ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware version query is supported on the PFs. Due to this
following kernel warning log is observed:
[ 188.590344] mlx5_core 0000:08:00.2: mlx5_fw_version_query:816:(pid 1453): fw query isn't supported by the FW
Fix it by restricting the query and devlink info to the PF.
Fixes: 8338d93788 ("net/mlx5: Added devlink info callback")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Link: https://patch.msgid.link/20250306212529.429329-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-03-05 (ice)
This series contains updates to ice driver.
Larysa removes modification of destination override that caused LLDP
packets to be blocked.
Grzegorz fixes a memory leak in aRFS.
Marcin resolves an issue with operation of switchdev and LAG.
Przemek adjusts order of calls for registering devlink in relation to
health reporters.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: register devlink prior to creating health reporters
ice: Fix switchdev slow-path in LAG
ice: fix memory leak in aRFS after reset
ice: do not configure destination override for switchdev
====================
Link: https://patch.msgid.link/20250305213549.1514274-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
daddr can be NULL if there is no neighbour table entry present,
in that case the tx packet should be dropped.
saddr will usually be set by MCTP core, but check for NULL in case a
packet is transmitted by a different protocol.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: c8755b29b5 ("mctp i3c: MCTP I3C driver")
Link: https://patch.msgid.link/20250304-mctp-i3c-null-v1-1-4416bbd56540@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_health_init() was introduced in the commit 2a82874a3b ("ice: add
Tx hang devlink health reporter"). The call to it should have been put
after ice_devlink_register(). It went unnoticed until next reporter by
Konrad, which receives events from FW. FW is reporting all events, also
from prior driver load, and thus it is not unlikely to have something
at the very beginning. And that results in a splat:
[ 24.455950] ? devlink_recover_notify.constprop.0+0x198/0x1b0
[ 24.455973] devlink_health_report+0x5d/0x2a0
[ 24.455976] ? __pfx_ice_health_status_lookup_compare+0x10/0x10 [ice]
[ 24.456044] ice_process_health_status_event+0x1b7/0x200 [ice]
Do the analogous thing for deinit patch.
Fixes: 85d6164ec5 ("ice: add fw and port health reporters")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Konrad Knitter <konrad.knitter@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ever since removing switchdev control VSI and using PF for port
representor Tx/Rx, switchdev slow-path has been working improperly after
failover in SR-IOV LAG. LAG assumes that the first uplink to be added to
the aggregate will own VFs and have switchdev configured. After
failing-over to the other uplink, representors are still configured to
Tx through the uplink they are set up on, which fails because that
uplink is now down.
On failover, update all PRs on primary uplink to use the currently
active uplink for Tx. Call netif_keep_dst(), as the secondary uplink
might not be in switchdev mode. Also make sure to call
ice_eswitch_set_target_vsi() if uplink is in LAG.
On the Rx path, representors are already working properly, because
default Tx from VFs is set to PF owning the eswitch. After failover the
same PF is receiving traffic from VFs, even though link is down.
Fixes: defd52455a ("ice: do Tx through PF netdev in slow-path")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix aRFS (accelerated Receive Flow Steering) structures memory leak by
adding a checker to verify if aRFS memory is already allocated while
configuring VSI. aRFS objects are allocated in two cases:
- as part of VSI initialization (at probe), and
- as part of reset handling
However, VSI reconfiguration executed during reset involves memory
allocation one more time, without prior releasing already allocated
resources. This led to the memory leak with the following signature:
[root@os-delivery ~]# cat /sys/kernel/debug/kmemleak
unreferenced object 0xff3c1ca7252e6000 (size 8192):
comm "kworker/0:0", pid 8, jiffies 4296833052
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
[<ffffffff991ec485>] __kmalloc_cache_noprof+0x275/0x340
[<ffffffffc0a6e06a>] ice_init_arfs+0x3a/0xe0 [ice]
[<ffffffffc09f1027>] ice_vsi_cfg_def+0x607/0x850 [ice]
[<ffffffffc09f244b>] ice_vsi_setup+0x5b/0x130 [ice]
[<ffffffffc09c2131>] ice_init+0x1c1/0x460 [ice]
[<ffffffffc09c64af>] ice_probe+0x2af/0x520 [ice]
[<ffffffff994fbcd3>] local_pci_probe+0x43/0xa0
[<ffffffff98f07103>] work_for_cpu_fn+0x13/0x20
[<ffffffff98f0b6d9>] process_one_work+0x179/0x390
[<ffffffff98f0c1e9>] worker_thread+0x239/0x340
[<ffffffff98f14abc>] kthread+0xcc/0x100
[<ffffffff98e45a6d>] ret_from_fork+0x2d/0x50
[<ffffffff98e083ba>] ret_from_fork_asm+0x1a/0x30
...
Fixes: 28bf26724f ("ice: Implement aRFS")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After switchdev is enabled and disabled later, LLDP packets sending stops,
despite working perfectly fine before and during switchdev state.
To reproduce (creating/destroying VF is what triggers the reconfiguration):
devlink dev eswitch set pci/<address> mode switchdev
echo '2' > /sys/class/net/<ifname>/device/sriov_numvfs
echo '0' > /sys/class/net/<ifname>/device/sriov_numvfs
This happens because LLDP relies on the destination override functionality.
It needs to 1) set a flag in the descriptor, 2) set the VSI permission to
make it valid. The permissions are set when the PF VSI is first configured,
but switchdev then enables it for the uplink VSI (which is always the PF)
once more when configured and disables when deconfigured, which leads to
software-generated LLDP packets being blocked.
Do not modify the destination override permissions when configuring
switchdev, as the enabled state is the default configuration that is never
modified.
Fixes: 1a1c40df2e ("ice: set and release switchdev environment")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Syzbot caught an "KMSAN: uninit-value" warning [1], which is caused by the
ppp driver not initializing a 2-byte header when using socket filter.
The following code can generate a PPP filter BPF program:
'''
struct bpf_program fp;
pcap_t *handle;
handle = pcap_open_dead(DLT_PPP_PPPD, 65535);
pcap_compile(handle, &fp, "ip and outbound", 0, 0);
bpf_dump(&fp, 1);
'''
Its output is:
'''
(000) ldh [2]
(001) jeq #0x21 jt 2 jf 5
(002) ldb [0]
(003) jeq #0x1 jt 4 jf 5
(004) ret #65535
(005) ret #0
'''
Wen can find similar code at the following link:
https://github.com/ppp-project/ppp/blob/master/pppd/options.c#L1680
The maintainer of this code repository is also the original maintainer
of the ppp driver.
As you can see the BPF program skips 2 bytes of data and then reads the
'Protocol' field to determine if it's an IP packet. Then it read the first
byte of the first 2 bytes to determine the direction.
The issue is that only the first byte indicating direction is initialized
in current ppp driver code while the second byte is not initialized.
For normal BPF programs generated by libpcap, uninitialized data won't be
used, so it's not a problem. However, for carefully crafted BPF programs,
such as those generated by syzkaller [2], which start reading from offset
0, the uninitialized data will be used and caught by KMSAN.
[1] https://syzkaller.appspot.com/bug?extid=853242d9c9917165d791
[2] https://syzkaller.appspot.com/text?tag=ReproC&x=11994913980000
Cc: Paul Mackerras <paulus@samba.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+853242d9c9917165d791@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/bpf/000000000000dea025060d6bc3bc@google.com/
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250228141408.393864-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable the checksum option for these two endpoints in order to allow
mobile data to actually work. Without this, no packets seem to make it
through the IPA.
Fixes: b310de784b ("net: ipa: add IPA v4.7 support")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20250227-ipa-v4-7-fixes-v1-3-a88dd8249d8a@fairphone.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per downstream reference, max_writes should be 12 and max_reads
should be 13.
Fixes: b310de784b ("net: ipa: add IPA v4.7 support")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20250227-ipa-v4-7-fixes-v1-2-a88dd8249d8a@fairphone.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the downstream IPA driver there's only one group defined for source
and destination, and the destination group doesn't have a _DPL suffix.
Fixes: b310de784b ("net: ipa: add IPA v4.7 support")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20250227-ipa-v4-7-fixes-v1-1-a88dd8249d8a@fairphone.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* regressions from this cycle:
- mac80211: fix sparse warning for monitor
- nl80211: disable multi-link reconfiguration (needs fixing)
* older issues:
- cfg80211: reject badly combined cooked monitor,
fix regulatory hint validity checks
- mac80211: handle TXQ flush w/o driver per-sta flush,
fix debugfs for monitor, fix element inheritance
- iwlwifi: fix rfkill, dead firmware handling, rate API
version, free A-MSDU handling, avoid large
allocations, fix string format
- brcmfmac: fix power handling on some boards
-----BEGIN PGP SIGNATURE-----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=Dere
-----END PGP SIGNATURE-----
Merge tag 'wireless-2025-03-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
bugfixes for 6.14:
* regressions from this cycle:
- mac80211: fix sparse warning for monitor
- nl80211: disable multi-link reconfiguration (needs fixing)
* older issues:
- cfg80211: reject badly combined cooked monitor,
fix regulatory hint validity checks
- mac80211: handle TXQ flush w/o driver per-sta flush,
fix debugfs for monitor, fix element inheritance
- iwlwifi: fix rfkill, dead firmware handling, rate API
version, free A-MSDU handling, avoid large
allocations, fix string format
- brcmfmac: fix power handling on some boards
* tag 'wireless-2025-03-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: nl80211: disable multi-link reconfiguration
wifi: cfg80211: regulatory: improve invalid hints checking
wifi: brcmfmac: keep power during suspend if board requires it
wifi: mac80211: Fix sparse warning for monitor_sdata
wifi: mac80211: fix vendor-specific inheritance
wifi: mac80211: fix MLE non-inheritance parsing
wifi: iwlwifi: Fix A-MSDU TSO preparation
wifi: iwlwifi: Free pages allocated when failing to build A-MSDU
wifi: iwlwifi: limit printed string from FW file
wifi: iwlwifi: mvm: use the right version of the rate API
wifi: iwlwifi: mvm: don't try to talk to a dead firmware
wifi: iwlwifi: mvm: don't dump the firmware state upon RFKILL while suspend
wifi: iwlwifi: mvm: clean up ROC on failure
wifi: iwlwifi: fw: avoid using an uninitialized variable
wifi: iwlwifi: fw: allocate chained SG tables for dump
wifi: mac80211: remove debugfs dir for virtual monitor
wifi: mac80211: Cleanup sta TXQs on flush
wifi: nl80211: reject cooked mode if it is set along with other flags
====================
Link: https://patch.msgid.link/20250304124435.126272-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the initialization of ptp, hclge_ptp_get_cycle might return an error
and returned directly without unregister clock and free it. To avoid that,
call hclge_ptp_destroy_clock to unregist and free clock if
hclge_ptp_get_cycle failed.
Fixes: 8373cd38a8 ("net: hns3: change the method of obtaining default ptp cycle")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250228105258.1243461-1-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make NET_DSA_REALTEK_RTL8366RB_LEDS a hidden symbol.
It seems very unlikely user would want to intentionally
disable it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250228004534.3428681-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Partially revert commit b71724147e ("be2net: replace polling with
sleeping in the FW completion path") w.r.t mcc mutex it introduces and the
use of usleep_range. The be2net be_ndo_bridge_getlink() callback is
called with rcu_read_lock, so this code has been broken for a long time.
Both the mutex_lock and the usleep_range can cause the issue Ian Kumlien
reported[1]. The call path is:
be_ndo_bridge_getlink -> be_cmd_get_hsw_config -> be_mcc_notify_wait ->
be_mcc_wait_compl -> usleep_range()
[1] https://lore.kernel.org/netdev/CAA85sZveppNgEVa_FD+qhOMtG_AavK9_mFiU+jWrMtXmwqefGA@mail.gmail.com/
Tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Fixes: b71724147e ("be2net: replace polling with sleeping in the FW completion path")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250227164129.1201164-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
del_vqs() frees virtqueues, therefore cfv->vq_tx pointer should be checked
for NULL before calling it, not cfv->vdev. Also the current implementation
is redundant because the pointer cfv->vdev is dereferenced before it is
checked for NULL.
Fix this by checking cfv->vq_tx for NULL instead of cfv->vdev before
calling del_vqs().
Fixes: 0d2e1a2926 ("caif_virtio: Introduce caif over virtio")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250227184716.4715-1-v.shevtsov@mt-integration.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pcim_iomap_regions() should receive the driver's name as its third
parameter, not the PCI device's name.
Define the driver name with a macro and use it at the appropriate
places, including pcim_iomap_regions().
Cc: stable@vger.kernel.org # v5.14+
Fixes: 30bba69d7d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Tested-by: Henry Chen <chenx97@aosc.io>
Link: https://patch.msgid.link/20250226085208.97891-2-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IEP driver supports both perout and pps signal generation
but perout feature is faulty with half-cooked support
due to some missing configuration. Remove perout
support from the driver and reject perout requests with
"not supported" error code.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250227092441.1848419-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
irq_pool_alloc() debug print can print a null string.
Fix it by providing a default string to print.
Fixes: 71e084e264 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501141055.SwfIphN0-lkp@intel.com/
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250225072608.526866-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restore the `trace_mlx5_esw_vport_qos_create` event when creating
the vport scheduling element. This trace event was lost during
refactoring.
Fixes: be034baba8 ("net/mlx5: Make vport QoS enablement more flexible for future extensions")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250225072608.526866-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When enabling vport QoS fails, the scheduling node was never freed,
causing a leak.
Add the missing free and reset the vport scheduling node pointer to
NULL.
Fixes: be034baba8 ("net/mlx5: Make vport QoS enablement more flexible for future extensions")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250225072608.526866-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Non IP flow, with vlan tag not working as expected while
running below command for vlan-priority. fixed that.
ethtool -N eth1 flow-type ether vlan 0x8000 vlan-mask 0x1fff action 0 loc 0
Fixes: 1274daede3 ("net: mvpp2: cls: Add steering based on vlan Id and priority.")
Signed-off-by: Harshal Chaudhari <hchaudhari@marvell.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250225042058.2643838-1-hchaudhari@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a queue is stopped using the ndo queue API, before
destroying its page pool, the associated NAPI instance
needs to be unlinked to avoid warnings.
Handle this by calling page_pool_disable_direct_recycling()
when stopping a queue.
Cc: stable@vger.kernel.org
Fixes: ebdfae0d37 ("gve: adopt page pool for DQ RDA mode")
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250226003526.1546854-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 92cadedd9d ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on
suspend and then re-probed on resume.
This conflicts with some embedded boards that require to remain powered.
They will fail on resume with:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
This commit checks for the Device Tree property 'cap-power-off-cards'.
If this property is not set, it means that we do not have the capability
to power off and should therefore remain powered.
Signed-off-by: Matthias Proske <email@matthias-proske.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250212185941.146958-2-email@matthias-proske.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is an off-by-one issue for the err_chained_bd path, it will free
one more tx_swbd than expected. But there is no such issue for the
err_map_data path. To fix this off-by-one issue and make the two error
handling consistent, the increment of 'i' and 'count' remain in sync
and enetc_unwind_tx_frame() is called for error handling.
Fixes: fb8629e2cb ("net: enetc: add support for software TSO")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-9-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the ENETC v4 driver has not added the MAC merge layer support
in the upstream, so the mm_lock is not initialized and used, so remove
the mm_lock from the driver.
Fixes: 99100d0d99 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-8-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enetc4_link_init() is called when the PF driver probes to create
phylink and MDIO bus, but we forgot to call enetc4_link_deinit() to
free the phylink and MDIO bus when the driver was unbound. so add
missing enetc4_link_deinit() to enetc4_pf_netdev_destroy().
Fixes: 99100d0d99 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-7-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an issue with one-step timestamp based on UDP/IP. The peer will
discard the sync packet because of the wrong UDP checksum. For ENETC v1,
the software needs to update the UDP checksum when updating the
originTimestamp field, so that the hardware can correctly update the UDP
checksum when updating the correction field. Otherwise, the UDP checksum
in the sync packet will be wrong.
Fixes: 7294380c52 ("enetc: support PTP Sync packet one-step timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Actually ENETC VFs do not support HWTSTAMP_TX_ONESTEP_SYNC because only
ENETC PF can access PMa_SINGLE_STEP registers. And there will be a crash
if VFs are used to test one-step timestamp, the crash log as follows.
[ 129.110909] Unable to handle kernel paging request at virtual address 00000000000080c0
[ 129.287769] Call trace:
[ 129.290219] enetc_port_mac_wr+0x30/0xec (P)
[ 129.294504] enetc_start_xmit+0xda4/0xe74
[ 129.298525] enetc_xmit+0x70/0xec
[ 129.301848] dev_hard_start_xmit+0x98/0x118
Fixes: 41514737ec ("enetc: add get_ts_info interface for ethtool")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'xdp_tx' is used to count the number of XDP_TX frames sent, not the
number of Tx BDs.
Fixes: 7ed2bc8007 ("net: enetc: add support for XDP_TX")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-4-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When creating a TSO header, if the skb is VLAN tagged, the extended BD
will be used and the 'count' should be increased by 2 instead of 1.
Otherwise, when an error occurs, less tx_swbd will be freed than the
actual number.
Fixes: fb8629e2cb ("net: enetc: add support for software TSO")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a DMA mapping error occurs while processing skb frags, it will free
one more tx_swbd than expected, so fix this off-by-one issue.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 23c0e5a16b ("ixgbe: Add link management support for E610
device") introduced incorrect checking of media cage presence for E610
device. Fix it.
Fixes: 23c0e5a16b ("ixgbe: Add link management support for E610 device")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/e7d73b32-f12a-49d1-8b60-1ef83359ec13@stanley.mountain/
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have recently seen reports of lockdep circular lock dependency warnings
when loading the iAVF driver:
[ 1504.790308] ======================================================
[ 1504.790309] WARNING: possible circular locking dependency detected
[ 1504.790310] 6.13.0 #net_next_rt.c2933b2befe2.el9 Not tainted
[ 1504.790311] ------------------------------------------------------
[ 1504.790312] kworker/u128:0/13566 is trying to acquire lock:
[ 1504.790313] ffff97d0e4738f18 (&dev->lock){+.+.}-{4:4}, at: register_netdevice+0x52c/0x710
[ 1504.790320]
[ 1504.790320] but task is already holding lock:
[ 1504.790321] ffff97d0e47392e8 (&adapter->crit_lock){+.+.}-{4:4}, at: iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790330]
[ 1504.790330] which lock already depends on the new lock.
[ 1504.790330]
[ 1504.790330]
[ 1504.790330] the existing dependency chain (in reverse order) is:
[ 1504.790331]
[ 1504.790331] -> #1 (&adapter->crit_lock){+.+.}-{4:4}:
[ 1504.790333] __lock_acquire+0x52d/0xbb0
[ 1504.790337] lock_acquire+0xd9/0x330
[ 1504.790338] mutex_lock_nested+0x4b/0xb0
[ 1504.790341] iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790347] process_one_work+0x248/0x6d0
[ 1504.790350] worker_thread+0x18d/0x330
[ 1504.790352] kthread+0x10e/0x250
[ 1504.790354] ret_from_fork+0x30/0x50
[ 1504.790357] ret_from_fork_asm+0x1a/0x30
[ 1504.790361]
[ 1504.790361] -> #0 (&dev->lock){+.+.}-{4:4}:
[ 1504.790364] check_prev_add+0xf1/0xce0
[ 1504.790366] validate_chain+0x46a/0x570
[ 1504.790368] __lock_acquire+0x52d/0xbb0
[ 1504.790370] lock_acquire+0xd9/0x330
[ 1504.790371] mutex_lock_nested+0x4b/0xb0
[ 1504.790372] register_netdevice+0x52c/0x710
[ 1504.790374] iavf_finish_config+0xfa/0x240 [iavf]
[ 1504.790379] process_one_work+0x248/0x6d0
[ 1504.790381] worker_thread+0x18d/0x330
[ 1504.790383] kthread+0x10e/0x250
[ 1504.790385] ret_from_fork+0x30/0x50
[ 1504.790387] ret_from_fork_asm+0x1a/0x30
[ 1504.790389]
[ 1504.790389] other info that might help us debug this:
[ 1504.790389]
[ 1504.790389] Possible unsafe locking scenario:
[ 1504.790389]
[ 1504.790390] CPU0 CPU1
[ 1504.790391] ---- ----
[ 1504.790391] lock(&adapter->crit_lock);
[ 1504.790393] lock(&dev->lock);
[ 1504.790394] lock(&adapter->crit_lock);
[ 1504.790395] lock(&dev->lock);
[ 1504.790397]
[ 1504.790397] *** DEADLOCK ***
This appears to be caused by the change in commit 5fda3f3534 ("net: make
netdev_lock() protect netdev->reg_state"), which added a netdev_lock() in
register_netdevice.
The iAVF driver calls register_netdevice() from iavf_finish_config(), as a
final stage of its state machine post-probe. It currently takes the RTNL
lock, then the netdev lock, and then the device critical lock. This pattern
is used throughout the driver. Thus there is a strong dependency that the
crit_lock should not be acquired before the net device lock. The change to
register_netdevice creates an ABBA lock order violation because the iAVF
driver is holding the crit_lock while calling register_netdevice, which
then takes the netdev_lock.
It seems likely that future refactors could result in netdev APIs which
hold the netdev_lock while calling into the driver. This means that we
should not re-order the locks so that netdev_lock is acquired after the
device private crit_lock.
Instead, notice that we already release the netdev_lock prior to calling
the register_netdevice. This flow only happens during the early driver
initialization as we transition through the __IAVF_STARTUP,
__IAVF_INIT_VERSION_CHECK, __IAVF_INIT_GET_RESOURCES, etc.
Analyzing the places where we take crit_lock in the driver there are two
sources:
a) several of the work queue tasks including adminq_task, watchdog_task,
reset_task, and the finish_config task.
b) various callbacks which ultimately stem back to .ndo operations or
ethtool operations.
The latter cannot be triggered until after the netdevice registration is
completed successfully.
The iAVF driver uses alloc_ordered_workqueue, which is an unbound workqueue
that has a max limit of 1, and thus guarantees that only a single work item
on the queue is executing at any given time, so none of the other work
threads could be executing due to the ordered workqueue guarantees.
The iavf_finish_config() function also does not do anything else after
register_netdevice, unless it fails. It seems unlikely that the driver
private crit_lock is protecting anything that register_netdevice() itself
touches.
Thus, to fix this ABBA lock violation, lets simply release the
adapter->crit_lock as well as netdev_lock prior to calling
register_netdevice(). We do still keep holding the RTNL lock as required by
the function. If we do fail to register the netdevice, then we re-acquire
the adapter critical lock to finish the transition back to
__IAVF_INIT_CONFIG_ADAPTER.
This ensures every call where both netdev_lock and the adapter->crit_lock
are acquired under the same ordering.
Fixes: afc664987a ("eth: iavf: extend the netdev_lock usage")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of switchdev environment setup, uplink VSI is configured as
default for both Tx and Rx. Default Rx VSI is also used by promiscuous
mode. If promisc mode is enabled and an attempt to enter switchdev mode
is made, the setup will fail because Rx VSI is already configured as
default (rule exists).
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
In switchdev setup, use ice_set_dflt_vsi() instead of plain
ice_cfg_dflt_vsi(), which avoids repeating setting default VSI for Rx if
it's already configured.
Fixes: 50d62022f4 ("ice: default Tx rule instead of to queue")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ice_ena_vfs() fails after calling ice_create_vf_entries(), it frees
all VFs without removing them from snapshot PF-VF mailbox list, leading
to list corruption.
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
Trace (minimized):
list_add corruption. next->prev should be prev (ffff8882e241c6f0), but was 0000000000000000. (next=ffff888455da1330).
kernel BUG at lib/list_debug.c:29!
RIP: 0010:__list_add_valid_or_report+0xa6/0x100
ice_mbx_init_vf_info+0xa7/0x180 [ice]
ice_initialize_vf_entry+0x1fa/0x250 [ice]
ice_sriov_configure+0x8d7/0x1520 [ice]
? __percpu_ref_switch_mode+0x1b1/0x5d0
? __pfx_ice_sriov_configure+0x10/0x10 [ice]
Sometimes a KASAN report can be seen instead with a similar stack trace:
BUG: KASAN: use-after-free in __list_add_valid_or_report+0xf1/0x100
VFs are added to this list in ice_mbx_init_vf_info(), but only removed
in ice_free_vfs(). Move the removing to ice_free_vf_entries(), which is
also being called in other places where VFs are being removed (including
ice_free_vfs() itself).
Fixes: 8cd8a6b17d ("ice: move VF overflow message count into struct ice_mbx_vf_info")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test XDP and HDS interaction. While at it add a test for using the IOCTL,
as that turned out to be the real culprit.
Testing bnxt:
# NETIF=eth0 ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable # SKIP disabling of HDS not supported by the device
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:11 fail:0 xfail:0 xpass:0 skip:1 error:0
and netdevsim:
# ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Netdevsim needs a sane default for tx/rx ring size.
ethtool 6.11 is needed for the --disable-netlink option.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250221025141.1132944-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats calculations involve a RMW to add the stat update to the existing
value. This is currently not protected by any synchronization mechanism,
so data races are possible. Add a spinlock to protect the update. The
reader side could be protected using u64_stats, but we would still need
a spinlock for the update side anyway. And we always do an update
immediately before reading the stats anyway.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250220162950.95941-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
IPv4 neighbors can be constructed on the blackhole net device, but they
are constructed with an output function (neigh_direct_output()) that
simply calls dev_queue_xmit(). The latter will transmit packets via
'skb->dev' which might not be the blackhole net device if dst_dev_put()
switched 'dst->dev' to the blackhole net device while another CPU was
using the dst entry in ip_output(), but after it already initialized
'skb->dev' from 'dst->dev'.
Specifically, the following can happen:
CPU1 CPU2
udp_sendmsg(sk1) udp_sendmsg(sk2)
udp_send_skb() [...]
ip_output()
skb->dev = skb_dst(skb)->dev
dst_dev_put()
dst->dev = blackhole_netdev
ip_finish_output2()
resolves neigh on dst->dev
neigh_output()
neigh_direct_output()
dev_queue_xmit()
This will result in IPv4 packets being sent without an Ethernet header
via a valid net device:
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on enp9s0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
22:07:02.329668 20:00:40:11:18:fb > 45:00:00:44:f4:94, ethertype Unknown
(0x58c6), length 68:
0x0000: 8dda 74ca f1ae ca6c ca6c 0098 969c 0400 ..t....l.l......
0x0010: 0000 4730 3f18 6800 0000 0000 0000 9971 ..G0?.h........q
0x0020: c4c9 9055 a157 0a70 9ead bf83 38ca ab38 ...U.W.p....8..8
0x0030: 8add ab96 e052 .....R
Fix by making sure that neighbors are constructed on top of the
blackhole net device with an output function that simply consumes the
packets, in a similar fashion to dst_discard_out() and
blackhole_netdev_xmit().
Fixes: 8d7017fd62 ("blackhole_netdev: use blackhole_netdev to invalidate dst entries")
Fixes: 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
Reported-by: Florian Meister <fmei@sfs.com>
Closes: https://lore.kernel.org/netdev/20250210084931.23a5c2e4@hermes.local/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250220072559.782296-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Loongson's DWMAC device may take nearly two seconds to complete DMA reset,
however, the default waiting time for reset is 200 milliseconds.
Therefore, the following error message may appear:
[14.427169] dwmac-loongson-pci 0000:00:03.2: Failed to reset the dma
Fixes: 803fc61df2 ("net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support")
Cc: stable@vger.kernel.org
Signed-off-by: Qunqin Zhao <zhaoqunqin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Yanteng Si <si.yanteng@linux.dev>
Link: https://patch.msgid.link/20250219020701.15139-1-zhaoqunqin@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While setting the DAC value, the wrong boolean value is evaluated to set
the DSP bias current. So let's correct the conditional statement and use
the right boolean value read from the DTS set in the priv.
Cc: stable@vger.kernel.org
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250219130923.7216-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The external PHY will undergo a soft reset twice during the resume process
when it wake up from suspend. The first reset occurs when the axienet
driver calls phylink_of_phy_connect(), and the second occurs when
mdio_bus_phy_resume() invokes phy_init_hw(). The second soft reset of the
external PHY does not reinitialize the internal PHY, which causes issues
with the internal PHY, resulting in the PHY link being down. To prevent
this, setting the mac_managed_pm flag skips the mdio_bus_phy_resume()
function.
Fixes: a129b41fe0 ("Revert "net: phy: dp83867: perform soft reset and retain established link"")
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250217055843.19799-1-nick.hu@sifive.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>