In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Link: https://lkml.kernel.org/r/1406038688-26417-1-git-send-email-weiyj_lk@163.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In Armada 375 SoCs, the MDIO is handled by a separate orion-mdio driver,
despite the register is contained within the "LMS" block of the network
controller.
Therefore we need to add the clock to the MDIO devicetree to prevent the
controller from being accesed with its clock gated. This is needed, for
instance, to be able to load the MDIO driver before the network driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1405961296-5846-7-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
TWL4030's Battery Charger seems to be designed for non-hotpluggable
batteries.
If battery is not present in the system, BATSTS is always set with the
expectation that software will take actions to move to a required safe
state (could be power down or disable various charger paths).
It does not seem possible even by manipulating the edge detection
of the event (using BCIEDR2 register) to have a consistent hotplug
handling. This seems to be the result of BATSTS interrupt generated
when the thermistor of the battery pack is disconnected from the
dedicated ADIN1 pin. Clearing the status just results in the status
being regenerated by the monitoring ADC(MADC) and disabling the
edges of event just makes hotplug no longer function. The only
other option is to disable the detection of the MADC by disabling
BCIMFEN4::BATSTSMCHGEN (battery presence detector) - but then, we can
never again detect battery reconnection.
So, detect battery presence based on precharge(which is hardware
automatic state) or default main charger configuration at the time of
probe and enable charger logic only if battery was present.
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for reboot functionality on boards with ARM-based
Broadcom STB chipsets. Make it built-in by default for ARCH_BRCMSTB,
but allow it to be configurable under COMPILE_TEST.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Pull clockevents from Danel Lezcano:
* New timer driver for the Cirrus Logic CLPS711X SoC
* New driver for the Mediatek SoC which includes:
* A new function for of, acked by Rob Herring
* Move the PXA driver to drivers/clocksource, add DT support
* Optimization of the exynos_mct driver
* DT support for the renesas timers family.
* Some Kconfig and driver fixlets
ZONE_DMA is created to allow 32-bit only devices to access memory in the
absence of an IOMMU. On systems where the memory starts above 4GB, it is
expected that some devices have a DMA offset hardwired to be able to
access the bottom of the memory. Linux currently supports DT bindings
for the DMA offsets but they are not (easily) available early during
boot.
This patch tries to guess a DMA offset and assumes that ZONE_DMA
corresponds to the 32-bit mask above the start of DRAM.
Fixes: 2d5a5612bc (arm64: Limit the CMA buffer to 32-bit if ZONE_DMA)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
The MCT has a nice 64-bit counter. That means that we _can_ register
as a 64-bit clocksource and sched_clock. ...but that doesn't mean we
should.
The 64-bit counter is read by reading two 32-bit registers. That
means reading needs to be something like:
- Read upper half
- Read lower half
- Read upper half and confirm that it hasn't changed.
That wouldn't be terrible, but:
- THe MCT isn't very fast to access (hundreds of nanoseconds).
- The clocksource is queried _all the time_.
In total system profiles of real workloads on ChromeOS, we've seen
exynos_frc_read() taking 2% or more of CPU time even after optimizing
the 3 reads above to 2 (see below).
The MCT is clocked at ~24MHz on all known systems. That means that
the 32-bit half of the counter rolls over every ~178 seconds. This
inspired an optimization in ChromeOS to cache the upper half between
calls, moving 3 reads to 2. ...but we can do better! Having a 32-bit
timer that flips every 178 seconds is more than sufficient for Linux.
Let's just use the lower half of the MCT.
Times on 5420 to do 1000000 gettimeofday() calls from userspace:
* Original code: 1323852 us
* ChromeOS cache upper half: 1173084 us
* ChromeOS + ldmia to optimize: 1045674 us
* Use lower 32-bit only (this code): 1014429 us
As you can see, the time used doesn't increase linearly with the
number of reads and we can make 64-bit work almost as fast as 32-bit
with a bit of assembly code. But since there's no real gain for
64-bit, let's go with the simplest and fastest implementation.
Note: with this change roughly half the time for gettimeofday() is
spent in exynos_frc_read(). The rest is timer / system call overhead.
Also note: this patch disables the use of the MCT on ARM64 systems
until we've sorted out how to make "cycles_t" always 32-bit. Really
ARM64 systems should be using arch timers anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Using the __raw functions is discouraged. Update the file to
consistently use the proper functions.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
As clocksource pxa_timer was moved to clocksource framework, the
pxa_timer initialization needs to be a bit amended, to pass the
necessary informations to clocksource, ie :
- the timer interrupt (mach specific)
- the timer registers base (ditto)
- the timer clockrate
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Select CLKSRC_OF for PXA architectures.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add device-tree support to PXA platforms.
The driver still needs to maintain backward non device-tree
compatibility as well, which implies :
- a non device-tree init function
- a static registers base address in the driver
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Move time.c from arch/arm/mach-pxa/time.c to
drivers/clocksource/pxa_timer.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds the clocksource driver for Cirrus Logic CLPS711X series SoCs.
Designed primarily for migration CLPS711X subarch for multiplatform & DT,
for this as the "OF" and "non-OF" calls implemented.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In the clocksource driver, we didn't explicitly enable the clock. it makes the
clk reference counter wrong. We didn't encounter any hang issue because the
tick's clock input has been open and is shared by some other hardware
components, but if we don't enable those components in kernel, in the stage of
disabling unused clk in kernel boot, Linux tick hangs.
This patch fixes it. it does an explicit prepare and enable to the clock input,
and increases the usage counter of the clk.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In 'em_sti.c', it will call devm_ioremap_resource() which need
HAS_IOMEM. So need let EM_TIMER_STI depend on HAS_IOMEM, too.
The related error (with allmodconfig under score):
LD init/built-in.o
em_sti.c:(.text.em_sti_probe+0x84): undefined reference to `devm_ioremap_resource'
make: *** [vmlinux] Error 1
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add binding documentation for the General Purpose Timer driver of
the Mediatek SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch adds a clock source and clock event for the timer found
on the Mediatek SoCs.
The Mediatek General Purpose Timer block provides five 32 bit timers and
one 64 bit timer.
Two 32 bit timers are used by this driver:
TIMER1: clock events supporting periodic and oneshot events
TIMER2: clock source configured as a free running counter
The General Purpose Timer block can be run with two clocks. A 13 MHz system
clock and the RTC clock running at 32 KHz. This implementation uses the system
clock with no clock source divider.
The interrupts are shared between the different timers and have to be read back
from a register. We just enable one interrupt for the clock event. The clock
event timer is used by all cores.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
A call to of_iomap does not request the memory region. This patch adds the
function of_io_request_and_map which requests the memory region before
mapping it.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It should be "MTU2" instead of "TMU2"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Adds ability to shutdown all CPUs except the first one
(since it might be special for a lot of platforms).
It is now possible to use kexec which requires such a feature.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When compiling for multiplatform for both ARMv6 and ARMv7, the default
compiler flags are for ARMv6, and the following cpu-hotplug change will
fail with:
/tmp/ccSFxfmI.s:68: Error: selected processor does not support ARM mode `isb '
/tmp/ccSFxfmI.s:74: Error: selected processor does not support ARM mode `isb '
/tmp/ccSFxfmI.s:75: Error: selected processor does not support ARM mode `dsb '
Fix this in a similar manner as in commit 9f0affcf3e "ARM: mvebu: Fix pmsu
compilation when ARMv6 is selected", by specifying ARMv7 flags for platsmp.o.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds bch8 ecc software fallback which is mostly used by
omap3s because they lack hardware elm support.
Fixes: 0611c41934 (ARM: OMAP2+: gpmc:
update gpmc_hwecc_bch_capable() for new platforms and ECC schemes)
Cc: <stable@vger.kernel.org> # 3.15.x+
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we start to decomission the return value from gpiochip_remove()
the compilers emit warnings due to the function being tagged
__must_check. So drop this until we remove the return value
altogether.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DRA74/72 control module pins have a weak pull up and pull down.
This is configured by bit offset 17. if BIT(17) is 1, a pull up is
selected, else a pull down is selected.
However, this pull resisstor is applied based on BIT(16) -
PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is
applied, else no weak pulls are applied. We defined this in reverse.
Reference: Table 18-5 (Description of the pad configuration register
bits) in Technical Reference Manual Revision (DRA74x revision Q:
SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised
June 2014)
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A reference to ARCH_HAS_OPP was added in commit 333d17e56 (arm64: add
ARCH_HAS_OPP to allow enabling OPP library) however this symbol is no
longer needed after commit 049d595a4d (PM / OPP: Make OPP invisible
to users in Kconfig).
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
although one patch adds DSS hwmods for AM43xx.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-v3.17/20140722143514/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=csSf
-----END PGP SIGNATURE-----
Merge tag 'for-v3.17/omap-hwmod-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
OMAP hwmod data additions for v3.17. Most of these are DRA7xx-related,
although one patch adds DSS hwmods for AM43xx.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-v3.17/20140722143514/
In the recent commit b50a6c584b "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584b ("powerpc/perf: Clear MMCR2 when enabling PMU")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
INV cmd for dcache provides 2 modes discard or wback-before-discard.
One is default and other needs to be set, if so desired. This is common
for line-op/entire-cache-op. So refactor them out into a helper
Doesn't affect generated code but paves way for any common
micro-optimization.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* print aliasing or not, VIPT/PIPT etc
* compress param storage using bitfields
* more use of IS_ENABLED to de-uglify code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Hardware keeps them enabled on reset, and Linux needs to keep status quo.
Any spurious interrupts will be reported/blocked by genirq.
This helps remove a SMP IRQ quirk (next commit), where a peripheral IRQ
is hard wired to core0, and request_irq()->unmask() happens on core1,
keeping the IRQ masked on core0, needing an explicit unmask.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current cpu-private IRQ registration is ugly as it requires need to
expose arch_unmask_irq() outside of intc code.
So switch to percpu IRQ APIs:
-request_percpu_irq [boot core]
-enable_percpu_irq [all cores]
Encapsulated in helper arc_request_percpu_irq()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adding IS_G4X instead of gen < 5 as suggested by Daniel
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
