According to Synopsys DesignWare Cores Ethernet PCS databook, it is
required to disable Clause 37 auto-negotiation by programming bit-12
(AN_ENABLE) to 0 if it is already enabled, before programming various
fields of VR_MII_AN_CTRL registers.
After all these programming are done, it is then required to enable
Clause 37 auto-negotiation by programming bit-12 (AN_ENABLE) to 1.
Fixes: b97b5331b8 ("net: pcs: add C37 SGMII AN support for intel mGbE controller")
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The string should be "tx_disable" to match the state enum.
Fixes: 4005a7cb4f ("net: phy: sftp: print debug message with text, not numbers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b1c36aae51 ("regulator: Convert SY8106A binding to a schema")
converts sy8106a-regulator.txt to silergy,sy8106a.yaml, but missed to
adjust its reference in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about
a broken reference.
Repair this file reference in SY8106A REGULATOR DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211005075451.29691-11-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent change that started reporting break events forgot to push the
event to the line discipline, which meant that a detected break would
not be reported until further characters had been receive (the port
could even have been closed and reopened in between).
Fixes: 08dff274ed ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change that started reporting break events to the line
discipline caused the tty-buffer insertions to no longer be serialised
by inserting events also from the completion handler for the interrupt
endpoint.
Completion calls for distinct endpoints are not guaranteed to be
serialised. For example, in case a host-controller driver uses
bottom-half completion, the interrupt and bulk-in completion handlers
can end up running in parallel on two CPUs (high-and low-prio tasklets,
respectively) thereby breaking the tty layer's single producer
assumption.
Fix this by holding the read lock also when inserting characters from
the bulk endpoint.
Fixes: 08dff274ed ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Async feedback patches broke enumeration on Windows 10 previously fixed
by commit 789ea77310 ("usb: gadget: f_uac2: always increase endpoint
max_packet_size by one audio slot").
While the existing calculation for EP OUT capture for async mode yields
size+1 frame due to uac2_opts->fb_max > 0, playback side lost the +1
feature. Therefore the +1 frame addition must be re-introduced for
playback. Win10 enumerates the device only when both EP IN and EP OUT
max packet sizes are (at least) +1 frame.
Fixes: e89bb42883 ("usb: gadget: u_audio: add real feedback implementation")
Cc: stable <stable@vger.kernel.org>
Tested-by: Henrik Enquist <henrik.enquist@gmail.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20210924080027.5362-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_WWAN_CORE was with CONFIG_WWAN in commit 89212e160b ("net: wwan:
Fix WWAN config symbols"), but did not update all users of it. Change it
back to use CONFIG_WWAN instead.
Fixes: 89212e160b ("net: wwan: Fix WWAN config symbols")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210929194547.46954-2-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM for DRP should do the same action as SRC_ATTACHED when cc changes in
SRC_STARTUP state. Otherwise, TCPM will transition to SRC_UNATTACHED state
which is not satisfied with the Type-C spec.
Per Type-C spec:
DRP port should move to Unattached.SNK instead of Unattached.SRC if sink
removed.
Fixes: 4b4e02c831 ("typec: tcpm: Move out of staging")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210928111639.3854174-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB TCPCI Spec, 4.4.3 Mask Registers:
"A masked register will still indicate in the ALERT register, but shall
not set the Alert# pin low."
Thus, the Extended Status will still indicate in ALERT register if vSafe0V
is detected by TCPC even though being masked. In current code, howerer,
this event will not be handled in detection time. Rather it will be
handled when next ALERT event coming(CC evnet, PD event, etc).
Tcpm might transition to a wrong state in this situation. Thus, the vSafe0V
event should not be handled when it's masked.
Fixes: 766c485b86 ("usb: typec: tcpci: Add support to report vSafe0V")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210926101415.3775058-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no "connector" child node available on every
platform, so the driver can't fail to probe when it's
missing.
Fixes: 57560ee95c ("usb: typec: tipd: Don't block probing of consumer of "connector" nodes")
Cc: stable@vger.kernel.org # 5.14+
Reported-by: "Regupathy, Rajaram" <rajaram.regupathy@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210930124758.23233-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cb9c1cfc86 for
USB_LED_TRIG. This config symbol has bool type and enables extra code
in usb_common itself, not a separate driver. Enabling it should not
force usb_common to be built-in!
Fixes: cb9c1cfc86 ("usb: Kconfig: using select for USB_COMMON dependency")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Link: https://lore.kernel.org/r/20210921143442.340087-1-carnil@debian.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c6e23b89a9 ("usb: dwc3: gadget: set gadgets parent to the right
controller") changed the device for the UDC and broke the user space scripts
that instantiate the USB gadget(s) via ConfigFS.
Revert it for now until the better solution will be proposed.
Fixes: c6e23b89a9 ("usb: dwc3: gadget: set gadgets parent to the right controller")
Tested-by: Ferry Toth <fntoth@gmail.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211004141839.49079-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit de1799667b ("net: bridge: add STP xstats")
added an additional nla_reserve_64bit() in br_fill_linkxstats(),
but forgot to update br_get_linkxstats_size() accordingly.
This can trigger the following in rtnl_stats_get()
WARN_ON(err == -EMSGSIZE);
Fixes: de1799667b ("net: bridge: add STP xstats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The added #ifdefs in the PM rework were almost correct, but still
cause warnings in some randconfig builds:
drivers/usb/host/xhci-tegra.c:2147:12: error: 'tegra_xusb_resume' defined but not used [-Werror=unused-function]
2147 | static int tegra_xusb_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-tegra.c:2105:12: error: 'tegra_xusb_suspend' defined but not used [-Werror=unused-function]
2105 | static int tegra_xusb_suspend(struct device *dev)
Replace the #ifdef checks with simpler __maybe_unused annotations to
reliably shut up these warnings.
Link: https://lore.kernel.org/all/20210421135613.3560777-2-arnd@kernel.org/
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211005112057.2700888-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the situation that the disconnect event comes very late when the
device is unplugged, the driver would resubmit the RX bulk transfer
after getting the callback with -EPROTO immediately and continually.
Finally, soft lockup occurs.
This patch avoids to resubmit RX immediately. It uses a workqueue to
schedule the RX NAPI. And the NAPI would resubmit the RX. It let the
disconnect event have opportunity to stop the submission before soft
lockup.
Reported-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Tested-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew points out that eth_hw_addr_set() replaces memcpy()
calls so we can't use ether_addr_copy() which assumes
both arguments are 2-bytes aligned.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reboot the system by sysrq, the following bug will be occur.
BUG: sleeping function called from invalid context at kernel/locking/semaphore.c:90
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 10052, name: rc.shutdown
CPU: 3 PID: 10052 Comm: rc.shutdown Tainted: G W O 5.10.0 #1
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x18/0x28
dump_stack+0xd0/0x110
___might_sleep+0x14c/0x160
__might_sleep+0x74/0x88
down_interruptible+0x40/0x118
virt_efi_reset_system+0x3c/0xd0
efi_reboot+0xd4/0x11c
machine_restart+0x60/0x9c
emergency_restart+0x1c/0x2c
sysrq_handle_reboot+0x1c/0x2c
__handle_sysrq+0xd0/0x194
write_sysrq_trigger+0xbc/0xe4
proc_reg_write+0xd4/0xf0
vfs_write+0xa8/0x148
ksys_write+0x6c/0xd8
__arm64_sys_write+0x18/0x28
el0_svc_common.constprop.3+0xe4/0x16c
do_el0_svc+0x1c/0x2c
el0_svc+0x20/0x30
el0_sync_handler+0x80/0x17c
el0_sync+0x158/0x180
The reason for this problem is that irq has been disabled in
machine_restart() and then it calls down_interruptible() in
virt_efi_reset_system(), which would occur sleep in irq context,
it is dangerous! Commit 99409b935c9a("locking/semaphore: Add
might_sleep() to down_*() family") add might_sleep() in
down_interruptible(), so the bug info is here. down_trylock()
can solve this problem, cause there is no might_sleep.
--------
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhang Jianhua <chris.zjh@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Joe reports that using a statically allocated buffer for converting CPER
error records into human readable text is probably a bad idea. Even
though we are not aware of any actual issues, a stack buffer is clearly
a better choice here anyway, so let's move the buffer into the stack
frames of the two functions that refer to it.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The message
"Exiting boot services and installing virtual address map...\n"
is even shown if we have efi=novamap on the command line or the firmware
does not provide EFI_RT_SUPPORTED_SET_VIRTUAL_ADDRESS_MAP.
To avoid confusion just print
"Exiting boot services...\n"
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The problem is that "mac_id" is a u32 so this check for underflow does
not work when "mac_id" is zero. In that situation, "mac_id - 1" is
UINT_MAX instead of -1 so the condition is true. It leads to an
array underflow on the next line.
Fixes: 8cd574e6af ("staging: r8188eu: introduce new hal dir for RTL8188eu driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210930122604.GB10068@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison against SIZE_MAX produces a harmless warning on 64-bit
architectures:
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:185:16: error: result of comparison of constant 419244183493398898 with expression of type 'unsigned int' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (num_pages > (SIZE_MAX - sizeof(struct pagelist) -
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Shut up that warning by adding a cast to a longer type.
Fixes: ca641bae6d ("staging: vc04_services: prevent integer overflow in create_pagelist()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927113702.3866843-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cachefiles_cull() calls cachefiles_bury_object(), it passes
a NULL object. When this occurs, either trace_cachefiles_unlink()
or trace_cachefiles_rename() may oops due to the NULL object.
Check for NULL object in the tracepoint and if so, set debug_id
to MAX_UINT as was done in 2908f5e101.
The following oops was seen with xfstests generic/100.
BUG: kernel NULL pointer dereference, address: 0000000000000010
...
RIP: 0010:trace_event_raw_event_cachefiles_unlink+0x4e/0xa0 [cachefiles]
...
Call Trace:
cachefiles_bury_object+0x242/0x430 [cachefiles]
? __vfs_removexattr_locked+0x10f/0x150
? vfs_removexattr+0x51/0xd0
cachefiles_cull+0x84/0x120 [cachefiles]
cachefiles_daemon_cull+0xd1/0x120 [cachefiles]
cachefiles_daemon_write+0x158/0x190 [cachefiles]
vfs_write+0xbc/0x260
ksys_write+0x4f/0xc0
do_syscall_64+0x3b/0x90
The following oops was seen with xfstests generic/290.
BUG: kernel NULL pointer dereference, address: 0000000000000010
...
RIP: 0010:trace_event_raw_event_cachefiles_rename+0x54/0xa0 [cachefiles]
...
Call Trace:
cachefiles_bury_object+0x35c/0x430 [cachefiles]
cachefiles_cull+0x84/0x120 [cachefiles]
cachefiles_daemon_cull+0xd1/0x120 [cachefiles]
cachefiles_daemon_write+0x158/0x190 [cachefiles]
vfs_write+0xbc/0x260
ksys_write+0x4f/0xc0
do_syscall_64+0x3b/0x90
Fixes: 2908f5e101 ("fscache: Add a cookie debug ID and use that in traces")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://listman.redhat.com/archives/linux-cachefs/2021-October/msg00009.html
When arm_ffa firmware driver module is unloaded or removed we call
__ffa_devices_unregister on all the devices on the ffa bus. It must
unregister all the devices instead it is currently just releasing the
devices without unregistering. That is pure wrong as when we try to
load the module back again, it will result in the kernel crash something
like below.
-->8
CPU: 2 PID: 232 Comm: modprobe Not tainted 5.15.0-rc2+ #169
Hardware name: FVP Base RevC (DT)
Call trace:
dump_backtrace+0x0/0x1cc
show_stack+0x18/0x64
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
sysfs_create_dir_ns+0xe4/0x140
kobject_add_internal+0x170/0x358
kobject_add+0x94/0x100
device_add+0x178/0x5f0
device_register+0x20/0x30
ffa_device_register+0x80/0xcc [ffa_module]
ffa_setup_partitions+0x7c/0x108 [ffa_module]
init_module+0x290/0x2dc [ffa_module]
do_one_initcall+0xbc/0x230
do_init_module+0x58/0x304
load_module+0x15e0/0x1f68
__arm64_sys_finit_module+0xb8/0xf4
invoke_syscall+0x44/0x140
el0_svc_common+0xb4/0xf0
do_el0_svc+0x24/0x80
el0_svc+0x20/0x50
el0t_64_sync_handler+0x84/0xe4
el0t_64_sync+0x1a0/0x1a4
kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
register things with the same name in the same directory.
----
Fix the issue by calling device_unregister in __ffa_devices_unregister
which will also take care of calling device_release(which is mapped to
ffa_release_device)
Link: https://lore.kernel.org/r/20210924092859.3057562-2-sudeep.holla@arm.com
Fixes: e781858488 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the arm_ffa firmware driver can be built as module and hence
all the users of FFA driver. If any driver on the ffa bus is removed or
unregistered, the remove callback on all the device bound to the driver
being removed should be callback. For that to happen, we must register
a remove callback on the ffa_bus which is currently missing. This results
in the probe getting called again without the previous remove callback
on a device which may result in kernel crash.
Fix the issue by registering the remove callback on the FFA bus.
Link: https://lore.kernel.org/r/20210924092859.3057562-1-sudeep.holla@arm.com
Fixes: e781858488 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Usual mixed back of minor bug fixes.
adi,ad7192, ad7780, ad7793
* Fix incorrect IRQ_FLAG types. As the IRQ line is shared with the data
line we can be sure of the polarity and edge like nature. They were
previously either left unspecified or as level interrupts which may
cause problems on power up.
adi,adis16475
* Fix a deadlock by calling unlocked function when lock already held. Also
deal with making sure lock is released correctly.
adi,adis16480
* Fix assumption that all devices support sleep mode.
aspeed,adc
* Add missing platform_set_drvdata() so we can get the indio_dev in remove
as was being assumed.
fsl,fxls8962af
* Return IRQ_HANDLED on flush rather than a positive 'error' code.
maxim,max1207
* Fix a wrong shift on 12-bit devices that will lead to incorrect scale.
* Fix wrong number of channels on max1X31 devices due to allocating them twice.
mediatek,mt6577
* Fix a failure to apply scaling to IIO_CHAN_INFO_PROCESSED
renesas,rzg2l
* Fix failure to return -EBUSY on timeout due to ignored error code.
* Add a missing clk_disable_unprepare() on error in runtime_resume.
samsung,ssp_spi
* Fix an error code to always be returned on invalid length.
* Add some range checking to ensure resilience against bad data leading
to potential overflow.
ti,adc128s052
* Fix an error handling path that leaves regulator on if probe fails.
ti,dac5571
* Add missing return value in a switch default.
ti,opt3001
* Fix case where sensor returns 0 lux and we were previously accidentally
returning that this was a timeout.
-----BEGIN PGP SIGNATURE-----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=zA2d
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.15a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO fixes for the 5.15 cycle
Usual mixed back of minor bug fixes.
adi,ad7192, ad7780, ad7793
* Fix incorrect IRQ_FLAG types. As the IRQ line is shared with the data
line we can be sure of the polarity and edge like nature. They were
previously either left unspecified or as level interrupts which may
cause problems on power up.
adi,adis16475
* Fix a deadlock by calling unlocked function when lock already held. Also
deal with making sure lock is released correctly.
adi,adis16480
* Fix assumption that all devices support sleep mode.
aspeed,adc
* Add missing platform_set_drvdata() so we can get the indio_dev in remove
as was being assumed.
fsl,fxls8962af
* Return IRQ_HANDLED on flush rather than a positive 'error' code.
maxim,max1207
* Fix a wrong shift on 12-bit devices that will lead to incorrect scale.
* Fix wrong number of channels on max1X31 devices due to allocating them twice.
mediatek,mt6577
* Fix a failure to apply scaling to IIO_CHAN_INFO_PROCESSED
renesas,rzg2l
* Fix failure to return -EBUSY on timeout due to ignored error code.
* Add a missing clk_disable_unprepare() on error in runtime_resume.
samsung,ssp_spi
* Fix an error code to always be returned on invalid length.
* Add some range checking to ensure resilience against bad data leading
to potential overflow.
ti,adc128s052
* Fix an error handling path that leaves regulator on if probe fails.
ti,dac5571
* Add missing return value in a switch default.
ti,opt3001
* Fix case where sensor returns 0 lux and we were previously accidentally
returning that this was a timeout.
* tag 'iio-fixes-for-5.15a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: light: opt3001: Fixed timeout error when 0 lux
iio: adis16480: fix devices that do not support sleep mode
iio: mtk-auxadc: fix case IIO_CHAN_INFO_PROCESSED
iio: adis16475: fix deadlock on frequency set
iio: ssp_sensors: add more range checking in ssp_parse_dataframe()
iio: ssp_sensors: fix error code in ssp_print_mcu_debug()
iio: adc: ad7793: Fix IRQ flag
iio: adc: ad7780: Fix IRQ flag
iio: adc: ad7192: Add IRQ flag
iio: adc: aspeed: set driver data when adc probe.
iio: adc: rzg2l_adc: add missing clk_disable_unprepare() in rzg2l_adc_pm_runtime_resume()
iio: adc: max1027: Fix the number of max1X31 channels
iio: adc: max1027: Fix wrong shift with 12-bit devices
iio: adc128s052: Fix the error handling path of 'adc128_probe()'
iio: adc: rzg2l_adc: Fix -EBUSY timeout error return
iio: accel: fxls8962af: return IRQ_HANDLED when fifo is flushed
iio: dac: ti-dac5571: fix an error code in probe()
Looks like skl/bxt/derivatives also need the plane stride
stretch w/a when using async flips and VT-d is enabled, or
else we get corruption on screen. To my surprise this was
even documented in bspec, but only as a note on the
CHICHKEN_PIPESL register description rather than on the
w/a list.
So very much the same thing as on HSW/BDW, except the bits
moved yet again.
Cc: stable@vger.kernel.org
Cc: Karthik B S <karthik.b.s@intel.com>
Fixes: 55ea1cb178 ("drm/i915: Enable async flips in i915")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930190943.17547-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit d08df3b0bd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With patch "drm/i915/vbt: Fix backlight parsing for VBT 234+"
the size of bdb_lfp_backlight_data structure has been increased,
causing if-statement in the parse_lfp_backlight function
that comapres this structure size to the one retrieved from BDB,
always to fail for older revisions.
This patch calculates expected size of the structure for a given
BDB version and compares it with the value gathered from BDB.
Tested on Chromebook Pixelbook (Nocturne) (reports bdb->version = 221)
Fixes: d381baad29 ("drm/i915/vbt: Fix backlight parsing for VBT 234+")
Tested-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134606.227234-1-lma@semihalf.com
(cherry picked from commit 4378daf5d0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
(cherry picked from commit 7194dc998d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 989634fb49 ("drm/i915/audio: set HDA link parameters in
driver") makes HDMI audio on Lenovo P350 disappear.
So in addition to TGL, extend the logic to RKL to use BIOS provided
value to fix the regression.
Fixes: 989634fb49 ("drm/i915/audio: set HDA link parameters in driver")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906041300.508458-1-kai.heng.feng@canonical.com
(cherry picked from commit c6b40ee330)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In power save mode, the recording voice from headset mic will 2s more delay.
Add this patch will solve this issue.
[ minor coding style fix by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ccb0cdd5bbd7486eabbd8d987d384cb0@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both xen_pvh and xen_start_flags get written just once early during
init. Using the respective annotation then allows the open-coded placing
in .data to go away.
Additionally the former, like the latter, wants exporting, or else
xen_pvh_domain() can't be used from modules.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/8155ed26-5a1d-c06f-42d8-596d26e75849@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Two of the variables can live in .init.data, allowing the open-coded
placing in .data to go away. Another "variable" is used to communicate a
size value only to very early assembly code, which hence can be both
const and live in .init.*. Additionally two functions were lacking
__init annotations.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/3b0bb22e-43f4-e459-c5cb-169f996b5669@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
This was effectively lost while dropping PVHv1 code. Move the function
and arrange for it to be called the same way as done in PV mode. Clearly
this then needs re-introducing the XENFEAT_mmu_pt_update_preserve_ad
check that was recently removed, as that's a PV-only feature.
Since the string pointed at by pv_info.name describes the mode, drop
"paravirtualized" from the log message while moving the code.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/de03054d-a20d-2114-bb86-eec28e17b3b8@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Without announcing hvc0 as preferred it won't get used as long as tty0
gets registered earlier. This is particularly problematic with there not
being any screen output for PVH Dom0 when the screen is in graphics
mode, as the necessary information doesn't get conveyed yet from the
hypervisor.
Follow PV's model, but be conservative and do this for Dom0 only for
now.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/582328b6-c86c-37f3-d802-5539b7a86736@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
xenboot_write_console() is dealing with these quite fine so I don't see
why xenboot_console_setup() would return -ENOENT in this case.
Adjust documentation accordingly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/3d212583-700e-8b2d-727a-845ef33ac265@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
With preferred consoles "tty" and "hvc" announced as preferred,
registering "xenboot" early won't result in use of the console: It also
needs to be registered as preferred. Generalize this from being DomU-
only so far.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/d4a34540-a476-df2c-bca6-732d0d58c5f0@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
The xen_hvm_early_write() path better wouldn't be taken in this case;
while port 0xE9 can be used, the hypercall path is quite a bit more
efficient. Put that first, as it may also work for DomU-s (see also
xen_raw_console_write()).
While there also bail from the function when the first
domU_write_console() failed - later ones aren't going to succeed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/4fd89dcb-cfc5-c740-2e94-bb271e432d3e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Decouple XEN_DOM0 from XEN_PV, converting some existing uses of XEN_DOM0
to a new XEN_PV_DOM0. (I'm not convinced all are really / should really
be PV-specific, but for starters I've tried to be conservative.)
For PVH Dom0 the hypervisor populates MADT with only x2APIC entries, so
without x2APIC support enabled in the kernel things aren't going to work
very well. (As opposed, DomU-s would only ever see LAPIC entries in MADT
as of now.) Note that this then requires PVH Dom0 to be 64-bit, as
X86_X2APIC depends on X86_64.
In the course of this xen_running_on_version_or_later() needs to be
available more broadly. Move it from a PV-specific to a generic file,
considering that what it does isn't really PV-specific at all anyway.
Note that xen/interface/version.h cannot be included on its own; in
enlighten.c, which uses SCHEDOP_* anyway, include xen/interface/sched.h
first to resolve the apparently sole missing type (xen_ulong_t).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/983bb72f-53df-b6af-14bd-5e088bd06a08@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Like xen_start_flags, xen_domain_type gets set before .bss gets cleared.
Hence this variable also needs to be prevented from getting put in .bss,
which is possible because XEN_NATIVE is an enumerator evaluating to
zero. Any use prior to init_hvm_pv_info() setting the variable again
would lead to wrong decisions; one such case is xenboot_console_setup()
when called as a result of "earlyprintk=xen".
Use __ro_after_init as more applicable than either __section(".data") or
__read_mostly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/d301677b-6f22-5ae6-bd36-458e1f323d0b@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
The function doesn't use it and all of its callers say in a comment that
their respective arguments are to be non-NULL only in auto-translated
mode. Since xen_remap_domain_mfn_array() isn't supposed to be used by
non-PV, drop the parameter there as well. It was bogusly passed as non-
NULL (PRIV_VMA_LOCKED) by its only caller anyway. For
xen_remap_domain_gfn_range(), otoh, it's not clear at all why this
wouldn't want / might not need to gain auto-translated support down the
road, so the parameter is retained there despite now remaining unused
(and the only caller passing NULL); correct a respective comment as
well.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/036ad8a2-46f9-ac3d-6219-bdc93ab9e10b@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
xen_pfn_t is the same size as int only on 32-bit builds (and not even
on Arm32). Hence pfns[] can't be used directly to read individual error
values returned from xen_remap_domain_mfn_array(); every other error
indicator would be skipped/ignored on 64-bit.
Fixes: 3ad0876554 ("xen/privcmd: add IOCTL_PRIVCMD_MMAP_RESOURCE")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/aa6d6a67-6889-338a-a910-51e889f792d5@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Osstest has been suffering test failures for a little while from order-4
allocation failures, resulting from alloc_empty_pages() calling
kcalloc(). As there's no need for physically contiguous space here,
switch to kvcalloc().
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/6d698901-98a4-05be-c421-bcd0713f5335@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>