The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The phy-armada375-usb2 driver uses IOMEM functions so COMPILE_TEST && OF
build failed with:
drivers/built-in.o: In function `armada375_usb_phy_probe':
phy-armada375-usb2.c:(.text+0x121d): undefined reference to
`devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the related driver (CPG/MSSR driver) only manages the first module
clock, this driver should not handle the HSUSB registers. So, this patch
removes the HSUSB registers handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Most newer Rockchip SoCs provide the possibility to use a usb-phy
as passthrough for the debug uart (uart2), making it possible to
for example get console output without needing to open the device.
This patch adds an early_initcall to enable this functionality
conditionally via the commandline and also disables the corresponding
usb controller in the devicetree.
Currently only data for the rk3288 is provided, but at least the
rk3188 and arm64 rk3368 also provide this functionality and will be
enabled later.
On a spliced usb cable the signals are tx on white wire(D+) and
rx on green wire(D-).
The one caveat is that currently the reconfiguration of the phy
happens as early_initcall, as the code depends on the unflattened
devicetree being available. Everything is fine if only a regular
console is active as the console-replay will happen after the
reconfiguation. But with earlycon active output up to smp-init
currently will get lost.
The phy is an optional property for the connected dwc2 controller,
so we still provide the phy device but fail all phy-ops with -EBUSY
to make sure the dwc2 does not try to transmit anything on the
repurposed phy.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add dt binding documentation for rockchip display port PHY.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add phy driver for the Rockchip DisplayPort PHY module. This
is required to get DisplayPort working in Rockchip SoCs.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to add a generic PHY driver for ROCKCHIP eMMC PHY.
Access the PHY via registers provided by GRF (general register
files) module.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a binding that describes the Rockchip eMMC PHYs
found on Rockchip SoCs eMMC interface.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The function can return negative value so it should be assigned to signed
variable. The patch changes also type of related i variable to make code
more compact and coherent.
The problem has been detected using patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This makes a number of cleanups to handling of mapping failures during
memory hotplug on Power:
For errors creating the linear mapping for the hot-added region:
* This is now reported with EFAULT which is more appropriate than the
previous EINVAL (the failure is unlikely to be related to the
function's parameters)
* An error in this path now prints a warning message, rather than just
silently failing to add the extra memory.
* Previously a failure here could result in the region being partially
mapped. We now clean up any partial mapping before failing.
For errors creating the vmemmap for the hot-added region:
* This is now reported with EFAULT instead of causing a BUG() - this
could happen for external reason (e.g. full hash table) so it's better
to handle this non-fatally
* An error message is also printed, so the failure won't be silent
* As above a failure could cause a partially mapped region, we now
clean this up. [mpe: move htab_remove_mapping() out of #ifdef
CONFIG_MEMORY_HOTPLUG to enable this]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment the hpte_removebolted callback in ppc_md returns void and
will BUG_ON() if the hpte it's asked to remove doesn't exist in the first
place. This is awkward for the case of cleaning up a mapping which was
partially made before failing.
So, we add a return value to hpte_removebolted, and have it return ENOENT
in the case that the HPTE to remove didn't exist in the first place.
In the (sole) caller, we propagate errors in hpte_removebolted to its
caller to handle. However, we handle ENOENT specially, continuing to
complete the unmapping over the specified range before returning the error
to the caller.
This means that htab_remove_mapping() will work sanely on a partially
present mapping, removing any HPTEs which are present, while also returning
ENOENT to its caller in case it's important there.
There are two callers of htab_remove_mapping():
- In remove_section_mapping() we already WARN_ON() any error return,
which is reasonable - in this case the mapping should be fully
present
- In vmemmap_remove_mapping() we BUG_ON() any error. We change that to
just a WARN_ON() in the case of ENOENT, since failing to remove a
mapping that wasn't there in the first place probably shouldn't be
fatal.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the only error that htab_remove_mapping() can report is -EINVAL,
if removal of bolted HPTEs isn't implemeted for this platform. We make
a few clean ups to the handling of this:
* EINVAL isn't really the right code - there's nothing wrong with the
function's arguments - use ENODEV instead
* We were also printing a warning message, but that's a decision better
left up to the callers, so remove it
* One caller is vmemmap_remove_mapping(), which will just BUG_ON() on
error, making the warning message redundant, so no change is needed
there.
* The other caller is remove_section_mapping(). This is called in the
memory hot remove path at a point after vmemmap_remove_mapping() so
if hpte_removebolted isn't implemented, we'd expect to have already
BUG()ed anyway. Put a WARN_ON() here, in lieu of a printk() since this
really shouldn't be happening.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
linux/string.h should be #included in module_signing.c to get memcpy(),
lest the following occur:
kernel/module_signing.c: In function 'mod_verify_sig':
kernel/module_signing.c:57:2: error: implicit declaration of function 'memcpy' [-Werror=implicit-function-declaration]
memcpy(&ms, mod + (modlen - sizeof(ms)), sizeof(ms));
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
This reverts commit 0b2b093ad4.
Turns out the MOXA vendor driver was basically just a copy of the
ti_usb_3410_5052 driver. We don't want two drivers for the same chip
even if mxu11x0 had gotten some much needed clean up before merge. So
let's remove the mxu11x0 driver, add support for these Moxa devices to
the TI driver, and then clean that driver up instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.
It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.
There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
hdmi_find_pcm_slot return -EBUSY when not no pcm slot found,
not -ENODEV. So the caller should compare with -EBUSY.
Fixes: a76056f2e5 ('ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug')
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After adding cpufreq-dt support to Exynos542x, the Odroid XU3-Lite can
be easily overheated when launching eight CPU-intensive tasks:
thermal thermal_zone3: critical temperature reached(121 C),shutting down
This seems to be specific to Odroid XU3-Lite board which officially
supports lower frequencies than regular XU3 or XU4. When working at
maximum CPU speed (1800 MHz big and 1300 MHz LITTLE) in warmer place for
longer time, the fan fails to cool down the board and it reaches
critical temperature.
Add CPU cooling to Exynos5422/5800 to fix this issue. When reaching last
interrupt-driven trip-point (70 degrees of Celsius) start passive
cooling in polling mode (slowing CPU by 2 steps). When reaching 85
degrees of Celsius, start slowing even more, down to 600 MHz.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
On Exynos5422 and Exynos5800 we support 12 cpufreq steps (200-1300 MHz) for LITTLE
and 18 steps for big core (200-1700 MHz). Add respective cooling cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
On Exynos5420 we support 8 cpufreq steps (600-1300 MHz) for LITTLE and
12 steps for big core (700-1800 MHz). Add respective cooling cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add hwmod data for the eDMA blocks:
- TPCC: Third-party channel controller
- TPTC0: Third-party transfer controller 0
- TPTC1: Third-party transfer controller 1
The TPCC's clock gating status follows the status of its clock and
power domain. This means that the hwmod code can not directly control
the TPCC enable/disable status.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: rephrased last two sentences of the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Exynos7 based espresso board uses S2MPS15, a multifunction device.
This patch enables S2MPS1X regulator, pmic-clk and rtc drivers utilized by
the same.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Instead of defining a local version of struct udphdr use the standard
definition from <linux/udp.h>.
The 'src' field is named 'source' in the <linux/udp.h> definition.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of defining a local version of struct iphdr use the standard
definition from <linux/ip.h>.
Several fields in the <linux/ip.h> definition have different names:
- proto -> protocol
- src -> saddr
- dest -> daddr
- total_length -> tot_len
- checksum -> check
Also, 'ver_len' is composed by 'version' and 'ihl' in <linux/ip.h>.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of defining the local struct vlantag use the standard definition
of vlan_hdr from <linux/if_vlan.h>.
The fields in the <linux/if_vlan.h> definition have different names:
- vlan -> h_vlan_TCI
- subtype -> h_vlan_encapsulated_proto
While there, use also the ETH_P_IP macro instead of an hard-coded 0x0800
value.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of defining a local version of struct ethhdr use the standard
definition from <linux/if_ether.h>.
The fields in the <linux/if_ether.h> definition have different names:
- dest -> h_dest
- src -> h_source
- type -> h_proto
While there, use a few other standard functions/macros:
- eth_broadcast_addr (instead of a memset)
- ETH_ALEN
- ETH_P_8021Q
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The vblank IRQ is only needed to trigger page flip work, so we
might as well disable it when there is no work to do.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If the FB is backed by a GEM object with an dma-buf attached
we need to wait for any pending fences to signal before executing
the page flip.
The implementation is straight forward by deferring the flip to
a workqueue in that case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The DRM core only references the currently queued/active framebuffer.
So there is a period of time where the flip is not completed, but
the GEM object backing the FB is already unreferenced and could be
destroyed if userspace closes its handle.
Make sure to keep a reference to the GEM object until the flip is
actually executed clean things up in a worker running behind the
flip execution.
Also move the page flip event into the context of this worker, so
it gets cleaned up automatically.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Start tracking the flip state explicitly, as opposed to inferring
it from the presence if a new FB. This is a preparatory step to
introduce an new immediate state, where we can wait for a fence to
signal.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The core already does the correct replacemet if the driver
page flip function returns without an error, so there is no
need to do it here.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch changes the dev_info() call to dev_dbg() in ipu_plane_update()
to print out the information that a plane's CRTC is changed, because this
kind of information is only useful for debugging.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This cleans up the display controller microcode setup in ipu_dc_init_sync
a little bit. The microcode template words for DI0 and DI1 are properly
separated to avoid a clash when DI1 is active in interlaced mode at the
same time as DI0 in non-interlaced mode.
A comment is added to explain the meaning of the sync counter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
It is replaced by drm_of_encoder_active_endpoint_id.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Yakir Yang <ykk@rock-chips.com>
[for dw_hdmi-rockchip]
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
It is replaced by drm_of_encoder_active_port_id.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Like a signal return, we should use synchronize_user_stack() rather
than flush_user_windows().
Reported-by: Ilya Malakhov <ilmalakhovthefirst@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binutils used to be (erroneously) extremely permissive about
instruction usage. But that got fixed and if you don't properly tell
it to accept classes of instructions it will fail.
This uncovered a specs bug on sparc in gcc where it wouldn't pass the
proper options to binutils options.
Deal with this in the kernel build by adding -Wa,-Av8 to KBUILD_CFLAGS.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the TRM says, add the tsadc_q_sel to control the temperature-code
sequence since the rk3228/rk3399 need set this bit (1024 - tsadc_q)
as output.
Fixes: commit
b0d7033 "thermal: rockchip: Support the RK3399 SoCs in thermal driver"
7b02a5e "thermal: rockchip: Support the RK3228 SoCs in thermal driver"
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch renames to be more adapter compatibles since more and more
SoCs are supported in thermal driver.
Reported-by: Huang,Tao <huangtao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
the calculation use a global table, not their own table.
so adapt the table to the correct one.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the burst mode that will break DMA uart on SoCFPGA.
In some cases, some SoCS didn't support the multi-burst
even if the devices who use the pl330 claim support the maxburst.
Fixes: commit 848e977
"dmaengine: pl330: support burst mode for dev-to-mem and mem-to-dev transmit"
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The firmware ctls like "DSP1 Firmware" in wm_adsp codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Speaker Mode "ctl in wm9081 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DSP1 EQ Mode" and "DSP2 EQ Mode" ctls in wm8996 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in
wm8994 codec driver are enum ctls, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Equalizer Function" ctl in wm8985 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Equalizer Function" ctl in wm8983 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
