1. STM32 FMC2:
a. Correct in bindings the name of property for address
setup duration. The DTS and driver were already using proper name,
so it is only alignment of bindings with real usage.
b. Split off STM32 memory controller bus peripheral properties into
generic ones (re-usable by multiple memory controllers) and STM32 bus
peripheral. This way, the FMC2 controller properties in Micrel
KSZ8851MLL ethernet controller node can be properly validated.
2. Tegra MC: simplify with DEFINE_SHOW_ATTRIBUTE.
3. Renesas RPC IF: add suppor tfor R-Car Gen4.
4. LPDDR bindings: refactor and extend with description of DDR channels.
Add also bindings for LPDDR4 and LPDDR5.
The rationale for (4) above - LPDDR bindings changes, wrote by Julius Werner:
"We (Chromium OS) have been trying to find a way to pass LPDDR memory
chip information that is available to the firmware through the FDT
(mostly for userspace informational purposes, for now). We have been
using and expanding the existing "jedec,lpddr2" and "jedec,lpddr3"
bindings for this (e.g. [1]). The goal is to be able to identify the
memory layout of the system (how the parts look like, how they're tied
together, how much capacity there is in total) as accurately as
possible from software-probed values.
...
The problem with this is that each individual LPDDR chip has its own
set of mode registers (per rank) that only describe the density of
that particular chip (rank). The host memory controller may have
multiple channels (each of which is basically an entirely separate set
of physical LPDDR pins on the board), a single channel may be
connected to multiple LPDDR chips (e.g. if the memory controller has
an outgoing 32-bit channel, that channel could be tied to two 16-bit
LPDDR chips by tying the low 16 bits to one and the high 16 bits to
the other), and then each of those chips may offer multiple
independent ranks (which rank is being accessed at a given time is
controlled by a separate chip select pin).
So if we just have one "io-width" and one "density" field in the FDT,
there's no way to figure out how much memory there's actually
connected in total, because that only describes a single LPDDR chip.
Worse, there may be chips where different ranks have different
densities (e.g. a 6GB dual-rank chip with one 4GB and one 2GB rank),
and different channels could theoretically be connected to chips of
completely different manufacturers."
Link: https://lore.kernel.org/r/CAODwPW9E8wWwxbYKyf4_-JFb4F-JSmLR3qOF_iudjX0f9ndF0A@mail.gmail.com
-----BEGIN PGP SIGNATURE-----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=ancn
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HLKR
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v6.2
1. STM32 FMC2:
a. Correct in bindings the name of property for address
setup duration. The DTS and driver were already using proper name,
so it is only alignment of bindings with real usage.
b. Split off STM32 memory controller bus peripheral properties into
generic ones (re-usable by multiple memory controllers) and STM32 bus
peripheral. This way, the FMC2 controller properties in Micrel
KSZ8851MLL ethernet controller node can be properly validated.
2. Tegra MC: simplify with DEFINE_SHOW_ATTRIBUTE.
3. Renesas RPC IF: add suppor tfor R-Car Gen4.
4. LPDDR bindings: refactor and extend with description of DDR channels.
Add also bindings for LPDDR4 and LPDDR5.
The rationale for (4) above - LPDDR bindings changes, wrote by Julius Werner:
"We (Chromium OS) have been trying to find a way to pass LPDDR memory
chip information that is available to the firmware through the FDT
(mostly for userspace informational purposes, for now). We have been
using and expanding the existing "jedec,lpddr2" and "jedec,lpddr3"
bindings for this (e.g. [1]). The goal is to be able to identify the
memory layout of the system (how the parts look like, how they're tied
together, how much capacity there is in total) as accurately as
possible from software-probed values.
...
The problem with this is that each individual LPDDR chip has its own
set of mode registers (per rank) that only describe the density of
that particular chip (rank). The host memory controller may have
multiple channels (each of which is basically an entirely separate set
of physical LPDDR pins on the board), a single channel may be
connected to multiple LPDDR chips (e.g. if the memory controller has
an outgoing 32-bit channel, that channel could be tied to two 16-bit
LPDDR chips by tying the low 16 bits to one and the high 16 bits to
the other), and then each of those chips may offer multiple
independent ranks (which rank is being accessed at a given time is
controlled by a separate chip select pin).
So if we just have one "io-width" and one "density" field in the FDT,
there's no way to figure out how much memory there's actually
connected in total, because that only describes a single LPDDR chip.
Worse, there may be chips where different ranks have different
densities (e.g. a 6GB dual-rank chip with one 4GB and one 2GB rank),
and different channels could theoretically be connected to chips of
completely different manufacturers."
Link: https://lore.kernel.org/r/CAODwPW9E8wWwxbYKyf4_-JFb4F-JSmLR3qOF_iudjX0f9ndF0A@mail.gmail.com
* tag 'memory-controller-drv-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory-controller: st,stm32: Split off MC properties
dt-bindings: memory: Add jedec,lpddrX-channel binding
dt-bindings: memory: Add jedec,lpddr4 and jedec,lpddr5 bindings
dt-bindings: memory: Add numeric LPDDR compatible string variant
dt-bindings: memory: Factor out common properties of LPDDR bindings
memory: renesas-rpc-if: Add support for R-Car Gen4
memory: renesas-rpc-if: Clear HS bit during hardware initialization
dt-bindings: memory: renesas,rpc-if: Document R-Car V4H support
memory: tegra186-emc: use DEFINE_SHOW_ATTRIBUTE to simplify code
memory: tegra210-emc: use DEFINE_SHOW_ATTRIBUTE to simplify code
memory: tegra30-emc: use DEFINE_SHOW_ATTRIBUTE to simplify code
memory: tegra20-emc: use DEFINE_SHOW_ATTRIBUTE to simplify code
dt-bindings: memory-controller: st,stm32: Fix st,fmc2_ebi-cs-write-address-setup-ns
Link: https://lore.kernel.org/r/20221026171354.51877-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If a system does not have swap and memory is under 100% usage,
amdgpu will fail to evict resources. Currently the suspend
carries on proceeding to reset the GPU:
```
[drm] evicting device resources failed
[drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <vcn_v3_0> failed -12
[drm] free PSP TMR buffer
[TTM] Failed allocating page table
[drm] evicting device resources failed
amdgpu 0000:03:00.0: amdgpu: MODE1 reset
amdgpu 0000:03:00.0: amdgpu: GPU mode1 reset
amdgpu 0000:03:00.0: amdgpu: GPU smu mode1 reset
```
At this point if the suspend actually succeeded I think that amdgpu
would have recovered because the GPU would have power cut off and
restored. However the kernel fails to continue the suspend from the
memory pressure and amdgpu fails to run the "resume" from the aborted
suspend.
```
ACPI: PM: Preparing to enter system sleep state S3
SLUB: Unable to allocate memory on node -1, gfp=0xdc0(GFP_KERNEL|__GFP_ZERO)
cache: Acpi-State, object size: 80, buffer size: 80, default order: 0, min order: 0
node 0: slabs: 22, objs: 1122, free: 0
ACPI Error: AE_NO_MEMORY, Could not update object reference count (20210730/utdelete-651)
[drm:psp_hw_start [amdgpu]] *ERROR* PSP load kdb failed!
[drm:psp_resume [amdgpu]] *ERROR* PSP resume failed
[drm:amdgpu_device_fw_loading [amdgpu]] *ERROR* resume of IP block <psp> failed -62
amdgpu 0000:03:00.0: amdgpu: amdgpu_device_ip_resume failed (-62).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x100 returns -62
amdgpu 0000:03:00.0: PM: failed to resume async: error -62
```
To avoid this series of unfortunate events, fail amdgpu's suspend
when the memory eviction fails. This will let the system gracefully
recover and the user can try suspend again when the memory pressure
is relieved.
Reported-by: post@davidak.de
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2223
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAmNhDBYACgkQAEG6vDF+
4phghw/+NOs8NupkeiiYvio5PexgBK1lcXhp9iznmTo0s4cjyAaFC6/rolIGGKsx
+HsG/MU62jYhYNtp449TMhV4czEk5REJbY5KMtRO0/Cr35IOlfZYHloZfy5da3SS
UDhITTNmq/FOOzDq4293kiX+zb5M+wlL54WUba0MpcSXqJM4AM6mKJBmEtq7MLgB
UL3lbyMEv6VLCbWtxVAlReQszbEKZy3/wW1uTfUJ85n1aka8SGW2IK0RiBl9hSem
k7oMe4a5Lu5/GGMn/DDVHEKpidc11qGZo0wMh3Iu00a6c/h0QZABGVa/oU8TppoO
CqiczsybT3/ZGN6DIqzzTyITpxvW4bsV5twvYn5A7YnhUoz5jL9MZgdlxJpbu65D
QSI4U2XXhHy3IwBSqBVxVdaqCKO5MUFPHnBX8SNJ72OM2bvP4S7pz6L5KFkwr2BK
cuFj+ra1iIS7JnvGBQYuKXac2Jw/nCDfUfQiH8CmjKth9x9JMUYu0dHuiyMuuodO
VcGzm/Y5T18tZVfiJMVdy0HB3DWj+T+jN0rE4zpyoqesNckIRSUZtoiV3uwvVDDU
HZwsS9LDCJY3TURftjJCusaQr1Nix8lVElYOR4v7niePMsc3FYfcPHhLUMvJAWYm
HhPbDBfGajitgWsm6rEzwjSRAn6SKOafEOcK4YRvkIv36MUJYsw=
=mi0I
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Armv8 Juno fix for v6.1
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add thermal critical trip points
Link: https://lore.kernel.org/r/20221102140156.2758137-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2549
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Use mes.sched_version, mes.kiq_version for debugfs as
mes.ucode_fw_version does not contain correct versioning information.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch to fix the gdm3 start failure with virual display:
/usr/libexec/gdm-x-session[1711]: (II) AMDGPU(0): Setting screen physical size to 270 x 203
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to make import prime FD as pixmap: 22
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument
/usr/libexec/gdm-x-session[1711]: (WW) AMDGPU(0): Failed to set mode on CRTC 0
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): Failed to enable any CRTC
gnome-shell[1840]: Running GNOME Shell (using mutter 42.2) as a X11 window and compositing manager
/usr/libexec/gdm-x-session[1711]: (EE) AMDGPU(0): failed to set mode: Invalid argument
vkms doesn't have modifiers support, set fb_modifiers_not_supported to bring the gdm back.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missing send cursor_rect width & Height into DMUB. PSR-SU would use
these information. But missing these assignment in last refactor commit
Reported-by: Timur Kristóf <timur.kristof@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2227
Fixes: b73353f7f3 ("drm/amd/display: Use the same cursor info across features")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missed enabling timing sync on DCN32 because DCN32 has a different DML
param.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
-----BEGIN PGP SIGNATURE-----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=9hru
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=jNDG
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fixes for v6.1
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
* tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix deferred_tx_wq release on error paths
firmware: arm_scmi: Fix devres allocation device in virtio transport
firmware: arm_scmi: Make Rx chan_setup fail on memory errors
firmware: arm_scmi: Make tx_prepare time out eventually
firmware: arm_scmi: Suppress the driver's bind attributes
firmware: arm_scmi: Cleanup the core driver removal callback
Link: https://lore.kernel.org/r/20221102140142.2758107-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Why]
Cannot report 0 memclk levels even when SMU does not provide any.
[How]
When memclk levels reported by SMU is 0, set levels to 1.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
Update DF related latencies based on new measurements.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
[why]
Hardware team recommends we limit dispclock to 1950Mhz for all DCN3.2.x
[how]
Limit to 1950 when initializing clocks.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
Ignore cable ID for DP2 receivers that does not support the feature.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the new compatible for HiSilicon i2c.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The HiSilicon I2C controller can be used on embedded platform, which
boot from devicetree.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C controller IP used in the Allwinner F1C100s series of SoCs is
compatible with the ones used in the other Allwinner SoCs.
Add an F1C100s specific compatible string to the list of existing names.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add missing devm_i2c_add_adapter() to devres.rst. It's introduced by
commit 07740c92ae ("i2c: core: add managed function for adding i2c
adapters").
Fixes: 07740c92ae ("i2c: core: add managed function for adding i2c adapters")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implement a robust overflows_type() macro to test if a variable or
constant value would overflow another variable or type. This can be
used as a constant expression for static_assert() (which requires a
constant expression[1][2]) when used on constant values. This must be
constructed manually, since __builtin_add_overflow() does not produce
a constant expression[3].
Additionally adds castable_to_type(), similar to __same_type(), but for
checking if a constant value would overflow if cast to a given type.
Add unit tests for overflows_type(), __same_type(), and castable_to_type()
to the existing KUnit "overflow" test:
[16:03:33] ================== overflow (21 subtests) ==================
...
[16:03:33] [PASSED] overflows_type_test
[16:03:33] [PASSED] same_type_test
[16:03:33] [PASSED] castable_to_type_test
[16:03:33] ==================== [PASSED] overflow =====================
[16:03:33] ============================================================
[16:03:33] Testing complete. Ran 21 tests: passed: 21
[16:03:33] Elapsed time: 24.022s total, 0.002s configuring, 22.598s building, 0.767s running
[1] https://en.cppreference.com/w/c/language/_Static_assert
[2] C11 standard (ISO/IEC 9899:2011): 6.7.10 Static assertions
[3] https://gcc.gnu.org/onlinedocs/gcc/Integer-Overflow-Builtins.html
6.56 Built-in Functions to Perform Arithmetic with Overflow Checking
Built-in Function: bool __builtin_add_overflow (type1 a, type2 b,
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: Vitor Massaru Iha <vitor@massaru.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-hardening@vger.kernel.org
Cc: llvm@lists.linux.dev
Co-developed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221024201125.1416422-1-gwan-gyeong.mun@intel.com
The launchtime offset should be corrected according to sections 7.5.2.6
Transmit Scheduling Latency of the Intel Ethernet I225/I226 Software
User Manual.
Software can compensate the latency between the transmission scheduling
and the time that packet is transmitted to the network by setting this
GTxOffset register. Without setting this register, there may be a
significant delay between the packet scheduling and the network point.
This patch helps to reduce the latency for each of the link speed.
Before:
10Mbps : 11000 - 13800 nanosecond
100Mbps : 1300 - 1700 nanosecond
1000Mbps : 190 - 600 nanosecond
2500Mbps : 1400 - 1700 nanosecond
After:
10Mbps : less than 750 nanosecond
100Mbps : less than 192 nanosecond
1000Mbps : less than 128 nanosecond
2500Mbps : less than 128 nanosecond
Test Setup:
Talker : Use l2_tai.c to generate the launchtime into packet payload.
Listener: Use timedump.c to compute the delta between packet arrival and
LaunchTime packet payload.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the serial port 8250_gsc.c driver to 8250_parisc.c and cleanup
how the device IDs of devices in a PA-RISC machine are shown at startup.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY2KHWQAKCRD3ErUQojoP
XwzoAQCOzXAVgz2XsZuNtAdap/Q/02kcCToTOPqJcvuaXbm87QEAwXGN8XWpdTli
n2Egvuq5T2LFMSq3ERqGOVj502hYfwo=
=UWoU
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"This mostly handles oddities with the serial port 8250_gsc.c driver.
Although the name suggests it's just for serial ports on the GSC bus
(e.g. in older PA-RISC machines), it handles serial ports on PA-RISC
PCI devices (e.g. on the SuperIO chip) as well.
Thus this renames the driver to 8250_parisc and fixes the config
dependencies.
The other change is a cleanup on how the device IDs of devices in a
PA-RISC machine are shown at startup"
* tag 'parisc-for-6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Avoid printing the hardware path twice
parisc: Export iosapic_serial_irq() symbol for serial port driver
MAINTAINERS: adjust entry after renaming parisc serial driver
parisc: Use signed char for hardware path in pdc.h
parisc/serial: Rename 8250_gsc.c to 8250_parisc.c
parisc: Make 8250_gsc driver dependend on CONFIG_PARISC
Daniel Xu reported that the hash:net,iface type of the ipset subsystem does
not limit adding the same network with different interfaces to a set, which
can lead to huge memory usage or allocation failure.
The quick reproducer is
$ ipset create ACL.IN.ALL_PERMIT hash:net,iface hashsize 1048576 timeout 0
$ for i in $(seq 0 100); do /sbin/ipset add ACL.IN.ALL_PERMIT 0.0.0.0/0,kaf_$i timeout 0 -exist; done
The backtrace when vmalloc fails:
[Tue Oct 25 00:13:08 2022] ipset: vmalloc error: size 1073741848, exceeds total pages
<...>
[Tue Oct 25 00:13:08 2022] Call Trace:
[Tue Oct 25 00:13:08 2022] <TASK>
[Tue Oct 25 00:13:08 2022] dump_stack_lvl+0x48/0x60
[Tue Oct 25 00:13:08 2022] warn_alloc+0x155/0x180
[Tue Oct 25 00:13:08 2022] __vmalloc_node_range+0x72a/0x760
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_add+0x7c0/0xb20
[Tue Oct 25 00:13:08 2022] ? __kmalloc_large_node+0x4a/0x90
[Tue Oct 25 00:13:08 2022] kvmalloc_node+0xa6/0xd0
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_resize+0x99/0x710
<...>
The fix is to enforce the limit documented in the ipset(8) manpage:
> The internal restriction of the hash:net,iface set type is that the same
> network prefix cannot be stored with more than 64 different interfaces
> in a single set.
Fixes: ccf0a4b7fc ("netfilter: ipset: Add bucketsize parameter to all hash types")
Reported-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix a few more of the usual sorts of bugs:
- Another regression with source route validation in CMA, introduced this
merge window
- Crash in hfi1 due to faulty list operations
- PCI ID updates for EFA
- Disable LOCAL_INV in hns because it causes a HW hang
- Crash in hns due to missing initialization
- Memory leak in rxe
- Missing error unwind during ib_core module loading
- Missing error handling in qedr around work queue creation during startup
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCY2JgFQAKCRCFwuHvBreF
Yf1bAQChHuVuXM6BlX2wB8CoEZDqefHsOyuDbLCLlbqn3brCwAD/RmzK0jZfkFV2
xiE6vZJNSqmfvIyUJtzQY2TfgH0TpgE=
=T7AL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Fix a few more of the usual sorts of bugs:
- Another regression with source route validation in CMA, introduced
this merge window
- Crash in hfi1 due to faulty list operations
- PCI ID updates for EFA
- Disable LOCAL_INV in hns because it causes a HW hang
- Crash in hns due to missing initialization
- Memory leak in rxe
- Missing error unwind during ib_core module loading
- Missing error handling in qedr around work queue creation during
startup"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/qedr: clean up work queue on failure in qedr_alloc_resources()
RDMA/core: Fix null-ptr-deref in ib_core_cleanup()
RDMA/rxe: Fix mr leak in RESPST_ERR_RNR
RDMA/hns: Fix NULL pointer problem in free_mr_init()
RDMA/hns: Disable local invalidate operation
RDMA/efa: Add EFA 0xefa2 PCI ID
IB/hfi1: Correctly move list in sc_disable()
RDMA/cma: Use output interface for net_dev check
buffer_info->rxbuf.page accessed in e1000_clean_jumbo_rx_irq() is
allocated using GFP_ATOMIC. Pages allocated with GFP_ATOMIC can't come from
highmem and so there's no need to kmap() them. Just use page_address().
I don't have access to a 32-bit system so did some limited testing on
qemu (qemu-system-i386 -m 4096 -smp 4 -device e1000e) with a 32-bit
Debian 11.04 image.
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
alloc_rx_buf() allocates ps_page->page and buffer_info->page using either
GFP_ATOMIC or GFP_KERNEL. Memory allocated with GFP_KERNEL/GFP_ATOMIC can't
come from highmem and so there's no need to kmap() them. Just use
page_address().
I don't have access to a 32-bit system so did some limited testing on qemu
(qemu-system-i386 -m 4096 -smp 4 -device e1000e) with a 32-bit Debian 11.04
image.
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add tracepoints to the driver via a new file e1000e_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for s0ix flows to help in a debug of shared resources with the CSME
firmware. The idea here is that tracepoints have such low performance cost
when disabled that we can leave these in the upstream driver.
Performance not affected, and this can be very useful for debugging and
adding new trace events to paths in the future.
Usage:
echo "e1000e_trace:*" > /sys/kernel/debug/tracing/set_event
echo 1 > /sys/kernel/debug/tracing/events/e1000e_trace/enable
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms.
This patch provides the initial support for these devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ignore guest CPUID for host userspace writes to the DEBUGCTL MSR, KVM's
ABI is that setting CPUID vs. state can be done in any order, i.e. KVM
allows userspace to stuff MSRs prior to setting the guest's CPUID that
makes the new MSR "legal".
Keep the vmx_get_perf_capabilities() check for guest writes, even though
it's technically unnecessary since the vCPU's PERF_CAPABILITIES is
consulted when refreshing LBR support. A future patch will clean up
vmx_get_perf_capabilities() to avoid the RDMSR on every call, at which
point the paranoia will incur no meaningful overhead.
Note, prior to vmx_get_perf_capabilities() checking that the host fully
supports LBRs via x86_perf_get_lbr(), KVM effectively relied on
intel_pmu_lbr_is_enabled() to guard against host userspace enabling LBRs
on platforms without full support.
Fixes: c646236344 ("KVM: vmx/pmu: Add PMU_CAP_LBR_FMT check when guest LBR is enabled")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221006000314.73240-5-seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold vmx_supported_debugctl() into vcpu_supported_debugctl(), its only
caller. Setting bits only to clear them a few instructions later is
rather silly, and splitting the logic makes things seem more complicated
than they actually are.
Opportunistically drop DEBUGCTLMSR_LBR_MASK now that there's a single
reference to the pair of bits. The extra layer of indirection provides
no meaningful value and makes it unnecessarily tedious to understand
what KVM is doing.
No functional change.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221006000314.73240-4-seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Advertise LBR support to userspace via MSR_IA32_PERF_CAPABILITIES if and
only if perf fully supports LBRs. Perf may disable LBRs (by zeroing the
number of LBRs) even on platforms the allegedly support LBRs, e.g. if
probing any LBR MSRs during setup fails.
Fixes: be635e34c2 ("KVM: vmx/pmu: Expose LBR_FMT in the MSR_IA32_PERF_CAPABILITIES")
Reported-by: Like Xu <like.xu.linux@gmail.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221006000314.73240-3-seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit d99884ad9e in ath-next
as users are seeing this bug more now, also cc stable)
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock+0x17/0x20
ath11k_regd_update+0x15a/0x260 [ath11k]
ath11k_regd_update_work+0x15/0x20 [ath11k]
process_one_work+0x228/0x670
worker_thread+0x4d/0x440
kthread+0x16d/0x1b0
ret_from_fork+0x22/0x30
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath11k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath11k_mac_op_stop: (ffffffffc14187a0)
drv_stop+0x30 ([mac80211])
ieee80211_do_stop+0x5d2 ([mac80211])
ieee80211_stop+0x3e ([mac80211])
__dev_close_many+0x9e ([kernel.kallsyms])
__dev_change_flags+0xbe ([kernel.kallsyms])
dev_change_flags+0x23 ([kernel.kallsyms])
devinet_ioctl+0x5e3 ([kernel.kallsyms])
inet_ioctl+0x197 ([kernel.kallsyms])
sock_do_ioctl+0x4d ([kernel.kallsyms])
sock_ioctl+0x264 ([kernel.kallsyms])
__x64_sys_ioctl+0x92 ([kernel.kallsyms])
do_syscall_64+0x3a ([kernel.kallsyms])
entry_SYSCALL_64_after_hwframe+0x63 ([kernel.kallsyms])
__GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Cc: <stable@vger.kernel.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
[kvalo: improve commit log]
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
The 2.7.0 series of QCN9074's firmware requests 5 segments
of memory instead of 3 (as in the 2.5.0 series).
The first segment (11M) is too large to be kalloc'd in one
go on x86 and requires piecemeal 1MB allocations, as was
the case with the prior public firmware (2.5.0, 15M).
Since f6f92968e1, ath11k will break the memory requests,
but only if there were fewer than 3 segments requested by
the firmware. It seems that 5 segments works fine and
allows QCN9074 to boot on x86 with firmware 2.7.0, so
change things accordingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221022042728.43015-1-stachecki.tyler@gmail.com
ath11k_mac_he_gi_to_nl80211_he_gi() generates a valid warning with gcc-13:
drivers/net/wireless/ath/ath11k/mac.c:321:20: error: conflicting types for 'ath11k_mac_he_gi_to_nl80211_he_gi' due to enum/integer mismatch; have 'enum nl80211_he_gi(u8)'
drivers/net/wireless/ath/ath11k/mac.h:166:5: note: previous declaration of 'ath11k_mac_he_gi_to_nl80211_he_gi' with type 'u32(u8)'
I.e. the type of the return value ath11k_mac_he_gi_to_nl80211_he_gi() in
the declaration is u32, while the definition spells enum nl80211_he_gi.
Synchronize them to the latter.
Cc: Martin Liska <mliska@suse.cz>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221031114341.10377-1-jirislaby@kernel.org
During a nowait buffered write, if we fail to balance dirty pages we exit
btrfs_buffered_write() without releasing the delalloc space reserved for
an extent, resulting in leaking space from the inode's block reserve.
So fix that by releasing the delalloc space for the extent when balancing
dirty pages fails.
Reported-by: kernel test robot <yujie.liu@intel.com>
Link: https://lore.kernel.org/all/202210111304.d369bc32-yujie.liu@intel.com
Fixes: 965f47aeb5 ("btrfs: make btrfs_buffered_write nowait compatible")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we are doing a buffered write in NOWAIT context and we can't reserve
metadata space due to -ENOSPC, then we should return -EAGAIN so that we
retry the write in a context allowed to block and do metadata reservation
with flushing, which might succeed this time due to the allowed flushing.
Returning -ENOSPC while in NOWAIT context simply makes some writes fail
with -ENOSPC when they would likely succeed after switching from NOWAIT
context to blocking context. That is unexpected behaviour and even fio
complains about it with a warning like this:
fio: io_u error on file /mnt/sdi/task_0.0.0: No space left on device: write offset=1535705088, buflen=65536
fio: pid=592630, err=28/file:io_u.c:1846, func=io_u error, error=No space left on device
The fio's job config is this:
[global]
bs=64K
ioengine=io_uring
iodepth=1
size=2236962133
nr_files=1
filesize=2236962133
direct=0
runtime=10
fallocate=posix
io_size=2236962133
group_reporting
time_based
[task_0]
rw=randwrite
directory=/mnt/sdi
numjobs=4
So fix this by returning -EAGAIN if we are in NOWAIT context and the
metadata reservation failed with -ENOSPC.
Fixes: 304e45acdb ("btrfs: plumb NOWAIT through the write path")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Several places in the qgroup self tests follow the pattern of freeing the
ulist pointer they passed to btrfs_find_all_roots() if the call to that
function returned an error. That is pointless because that function always
frees the ulist in case it returns an error.
Also In some places like at test_multiple_refs(), after a call to
btrfs_qgroup_account_extent() we also leave "old_roots" and "new_roots"
pointing to ulists that were freed, because btrfs_qgroup_account_extent()
has freed those ulists, and if after that the next call to
btrfs_find_all_roots() fails, we call ulist_free() on the "old_roots"
ulist again, resulting in a double free.
So remove those calls to reduce the code size and avoid double ulist
free in case of an error.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the test_no_shared_qgroup() and test_multiple_refs() qgroup self tests,
if we fail to add the tree ref, remove the extent item or remove the
extent ref, we are returning from the test function without freeing the
"old_roots" ulist that was allocated by the previous calls to
btrfs_find_all_roots(). Fix that by calling ulist_free() before returning.
Fixes: 442244c963 ("btrfs: qgroup: Switch self test to extent-oriented qgroup mechanism.")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During backref walking, at find_parent_nodes(), if we are dealing with a
data extent and we get an error while resolving the indirect backrefs, at
resolve_indirect_refs(), or in the while loop that iterates over the refs
in the direct refs rbtree, we end up leaking the inode lists attached to
the direct refs we have in the direct refs rbtree that were not yet added
to the refs ulist passed as argument to find_parent_nodes(). Since they
were not yet added to the refs ulist and prelim_release() does not free
the lists, on error the caller can only free the lists attached to the
refs that were added to the refs ulist, all the remaining refs get their
inode lists never freed, therefore leaking their memory.
Fix this by having prelim_release() always free any attached inode list
to each ref found in the rbtree, and have find_parent_nodes() set the
ref's inode list to NULL once it transfers ownership of the inode list
to a ref added to the refs ulist passed to find_parent_nodes().
Fixes: 86d5f99442 ("btrfs: convert prelimary reference tracking to use rbtrees")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During backref walking, at resolve_indirect_refs(), if we get an error
we jump to the 'out' label and call ulist_free() on the 'parents' ulist,
which frees all the elements in the ulist - however that does not free
any inode lists that may be attached to elements, through the 'aux' field
of a ulist node, so we end up leaking lists if we have any attached to
the unodes.
Fix this by calling free_leaf_list() instead of ulist_free() when we exit
from resolve_indirect_refs(). The static function free_leaf_list() is
moved up for this to be possible and it's slightly simplified by removing
unnecessary code.
Fixes: 3301958b7c ("Btrfs: add inodes before dropping the extent lock in find_all_leafs")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Changed information about device removal in dmesg.
In function iavf_remove changed printed message from
"Remove" to "Removing" after hot vf plug/unplug.
Reason for this change is that, that "Removing" word
is better because it is clearer for the user that
the device is already being removed rather than implying
that the user should remove this device.
Signed-off-by: Bartosz Staszewski <bartoszx.staszewski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
__FUNCTION__ exists only for backwards compatibility reasons with old
gcc versions. Replace it with __func__.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Nothing logged in dmesg for attempting to set incorrect duplex.
Add appropriate error message logged for incorrect duplex setting.
Signed-off-by: Alicja Kowalska <alicjax.kowalska@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a tracepoint for i40e_napi_poll that allows users to get detailed
information about the amount of work done. This information can help users
better tune the correct NAPI parameters (like weight and budget), as well
as debug NIC settings like rx-usecs and tx-usecs, etc.
When perf is attached, this tracepoint only fires when not in XDP mode.
An example of the output from this tracepoint:
$ sudo perf trace -e i40e:i40e_napi_poll -a --call-graph=fp --libtraceevent_print
[..snip..]
388.258 :0/0 i40e:i40e_napi_poll(i40e_napi_poll on dev eth2 q i40e-eth2-TxRx-9 irq 346 irq_mask 00000000,00000000,00000000,00000000,00000000,00800000 curr_cpu 23 budget 64 bpr 64 rx_cleaned 28 tx_cleaned 0 rx_clean_complete 1 tx_clean_complete 1)
i40e_napi_poll ([i40e])
i40e_napi_poll ([i40e])
__napi_poll ([kernel.kallsyms])
net_rx_action ([kernel.kallsyms])
__do_softirq ([kernel.kallsyms])
common_interrupt ([kernel.kallsyms])
asm_common_interrupt ([kernel.kallsyms])
intel_idle_irq ([kernel.kallsyms])
cpuidle_enter_state ([kernel.kallsyms])
cpuidle_enter ([kernel.kallsyms])
do_idle ([kernel.kallsyms])
cpu_startup_entry ([kernel.kallsyms])
[0x243fd8] ([kernel.kallsyms])
secondary_startup_64_no_verify ([kernel.kallsyms])
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adjust i40e_clean_rx_irq to accept an out parameter which records the number of
RX packets cleaned.
No XDP related code is modified and care has been taken to avoid changing
control flow.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Merge series from cy_huang <u0084500@gmail.com>:
The RT6190 is a 4-switch Buck-Boost controller designed for USB power delivery
(USB PD). It operates with wide input voltage range from 4.5V to 36V, and the
output voltage can be programmable between 3V and 36V. It implements peak
current mode control mechanism to deliver up to 100W power with the
programmable constant voltage and constant current output. It also has built-in
charge pumps for driving external low-cost N-MOSFETs to control the power path.
Update i40e_clean_tx_irq to take an out parameter (tx_cleaned) which stores
the number TXs cleaned.
No XDP related TX code is touched. Care has been taken to avoid changing
the control flow of i40e_clean_tx_irq and i40e_napi_poll.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
