VFS uses a two-stage check-and-call method for invoking file_operations
methods, without explicitly snapshotting either the file_operations ptr
or the function ptr. Since the tty core is one of the few VFS users that
changes the f_op file_operations ptr of the file descriptor (when the
tty has been hung up), and since the likelihood of the compiler generating
a reload of either f_op or the function ptr is basically nil, just define
a hung up fasync() file operation that returns an error.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the N_TTY line discipline implements the signal-driven i/o
notification enabled/disabled by fcntl(F_SETFL, O_ASYNC). The ldisc
fasync() notification is sent to the ldisc when the enable state has
changed (the tty core is notified via the fasync() VFS file operation).
The N_TTY line discipline used the enable state to change the wakeup
condition (minimum_to_wake = 1) for notifying the signal handler i/o is
available. However, just the presence of data is sufficient and necessary
to signal i/o is available, so changing minimum_to_wake is unnecessary
(and creates a race condition with read() and poll() which may be
concurrently updating minimum_to_wake).
Furthermore, since the kill_fasync() VFS helper performs no action if
the fasync list is empty, calling unconditionally is preferred; if
signal driven i/o just has been disabled, no signal will be sent by
kill_fasync() anyway so notification of the change via the ldisc
fasync() method is superfluous.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read() in non-canonical mode when VMIN > 0 and VTIME == 0 does not
complete until at least VMIN chars have been read (or the user buffer is
full). In this infrequent read mode, n_tty_read() attempts to reduce
wakeups by computing the amount of data still necessary to complete the
read (minimum_to_wake) and only waking the read()/poll() when that much
unread data has been processed. This is the only read mode for which
new data does not necessarily generate a wakeup.
However, this optimization is broken and commonly leads to hung reads
even though the necessary amount of data has been received. Since the
optimization is of marginal value anyway, just remove the whole
thing. This also remedies a race between a concurrent poll() and
read() in this mode, where the poll() can reset the minimum_to_wake
of the read() (and vice versa).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between perf_event_exit_task_context() and
orphans_remove_work() which results in a use-after-free.
We mark ctx->task with TASK_TOMBSTONE to indicate a context is
'dead', under ctx->lock. After which point event_function_call()
on any event of that context will NOP
A concurrent orphans_remove_work() will only hold ctx->mutex for
the list iteration and not serialize against this. Therefore its
possible that orphans_remove_work()'s perf_remove_from_context()
call will fail, but we'll continue to free the event, with the
result of free'd memory still being on lists and everything.
Once perf_event_exit_task_context() gets around to acquiring
ctx->mutex it too will iterate the event list, encounter the
already free'd event and proceed to free it _again_. This fails
with the WARN in free_event().
Plug the race by having perf_event_exit_task_context() hold
ctx::mutex over the whole tear-down, thereby 'naturally'
serializing against all other sites, including the orphan work.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: alexander.shishkin@linux.intel.com
Cc: dsahern@gmail.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/20160125130954.GY6357@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should set event->owner before we install the event,
otherwise there is a hole where the target task can fork() and
we'll not inherit the event because it thinks the event is
orphaned.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The fb_modifiers and cpp arguments passed to intel_tile_width() in
intel_fill_fb_ggtt_view() got accidentally swapped around. I'm pretty
sure I fixed this already, but could be I lost the fix accidentally
during some rebases or something. Anyway, fix it up for real.
Fixes: d9b3288ecf ("drm/i915: change intel_fill_fb_ggtt_view() to use the real tile size")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-8-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_rotation_crc/primary-rotation-90
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
In the error-handling paths of i915_gem_do_execbuffer() and
intel_crtc_page_flip(), the local pointer-to-request variables
were expected to be either valid pointers or NULL. Since
2682708 drm/i915: simplify allocation of driver-internal requests
they could also be ERR_PTR() values, so the tests need to be
updated to accommodate this case.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453978089-29127-1-git-send-email-tvrtko.ursulin@linux.intel.com
In GuC mode LRC pinning lifetime depends exclusively on the
request liftime. Since that is terminated by the seqno update
that opens up a race condition between GPU finishing writing
out the context image and the driver unpinning the LRC.
To extend the LRC lifetime we will employ a similar approach
to what legacy ringbuffer submission does.
We will start tracking the last submitted context per engine
and keep it pinned until it is replaced by another one.
Note that the driver unload path is a bit fragile and could
benefit greatly from efforts to unify the legacy and exec
list submission code paths.
At the moment i915_gem_context_fini has special casing for the
two which are potentialy not needed, and also depends on
i915_gem_cleanup_ringbuffer running before itself.
v2:
* Move pinning into engine->emit_request and actually fix
the reference/unreference logic. (Chris Wilson)
* ring->dev can be NULL on driver unload so use a different
route towards it.
v3:
* Rebase.
* Handle the reset path. (Chris Wilson)
* Exclude default context from the pinning - it is impossible
to get it right before default context special casing in
general is eliminated.
v4:
* Rebased & moved context tracking to
intel_logical_ring_advance_and_submit.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Issue: VIZ-4277
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453976997-25424-1-git-send-email-tvrtko.ursulin@linux.intel.com
Will enable cleaner implementation of a following fix and
easier code unification in the future.
Idea and code by Chris Wilson.
v2: Do not return before last_contexts on engines are unpinned.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Will simplify the following fix and sounds logical.
v2: Add some whitespace to separate logic better. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Previously intel_lr_context_(un)pin were operating on requests
which is in conflict with their names.
If we make them take a context and an engine, it makes the names
make more sense and it also makes future fixes possible.
v2: Rebase for default_context/kernel_context change.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
mmc sample shift is 0 for rk3228 refer to user manaul.
So it's broken if we enable mmc tuning for rk3228.
Fixes: 307a2e9ac ("clk: rockchip: add clock controller for rk3228")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When using the ssi-protocol driver with the Nokia N950, the
following error is thrown during modem powered up sequence.
[13852.274993] port0: SSI error: 0x01
[13852.279205] ssi-protocol ssi-protocol: RX error detected
[13852.284820] ssi-protocol ssi-protocol: Main state: 1
[13852.290069] ssi-protocol ssi-protocol: Recv state: 0
[13852.295288] ssi-protocol ssi-protocol: Send state: 0
[13852.300537] ssi-protocol ssi-protocol: CMT Offline
[13852.305603] ssi-protocol ssi-protocol: Wake test 1
[13852.310638] ssi-protocol ssi-protocol: Data RX id: 0
[13852.315887] ssi-protocol ssi-protocol: Data TX id: 0
[13856.001464] ssi-protocol ssi-protocol: Watchdog trigerred
[13856.007293] ssi-protocol ssi-protocol: Main state: 1
[13856.012542] ssi-protocol ssi-protocol: Recv state: 0
[13856.017761] ssi-protocol ssi-protocol: Send state: 0
[13856.023010] ssi-protocol ssi-protocol: CMT Offline
[13856.028045] ssi-protocol ssi-protocol: Wake test 0
[13856.033111] ssi-protocol ssi-protocol: Data RX id: 0
[13856.038330] ssi-protocol ssi-protocol: Data TX id: 0
This patch fixes the issue by using the handshake setup from
the Nokia N950 kernel. The new handshake sequence also works
with the N900, so there is no need to differentiate between
both modems.
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This fixes a race condition in the error case: since the pt bos have not
necessarily been reserved in case of an error, we could move a pt bo that
is currently in the middle of being evicted/moved by another process,
which then resulted in a BUG_ON in ttm_bo_add_to_lru.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Nokia N950 and Nokia N9 also have a SSI connected
modem, which use the same protocols as the Nokia N900,
but with increased link speed (96000 kbps instead of
55000 kbps) and with less GPIOs.
Since it's unclear, if the N950 and the N9 use exactly
the same modem, each of them gets their own compatible
string.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SxKT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc2
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Compiler warns us a lot that it can't find include folder because it's
provided in relative form.
CC security/selinux/netlabel.o
cc1: warning: security/selinux/include: No such file or directory
cc1: warning: security/selinux/include: No such file or directory
cc1: warning: security/selinux/include: No such file or directory
cc1: warning: security/selinux/include: No such file or directory
Add $(srctree) prefix to the path.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[PM: minor description edits to fit under 80char width]
Signed-off-by: Paul Moore <paul@paul-moore.com>
hidpp_ff_init() and hidpp_ff_deinit() are not used outside of
hid-logitech-hidpp.c, so let's make them static.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements force feedback support for the Logitech
G920 Driving Force Racing Wheel. It is a generic implementation
of feature 0x8123 of the Logitech HID++ protocol and should be
usable for any future devices that implement this feature.
This patch should be applied after the basic G920 support patch
by Simon Wood:
http://www.spinics.net/lists/linux-input/msg42174.html
The driving supports everything that is supported by the G920
firmware:
FF_CONSTANT
FF_PERIODIC
FF_SINE
FF_SQUARE
FF_SAW_UP
FF_SAW_DOWN
FF_TRIANGLE
FF_SPRING
FF_DAMPER
FF_AUTOCENTER
FF_GAIN
and for version 2 firmware also:
FF_FRICTION
FF_INERTIA
FF_RAMP
Both envelopes and replay values are supported as well, but some
problems may occur when using firmware release 1. There is also a
small residual clockwise damper in the wheel when using the first
firmware release. All problems are fixed in the soon te be released
firmware version 2.
The default spring is disabled by permanently placing a spring
force in the wheel. This spring is also used as the autocenter
spring.
Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck
in XBox since the xpad changes where not included). Michal has an
alternative approach documented here (and the changes should be submitted
upstream to usb_modeswitch project):
===
Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the
following content:
DefaultVendor=046d
DefaultProduct=c261
MessageEndpoint=01
ResponseEndpoint=01
TargetClass=0x03
MessageContent="0f00010142"
Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and
watch the magic happen:)
===
[jkosina@suse.cz: added information about mode switching from Simon]
[jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon]
[jkosina@suse.cz: fix merge conflict due to to_hid_device() changes]
Signed-off-by: Edwin Velds <e.velds@gmail.com>
Tested-by: Elias Vanderstuyft <elias.vds@gmail.com>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_PINCTRL_SUNXI is more suitable than CONFIG_ARCH_SUNXI
to guard the drivers/pinctrl/sunxi/ directory.
(I renamed CONFIG_PINCTRL_SUNXI_COMMON to CONFIG_PINCTRL_SUNXI.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was wrongly updated by commit 7aa9a23c69 ("powerpc, thp: remove
infrastructure for handling splitting PMDs") during the last merge
window. Fix it up.
This could lead to incorrect behaviour in THP and/or mprotect(), at a
minimum.
Fixes: 7aa9a23c69 ("powerpc, thp: remove infrastructure for handling splitting PMDs")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 7a7868326d ("powerpc/perf: Add an explict flag indicating
presence of SLOT field") introduced the PPMU_HAS_SSLOT flag to remove
the assumption that MMCRA[SLOT] was present when PPMU_ALT_SIPR was not
set.
That commit's changelog also mentions that Power8 does not support
MMCRA[SLOT]. However when the Power8 PMU support was merged, it
errnoeously included the PPMU_HAS_SSLOT flag.
So remove PPMU_HAS_SSLOT from the Power8 flags.
mpe: On systems where MMCRA[SLOT] exists, the field occupies bits 37:39
(IBM numbering). On Power8 bit 37 is reserved, and 38:39 overlap with
the high bits of the Threshold Event Counter Mantissa. I am not aware of
any published events which use the threshold counting mechanism, which
would cause the mantissa bits to be set. So in practice this bug is
unlikely to trigger.
Fixes: e05b9b9e5c ("powerpc/perf: Power8 PMU support")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for restoring GScaler parent clocks configuration when GSCL
power domain is turned on.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Remove an unnecassary cast in the argument to kfree.
Found using Coccinelle. The semantic patch used to find this is as follows:
//<smpl>
@@
type T;
expression *f;
@@
- kfree((T *)(f));
+ kfree(f);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
amdgpu_amdkfd_gfx_7_get_functions and amdgpu_amdkfd_gfx_8_0_get_functions
have no parameters, so use the normal void parameter convention to make
them match their prototypes in the header file
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.h
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The STn8815 has 22 dedicated pins for CLCD with up to 16 bits
in parallel, but pins 32 thru 39 can be used for an additional
CLCD signal lines 16 thru 23.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No other kernel installation target moves the target directory out of
the way, even deleting an old version of it. These are destructive
operations, ones which the kernel build system should not be making.
This behaviour prevents being able to do:
make install INSTALL_PATH=/some/path/boot
make dtbs_install INSTALL_DTBS_PATH=/some/path/boot
As it causes the boot directory containing the kernel installed in
step 1 to be moved to /some/path/boot.old. Things get even more fun
if you do:
make install dtbs_install INSTALL_PATH=/some/path/boot INSTALL_DTBS_PATH=/some/path/boot
The kernel gets installed into /some/path/boot, then the directory gets
renamed to /some/path/boot.old, and a new directory created to hold the
dtbs. Even more fun if you supply -j2 when we end up with races in
make.
Remove this behaviour.
If this behaviour is required at installation time, this should be
done by the installation external to the kernel makefiles, just like
it would be done for 'make modules_install'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Marek <mmarek@suse.com>
The nomadik pinctrl driver has two functions that are only used
for debugfs output and are otherwise unused:
drivers/pinctrl/nomadik/pinctrl-abx500.c:194:12: error: 'abx500_get_pull_updown' defined but not used
drivers/pinctrl/nomadik/pinctrl-abx500.c:471:12: error: 'abx500_get_mode' defined but not used
This makes the function definitions conditional to avoid the
harmless warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix CPU operating points for Exynos5800 (it use different
voltages than Exynos5420 and supports additional frequencies).
However don't use 2000MHz & 1900MHz OPPs (for A15 cores) and
1400MHz OPP (for A7 cores) for now as they are not available
on all boards.
Based on Hardkernel's kernel for ODROID-XU3 board.
Changes by Ben Gamari:
- Port to operating-points-v2
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For Exynos542x/5800 platforms, add CPU operating points
for migrating from Exynos specific cpufreq driver to using
generic cpufreq driver.
Changes by Bartlomiej:
- split Exynos5420 support from the original patch
- merged Exynos5422 fixes from Ben
Changes by Ben Gamari:
- Port to operating-points-v2
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add cluster regulator supply properties as a preparation to
adding generic cpufreq-dt driver support for Exynos542x and
Exynos5800 based boards.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Exynos5420 and Exynos5800 boards boot from big core (A15) but
Exynos5422 boards choose otherwise: LITTLE core (A7) (on Exynos5422 this
is property of the board - configurable by pulling up/down gpg2-1).
To make user-visible CPU ordering more consistent the 'cpus' node was
overridden by exynos5422-cpus.dtsi.
However this is a little bit ugly and error-prone. Overriding the CPU
child nodes requires to basically reverse what was done initially in
exynos5420.dtsi.
Instead, split CPU configuration entirely to separate files which should
be included by board DTS.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanho Park <parkch98@gmail.com>
This got broken in:
commit de1add3605
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Fri Jan 15 15:12:50 2016 +0000
drm/i915: Decouple execbuf uAPI from internal implementation
BSD ring flags need to be shifted before they can be considered
indices into the ring array.
Reported by Zhipeng Gong.
v2: Simplify the code. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1453902069-31353-1-git-send-email-tvrtko.ursulin@linux.intel.com
Testcase: igt/gem_exec_basic # bdw-gt3
CONFIG_PINCTRL_PXA is more suitable than CONFIG_ARCH_PXA
to guard the drivers/pinctrl/pxa/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add mt2701 support using mediatek common pinctrl driver.
MT2701 have some special pins need an extra setting register
than other ICs, so adding this support to common code.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We dereference "eaction->event" inside the call to drm_send_event_locked()
so should hold off on setting it to NULL until afterward.
Fixes: fb740cf249 ("drm: Create drm_send_event helpers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160128090646.GA5824@mwanda
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I think this limit was added when CSA with multiple interfaces wasn't
working yet. It should no longer be necessary
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add F81866 GPIO supports
Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.
Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
The control method is the same with F7188x, but we should care the address
of GPIO8x.
GPIO address is below:
GPIO0x based: 0xf0
GPIO1x based: 0xe0
GPIO2x based: 0xd0
GPIO3x based: 0xc0
GPIO4x based: 0xb0
GPIO5x based: 0xa0
GPIO6x based: 0x90
GPIO7x based: 0x80
GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt-parent property is not needed as it is inherited from
the parent bus and in the case of the CAAM node actively points to
the wrong interrupt controller (GIC instead of GPC). This leads to
the CAAM IRQs not getting unmasked at the GPC level, leaving them
unable to wake the CPU from wait mode, potentially impacting
performance of the CAAM unit when CPUidle is enabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like how pci.c exposes hif ops for the bus specific operation,
expose similar hif ops table for ahb with all required functions
linked to it. Many ath10k_pci_* functions are reused here in hif ops
table. If something is not sharable, new functions are added for ahb
and linked to hif ops table.
Finally, make ath10k_ahb_probe/remove() to perform what is expected
out of it.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add function to gather resources required for qca4019 to operate
(memory, irq, dma setting, clock init , rest control init) and
function release those resources when it's not needed.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
