for
I2C_SLAVE_READ_REQUESTED and I2C_SLAVE_READ_PROCESSED since it returns
always 0.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use try_cmpxchg() (instead of cmpxchg()) in a more readable way.
oval = smp_load_acquire(&sk->sk_tsq_flags);
do {
...
} while (!try_cmpxchg(&sk->sk_tsq_flags, &oval, nval));
Reduce indentation level.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221110190239.3531280-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
try_cmpxchg() is slighly more efficient (at least on x86),
and smp_load_acquire(&sk->sk_tsq_flags) could avoid a KCSAN report.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221110174829.3403442-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No changes in generated code.
Reported-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20221110085422.521059-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
dt-bindings: net: qcom,ipa: relax some restrictions
The first patch in this series simply removes an unnecessary
requirement in the IPA binding. Previously, if the modem was doing
GSI firmware loading, the firmware name property was required to
*not* be present. There is no harm in having the firmware name be
specified, so this restriction isn't needed.
The second patch restates a requirement on the "memory-region"
property more accurately.
These binding changes have no impact on existing code or DTS files.
These aren't really bug fixes, so no need to back-port.
====================
Link: https://lore.kernel.org/r/20221110195619.1276302-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Either the AP or modem loads GSI firmware. If the modem-init
property is present, the modem loads it. Otherwise, the AP loads
it, and in that case the memory-region property must be defined.
Currently this requirement is expressed as one or the other of the
modem-init or the memory-region property being required. But it's
harmless for the memory-region to be present if the modem is loading
firmware (it'll just be ignored).
Restate the requirement so that the memory-region property is
required only if modem-init is not present.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d8604b209e ("dt-bindings: net: qcom,ipa: add firmware-name
property") added a requirement for a "firmware-name" property that
is more restrictive than necessary.
If the AP loads GSI firmware, the name of the firmware file to use
may optionally be provided via a "firmware-name" property. If the
*modem* loads GSI firmware, "firmware-name" doesn't need to be
supplied--but it's harmless to do so (it will simply be ignored).
Remove the unnecessary restriction, and allow "firware-name" to be
supplied even if it's not needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau says:
====================
mptcp: Miscellaneous refactoring and small fixes
Patches 1-3 do some refactoring to more consistently handle sock casts,
and to remove some duplicate code. No functional changes.
Patch 4 corrects a variable name in a self test, but does not change
functionality since the same value gets used due to bash's
scoping rules.
Patch 5 rewords a comment.
====================
Link: https://lore.kernel.org/r/20221110232322.125068-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We kept getting initial patches from new contributors to remove a
duplicate 'the' (since grammar checking scripts flag it), but submitters
never followed up after code review.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'time' is the local variable of run_test() function, while 'max_time' is
the local variable of do_transfer() function. So in do_transfer(),
$max_time should be used, not $time.
Please note that here $time == $max_time so the behaviour is not changed
but the right variable is used.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use '(struct sock *)msk' to get 'sk' from 'msk' in a more direct way
instead of using '&msk->sk.icsk_inet.sk'.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function mptcp_subflow_process_delegated() uses the input ssk first,
while __mptcp_check_push() invokes the packet scheduler first.
So this patch adds a new parameter named 'first' for the function
__mptcp_subflow_push_pending() to deal with these two cases separately.
With this change, the code that invokes the packet scheduler in the
function __mptcp_check_push() can be removed, and replaced by invoking
__mptcp_subflow_push_pending() directly.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use msk instead of mptcp_sk(sk) in the functions where the variable
"msk = mptcp_sk(sk)" has been defined.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several libata generic code fixes for rc5:
- Add missing translation of the SYNCHRONIZE CACHE 16 scsi command as
this command is mandatory for host-managed ZBC drives. The lack of
support for it in libata-scsi was causing issues with some
passthrough applications using ZBC drives (from Shin'ichiro).
- Fix the error path of libata-transport host, port, link and device
attributes initialization (from Yingliang).
- Prevent issuing new commands to a drive that is in the NCQ error
state and undergoing recovery (From Niklas). This bug went unnoticed
for a long time as commands issued to a drive in error state are
aborted immediately and retried by the scsi layer, hiding the useless
abort-and-retry sequence.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCY2747wAKCRDdoc3SxdoY
dto2APwMUungXAkvlc+GuvSxkgbu/0ERcaATs9l5doYAcQ2jPQD/fE6gpSaE5e3X
RGm7egQrhkTUhoZnWmHtMdHCx2QgZQ4=
=Cj/q
-----END PGP SIGNATURE-----
Merge tag 'ata-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Several libata generic code fixes for rc5:
- Add missing translation of the SYNCHRONIZE CACHE 16 scsi command as
this command is mandatory for host-managed ZBC drives.
The lack of support for it in libata-scsi was causing issues with
some passthrough applications using ZBC drives (from Shin'ichiro).
- Fix the error path of libata-transport host, port, link and device
attributes initialization (from Yingliang).
- Prevent issuing new commands to a drive that is in the NCQ error
state and undergoing recovery (From Niklas).
This bug went unnoticed for a long time as commands issued to a
drive in error state are aborted immediately and retried by the
scsi layer, hiding the useless abort-and-retry sequence"
* tag 'ata-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: do not issue non-internal commands once EH is pending
ata: libata-transport: fix error handling in ata_tdev_add()
ata: libata-transport: fix error handling in ata_tlink_add()
ata: libata-transport: fix error handling in ata_tport_add()
ata: libata-transport: fix double ata_host_put() in ata_tport_add()
ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure
We're currently hitting the WARN_ON in mctp_i2c_flow_release:
if (midev->release_count > midev->i2c_lock_count) {
WARN_ONCE(1, "release count overflow");
This may be hit if we expire a flow before sending the first packet it
contains - as we will not be pairing the increment of release_count
(performed on flow release) with the i2c lock operation (only
performed on actual TX).
To fix this, only release a flow if we've encountered it previously (ie,
dev_flow_state does not indicate NEW), as we will mark the flow as
ACTIVE at the same time as accounting for the i2c lock operation. We
also need to add an INVALID flow state, to indicate when we've done the
release.
Fixes: f5b8abf9fc ("mctp i2c: MCTP I2C binding driver")
Reported-by: Jian Zhang <zhangjian.3032@bytedance.com>
Tested-by: Jian Zhang <zhangjian.3032@bytedance.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20221110053135.329071-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'aead_req' and 'aead_send' is allocated but not freed in default switch
case. This commit fixes the potential memory leak by freeing them under
the situation.
Note that the default cases here should never be reached as they'd
mean we allowed offloading an unsupported algorithm.
Fixes: ea7a9d88ba ("net/tls: Use cipher sizes structs")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20221110090329.2036382-1-liaoyu15@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When stmmac_xdp_release() is called, there is a possibility that tx
function is still running on other queues which will lead to tx queue
timed out and reset adapter.
This commit ensure that tx function is not running xdp before release
flow continue to run.
Fixes: ac746c8520 ("net: stmmac: enhance XDP ZC driver level switching performance")
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Mohd Faizal Abdul Rahim <faizal.abdul.rahim@intel.com>
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Link: https://lore.kernel.org/r/20221110064552.22504-1-noor.azura.ahmad.tarmizi@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current driver code will read device tree node information,
and set default values if there is no info provided.
This is not done in non-OF devices leading to SGMII fifo depths being
set to the smallest size.
This patch sets the value to the default value of the PHY as stated in the
PHY datasheet.
Fixes: 4dc08dcc9f ("net: phy: dp83867: introduce critical chip default init for non-of platform")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221110054938.925347-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A problem about hinic create debugfs failed is triggered with the
following log given:
[ 931.419023] debugfs: Directory 'hinic' with parent '/' already present!
The reason is that hinic_module_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of hinic can never be created later.
hinic_module_init()
hinic_dbg_register_debugfs() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: 253ac3a979 ("hinic: add support to query sq info")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221110021642.80378-1-yuancan@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
