[ Upstream commit 6daaae5ff7 ]
If the hotplug detect of a display is low for longer than one second
(configurable through drm_dp_cec_unregister_delay), then the CEC adapter
is unregistered since we assume the display was disconnected. If the
HPD went low for less than one second, then we check if the properties
of the CEC adapter have changed, since that indicates that we actually
switch to new hardware and we have to unregister the old CEC device and
register a new one.
Unfortunately, the test for changed properties was written poorly, and
after a new CEC capability was added to the CEC core code the test always
returned true (i.e. the properties had changed).
As a result the CEC device was unregistered and re-registered for every
HPD toggle. If the CEC remote controller integration was also enabled
(CONFIG_MEDIA_CEC_RC was set), then the corresponding input device was
also unregistered and re-registered. As a result the input device in
/sys would keep incrementing its number, e.g.:
/sys/devices/pci0000:00/0000:00:08.1/0000:e7:00.0/rc/rc0/input20
Since short HPD toggles are common, the number could over time get into
the thousands.
While not a serious issue (i.e. nothing crashes), it is not intended
to work that way.
This patch changes the test so that it only checks for the single CEC
capability that can actually change, and it ignores any other
capabilities, so this is now safe as well if new caps are added in
the future.
With the changed test the bit under #ifndef CONFIG_MEDIA_CEC_RC can be
dropped as well, so that's a nice cleanup.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Farblos <farblos@vodafonemail.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 2c6d1fffa1 ("drm: add support for DisplayPort CEC-Tunneling-over-AUX")
Tested-by: Farblos <farblos@vodafonemail.de>
Link: https://patchwork.freedesktop.org/patch/msgid/361bb03d-1691-4e23-84da-0861ead5dbdc@xs4all.nl
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f9eef9ec1 ]
HDCP must disabled encryption and restart authentication after
waiting KSV for 5s.
The original method uses a counter in a waitting loop that may
wait much longer than it is supposed to.
Use time_after() for KSV wait timeout.
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-9-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c01b0bae2 ]
When starting HDCP authentication, HDCP encryption should be enabled
when R0'is checked.
Change encryption enables time at R0' ready.
The hardware HDCP engine trigger is changed and the repeater KSV fails
will restart HDCP.
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-6-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fd2ff47d8 ]
When HDCP is activated,
a DisplayPort source receiving CP_IRQ from the sink
shall check Bstatus from DPCD and process the corresponding value
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-5-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e56ad45e99 ]
Source --> DP2.1 MST hub --> DP1.4/2.1 monitor
When change from DP1.4 to DP2.1 from monitor manual, modes higher than
4k120 are all cutoff by mode validation. Switch back to DP1.4 gets all
the modes up to 4k240 available to be enabled by dsc passthrough.
[why]
Compared to DP1.4 link from hub to monitor, DP2.1 link has larger
full_pbn value that causes overflow in the process of doing conversion
from pbn to kbps.
[how]
Change the data type accordingly to fit into the data limit during
conversion calculation.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81a9a93b16 ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-10-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e99c0b517b ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-9-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54c14f824 ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-8-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e8436d334 ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-5-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 819bee01ee ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-4-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39ead6e02e ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-3-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72bf423a6 ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-2-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df7c8e3dde ]
The connector->eld is accessed by the .get_eld() callback. This access
can collide with the drm_edid_to_eld() updating the data at the same
time. Add drm_connector.eld_mutex to protect the data from concurrenct
access. Individual drivers are not updated (to reduce possible issues
while applying the patch), maintainers are to find a best suitable way
to lock that mutex while accessing the ELD data.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-1-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c55b8ab6 ]
Having a fence linked to a virtio_gpu_framebuffer in the plane update
sequence would cause conflict when several planes referencing the same
framebuffer (e.g. Xorg screen covering multi-displays configured for an
extended mode) and those planes are updated concurrently. So it is needed
to allocate a fence for every plane state instead of the framebuffer.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
[dmitry.osipenko@collabora.com: rebase, fix up, edit commit message]
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241020230803.247419-2-dmitry.osipenko@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60a2c0c12b ]
Tear down ttm range manager for doorbell in function amdgpu_ttm_fini(),
to avoid memory leakage.
Fixes: 792b84fb90 ("drm/amdgpu: initialize ttm for doorbells")
Signed-off-by: Jiang Liu <gerry@linux.alibaba.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34a7401ff ]
Because the of_dma_configure() will returns '-EPROBE_DEFER' if the probe
procedure of the specific platform IOMMU driver is not finished yet. It
can also return other error code for various reasons.
Stop pretending that it will always suceess, quit if it fail.
Signed-off-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Fixes: 29ac8979cd ("drm/msm/a6xx: use msm_gem for GMU memory objects")
Fixes: 5a903a44a9 ("drm/msm/a6xx: Introduce GMU wrapper support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/622782/
Link: https://lore.kernel.org/r/20241104090738.529848-1-sui.jingfeng@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3676f37a88 ]
- The previous patch only considered the case for baremetal
and is not applicable for SRIOV code path. We also need to
init fw_share for SRIOV VF
Fixes: 928cd772e1 ("drm/amdgpu/vcn: reset fw_shared when VCPU buffers corrupted on vcn v4.0.3")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bokun Zhang <bokun.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b1ccb2a2 ]
Move rockchip_drm_drv.h in rockchip_drm_vop2.h to fix the follow
sparse warning:
ARCH=arm64 LLVM=1 make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
mrproper defconfig all -j12
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c:502:24: sparse:
warning: symbol 'vop2_platform_driver' was not declared. Should it
be static?
It is also beneficial for the upcoming support for rk3576.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Min-Hua Chen <minhuadotchen@gmail.com>
Tested-by: Detlev Casanova <detlev.casanova@collabora.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net> # on RK3568
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214081719.3330518-8-andyshrk@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c8546546f ]
The output interface related definition can shared between
vop and vop2, move them to rockchip_drm_drv.h can avoid duplicated
definition.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211115627.1784735-1-andyshrk@163.com
Stable-dep-of: 77b1ccb2a2 ("drm/rockchip: vop2: include rockchip_drm_drv.h")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ca953ac22 ]
Every layer of vop2 should bind a window, and we also need to make
sure that this window is not used by other layer.
0x5 is a reserved layer sel value on rk3568, but it will select
Cluster3 on rk3588, configure unused layers to 0x5 will lead
alpha blending error on rk3588.
When we bind a window from layerM to layerN, we move the old window
on layerN to layerM.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214081719.3330518-3-andyshrk@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 075a5b3969 ]
We need to setup background delay cycle and prescan
delay cycle when a mode is enable to avoid trigger
POST_BUF_EMPTY irq on rk3588.
Note: RK356x has no such requirement.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211115815.1785131-1-andyshrk@163.com
Stable-dep-of: 0ca953ac22 ("drm/rockchip: vop2: Fix the windows switch between different layers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd49ee4614 ]
Set overlay mode register according to the
output mode is yuv or rgb.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211115805.1785073-1-andyshrk@163.com
Stable-dep-of: 0ca953ac22 ("drm/rockchip: vop2: Fix the windows switch between different layers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b4dfdcde3 ]
The alpha setup should start from the second layer, the current calculation
starts incorrectly from the first layer, a negative offset will be obtained
in the following formula:
offset = (mixer_id + zpos - 1) * 0x10
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209122943.2781431-7-andyshrk@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17b4b10a0d ]
The phy_id of cluster windws are not increase one for each window.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209122943.2781431-6-andyshrk@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 357445e28f ]
The function atomctrl_get_smc_sclk_range_table() does not check the return
value of smu_atom_get_data_table(). If smu_atom_get_data_table() fails to
retrieve SMU_Info table, it returns NULL which is later dereferenced.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In practice this should never happen as this code only gets called
on polaris chips and the vbios data table will always be present on
those chips.
Fixes: a23eefa2f4 ("drm/amd/powerplay: enable dpm for baffin.")
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3300782d5 ]
In case of error after a amdgpu_gfx_rlc_enter_safe_mode() call, it is not
balanced by a corresponding amdgpu_gfx_rlc_exit_safe_mode() call.
Add the missing call.
Fixes: 9b7b8154cd ("drm/amd/powerplay: added didt support for vega10")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 834f304192 ]
In the etnaviv_gem_vmap_impl() function, the driver vmap whatever buffers
with write combine(WC) page property, this is incorrect. Cached buffers
should be mapped with the cached page property and uncached buffers should
be mapped with the uncached page property.
Fixes: a0a5ab3e99 ("drm/etnaviv: call correct function when trying to vmap a DMABUF")
Signed-off-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5c764d6ed ]
[Why]
Without the dmub hw lock, it may cause the lock timeout issue
while do modeset on PSR1 eDP panel.
[How]
Allow dmub hw lock for PSR1.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a2b5a99562)
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 2daba7d857 which is
commit 73dae652dc upstream.
The original patch 73dae652dc (drm/amdgpu: rework resume handling for
display (v2)), was only targeted at kernels 6.11 and newer. It did not
apply cleanly to 6.12 so I backported it and it backport landed as
99a02eab82 ("drm/amdgpu: rework resume handling for display (v2)"),
however there was a bug in the backport that was subsequently fixed in
063d380ca2 ("drm/amdgpu: fix backport of commit 73dae652dcac"). None
of this was intended for kernels older than 6.11, however the original
backport eventually landed in 6.6, 6.1, and 5.15.
Please revert the change from kernels 6.6, 6.1, and 5.15.
Link: https://lore.kernel.org/r/BL1PR12MB5144D5363FCE6F2FD3502534F7E72@BL1PR12MB5144.namprd12.prod.outlook.com
Link: https://lore.kernel.org/r/BL1PR12MB51449ADCFBF2314431F8BCFDF7132@BL1PR12MB5144.namprd12.prod.outlook.com
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Reported-by: Christian König <christian.koenig@amd.com>
Reported-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af04b320c7 upstream.
That is needed to enforce isolation between contexts.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit def59436fb)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a5401ec30 upstream.
Mesa changed its clear color alignment from 4k to 64 bytes
without informing the kernel side about the change. This
is now likely to cause framebuffer creation to fail.
The only thing we do with the clear color buffer in i915 is:
1. map a single page
2. read out bytes 16-23 from said page
3. unmap the page
So the only requirement we really have is that those 8 bytes
are all contained within one page. Thus we can deal with the
Mesa regression by reducing the alignment requiment from 4k
to the same 64 bytes in the kernel. We could even go as low as
32 bytes, but IIRC 64 bytes is the hardware requirement on
the 3D engine side so matching that seems sensible.
Note that the Mesa alignment chages were partially undone
so the regression itself was already fixed on userspace
side.
Cc: stable@vger.kernel.org
Cc: Sagar Ghuge <sagar.ghuge@intel.com>
Cc: Nanley Chery <nanley.g.chery@intel.com>
Reported-by: Xi Ruoyao <xry111@xry111.site>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13057
Closes: https://lore.kernel.org/all/45a5bba8de009347262d86a4acb27169d9ae0d9f.camel@xry111.site/
Link: 17f97a69c1
Link: 888f63cf1b
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241129065014.8363-2-ville.syrjala@linux.intel.com
Tested-by: Xi Ruoyao <xry111@xry111.site>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit ed3a892e5e)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f9910b41c upstream.
The fence sync logic doesn't handle a fence sync across devices
as it tries to write to a channel offset from one device into
the fence bo from a different device, which won't work so well.
This patch fixes that to avoid using the sync path in the case
where the fences come from different nouveau drm devices.
This works fine on a single device as the fence bo is shared
across the devices, and mapped into each channels vma space,
the channel offsets are therefore okay to pass between sides,
so one channel can sync on the seqnos from the other by using
the offset into it's vma.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
[ Fix compilation issue; remove version log from commit messsage.
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109005553.623947-1-airlied@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e4b5ccd392 ]
After a job completes, the corresponding pointer in the device must
be set to NULL. Failing to do so triggers a warning when unloading
the driver, as it appears the job is still active. To prevent this,
assign the job pointer to NULL after completing the job, indicating
the job has finished.
Fixes: 14d1d19086 ("drm/v3d: Remove the bad signaled() implementation.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113154741.67520-1-mcanal@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7d4062781 ]
Adds a new BO param that keeps the reservation locked after creation.
This removes the need to re-reserve the BO after creation which is a
waste of cycles.
This also fixes a bug in vmw_prime_import_sg_table where the imported
reservation is unlocked twice.
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Fixes: b32233acce ("drm/vmwgfx: Fix prime import/export")
Reviewed-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110185335.15301-1-ian.forbes@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8d9b91739 ]
Touching DISP_REG_OVL_PITCH_MSB leads to video overlay on MT2701, MT7623N
and probably other older SoCs being broken.
Move setting up AFBC layer configuration into a separate function only
being called on hardware which actually supports AFBC which restores the
behavior as it was before commit c410fa9b07 ("drm/mediatek: Add AFBC
support to Mediatek DRM driver") on non-AFBC hardware.
Fixes: c410fa9b07 ("drm/mediatek: Add AFBC support to Mediatek DRM driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/c7fbd3c3e633c0b7dd6d1cd78ccbdded31e1ca0f.1734397800.git.daniel@makrotopia.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 21541bc6b4 upstream.
As the hw supports up to 4 surfaces, increase the maximum number of
surfaces to prevent the DC error when trying to use more than three
planes.
[drm:dc_state_add_plane [amdgpu]] *ERROR* Surface: can not attach plane_state 000000003e2cb82c! Maximum is: 3
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3693
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b8d6daffc8)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0881fbc4fd upstream.
[Why]
Wrapper functions for dcn_bw_ceil2() and dcn_bw_floor2()
should check for granularity is non zero to avoid assert and
divide-by-zero error in dcn_bw_ functions.
[How]
Add check for granularity 0.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6e09701c3)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
