IRQ probing needs to know that the TPM is working before trying to
probe, so move tpm_get_timeouts() to the top of the tpm_tis_init().
This has the advantage of also getting the correct timeouts loaded
before doing IRQ probing.
All the timeout handling code is moved to tpm_get_timeouts() in order to
remove duplicate code in tpm_tis and tpm_crb.
[jarkko.sakkinen@linux.intel.com: squashed two patches together and
improved the commit message.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This should be done very early, before anything could possibly
cause the TPM to generate an interrupt. If the IRQ line is shared
with another driver causing an interrupt before setting up our
handler will be very bad.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The interrupt is always allocated with devm_request_irq so it
must always be freed with devm_free_irq.
Fixes: 448e9c55c1 ("tpm_tis: verify interrupt during init")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF.
Signed-off-by: Luka Karinja <luka.karinja@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transport will need to use the info->driver_data
pointers. Since the op_mode has this memory hot in cache,
clear it there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The code that handles the TBs that contain the WiFi payload
will be changed for TSO. Move the current code into a
separate function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Differentiate between the cases where the skb is a large
send and the other cases.
Advertise TSO even if, at this stage, skb_gso_segment will
be called and it will do all the work.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
After commit 739ae3452d ("phy: berlin-usb: Set drvdata for phy and
use it"), we get the address of priv by phy_get_drvdata(), so there's
no need to set device's driver_data any more. This patch removes the
call of platform_set_drvdata().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We don't need gpio related header files, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-sata-phy", may be used for
most MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add data for phy version, and the default value of version is using the
BRCM_SATA_PHY_28NM.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
While reviewing Michael Kerrisk's recent futex manpage update, I noticed
that we allow the FUTEX_CLOCK_REALTIME flag for FUTEX_WAIT_BITSET but
not for FUTEX_WAIT.
FUTEX_WAIT is treated as a simple version for FUTEX_WAIT_BITSET
internally (with a bitmask of FUTEX_BITSET_MATCH_ANY). As such, I cannot
come up with a reason for this exclusion for FUTEX_WAIT.
This change does modify the behavior of the futex syscall, changing a
call with FUTEX_WAIT | FUTEX_CLOCK_REALTIME from returning -ENOSYS, to be
equivalent to FUTEX_WAIT_BITSET | FUTEX_CLOCK_REALTIME with a bitset of
FUTEX_BITSET_MATCH_ANY.
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Link: http://lkml.kernel.org/r/9f3bdc116d79d23f5ee72ceb9a2a857f5ff8fa29.1450474525.git.dvhart@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
out_unlock: does not only drop the locks, it also drops the refcount
on the pi_state. Really intuitive.
Move the label after the put_pi_state() call and use 'break' in the
error handling path of the requeue loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.526665141@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the error handling cases we neither have pi_state nor a reference
to it. Remove the pointless code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.432780944@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Documentation of the pi_state refcounting in the requeue code is non
existent. Add it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.335938312@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
free_pi_state() is confusing as it is in fact only freeing/caching the
pi state when the last reference is gone. Rename it to put_pi_state()
which reflects better what it is doing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.259636467@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the proxy lock in the requeue loop acquires the rtmutex for a
waiter then it acquired also refcount on the pi_state related to the
futex, but the waiter side does not drop the reference count.
Add the missing free_pi_state() call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.178132067@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
The USB phys on Rockchip SoCs contain their own internal PLLs to create
the 480MHz needed. Additionally this PLL output is also fed back into the
core clock-controller as possible source for clocks like the GPU or others.
Until now this was modelled incorrectly with a "virtual" factor clock in
the clock controller. The one big caveat is that if we turn off the usb phy
via the siddq signal, all analog components get turned off, including the
PLLs. It is therefore possible that a source clock gets disabled without
the clock driver ever knowing, possibly making the system hang.
Therefore register the phy-plls as real clocks that the clock driver can
then reference again normally, making the clock hirarchy finally reflect
the actual hardware.
The phy-ops get converted to simply turning that new clock on and off
which in turn controls the siddq signal of the phy.
Through this the driver gains handling for platform-specific data, to
handle the phy->clock name association.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We need custom handling for these two socs in the driver shortly,
so add the necessary compatible values to binding and driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This unclutters the loop in probe a lot and makes current (and future)
error handling easier to read.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This introduces a common struct that holds data belonging to
the umbrella device that contains all the phys and that we
want to use later.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the phy driver only gets the optional clock reference but
never puts it again, neither during error handling nor on remove.
Fix that by moving the clk_put to a devm-action that gets called at
the right time when all other devm actions are done.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support hi6220 use phy for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use of_match_node instead of calling of_device_is_compatible a ton of
times to get model specific config data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
calibrate HS slew rate and switch 100uA current to SSUSB
to improve HS eye diagram of HQA test.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
when use the default value 8 of RG_USB20_SQTH, the HS receiver
sensitivity test of HQA will fail, set it as 2 to fix up the
issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for runtime ID/VBUS pin detection if
the channel 0 of R-Car gen3 is used. So, we are able to use
the channel as both host and peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To use the channel 0 of R-Car gen3 as periperal mode, This patch changes
the mode to OTG instead of HOST. Then, this driver needs to set some
registers to enable host mode and detects ID pin and VBUS pin at
phy_init() timing.
For now, the channel 0 can be used as host mode only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for R-Car generation 3 USB2 PHY driver.
This SoC has 3 EHCI/OHCI channels, and the channel 0 is shared
with the HSUSB (USB2.0 peripheral) device. And each channel has
independent registers about the PHYs.
So, the purpose of this driver is:
1) initializes some registers of SoC specific to use the
{ehci,ohci}-platform driver.
2) detects id pin to select host or peripheral on the channel 0.
For now, this driver only supports 1) above.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We didn't check input_allocate_device() for failures so it could lead to
a NULL deref.
Fixes: 6b0f8f9c52 ('Input: add eGalaxTouch serial touchscreen driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patches moves the debugfs interface related register after
netdevice register. The function lowpan_dev_debugfs_init will use
"dev->name" which can be before register_netdevice a format string.
The function register_netdevice will evaluate the format string if
necessary and replace "dev->name" to the real interface name.
Reported-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here are some tty/serial driver fixes for 4.4-rc6 that resolve some
reported problems. All of these have been in linux-next. The details
are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZ19rAACgkQMUfUDdst+ykBQQCeKSU7YZFKPTEFbGKS2UfFgMJd
EokAoIJp4lXqhLHKtI7TNwVFlMQAaDYj
=2I3R
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty/serial driver fixes for 4.4-rc6 that resolve some
reported problems. All of these have been in linux-next. The details
are in the shortlog"
* tag 'tty-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix GPF in flush_to_ldisc()
serial: earlycon: Add missing spinlock initialization
serial: sh-sci: Fix length of scatterlist
n_tty: Fix poll() after buffer-limited eof push read
serial: 8250_uniphier: fix dl_read and dl_write functions
Here are some USB and PHY fixes for 4.4-rc6. All of them resolve some
reported problems. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZ1+CoACgkQMUfUDdst+yksSQCg1MuW8nVyz7eUHcZnd/r4dSPa
fy8An0J0aKi8IhUMSIAIFcoM4/40ulCE
=ycut
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.4-rc6. All of them resolve some
reported problems. Full details in the shortlog"
* tag 'usb-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: fix invalid memory access in hub_activate()
USB: ipaq.c: fix a timeout loop
phy: core: Get a refcount to phy in devm_of_phy_get_by_index()
phy: cygnus: pcie: add missing of_node_put
phy: miphy365x: add missing of_node_put
phy: miphy28lp: add missing of_node_put
phy: rockchip-usb: add missing of_node_put
phy: berlin-sata: add missing of_node_put
phy: mt65xx-usb3: add missing of_node_put
phy: brcmstb-sata: add missing of_node_put
phy: sun9i-usb: add USB dependency
- 2 recently introduced regressions fixed.
- one older bug in RAID10 - tagged for -stable since 4.2
- one minor sysfs api improvement.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nHNn
-----END PGP SIGNATURE-----
Merge tag 'md/4.4-rc5-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Four fixes for md:
- two recently introduced regressions fixed.
- one older bug in RAID10 - tagged for -stable since 4.2
- one minor sysfs api improvement"
* tag 'md/4.4-rc5-fixes' of git://neil.brown.name/md:
Fix remove_and_add_spares removes drive added as spare in slot_store
md: fix bug due to nested suspend
MD: change journal disk role to disk 0
md/raid10: fix data corruption and crash during resync
- Partial revert of "powerpc: Individual System V IPC system calls"
- pr_warn_once on unsupported OPAL_MSG type from Stewart
- Fix deadlock in opal-irqchip introduced by "Fix double endian conversion" from Alistair
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=58wA
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Partial revert of "powerpc: Individual System V IPC system calls"
- pr_warn_once on unsupported OPAL_MSG type from Stewart
- Fix deadlock in opal-irqchip introduced by "Fix double endian
conversion" from Alistair
* tag 'powerpc-4.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/opal-irqchip: Fix deadlock introduced by "Fix double endian conversion"
powerpc/powernv: pr_warn_once on unsupported OPAL_MSG type
Partial revert of "powerpc: Individual System V IPC system calls"
just one regression fix.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: atomic check only enabled crtc states
Adding the rtc platform device in non-privileged Xen PV guests causes
an IRQ conflict because these guests do not have legacy PIC and may
allocate irqs in the legacy range.
In a single VCPU Xen PV guest we should have:
/proc/interrupts:
CPU0
0: 4934 xen-percpu-virq timer0
1: 0 xen-percpu-ipi spinlock0
2: 0 xen-percpu-ipi resched0
3: 0 xen-percpu-ipi callfunc0
4: 0 xen-percpu-virq debug0
5: 0 xen-percpu-ipi callfuncsingle0
6: 0 xen-percpu-ipi irqwork0
7: 321 xen-dyn-event xenbus
8: 90 xen-dyn-event hvc_console
...
But hvc_console cannot get its interrupt because it is already in use
by rtc0 and the console does not work.
genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (rtc0)
We can avoid this problem by realizing that unprivileged PV guests (both
Xen and lguests) are not supposed to have rtc_cmos device and so
adding it is not necessary.
Privileged guests (i.e. Xen's dom0) do use it but they should not have
irq conflicts since they allocate irqs above legacy range (above
gsi_top, in fact).
Instead of explicitly testing whether the guest is privileged we can
extend pv_info structure to include information about guest's RTC
support.
Reported-and-tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: vkuznets@redhat.com
Cc: xen-devel@lists.xenproject.org
Cc: konrad.wilk@oracle.com
Cc: stable@vger.kernel.org # 4.2+
Link: http://lkml.kernel.org/r/1449842873-2613-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
because the kobject API can do that for us - Rasmus Villemoes
* Update the arm64 file paths in Documentation/efi-stub.txt to match
the current tree - Alan Ott
* Consistently preface all print statements with "efi" arch/x86 so
that it's more obvious to users reporting problems which statements
in the kernel log are relevant for EFI - Matt Fleming
* Fix a boot crash in the ACPI BGRT driver and delete
efi_lookup_mapped_addr() since it's useless now that the EFI
mappings *only* exist in the 'efi_pgd' page table. Instead we
always early_memremap() the BGRT memory - Sai Praneeth Prakhya
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VYPl
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull efi changes from Matt Fleming:
* We don't need to carry our own formatting code in the esrt driver
because the kobject API can do that for us - Rasmus Villemoes
* Update the arm64 file paths in Documentation/efi-stub.txt to match
the current tree - Alan Ott
* Consistently preface all print statements with "efi" arch/x86 so
that it's more obvious to users reporting problems which statements
in the kernel log are relevant for EFI - Matt Fleming
* Fix a boot crash in the ACPI BGRT driver and delete
efi_lookup_mapped_addr() since it's useless now that the EFI
mappings *only* exist in the 'efi_pgd' page table. Instead we
always early_memremap() the BGRT memory - Sai Praneeth Prakhya
A couple of reference counting bugs here, one in spidev and one with
holding an extra reference in the core that we never freed if we removed
a device, plus a driver specific fix. Both of the refcounting bugs are
very old but they've only been found by observation so hopefully their
impact has been low.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWdUKcAAoJECTWi3JdVIfQO1EH/3aQKNFu1Z5cEaKiBtQ0aZZD
1E/w+OPqmKdaFDlXvwXO+W4UY5m0w0Kg5FPg4wMgpjDJQTiELtLJ3c4BiKp1Du8p
8RHnpqrYtggCZOK2r6iJNonIdIDDIDZMxxu1KHaKl+Wsqh9/1xUsQg7X9xi5Iaiv
fVd+QlhmCfC42lU92urBboPmON31XxaITTM8qNhGvQO77L4FdZHiVMP/bmyephV7
Mr4G7MFZHDZljGqEUhAlamhEiBxmCtQAm0eDhWmbYwN6S3U8L5VSqrkBDbNR08C+
4qnek2PS2/HlkQwMTpgGZpLrLyk04oWgsFMVZQ2275vR9qZlQTgnlEu50roBBD0=
=DMO9
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of reference counting bugs here, one in spidev and one with
holding an extra reference in the core that we never freed if we
removed a device, plus a driver specific fix. Both of the refcounting
bugs are very old but they've only been found by observation so
hopefully their impact has been low"
* tag 'spi-fix-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix parent-device reference leak
spi: spidev: Hold spi_lock over all defererences of spi in release()
spi-fsl-dspi: Fix CTAR Register access