This patch add support for v1.7 SoundWire Controller which has
support for Multi-EE (Execution Environment), resulting in a
new register and extending field in BUS_CTRL register.
With these updates v1.7.0 is fully supported.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-7-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Some Qualcomm SOCs like sc8280xp which uses v1.6 soundwire controller
reset is not mandatory, so make this an optional one.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-5-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reading will increase the fifo count, so check for outstanding cmd wrt.
write fifo depth to avoid overflow as read will also increase
write fifo cnt.
Fixes: a661308c34 ("soundwire: qcom: wait for fifo space to be available before read/write")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some reason we never reinit the broadcast completion, there is a
danger that broadcast commands could be treated as completed by driver
from previous complete status.
Fix this by reinitializing the completion before sending a broadcast command.
Fixes: ddea6cf7b6 ("soundwire: qcom: update register read/write routine")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The bus->clk_stop_timeout member is only initialized to a non-zero value
during the codec driver probe. This can lead to corner cases where this
value remains pegged at zero when the bus suspends, which results in an
endless loop in sdw_bus_wait_for_clk_prep_deprep().
Corner cases include configurations with no codecs described in the
firmware, or delays in probing codec drivers.
Initializing the default timeout to the smallest non-zero value avoid this
problem and allows for the existing logic to be preserved: the
bus->clk_stop_timeout is set as the maximum required by all codecs
connected on the bus.
Fixes: 1f2dcf3a15 ("soundwire: intel: set dev_num_ida_min")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Following the clock rate range improvements to the clock framework,
trying to set a disjoint range on a clock will now result in an error.
Thus, we can't set a minimum rate higher than the maximum reported by
the firmware, or clk_set_min_rate() will fail.
Thus we need to clamp the rate we are about to ask for to the maximum
rate possible on that clock.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-7-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
At least the 4096x2160@60Hz mode requires some overclocking that isn't
available by default, even if hdmi_enable_4kp60 is enabled.
Let's add some logic to detect whether we can satisfy the core clock
requirements for that mode, and prevent it from being used otherwise.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-6-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
This will have the side-effect of raising the maximum of the core clock,
tied to the HVS, and managed by the HVS driver.
However, we are querying this in the HDMI driver by poking into the HVS
structure to get our struct clk handle.
Let's make this part of the HVS bind implementation to have all the core
clock related setup in the same place.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-5-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
We were detecting this so far by calling clk_round_rate() on the core
clock with the frequency we're supposed to run at when one of those
modes is enabled. Whether or not the parameter was enabled could then be
inferred by the returned rate since the maximum clock rate reported by
the firmware was one of the side effect of setting that parameter.
However, the recent clock rework we did changed what clk_round_rate()
was returning to always return the minimum allowed, and thus this test
wasn't reliable anymore.
Let's use the new clk_get_max_rate() function to reliably determine the
maximum rate allowed on that clock and fix the 4k@60Hz output.
Fixes: e9d6cea2af ("clk: bcm: rpi: Run some clocks at the minimum rate allowed")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-4-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The firmware allows to query for its clocks the operating range of a
given clock. We'll need this for some drivers (KMS, in particular) to
infer the state of some configuration options, so let's create a
function to do so.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-3-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need the clock IDs in more drivers than just the clock driver from
now on, so let's move them in the firmware header.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-2-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A significant number of RaspberryPi drivers using the firmware don't
have a phandle to it, so end up scanning the device tree to find a node
with the firmware compatible.
That code is duplicated everywhere, so let's introduce a helper instead.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-1-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Should not call eventfd_ctx_put() in case of error.
Fixes: 2fd6df2f2b ("KVM: x86/xen: intercept EVTCHNOP_send from guests")
Reported-by: syzbot+6f0c896c5a9449a10ded@syzkaller.appspotmail.com
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Message-Id: <20221028092631.117438-1-eiichi.tsukata@nutanix.com>
[Introduce new goto target instead. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dan reported that acl is dereferenced before being checked and this is a
valid problem. Fix it be erroring out early instead of doing it later after
we've already relied on acl to be a valid pointer.
Fixes: dc1af4c4b4 ("cifs: implement set acl method")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
In cap_inode_getsecurity(), we will use vfs_getxattr_alloc() to
complete the memory allocation of tmpbuf, if we have completed
the memory allocation of tmpbuf, but failed to call handler->get(...),
there will be a memleak in below logic:
|-- ret = (int)vfs_getxattr_alloc(mnt_userns, ...)
| /* ^^^ alloc for tmpbuf */
|-- value = krealloc(*xattr_value, error + 1, flags)
| /* ^^^ alloc memory */
|-- error = handler->get(handler, ...)
| /* error! */
|-- *xattr_value = value
| /* xattr_value is &tmpbuf (memory leak!) */
So we will try to free(tmpbuf) after vfs_getxattr_alloc() fails to fix it.
Cc: stable@vger.kernel.org
Fixes: 8db6c34f1d ("Introduce v3 namespaced file capabilities")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
[PM: subject line and backtrace tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Instead of generic description, mention what reset_lock actually
protects i.e. lock to serialize xmit and tx_timeout execution.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code provokes some kernel-doc warnings:
security/lsm_audit.c:198: warning: Function parameter or member
'ab' not described in 'dump_common_audit_data'
Signed-off-by: Bo Liu <liubo03@inspur.com>
[PM: description line wrap]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Because we enable the clock immediately after acquiring it in probe,
we can combine the 2 operations and use devm_clk_get_optional_enabled()
helper.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiawen Wu says:
====================
net: WangXun txgbe ethernet driver
This patch series adds support for WangXun 10 gigabit NIC, to initialize
hardware, set mac address, and register netdev.
Change log:
v6: address comments:
Jakub Kicinski: check with scripts/kernel-doc
v5: address comments:
Jakub Kicinski: clean build with W=1 C=1
v4: address comments:
Andrew Lunn: https://lore.kernel.org/all/YzXROBtztWopeeaA@lunn.ch/
v3: address comments:
Andrew Lunn: remove hw function ops, reorder functions, use BIT(n)
for register bit offset, move the same code of txgbe
and ngbe to libwx
v2: address comments:
Andrew Lunn: https://lore.kernel.org/netdev/YvRhld5rD%2FxgITEg@lunn.ch/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MAC address related operations, and register netdev.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset and initialize the hardware by configuring the MAC layer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get PCI config space info, set LAN id and check flash status.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64 bit host, if the guest doesn't have X86_FEATURE_LM, KVM will
access 16 gprs to 32-bit smram image, causing out-ouf-bound ram
access.
On 32 bit host, the rsm_load_state_64/enter_smm_save_state_64
is compiled out, thus access overflow can't happen.
Fixes: b443183a25 ("KVM: x86: Reduce the number of emulator GPRs to '8' for 32-bit KVM")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221025124741.228045-15-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the emulation mode when handling writes to CR0, because
toggling CR0.PE switches between Real and Protected Mode, and toggling
CR0.PG when EFER.LME=1 switches between Long and Protected Mode.
This is likely a benign bug because there is no writeback of state,
other than the RIP increment, and when toggling CR0.PE, the CPU has
to execute code from a very low memory address.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-14-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the emulation mode after RSM so that RIP will be correctly
written back, because the RSM instruction can switch the CPU mode from
32 bit (or less) to 64 bit.
This fixes a guest crash in case the #SMI is received while the guest
runs a code from an address > 32 bit.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-13-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some instructions update the cpu execution mode, which needs to update the
emulation mode.
Extract this code, and make assign_eip_far use it.
assign_eip_far now reads CS, instead of getting it via a parameter,
which is ok, because callers always assign CS to the same value
before calling this function.
No functional change is intended.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-12-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SYSEXIT is one of the instructions that can change the
processor mode, thus ctxt->mode should be updated after it.
Note that this is likely a benign bug, because the only problematic
mode change is from 32 bit to 64 bit which can lead to truncation of RIP,
and it is not possible to do with sysexit,
since sysexit running in 32 bit mode will be limited to 32 bit version.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221025124741.228045-11-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tag "guest_saw_irq" as "volatile" to ensure that the compiler will never
optimize away lookups. Relying on the compiler thinking that the flag
is global and thus might change also works, but it's subtle, less robust,
and looks like a bug at first glance, e.g. risks being "fixed" and
breaking the test.
Make the flag "static" as well since convincing the compiler it's global
is no longer necessary.
Alternatively, the flag could be accessed with {READ,WRITE}_ONCE(), but
literally every access would need the wrappers, and eking out performance
isn't exactly top priority for selftests.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221013211234.1318131-17-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tests for races between shinfo_cache (de)activation and hypercall+ioctl()
processing. KVM has had bugs where activating the shared info cache
multiple times and/or with concurrent users results in lock corruption,
NULL pointer dereferences, and other fun.
For the timer injection testcase (#22), re-arm the timer until the IRQ
is successfully injected. If the timer expires while the shared info
is deactivated (invalid), KVM will drop the event.
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221013211234.1318131-16-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Mubashir Adnan Qureshi says:
====================
net: Add PLB functionality to TCP
This patch series adds PLB (Protective Load Balancing) to TCP and hooks
it up to DCTCP. PLB is disabled by default and can be enabled using
relevant sysctls and support from underlying CC.
PLB (Protective Load Balancing) is a host based mechanism for load
balancing across switch links. It leverages congestion signals(e.g. ECN)
from transport layer to randomly change the path of the connection
experiencing congestion. PLB changes the path of the connection by
changing the outgoing IPv6 flow label for IPv6 connections (implemented
in Linux by calling sk_rethink_txhash()). Because of this implementation
mechanism, PLB can currently only work for IPv6 traffic. For more
information, see the SIGCOMM 2022 paper:
https://doi.org/10.1145/3544216.3544226
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rcv_wnd can be useful to diagnose TCP performance where receiver window
becomes the bottleneck. rehash reports the PLB and timeout triggered
rehash attempts by the TCP connection.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A u32 counter is added to tcp_sock for counting the number of PLB
triggered rehashes for a TCP connection. An SNMP counter is also
added to count overall PLB triggered rehash events for a host. These
counters are hooked up to PLB implementation for DCTCP.
TCP_NLA_REHASH is added to SCM_TIMESTAMPING_OPT_STATS that reports
the rehash attempts triggered due to PLB or timeouts. This gives
a historical view of sustained congestion or timeouts experienced
by the TCP connection.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLB support is added to TCP DCTCP code. As DCTCP uses ECN as the
congestion signal, PLB also uses ECN to make decisions whether to change
the path or not upon sustained congestion.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Congestion control algorithms track PLB state and cause the connection
to trigger a path change when either of the 2 conditions is satisfied:
- No packets are in flight and (# consecutive congested rounds >=
sysctl_tcp_plb_idle_rehash_rounds)
- (# consecutive congested rounds >= sysctl_tcp_plb_rehash_rounds)
A round (RTT) is marked as congested when congestion signal
(ECN ce_ratio) over an RTT is greater than sysctl_tcp_plb_cong_thresh.
In the event of RTO, PLB (via tcp_write_timeout()) triggers a path
change and disables congestion-triggered path changes for random time
between (sysctl_tcp_plb_suspend_rto_sec, 2*sysctl_tcp_plb_suspend_rto_sec)
to avoid hopping onto the "connectivity blackhole". RTO-triggered
path changes can still happen during this cool-off period.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLB (Protective Load Balancing) is a host based mechanism for load
balancing across switch links. It leverages congestion signals(e.g. ECN)
from transport layer to randomly change the path of the connection
experiencing congestion. PLB changes the path of the connection by
changing the outgoing IPv6 flow label for IPv6 connections (implemented
in Linux by calling sk_rethink_txhash()). Because of this implementation
mechanism, PLB can currently only work for IPv6 traffic. For more
information, see the SIGCOMM 2022 paper:
https://doi.org/10.1145/3544216.3544226
This commit adds new sysctl knobs and sets their default values for
TCP PLB.
Signed-off-by: Mubashir Adnan Qureshi <mubashirq@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a limit to eDMA AXI on i.MX93. Only TCD that has NBYTES in a
multiple of 8bytes can enable scatter-gather. NBYTES is calculated by
bus width times maxburst. On i.MX93 platform the value of maxburst is
specified to 8. It makes sure that NBYTES is a multiple of 8bytes.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221027060311.2549711-4-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string and specific soc data to support SAI on i.MX93
platform.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221027060311.2549711-3-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string "fsl,imx93-sai" for i.MX93 platform
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221027060311.2549711-2-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Raju Lakkaraju says:
====================
net: phy: mxl-gpy: Add MDI-X
This patch series add the MDI-X feature to GPY211 PHYs and
Also Change return type to gpy_update_interface() function
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration for GPY211 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gpy_update_interface() is called from gpy_read_status() which does
return error codes. gpy_read_status() would benefit from returning
-EINVAL, etc.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix minor nits from the last review round: extra {}, temporary
variables for ARRAYS_SIZE(), redundant check in ov4689_check_hwcfg.
No functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Now that we have a good way to specify dependency of tests on programs,
convert some of the tracer tests to use this method for specifying
dependency on 'chrt'.
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
All these tests depend on the ping command and will fail if it is not
found. Allow tests to specify dependencies on programs through the
'requires' field. Add dependency on 'ping' for some of the trigger
tests.
Link: https://lore.kernel.org/all/20221017104312.16af5467@gandalf.local.home/
Reported-by: Akanksha J N <akanksha@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
After reworking posix acls this helper isn't used anywhere outside the core
posix acl paths. Make it static.
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
