gcc warns about a potential use of an uninitialized variable in this driver:
drivers/tty/serial/ifx6x60.c: In function 'ifx_spi_complete':
drivers/tty/serial/ifx6x60.c:713:6: warning: 'more' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (more || ifx_dev->spi_more || queue_length > 0 ||
Unlike a lot of other such warnings, this one is correct and describes
an actual problem in the handling of the "IFX_SPI_HEADER_F" result code.
This appears to be a result from a restructuring of the driver that
dates back to before it was merged in the kernel, so it's impossible
to know where it went wrong. I also don't know what that result code
means, so I have no idea if setting 'more' to zero is the correct
solution, but at least it makes the behavior reproducible rather than
depending on whatever happens to be on the kernel stack.
This patch initializes the 'more' variable to zero in each of the
three code paths that could result in undefined behavior before,
which is more explicit than initializing it at the start of the
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With SAMA5D2, the UART has hw timeout but the offset of the register to
define this value is not the same as the one for USART.
When using the new UART, the value of this register was 0 so we never
get timeout irqs. It involves that when using DMA, we were stuck until
the execution of the dma callback which happens when a buffer is full
(so after receiving 2048 bytes).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c39dfebc77, the modular support
code for atmel_serial was removed, as the driver cannot be built as a
module. Because no use case was proposed, the dynamic driver binding
support was removed as well.
The atmel_serial driver can manage up to 7 serial controllers, which are
multiplexed with other functions. For example, in the Atmel SAMA5D2, the
Flexcom controllers can work as USART, SPI or I2C controllers, and on
all Atmel devices serial lines can be reconfigured as GPIOs.
My use case uses GPIOs to transfer a firmware update using a custom
protocol on the lines used as a serial port during the normal life of
the device. If it is not possible to unbind the atmel_serial driver, the
GPIO lines remain reserved and prevent this case from working.
This patch reinstates the atmel_serial_remove function, and fixes it as
it failed to clear the "clk" field on removal, triggering an oops when
a device was bound again after being unbound.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kconfig option SERIAL_8250_RT288X seems to be only relevant on MIPS
platforms, so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Logic has been changed in kernel 3.4 by commit e9aba5158a
("tty: rework pty count limiting") but still not documented.
Sysctl kernel.pty.max works as global limit, kernel.pty.reserve ptys
are reserved for initial devpts instance (mounted without "newinstance").
Per-instance limit also could be set by mount option "max=%d".
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the platform bus sets the platform_device id to -1 (PLATFORM_DEVID_NONE),
use an incrementing counter for the TTY index instead
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable support for registering this device using the device tree.
Device tree node example for registering Goldfish TTY device :
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device generates a short rising pulse on the interrupt request line.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Better to hold the spinlock as short as possible.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is ideal to use when you need a lot of uarts in your FPGA.
Try not to force all those users to patch their kernel.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have channel offset defined since all BayTrail and Braswell
ports are 1 channel. Remove unneeded definition.
While here, remove comment which has no value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The managed API provides a better approach to help with acquiring and releasing
resources. Besides that error handling becomes simpler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are managed through clk-fractional-divider.c module, and thus CLK
framework takes care about it. Remove letfovers from this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the main branch contains return statement the 'else' keyword is not
needed. Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support early console setup via DT for all listed compatible strings.
Remove EARLYCON_DECLARE which was done by:
"Use common framework for earlycon declarations"
(sha1: 2eaa790989)
when OF_EARLYCON_DECLARE is defined.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit 2eaa790989 ("earlycon: Use common framework for
earlycon declarations") it is no longer needer to specify both
EARLYCON_DECLARE() and OF_EARLYCON_DECLARE().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When only a TX DMA channel is specified in DT, pl011_dma_probe() falls
back to looking for the optional RX channel in platform data. What it
doesn't do is check whether that platform data actually exists...
Add the missing check to avoid crashing the kernel.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_em485_init() is supposed to be protected with
p->port.lock spinlock.
This may lead to issues when kmalloc sleeps, so it is better to use
GFP_ATOMIC in this spinlocked context.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Reported-by: Ильяс Гасанов <torso.nafi@gmail.com>
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Formally, currently there is no memory leak, but if
serial8250_ports[line] is reused with other 8250 driver, then em485
will be already activated and it will cause issues.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While building with W=1 we were getting build warning:
drivers/tty/tty_audit.c:149:16: warning: variable 'sessionid' set but not used
The local variable sessionid was only assigned the value of
current->sessionid but was never reused. On further inspection it turned
out that there is no need of audit_get_loginuid() also.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a3f0b77f36.
Maarten writes:
It appears to be wrong and I don't have a good idea how to fix
it yet.
Cc: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Pull networking fixes from David Miller:
1) Fix ordering of WEXT netlink messages so we don't see a newlink
after a dellink, from Johannes Berg.
2) Out of bounds access in minstrel_ht_set_best_prob_rage, from
Konstantin Khlebnikov.
3) Paging buffer memory leak in iwlwifi, from Matti Gottlieb.
4) Wrong units used to set initial TCP rto from cached metrics, also
from Konstantin Khlebnikov.
5) Fix stale IP options data in the SKB control block from leaking
through layers of encapsulation, from Bernie Harris.
6) Zero padding len miscalculated in bnxt_en, from Michael Chan.
7) Only CHECKSUM_PARTIAL packets should be passed down through GSO, fix
from Hannes Frederic Sowa.
8) Fix suspend/resume with JME networking devices, from Diego Violat
and Guo-Fu Tseng.
9) Checksums not validated properly in bridge multicast support due to
the placement of the SKB header pointers at the time of the check,
fix from Álvaro Fernández Rojas.
10) Fix hang/tiemout with r8169 if a stats fetch is done while the
device is runtime suspended. From Chun-Hao Lin.
11) The forwarding database netlink dump facilities don't track the
state of the dump properly, resulting in skipped/missed entries.
From Minoura Makoto.
12) Fix regression from a recent 3c59x bug fix, from Neil Horman.
13) Fix list corruption in bna driver, from Ivan Vecera.
14) Big endian machines crash on vlan add in bnx2x, fix from Michal
Schmidt.
15) Ethtool RSS configuration not propagated properly in mlx5 driver,
from Tariq Toukan.
16) Fix regression in PHY probing in stmmac driver, from Gabriel
Fernandez.
17) Fix SKB tailroom calculation in igmp/mld code, from Benjamin
Poirier.
18) A past change to skip empty routing headers in ipv6 extention header
parsing accidently caused fragment headers to not be matched any
longer. Fix from Florian Westphal.
19) eTSEC-106 erratum needs to be applied to more gianfar chips, from
Atsushi Nemoto.
20) Fix netdev reference after free via workqueues in usb networking
drivers, from Oliver Neukum and Bjørn Mork.
21) mdio->irq is now an array rather than a pointer to dynamic memory,
but several drivers were still trying to free it :-/ Fixes from
Colin Ian King.
22) act_ipt iptables action forgets to set the family field, thus LOG
netfilter targets don't work with it. Fix from Phil Sutter.
23) SKB leak in ibmveth when skb_linearize() fails, from Thomas Falcon.
24) pskb_may_pull() cannot be called with interrupts disabled, fix code
that tries to do this in vmxnet3 driver, from Neil Horman.
25) be2net driver leaks iomap'd memory on removal, fix from Douglas
Miller.
26) Forgotton RTNL mutex unlock in ppp_create_interface() error paths,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (97 commits)
ppp: release rtnl mutex when interface creation fails
cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind
tcp: fix tcpi_segs_in after connection establishment
net: hns: fix the bug about loopback
jme: Fix device PM wakeup API usage
jme: Do not enable NIC WoL functions on S0
udp6: fix UDP/IPv6 encap resubmit path
be2net: Don't leak iomapped memory on removal.
vmxnet3: avoid calling pskb_may_pull with interrupts disabled
net: ethernet: Add missing MFD_SYSCON dependency on HAS_IOMEM
ibmveth: check return of skb_linearize in ibmveth_start_xmit
cdc_ncm: toggle altsetting to force reset before setup
usbnet: cleanup after bind() in probe()
mlxsw: pci: Correctly determine if descriptor queue is full
mlxsw: spectrum: Always decrement bridge's ref count
tipc: fix nullptr crash during subscription cancel
net: eth: altera: do not free array priv->mdio->irq
net/ethoc: do not free array priv->mdio->irq
net: sched: fix act_ipt for LOG target
asix: do not free array priv->mdio->irq
...
Pull overlayfs fixes from Miklos Szeredi:
"Overlayfs bug fixes. All marked as -stable material"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: copy new uid/gid into overlayfs runtime inode
ovl: ignore lower entries when checking purity of non-directory entries
ovl: fix getcwd() failure after unsuccessful rmdir
ovl: fix working on distributed fs as lower layer
The Synaptics 0x11e5 over I2C found in the Asus T100-CHI requires to
fetch the signature blob to actually start sending events.
With this patch, we should be close enough to the Windows driver which
checks the content of the blob at plugin to validate or not the
touchscreen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=113481
Fixes: 6d4f5440 ("HID: multitouch: Fetch feature reports on demand for Win8 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit b70af9bef4 ("mtd: nand: increase ready wait timeout and
report timeouts"), we increased the likelihood of scheduling during
nand_wait(). This makes us more likely to hit the time_before(...)
condition, since a lot of time may pass before we get scheduled again.
Now, the loop was already buggy, since we don't check if the NAND is
ready after exiting the loop; we simply print out a timeout warning. Fix
this by doing a final status check before printing a timeout message.
This isn't actually a critical bug, since the only effect is a false
warning print. But too many prints never hurt anyone, did they? :)
Side note: perhaps I'm not smart enough, but I'm not sure what the best
policy is for this kind of loop; do we busy loop (i.e., no
cond_resched()) to keep the lowest I/O latency (it's not great if the
resched is delaying Richard's system ~400ms)? Or do we allow
rescheduling, to play nice with the rest of the system (since some
operations can take quite a while)?
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Harvey Hunt <harvey.hunt@imgtec.com>
This reverts commit dbb17a21c1.
It turns out that commit can cause problems for systems with multiple
GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid
graphics.
This got noticed originally in 4.4.4, where this patch had already
gotten back-ported, but 4.5-rc7 was verified to have the same problem.
Alexander Deucher says:
"It looks like you have a muxed system so I suspect what's happening is
that one of the display is being reported as connected for both the
IGP and the dGPU and then the desktop environment gets confused or
there some sort problem in the detect functions since the mux is not
switched to the dGPU. I don't see an easy fix unless Dave has any
ideas. I'd say just revert for now"
Reported-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@kernel.org # wherever dbb17a21c1 got back-ported
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes this warning:
>> drivers/mtd/bcm63xxpart.c:175:4: note: in expansion of macro 'pr_err'
pr_err("invalid rootfs address: %*ph\n",
^
>> include/linux/kern_levels.h:4:18: warning: field width specifier '*' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add missing rtnl_unlock() in the error path of ppp_create_interface().
Fixes: 58a89ecaca ("ppp: fix lockdep splat in ppp_dev_uninit()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ubifs uses the write buffer size in recovery algorithm. When inspecting
an unclean ubifs recovery fails with writebuf size 64 in mtdram while
recovery on actual mtd device with writebuf size of 1024 succeeds.
So add a parameter for setting this property.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae87 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this removal, we don't need to 'get' the second DMA resource
either, as it's also unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If final packet (ACK) of 3WHS is lost, it appears we do not properly
account the following incoming segment into tcpi_segs_in
While we are at it, starts segs_in with one, to count the SYN packet.
We do not yet count number of SYN we received for a request sock, we
might add this someday.
packetdrill script showing proper behavior after fix :
// Tests tcpi_segs_in when 3rd packet (ACK) of 3WHS is lost
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
+.020 < P. 1:1001(1000) ack 1 win 32792
+0 accept(3, ..., ...) = 4
+.000 %{ assert tcpi_segs_in == 2, 'tcpi_segs_in=%d' % tcpi_segs_in }%
Fixes: 2efd055c53 ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will always be passed if the soc is tested the loopback cases. This
patch will fix this bug.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/power/devices.txt
The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.
Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.
And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it might be back on resume right after going to suspend in
some hardware.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hot add, vmbus_device_register() is called from vmbus_onoffer(), on
the same workqueue as the subchannel offer message work-queue, so
subchannel offer won't be processed until the vmbus_device_register()/...
/netvsc_probe() is done.
Also, vmbus_device_register() is called with channel_mutex locked, which
prevents subchannel processing too. So the "waiting for sub-channel
processing" will not success in hot add case. But, in usual module loading,
the netvsc_probe() is called from different code path, and doesn't fail.
This patch resolves the deadlock during NIC hot-add, and speeds up NIC
loading time.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_create_root_bus() passes a "parent" pointer to
pci_bus_assign_domain_nr(). When CONFIG_PCI_DOMAINS_GENERIC is defined,
pci_bus_assign_domain_nr() dereferences that pointer. Many callers of
pci_create_root_bus() supply a NULL "parent" pointer, which leads to a NULL
pointer dereference error.
7c67470009 ("PCI: Move domain assignment from arm64 to generic code")
moved the "parent" dereference from arm64 to generic code. Only arm64 used
that code (because only arm64 defined CONFIG_PCI_DOMAINS_GENERIC), and it
always supplied a valid "parent" pointer. Other arches supplied NULL
"parent" pointers but didn't defined CONFIG_PCI_DOMAINS_GENERIC, so they
used a no-op version of pci_bus_assign_domain_nr().
8c7d14746a ("ARM/PCI: Move to generic PCI domains") defined
CONFIG_PCI_DOMAINS_GENERIC on ARM, and many ARM platforms use
pci_common_init(), which supplies a NULL "parent" pointer.
These platforms (cns3xxx, dove, footbridge, iop13xx, etc.) crash
with a NULL pointer dereference like this while probing PCI:
Unable to handle kernel NULL pointer dereference at virtual address 000000a4
PC is at pci_bus_assign_domain_nr+0x10/0x84
LR is at pci_create_root_bus+0x48/0x2e4
Kernel panic - not syncing: Attempted to kill init!
[bhelgaas: changelog, add "Reported:" and "Fixes:" tags]
Reported: http://forum.doozan.com/read.php?2,17868,22070,quote=1
Fixes: 8c7d14746a ("ARM/PCI: Move to generic PCI domains")
Fixes: 7c67470009 ("PCI: Move domain assignment from arm64 to generic code")
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: stable@vger.kernel.org # v4.0+
Add optional properties for QSPI:
big-endian
if the register is big endian on this platform.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
new compatible string: "fsl,ls2080a-qspi".
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
IPv4 interprets a negative return value from a protocol handler as a
request to redispatch to a new protocol. In contrast, IPv6 interprets a
negative value as an error, and interprets a positive value as a request
for redispatch.
UDP for IPv6 was unaware of this difference. Change __udp6_lib_rcv() to
return a positive value for redispatch. Note that the socket's
encap_rcv hook still needs to return a negative value to request
dispatch, and in the case of IPv6 packets, adjust IP6CB(skb)->nhoff to
identify the byte containing the next protocol.
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter->pcicfg resource is either mapped via pci_iomap() or
derived from adapter->db. During be_remove() this resource was ignored
and so could remain mapped after remove.
Add a flag to track whether adapter->pcicfg was mapped or not, then
use that flag in be_unmap_pci_bars() to unmap if required.
Fixes: 25848c901 ("use PCI MMIO read instead of config read for errors")
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 has a function vmxnet3_parse_and_copy_hdr which, among other operations,
uses pskb_may_pull to linearize the header portion of an skb. That operation
eventually uses local_bh_disable/enable to ensure that it doesn't race with the
drivers bottom half handler. Unfortunately, vmxnet3 preforms this
parse_and_copy operation with a spinlock held and interrupts disabled. This
causes us to run afoul of the WARN_ON_ONCE(irqs_disabled()) warning in
local_bh_enable, resulting in this:
WARNING: at kernel/softirq.c:159 local_bh_enable+0x59/0x90() (Not tainted)
Hardware name: VMware Virtual Platform
Modules linked in: ipv6 ppdev parport_pc parport microcode e1000 vmware_balloon
vmxnet3 i2c_piix4 sg ext4 jbd2 mbcache sd_mod crc_t10dif sr_mod cdrom mptspi
mptscsih mptbase scsi_transport_spi pata_acpi ata_generic ata_piix vmwgfx ttm
drm_kms_helper drm i2c_core dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: mperf]
Pid: 6229, comm: sshd Not tainted 2.6.32-616.el6.i686 #1
Call Trace:
[<c04624d9>] ? warn_slowpath_common+0x89/0xe0
[<c0469e99>] ? local_bh_enable+0x59/0x90
[<c046254b>] ? warn_slowpath_null+0x1b/0x20
[<c0469e99>] ? local_bh_enable+0x59/0x90
[<c07bb936>] ? skb_copy_bits+0x126/0x210
[<f8d1d9fe>] ? ext4_ext_find_extent+0x24e/0x2d0 [ext4]
[<c07bc49e>] ? __pskb_pull_tail+0x6e/0x2b0
[<f95a6164>] ? vmxnet3_xmit_frame+0xba4/0xef0 [vmxnet3]
[<c05d15a6>] ? selinux_ip_postroute+0x56/0x320
[<c0615988>] ? cfq_add_rq_rb+0x98/0x110
[<c0852df8>] ? packet_rcv+0x48/0x350
[<c07c5839>] ? dev_queue_xmit_nit+0xc9/0x140
...
Fix it by splitting vmxnet3_parse_and_copy_hdr into two functions:
vmxnet3_parse_hdr, which sets up the internal/on stack ctx datastructure, and
pulls the skb (both of which can be done without holding the spinlock with irqs
disabled
and
vmxnet3_copy_header, which just copies the skb to the tx ring under the lock
safely.
tested and shown to correct the described problem. Applies cleanly to the head
of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
qed/qede: Add hardware GRO support
This patch series enables hardware GRO and add support for handling
HW aggregated TCP packets in driver receive flow by skipping
software GRO handling in stack.
Please consider applying this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures hardware to use GRO and adds support
for fastpath APIs to handle HW aggregated packets.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mainly structures and APIs prototype changes
in order to give support for qede slowpath/fastpath support
for the same.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* free firmware paging memory when the module is unloaded or device removed
* fix pending frames counter to fix an issue when removing stations
ssb
* fix a build problem related to ssb_fill_sprom_with_fallback()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJW2bUaAAoJEG4XJFUm622bfrAH/jy7VHux59vq30TGhNwBZKWi
Klgx4KPhv93kS9pj6eSN5QdSQ9JeYtSryo9d+isy/T77z3phrmmOPyjBbgWRm3eV
RGUccrhvpNRRoLhdNX2r6ubbwJ8MU3w/CIEK9RO16hxKu6XPqP1U9sfoxqQ7hswH
DKeTeu7nMfahe9923amo2wgSDkad14V8EaX009JHsh61QPyLF3QG8670PLwU2uFI
j4ThpMNBrgBsbtIr8qPfGDu1SvDClKhAIRjdCIylRRX3QScNfT81491N+uJafcyM
d4xiPyFFXzNtaYqYYVfN8DzJGseCI63wHN7KmzB405mAs9ciA2263GIen7ySXvg=
=LfgZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.5
iwlwifi
* free firmware paging memory when the module is unloaded or device removed
* fix pending frames counter to fix an issue when removing stations
ssb
* fix a build problem related to ssb_fill_sprom_with_fallback()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the c files less cluttered and enable netlink attributes to be
shared between files.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, arp_rcv() always return zero on a packet delivery upcall.
To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
v1->v2:
If sanity check is failed, call kfree_skb() instead of consume_skb(), then
return the correct return value.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
