Several ieee80211_* symbol names are extended with _rsl tag using
macros. This is done to avoid a conflict when a similar symbol is
already in use in another part of kernel and may lead to conflicts.
However, most of these base symbol names are not found to being used
anywhere in the code and hence are not useful today. These symbols
are not used outside of the module and hence can be safely removed.
The code continues to use the original symbol names.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/17f69a042e215c484931a0327fdf7775eea5f918.1667930292.git.drv@mailo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The show() methods should only use sysfs_emit() when formatting values
to be returned to the user space.
Ref: Documentation/filesystems/sysfs.rst
Issue identified by coccicheck.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y2uEIzebbM/Fs5Jz@qemulion
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When built with Control Flow Integrity, function prototypes between
caller and function declaration must match. These mismatches are visible
at compile time with the new -Wcast-function-type-strict in Clang[1].
Fix a total of 27 warnings like these:
drivers/staging/ks7010/ks_wlan_net.c:2415:2: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_point *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
(iw_handler)ks_wlan_get_firmware_version,/* 3 KS_WLAN_GET_FIRM_VERSION */
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The ks_wlan_net Wireless Extension handler callbacks (iw_handler) use a
union for the data argument. Actually use the union and perform explicit
member selection in the function body instead of having a function
prototype mismatch. There are no resulting binary differences
before/after changes.
These changes were made partly manually and partly with the help of
Coccinelle.
Link: https://reviews.llvm.org/D134831 [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/8d2ceee1248b5a76e9b6c379f578e65482c91168.1667934775.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtw_join_timeout_handler() is a timer handler that
runs in atomic context, but it could call msleep().
As a result, the sleep-in-atomic-context bug will happen.
The process is shown below:
(atomic context)
rtw_join_timeout_handler
_rtw_join_timeout_handler
rtw_do_join
rtw_select_and_join_from_scanned_queue
rtw_indicate_disconnect
rtw_lps_ctrl_wk_cmd
lps_ctrl_wk_hdl
LPS_Leave
LPS_RF_ON_check
msleep //sleep in atomic context
Fix by removing msleep() and replacing with mdelay().
Fixes: 15865124fe ("staging: r8188eu: introduce new core dir for RTL8188eu driver")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221018083424.79741-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since model_number is allocated before it needs to be freed before
kmemdump_nul.
Reviewed-by: Konstantin Shelekhin <k.shelekhin@yadro.com>
Reviewed-by: Dmitriy Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Aleksandr Miloserdov <a.miloserdov@yadro.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver is spamming the kernel logs for entirely harmless errors from
user space submitting unsupported commands. Just silence the errors.
The application has direct access to command status, so there's no need
to log these.
And since every passthrough command now uses the quiet flag, move the
setting to the common initializer.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Alan Adamson <alan.adamson@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Correctly set send queue element opcode during immediate work request
flushing in post sendqueue operation, if the QP is in ERROR state.
An undefined ocode value results in out-of-bounds access to an array
for mapping the opcode between siw internal and RDMA core representation
in work completion generation. It resulted in a KASAN BUG report
of type 'global-out-of-bounds' during NFSoRDMA testing.
This patch further fixes a potential case of a malicious user which may
write undefined values for completion queue elements status or opcode,
if the CQ is memory mapped to user land. It avoids the same out-of-bounds
access to arrays for status and opcode mapping as described above.
Fixes: 303ae1cdfd ("rdma/siw: application interface")
Fixes: b0fff7317b ("rdma/siw: completion queue methods")
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20221107145057.895747-1-bmt@zurich.ibm.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Allow a network interface to be renamed when the interface
is up.
As described in the netconsole documentation [1], when netconsole is
used as a built-in, it will bring up the specified interface as soon as
possible. As a result, user space will not be able to rename the
interface since the kernel disallows renaming of interfaces that are
administratively up unless the 'IFF_LIVE_RENAME_OK' private flag was set
by the kernel.
The original solution [2] to this problem was to add a new parameter to
the netconsole configuration parameters that allows renaming of
the interface used by netconsole while it is administratively up.
However, during the discussion that followed, it became apparent that we
have no reason to keep the current restriction and instead we should
allow user space to rename interfaces regardless of their administrative
state:
1. The restriction was put in place over 20 years ago when renaming was
only possible via IOCTL and before rtnetlink started notifying user
space about such changes like it does today.
2. The 'IFF_LIVE_RENAME_OK' flag was added over 3 years ago in version
5.2 and no regressions were reported.
3. In-kernel listeners to 'NETDEV_CHANGENAME' do not seem to care about
the administrative state of interface.
Therefore, allow user space to rename running interfaces by removing the
restriction and the associated 'IFF_LIVE_RENAME_OK' flag. Help in
possible triage by emitting a message to the kernel log that an
interface was renamed while UP.
[1] https://www.kernel.org/doc/Documentation/networking/netconsole.rst
[2] https://lore.kernel.org/netdev/20221102002420.2613004-1-andy.ren@getcruise.com/
Signed-off-by: Andy Ren <andy.ren@getcruise.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before adding this quirk, this (mechanical keyboard) device would not be
recognized, logging:
new full-speed USB device number 56 using xhci_hcd
unable to read config index 0 descriptor/start: -32
chopping to 0 config(s)
It would take dozens of plugging/unpuggling cycles for the keyboard to
be recognized. Keyboard seems to simply work after applying this quirk.
This issue had been reported by users in two places already ([1], [2])
but nobody tried upstreaming a patch yet. After testing I believe their
suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a
little overkill. I assume this particular combination was tested because
it had been previously suggested in [3], but only NO_LPM seems
sufficient for this device.
[1]: https://qiita.com/float168/items/fed43d540c8e2201b543
[2]: https://blog.kostic.dev/posts/making-the-realforce-87ub-work-with-usb30-on-Ubuntu/
[3]: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1678477
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Dumazet <ndumazet@google.com>
Link: https://lore.kernel.org/r/20221109122946.706036-1-ndumazet@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bc27fb68aa ("include/uapi/linux/byteorder, swab: force inlining
of some byteswap operations") added __always_inline to swab functions
and commit 283d757378 ("uapi/linux/stddef.h: Provide __always_inline to
userspace headers") added a definition of __always_inline for use in
exported headers when the kernel's compiler.h is not available.
However, since swab.h does not include stddef.h, if the header soup does
not indirectly include it, the definition of __always_inline is missing,
resulting in a compilation failure, which was observed compiling the
perf tool using exported headers containing this commit:
In file included from /usr/include/linux/byteorder/little_endian.h:12:0,
from /usr/include/asm/byteorder.h:14,
from tools/include/uapi/linux/perf_event.h:20,
from perf.h:8,
from builtin-bench.c:18:
/usr/include/linux/swab.h:160:8: error: unknown type name `__always_inline'
static __always_inline __u16 __swab16p(const __u16 *p)
Fix this by replacing the inclusion of linux/compiler.h with
linux/stddef.h to ensure that we pick up that definition if required,
without relying on it's indirect inclusion. compiler.h is then included
indirectly, via stddef.h.
Fixes: 283d757378 ("uapi/linux/stddef.h: Provide __always_inline to userspace headers")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Petr Vaněk <arkamar@atlas.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rakesh Sankaranarayanan says:
====================
net: dsa: microchip: ksz_pwrite status check for lan937x and irq and error checking updates for ksz series
This patch series include following changes,
- Add KSZ9563 inside ksz_switch_chips. As per current structure,
KSZ9893 is reused inside ksz_switch_chips structure, but since
there is a mismatch in number of irq's, new member added for KSZ9563
and sku detected based on Global Chip ID 4 Register. Compatible
string from device tree mapped to KSZ9563 for spi and i2c mode
probes.
- Assign device interrupt during i2c probe operation.
- Add error checking for ksz_pwrite inside lan937x_change_mtu. After v6.0,
ksz_pwrite updated to have return type int instead of void, and
lan937x_change_mtu still uses ksz_pwrite without status verification.
- Add port_nirq as 3 for KSZ8563 switch family.
- Use dev_err_probe() instead of dev_err() to have more standardized error
formatting and logging.
v1 -> v2:
- Removed regmap validation patch from the series, planning to take
up in future after checking for any better approach and studying
the actual need for this change.
- Resolved error reported in ksz8863_smi.c file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users of these APIs in the kernel we can
remove them.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
devm_fwnode_get_gpiod_from_child() is going away as the name is too
unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
devm_fwnode_get_gpiod_from_child() is going away as the name is too
unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
"XSAVE consistency problem" has been reported under Xen, but that's the extent
of my divination skills.
Modify XSTATE_WARN_ON() to force the caller to provide relevant diagnostic
information, and modify each caller suitably.
For check_xstate_against_struct(), this removes a double WARN() where one will
do perfectly fine.
CC stable as this has been wonky debugging for 7 years and it is good to
have there too.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220810221909.12768-1-andrew.cooper3@citrix.com
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DMA to use 16B burst size with Elkhart Lake. This makes the
bus use more efficient and works around an issue which occurs with the
previously used 1B.
The fix was initially developed by Srikanth Thokala and Aman Kumar.
This together with the previous config change is the cleaned up version
of the original fix.
Fixes: 0a9410b981 ("serial: 8250_lpss: Enable DMA on Intel Elkhart Lake")
Cc: <stable@vger.kernel.org> # serial: 8250_lpss: Configure DMA also w/o DMA filter
Reported-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Co-developed-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.1.8.1.1 describes the parameter negotiation
messages and parameters. Chapter 5.4.1 states that the default parameters
are to be used if no negotiation is performed. Chapter 5.4.6.3.1 describes
the encoding of the parameter negotiation message. The meaning of the
parameters and allowed value ranges can be found in chapter 5.7.
Add parameter negotiation support accordingly. DLCI specific parameter
configuration by the user requires additional ioctls. This is subject to
another patch.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221103091743.2119-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.1 describes the encoding of the
parameter negotiation messages.
Add the parameters used there to 'gsm_mux' and 'gsm_dlci' and initialize both
according to the value ranges and recommended defaults defined in chapter 5.7.
Replace the use of the DLC default values from the 'gsm_mux' fields with the DLC
specific values from the 'gsm_dlci' fields where applicable.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm has a minimal protocol overhead of 7 bytes. The current code already
checks whether the configured MRU/MTU size is at least one byte more than
this.
Introduce the macro MIN_MTU to make this value more obvious.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
calculates RS485 delays from the baudrate. The baudrate is generated
with either a 16x or 13x divisor. The divisor is set in the Mode
Definition Register 1 (MDR1).
The commit erroneously assumes that the register stores the divisor as
a bitmask and uses a logical AND to differentiate between 16x and 13x
divisors. However the divisor is really stored as a 3-bit mode
(see lines 363ff in include/uapi/linux/serial_reg.h).
The logical AND operation is performed with UART_OMAP_MDR1_16X_MODE,
which is defined as 0x0 and hence yields false. So the commit always
assumes a 13x divisor. Fix by using an equal comparison. This works
because we never set any of the other 5 bits in the register. (They
pertain to IrDA mode, which is not supported by the driver).
Fixes: 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
Link: https://lore.kernel.org/linux-serial/202211070440.8hWunFUN-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/7d5b04da13d89b8708b9543a0b125f2b6062a77b.1667977259.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
brcmuart_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221109072110.117291-2-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA Rx completes, the current behavior is to just exit the DMA
completion handler without future actions. If the transfer is still
on-going, UART will trigger an interrupt and that eventually rearms the
DMA Rx. The extra interrupt round-trip has an inherent latency cost
that increases the risk of FIFO overrun. In such situations, the
latency margin tends to already be less due to FIFO not being empty.
Add check into DMA Rx completion handler to detect if LSR has DR (Data
Ready) still set. DR indicates there will be more characters pending
and DMA Rx can be rearmed right away to handle them.
Cc: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221107102126.56481-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the two instances of this typo present in the MSM and VT8500 serial
drivers.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20221104103719.2234098-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_buffer has flags which is only used for storing TTYB_NORMAL.
There is also a few quite confusing operations for checking the presense
of TTYB_NORMAL. Simplify things by converting flags to bool.
Despite the name remaining the same, the meaning of "flags" is altered
slightly by this change. Previously it referred to flags of the buffer
(only TTYB_NORMAL being used as a flag). After this change, flags tell
whether the buffer contains/should be allocated with flags array along
with character data array. It is much more suitable name that
TTYB_NORMAL was for this purpose, thus the name remains.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019105504.16800-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though our EFI zboot decompressor is pedantically spec compliant
and idiomatic for EFI image loaders, calling LoadImage() and
StartImage() for the nested image is a bit of a burden. Not only does it
create workflow issues for the distros (as both the inner and outer
PE/COFF images need to be signed for secure boot), it also copies the
image around in memory numerous times:
- first, the image is decompressed into a buffer;
- the buffer is consumed by LoadImage(), which copies the sections into
a newly allocated memory region to hold the executable image;
- once the EFI stub is invoked by StartImage(), it will also move the
image in memory in case of KASLR, mirrored memory or if the image must
execute from a certain a priori defined address.
There are only two EFI spec compliant ways to load code into memory and
execute it:
- use LoadImage() and StartImage(),
- call ExitBootServices() and take ownership of the entire system, after
which anything goes.
Given that the EFI zboot decompressor always invokes the EFI stub, and
given that both are built from the same set of objects, let's merge the
two, so that we can avoid LoadImage()/StartImage but still load our
image into memory without breaking the above rules.
This also means we can decompress the image directly into its final
location, which could be randomized or meet other platform specific
constraints that LoadImage() does not know how to adhere to. It also
means that, even if the encapsulated image still has the EFI stub
incorporated as well, it does not need to be signed for secure boot when
wrapping it in the EFI zboot decompressor.
In the future, we might decide to retire the EFI stub attached to the
decompressed image, but for the time being, they can happily coexist.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The LoongArch build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, the EFI entry code for LoongArch is set up to copy the
executable image to the preferred offset, but instead of branching
directly into that image, it branches to the local copy of kernel_entry,
and relies on the logic in that function to switch to the link time
address instead.
This is a bit sloppy, and not something we can support once we merge the
EFI decompressor with the EFI stub. So let's clean this up a bit, by
adding a helper that computes the offset of kernel_entry from the start
of the image, and simply adding the result to VMLINUX_LOAD_ADDRESS.
And considering that we cannot execute from anywhere else anyway, let's
avoid efi_relocate_kernel() and just allocate the pages instead.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The arm64 build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
While at it, introduce a helper routine that the generic zboot loader
will need to invoke after decompressing the image but before invoking
it, to ensure that the I-side view of memory is consistent.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The RISC-V build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Factor out the expressions that describe the preferred placement of the
loaded image as well as the minimum alignment so we can reuse them in
the decompressor.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In order to be able to switch from LoadImage() [which treats the
supplied PE/COFF image as file input only, and reconstructs the memory
image based on the section descriptors] to a mode where we allocate the
memory directly, and invoke the image in place, we need to now how much
memory to allocate beyond the end of the image. So copy this information
from the payload's PE/COFF header to the end of the compressed version
of the payload, so that the decompressor app can access it before
performing the decompression itself.
We'll also need to size of the code region once we switch arm64 to
jumping to the kernel proper with MMU and caches enabled, so let's
capture that information as well. Note that SizeOfCode does not account
for the header, so we need SizeOfHeaders as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for allowing the EFI zboot decompressor to reuse most of
the EFI stub machinery, factor out the actual EFI PE/COFF entrypoint
into a separate file.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Clone the implementations of strrchr() and memchr() in lib/string.c so
we can use them in the standalone zboot decompressor app. These routines
are used by the FDT handling code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, arm64, RISC-V and LoongArch rely on the fact that struct
screen_info can be accessed directly, due to the fact that the EFI stub
and the core kernel are part of the same image. This will change after a
future patch, so let's ensure that the screen_info handling is able to
deal with this, by adopting the arm32 approach of passing it as a
configuration table. While at it, switch to ACPI reclaim memory to hold
the screen_info data, which is more appropriate for this kind of
allocation.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Drop the __efistub_ prefixed exports of various routines that the EFI
stub on LoongArch does not even use.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Split the efi_printk() routine into its own source file, and provide
local implementations of strlen() and strnlen() so that the standalone
zboot app can efi_err and efi_info etc.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We will no longer be able to call into the kernel image once we merge
the decompressor with the EFI stub, so we need our own implementation of
memcmp(). Let's add the one from lib/string.c and simplify it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
