commit 5e599d73c1 upstream.
This patch improves the way the RDMA IB signalling is done by using atomic
operations for the signalling variable. This avoids race conditions on
sig_count.
The signalling interval changes slightly and is now the largest power of
two not larger than queue depth / 2.
ilog() usage idea by Bart Van Assche.
Signed-off-by: Marta Rybczynska <marta.rybczynska@kalray.eu>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d6dee80a1 upstream.
At the point where the kvm-vfio pseudo device wants to release its
vfio group reference, we can't always acquire a new reference to make
that happen. The group can be in a state where we wouldn't allow a
new reference to be added. This new helper function allows a caller
to match a file to a group to facilitate this. Given a file and
group, report if they match. Thus the caller needs to already have a
group reference to match to the file. This allows the deletion of a
group without acquiring a new reference.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811642d8d8 upstream.
If vfio_iommu_group_notifier() acquires a group reference and that
reference becomes the last reference to the group, then vfio_group_put
introduces a deadlock code path where we're trying to unregister from
the iommu notifier chain from within a callout of that chain. Use a
work_struct to release this reference asynchronously.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4495ec6d77 upstream.
When getting flags, a response to a different message would
result in a deadlock because of a missing unlock. Add that
unlock and a comment. Found by static analysis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdea46566b upstream.
A vendor with a system having more than 128 CPUs occasionally encounters
the following crash during shutdown. This is not an easily reproduceable
event, but the vendor was able to provide the following analysis of the
crash, which exhibits the same footprint each time.
crash> bt
PID: 0 TASK: ffff88017c70ce70 CPU: 5 COMMAND: "swapper/5"
#0 [ffff88085c143ac8] machine_kexec at ffffffff81059c8b
#1 [ffff88085c143b28] __crash_kexec at ffffffff811052e2
#2 [ffff88085c143bf8] crash_kexec at ffffffff811053d0
#3 [ffff88085c143c10] oops_end at ffffffff8168ef88
#4 [ffff88085c143c38] no_context at ffffffff8167ebb3
#5 [ffff88085c143c88] __bad_area_nosemaphore at ffffffff8167ec49
#6 [ffff88085c143cd0] bad_area_nosemaphore at ffffffff8167edb3
#7 [ffff88085c143ce0] __do_page_fault at ffffffff81691d1e
#8 [ffff88085c143d40] do_page_fault at ffffffff81691ec5
#9 [ffff88085c143d70] page_fault at ffffffff8168e188
[exception RIP: unknown or invalid address]
RIP: ffffffffa053c800 RSP: ffff88085c143e28 RFLAGS: 00010206
RAX: ffff88017c72bfd8 RBX: ffff88017a8dc000 RCX: ffff8810588b5ac8
RDX: ffff8810588b5a00 RSI: ffffffffa053c800 RDI: ffff8810588b5a00
RBP: ffff88085c143e58 R8: ffff88017c70d408 R9: ffff88017a8dc000
R10: 0000000000000002 R11: ffff88085c143da0 R12: ffff8810588b5ac8
R13: 0000000000000100 R14: ffffffffa053c800 R15: ffff8810588b5a00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
<IRQ stack>
[exception RIP: cpuidle_enter_state+82]
RIP: ffffffff81514192 RSP: ffff88017c72be50 RFLAGS: 00000202
RAX: 0000001e4c3c6f16 RBX: 000000000000f8a0 RCX: 0000000000000018
RDX: 0000000225c17d03 RSI: ffff88017c72bfd8 RDI: 0000001e4c3c6f16
RBP: ffff88017c72be78 R8: 000000000000237e R9: 0000000000000018
R10: 0000000000002494 R11: 0000000000000001 R12: ffff88017c72be20
R13: ffff88085c14f8e0 R14: 0000000000000082 R15: 0000001e4c3bb400
ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018
This is the corresponding stack trace
It has crashed because the area pointed with RIP extracted from timer
element is already removed during a shutdown process.
The function is smi_timeout().
And we think ffff8810588b5a00 in RDX is a parameter struct smi_info
crash> rd ffff8810588b5a00 20
ffff8810588b5a00: ffff8810588b6000 0000000000000000 .`.X............
ffff8810588b5a10: ffff880853264400 ffffffffa05417e0 .D&S......T.....
ffff8810588b5a20: 24a024a000000000 0000000000000000 .....$.$........
ffff8810588b5a30: 0000000000000000 0000000000000000 ................
ffff8810588b5a30: 0000000000000000 0000000000000000 ................
ffff8810588b5a40: ffffffffa053a040 ffffffffa053a060 @.S.....`.S.....
ffff8810588b5a50: 0000000000000000 0000000100000001 ................
ffff8810588b5a60: 0000000000000000 0000000000000e00 ................
ffff8810588b5a70: ffffffffa053a580 ffffffffa053a6e0 ..S.......S.....
ffff8810588b5a80: ffffffffa053a4a0 ffffffffa053a250 ..S.....P.S.....
ffff8810588b5a90: 0000000500000002 0000000000000000 ................
Unfortunately the top of this area is already detroyed by someone.
But because of two reasonns we think this is struct smi_info
1) The address included in between ffff8810588b5a70 and ffff8810588b5a80:
are inside of ipmi_si_intf.c see crash> module ffff88085779d2c0
2) We've found the area which point this.
It is offset 0x68 of ffff880859df4000
crash> rd ffff880859df4000 100
ffff880859df4000: 0000000000000000 0000000000000001 ................
ffff880859df4010: ffffffffa0535290 dead000000000200 .RS.............
ffff880859df4020: ffff880859df4020 ffff880859df4020 @.Y.... @.Y....
ffff880859df4030: 0000000000000002 0000000000100010 ................
ffff880859df4040: ffff880859df4040 ffff880859df4040 @@.Y....@@.Y....
ffff880859df4050: 0000000000000000 0000000000000000 ................
ffff880859df4060: 0000000000000000 ffff8810588b5a00 .........Z.X....
ffff880859df4070: 0000000000000001 ffff880859df4078 ........x@.Y....
If we regards it as struct ipmi_smi in shutdown process
it looks consistent.
The remedy for this apparent race is affixed below.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was first introduced in 7ea0ed2b5b ipmi: Make the
message handler easier to use for SMI interfaces
where some code was moved outside of the rcu_read_lock()
and the lock was not added.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
commit 564d8a2cf3 upstream.
The late 2009, 27 inch Apple iMac10,1 has an
internal eDP display and an external Mini-
Displayport output, driven by a DCE-3.2, RV730
Radeon Mobility HD-4670.
The machine worked fine in a dual-display setup
with eDP panel + externally connected HDMI
or DVI-D digital display sink, connected via
MiniDP to DVI or HDMI adapter.
However, booting the machine single-display with
only eDP panel results in a completely black
display - even backlight powering off, as soon as
the radeon modesetting driver loads.
This patch fixes the single dispay eDP case by
assigning encoders based on dig->linkb, similar
to DCE-4+. While this should not be generally
necessary (Alex: "...atom on normal boards
should be able to handle any mapping."), Apple
seems to use some special routing here.
One remaining problem not solved by this patch
is that an external Minidisplayport->DP sink
does still not work on iMac10,1, whereas external
DVI and HDMI sinks continue to work.
The problem affects at least all tested kernels
since Linux 3.13 - didn't test earlier kernels, so
backporting to stable probably makes sense.
v2: With the original patch from 2016, Alex was worried it
will break other DCE3.2 systems. Use dmi_match() to
apply this special encoder assignment only for the
Apple iMac 10,1 from late 2009.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab03d9fe50 upstream.
Even if the vblank period would allow it, it still seems to
be problematic on some cards.
v2: fix logic inversion (Nils)
bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9156e72330 upstream.
If you initiate a read that is out of the VRAM address space return
ENXIO instead of 0.
Reads that begin below that point will read upto the VRAM limit as
before.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d27718f3 upstream.
The raid5 md device is created by the disks which we don't use the total size. For example,
the size of the device is 5G and it just uses 3G of the devices to create one raid5 device.
Then change the chunksize and wait reshape to finish. After reshape finishing stop the raid
and assemble it again. It fails.
mdadm -CR /dev/md0 -l5 -n3 /dev/loop[0-2] --size=3G --chunk=32 --assume-clean
mdadm /dev/md0 --grow --chunk=64
wait reshape to finish
mdadm -S /dev/md0
mdadm -As
The error messages:
[197519.814302] md: loop1 does not have a valid v1.2 superblock, not importing!
[197519.821686] md: md_import_device returned -22
After reshape the data offset is changed. It selects backwards direction in this condition.
In function super_1_load it compares the available space of the underlying device with
sb->data_size. The new data offset gets bigger after reshape. So super_1_load returns -EINVAL.
rdev->sectors is updated in md_finish_reshape. Then sb->data_size is set in super_1_sync based
on rdev->sectors. So add md_finish_reshape in end_reshape.
Signed-off-by: Xiao Ni <xni@redhat.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e3f0701f2 upstream.
__add_badblock_range() does not account sector alignment when
it sets 'num_sectors'. Therefore, an ARS error record range
spanning across two sectors is set to a single sector length,
which leaves the 2nd sector unprotected.
Change __add_badblock_range() to set 'num_sectors' properly.
Fixes: 0caeef63e6 ("libnvdimm: Add a poison list and export badblocks")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c13c43d54f upstream.
btt_rw_page was not propagating errors frm btt_do_bvec, resulting in any
IO errors via the rw_page path going unnoticed. the pmem driver recently
fixed this in e10624f pmem: fail io-requests to known bad blocks
but same problem in BTT went neglected.
Fixes: 5212e11fde ("nd_btt: atomic sector updates")
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e0973a918 upstream.
Setting initial standard at the top of cx8800_initdev would cause the
first call to cx88_set_tvnorm() to return without programming any
registers (leaving the driver saying it's set to NTSC but the hardware
isn't programmed). Even worse, any subsequent attempt to explicitly
set it to NTSC-M will return success but actually fail to program the
underlying registers unless first changing the standard to something
other than NTSC-M.
Set the initial standard later in the process, and make sure the field
is zero at the beginning to ensure that the call always goes through.
This regression was introduced in the following commit:
commit ccd6f1d488 ("[media] cx88: move width, height and field to core
struct")
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] cx88: move width, height and field to core struct
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c79bc05a upstream.
The function flush_signals clears all pending signals for the process. It
may be used by kernel threads when we need to prepare a kernel thread for
responding to signals. However using this function for an userspaces
processes is incorrect - clearing signals without the program expecting it
can cause misbehavior.
The raid1 and raid5 code uses flush_signals in its request routine because
it wants to prepare for an interruptible wait. This patch drops
flush_signals and uses sigprocmask instead to block all signals (including
SIGKILL) around the schedule() call. The signals are not lost, but the
schedule() call won't respond to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8b9c974af upstream.
A gadget driver will not disable eps immediately when ->disconnect()
is called. But, since this driver assumes all eps stop after
the ->disconnect(), unexpected behavior happens (especially in system
suspend).
So, this patch disables all eps in usbhsg_try_stop(). After disabling
eps by renesas_usbhs driver, since some functions will be called by
both a gadget and renesas_usbhs driver, renesas_usbhs driver should
protect uep->pipe. To protect uep->pipe easily, this patch adds a new
lock in struct usbhsg_uep.
Fixes: 2f98382dc ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59a0879a0e upstream.
This patch fixes an issue that some registers may be not initialized
after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise,
if a cable is not connected, the driver will not enable INTENB0.VBSE
after resume. And then, the driver cannot detect the VBUS.
Fixes: ca8a282a53 ("usb: gadget: renesas_usbhs: add suspend/resume support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 446230f52a upstream.
When us->extra is null the driver is not initialized, however, a
later call to osd200_scsi_to_ata is made that dereferences
us->extra, causing a null pointer dereference. The code
currently detects and reports that the driver is not initialized;
add a return to avoid the subsequent dereference issue in this
check.
Thanks to Alan Stern for pointing out that srb->result needs setting
to DID_ERROR << 16
Detected by CoverityScan, CID#100308 ("Dereference after null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d90b336f3f upstream.
The recent changes in 4.9 to mandate USB buffers be heap allocated
broke this driver, which was allocating the buffers on the stack.
This resulted in the device failing at initialization.
Introduce dedicated send/receive buffers as part of the state
structure, and add a mutex to protect access to them.
Note: we also had to tweak the API to mxl111sf_ctrl_msg to pass
the pointer to the state struct rather than the device, since
we need it inside the function to access the buffers and the
mutex. This patch adjusts the callers to match the API change.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reported-by: Doug Lung <dlung0@gmail.com>
Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9da5a1092b upstream.
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b895868bb upstream.
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a54408d0a0 upstream.
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60514bd44 upstream.
Currently we saw a lot of "No irq handler" errors during hibernation, which
caused the system hang finally:
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
do_IRQ: 31.151 No irq handler for vector
According to above logs, there is an interrupt triggered and it is
dispatched to CPU31 with a vector number 151, but there is no handler for
it, thus this IRQ will not get acked and will cause an IRQ flood which
kills the system. To be more specific, the 31.151 is an interrupt from the
AHCI host controller.
After some investigation, the reason why this issue is triggered is because
the thaw_noirq() function does not restore the MSI/MSI-X settings across
hibernation.
The scenario is illustrated below:
1. Before hibernation, IRQ 34 is the handler for the AHCI device, which
is bound to CPU31.
2. Hibernation starts, the AHCI device is put into low power state.
3. All the nonboot CPUs are put offline, so IRQ 34 has to be migrated to
the last alive one - CPU0.
4. After the snapshot has been created, all the nonboot CPUs are brought
up again; IRQ 34 remains bound to CPU0.
5. AHCI devices are put into D0.
6. The snapshot is written to the disk.
The issue is triggered in step 6. The AHCI interrupt should be delivered
to CPU0, however it is delivered to the original CPU31 instead, which
causes the "No irq handler" issue.
Ying Huang has provided a clue that, in step 3 it is possible that writing
to the register might not take effect as the PCI devices have been
suspended.
In step 3, the IRQ 34 affinity should be modified from CPU31 to CPU0, but
in fact it is not. In __pci_write_msi_msg(), if the device is already in
low power state, the low level MSI message entry will not be updated but
cached. During the device restore process after a normal suspend/resume,
pci_restore_msi_state() writes the cached MSI back to the hardware.
But this is not the case for hibernation. pci_restore_msi_state() is not
currently called in pci_pm_thaw_noirq(), although pci_save_state() has
saved the necessary PCI cached information in pci_pm_freeze_noirq().
Restore the PCI status for the device during hibernation. Otherwise the
status might be lost across hibernation (for example, settings for MSI,
MSI-X, ATS, ACS, IOV, etc.), which might cause problems during hibernation.
Suggested-by: Ying Huang <ying.huang@intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: Ying Huang <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc8cca5ef2 upstream.
Rockchip's RC has two banks of registers for the root port: a normal bank
that is strictly compatible with the PCIe spec, and a privileged bank that
can be used to change RO bits of root port registers.
When probing the RC driver, we use the privileged bank to do some basic
setup work as some RO bits are hw-inited to wrong value. But we didn't
change to the normal bank after probing the driver.
This leads to a serious problem when the PME code tries to clear the PME
status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per
PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code
is doing the right thing to clear the PME status but we find the RC doesn't
clear it but actually setting it to one. So finally the system trap in
pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue
can be reproduced by booting kernel with pci=nomsi.
Use the normal register bank for the PCI config accessors. The privileged
bank is used only internally by this driver.
Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f4ab18ac5 upstream.
scsiback_release_cmd() must not dereference se_cmd->se_tmr_req
because that memory is freed by target_free_cmd_mem() before
scsiback_release_cmd() is called. Fix this use-after-free by
inlining struct scsiback_tmr into struct vscsibk_pend.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: David Disseldorp <ddiss@suse.de>
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 138d351eef upstream.
This patch re-introduces part of a long standing login workaround that
was recently dropped by:
commit 1c99de981f
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Sun Apr 2 13:36:44 2017 -0700
iscsi-target: Drop work-around for legacy GlobalSAN initiator
Namely, the workaround for FirstBurstLength ended up being required by
Mellanox Flexboot PXE boot ROMs as reported by Robert.
So this patch re-adds the work-around for FirstBurstLength within
iscsi_check_proposer_for_optional_reply(), and makes the key optional
to respond when the initiator does not propose, nor respond to it.
Also as requested by Arun, this patch introduces a new TPG attribute
named 'login_keys_workaround' that controls the use of both the
FirstBurstLength workaround, as well as the two other existing
workarounds for gPXE iSCSI boot client.
By default, the workaround is enabled with login_keys_workaround=1,
since Mellanox FlexBoot requires it, and Arun has verified the Qlogic
MSFT initiator already proposes FirstBurstLength, so it's uneffected
by this re-adding this part of the original work-around.
Reported-by: Robert LeBlanc <robert@leblancnet.us>
Cc: Robert LeBlanc <robert@leblancnet.us>
Reviewed-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9279c968c upstream.
The addition of the STARGET_REMOVE state had the side effect of
introducing a race condition that can cause a crash.
scsi_target_reap_ref_release() checks the starget->state to
see if it still in STARGET_CREATED, and if so, skips calling
transport_remove_device() and device_del(), because the starget->state
is only set to STARGET_RUNNING after scsi_target_add() has called
device_add() and transport_add_device().
However, if an rport loss occurs while a target is being scanned,
it can happen that scsi_remove_target() will be called while the
starget is still in the STARGET_CREATED state. In this case, the
starget->state will be set to STARGET_REMOVE, and as a result,
scsi_target_reap_ref_release() will take the wrong path. The end
result is a panic:
[ 1255.356653] Oops: 0000 [#1] SMP
[ 1255.360154] Modules linked in: x86_pkg_temp_thermal kvm_intel kvm irqbypass crc32c_intel ghash_clmulni_i
[ 1255.393234] CPU: 5 PID: 149 Comm: kworker/u96:4 Tainted: G W 4.11.0+ #8
[ 1255.401879] Hardware name: Dell Inc. PowerEdge R320/08VT7V, BIOS 2.0.22 11/19/2013
[ 1255.410327] Workqueue: scsi_wq_6 fc_scsi_scan_rport [scsi_transport_fc]
[ 1255.417720] task: ffff88060ca8c8c0 task.stack: ffffc900048a8000
[ 1255.424331] RIP: 0010:kernfs_find_ns+0x13/0xc0
[ 1255.429287] RSP: 0018:ffffc900048abbf0 EFLAGS: 00010246
[ 1255.435123] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 1255.443083] RDX: 0000000000000000 RSI: ffffffff8188d659 RDI: 0000000000000000
[ 1255.451043] RBP: ffffc900048abc10 R08: 0000000000000000 R09: 0000012433fe0025
[ 1255.459005] R10: 0000000025e5a4b5 R11: 0000000025e5a4b5 R12: ffffffff8188d659
[ 1255.466972] R13: 0000000000000000 R14: ffff8805f55e5088 R15: 0000000000000000
[ 1255.474931] FS: 0000000000000000(0000) GS:ffff880616b40000(0000) knlGS:0000000000000000
[ 1255.483959] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1255.490370] CR2: 0000000000000068 CR3: 0000000001c09000 CR4: 00000000000406e0
[ 1255.498332] Call Trace:
[ 1255.501058] kernfs_find_and_get_ns+0x31/0x60
[ 1255.505916] sysfs_unmerge_group+0x1d/0x60
[ 1255.510498] dpm_sysfs_remove+0x22/0x60
[ 1255.514783] device_del+0xf4/0x2e0
[ 1255.518577] ? device_remove_file+0x19/0x20
[ 1255.523241] attribute_container_class_device_del+0x1a/0x20
[ 1255.529457] transport_remove_classdev+0x4e/0x60
[ 1255.534607] ? transport_add_class_device+0x40/0x40
[ 1255.540046] attribute_container_device_trigger+0xb0/0xc0
[ 1255.546069] transport_remove_device+0x15/0x20
[ 1255.551025] scsi_target_reap_ref_release+0x25/0x40
[ 1255.556467] scsi_target_reap+0x2e/0x40
[ 1255.560744] __scsi_scan_target+0xaa/0x5b0
[ 1255.565312] scsi_scan_target+0xec/0x100
[ 1255.569689] fc_scsi_scan_rport+0xb1/0xc0 [scsi_transport_fc]
[ 1255.576099] process_one_work+0x14b/0x390
[ 1255.580569] worker_thread+0x4b/0x390
[ 1255.584651] kthread+0x109/0x140
[ 1255.588251] ? rescuer_thread+0x330/0x330
[ 1255.592730] ? kthread_park+0x60/0x60
[ 1255.596815] ret_from_fork+0x29/0x40
[ 1255.600801] Code: 24 08 48 83 42 40 01 5b 41 5c 5d c3 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90
[ 1255.621876] RIP: kernfs_find_ns+0x13/0xc0 RSP: ffffc900048abbf0
[ 1255.628479] CR2: 0000000000000068
[ 1255.632756] ---[ end trace 34a69ba0477d036f ]---
Fix this by adding another scsi_target state STARGET_CREATED_REMOVE
to distinguish this case.
Fixes: f05795d3d7 ("scsi: Add intermediate STARGET_REMOVE state to scsi_target_state")
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e62ffd95 upstream.
The enclosure_add_device() function should fail if it can't create the
relevant sysfs links.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Acked-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e2d1bce4 upstream.
of_genpd_remove_last() iterates over list of domains and removes
matching element thus it has to use safe version of list iteration.
Fixes: 17926551c9 (PM / Domains: Add support for removing nested PM domains by provider)
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b556b15dc0 upstream.
of_genpd_del_provider() iterates over list of domain provides and
removes matching element thus it has to use safe version of list
iteration.
Fixes: aa42240ab2 (PM / Domains: Add generic OF-based PM domain look-up)
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6e83cac3e upstream.
pm_genpd_remove_subdomain() iterates over domain's master_links list and
removes matching element thus it has to use safe version of list
iteration.
Fixes: f721889ff6 ("PM / Domains: Support for generic I/O PM domains (v8)")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 440aeca4b9 upstream.
The functions igb_read_phy_reg_gs40g/igb_write_phy_reg_gs40g (which were
removed in 2a3cdea) explicitly selected the required page at every phy_reg
access. Currently, igb_get_phy_id_82575 relays on the fact that page 0 is
already selected. The assumption is not fulfilled for my Lex 3I380CW
motherboard with integrated dual i211 based gigabit ethernet. This leads to igb
initialization failure and network interfaces are not working:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
igb: probe of 0000:02:00.0 failed with error -2
In order to fix it, we explicitly select page 0 before first access to phy
registers.
See also: https://bugzilla.suse.com/show_bug.cgi?id=1009911
See also: http://www.lex.com.tw/products/pdf/3I380A&3I380CW.pdf
Fixes: 2a3cdea ("igb: Remove GS40G specific defines/functions")
Signed-off-by: Matwey V Kornilov <matwey@sai.msu.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a4274bf2d upstream.
In the stable linux-3.16 branch, I ran into a warning in the
wlcore driver:
drivers/net/wireless/ti/wlcore/spi.c: In function 'wl12xx_spi_raw_write':
drivers/net/wireless/ti/wlcore/spi.c:315:1: error: the frame size of 12848 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Newer kernels no longer show the warning, but the bug is still there,
as the allocation is based on the CPU page size rather than the
actual capabilities of the hardware.
This replaces the PAGE_SIZE macro with the SZ_4K macro, i.e. 4096 bytes
per buffer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45dd39b974 upstream.
The nci-device was never deregistered in the event that
fw-initialisation failed.
Fix this by moving the firmware initialisation before device
registration since the firmware work queue should be available before
registering.
Note that this depends on a recent fix that moved device-name
initialisation back to to nci_allocate_device() as the
firmware-workqueue name is now derived from the nfc-device name.
Fixes: 3194c68701 ("NFC: nfcmrvl: add firmware download support")
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5834ac229 upstream.
Use the nfc- rather than phy-device in firmware-management code that
needs a valid struct device.
This specifically fixes a NULL-pointer dereference in
nfcmrvl_fw_dnld_init() during registration when the underlying tty is
one end of a Unix98 pty.
Note that the driver still uses the phy device for any debugging, which
is fine for now.
Fixes: 3194c68701 ("NFC: nfcmrvl: add firmware download support")
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cbe40112f upstream.
This specifically fixes resource leaks in the registration error paths.
Device-managed resources is a bad fit for this driver as devices can be
registered from the n_nci line discipline. Firstly, a tty may not even
have a corresponding device (should it be part of a Unix98 pty)
something which would lead to a NULL-pointer dereference when
registering resources.
Secondly, if the tty has a class device, its lifetime exceeds that of
the line discipline, which means that resources would leak every time
the line discipline is closed (or if registration fails).
Currently, the devres interface was only being used to request a reset
gpio despite the fact that it was already explicitly freed in
nfcmrvl_nci_unregister_dev() (along with the private data), something
which also prevented the resource leak at close.
Note that the driver treats gpio number 0 as invalid despite it being
perfectly valid. This will be addressed in a follow-up patch.
Fixes: b2fe288eac ("NFC: nfcmrvl: free reset gpio")
Fixes: 4a2b947f56 ("NFC: nfcmrvl: add chip reset management")
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e0c59f15 upstream.
Make sure to check the tty-device pointer before trying to access the
parent device to avoid dereferencing a NULL-pointer when the tty is one
end of a Unix98 pty.
Fixes: e097dc624f ("NFC: nfcmrvl: add UART driver")
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde717ab47 upstream.
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf8ce1ea61 upstream.
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 289d72afdd upstream.
After the lock is dropped, it is possible that the cpufreq_dev gets
freed before we call get_level() and that can cause kernel to crash.
Drop the lock after we are done using the structure.
Fixes: 02373d7c69 ("thermal: cpu_cooling: fix lockdep problems in cpu_cooling")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c592fafbdb upstream.
The thermal child device reuses the parent MFD-device device-tree node
when registering a thermal zone, but did not take a reference to the
node.
This leads to a reference imbalance, and potential use-after-free, when
the node reference is dropped by the platform-bus device destructor
(once for the child and later again for the parent).
Fix this by dropping any reference already held to a device-tree node
and getting a reference to the parent's node which will be balanced on
reprobe or on platform-device release, whichever comes first.
Note that simply clearing the of_node pointer on probe errors and on
driver unbind would not allow the use of device-managed resources as
specifically thermal_zone_of_sensor_unregister() claims that a valid
device-tree node pointer is needed during deregistration (even if it
currently does not seem to use it).
Fixes: ec4664b3fd ("thermal: max77620: Add thermal driver for reporting junction temp")
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a16e37726c upstream.
Gcc 7.1 complains about:
drivers/media/platform/s5p-jpeg/jpeg-core.c: In function 's5p_jpeg_parse_hdr.isra.9':
drivers/media/platform/s5p-jpeg/jpeg-core.c:1207:12: warning: 'width' may be used uninitialized in this function [-Wmaybe-uninitialized]
result->w = width;
~~~~~~~~~~^~~~~~~
drivers/media/platform/s5p-jpeg/jpeg-core.c:1208:12: warning: 'height' may be used uninitialized in this function [-Wmaybe-uninitialized]
result->h = height;
~~~~~~~~~~^~~~~~~~
Indeed the code would allow it to return a random value (although
it shouldn't happen, in practice). So, explicitly set both to zero,
just in case.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7e31bbad upstream.
gcc-7 suggests that an expression using a bitwise not and a bitmask
on a 'bool' variable is better written using boolean logic:
drivers/media/rc/imon.c: In function 'imon_incoming_scancode':
drivers/media/rc/imon.c:1725:22: error: '~' on a boolean expression [-Werror=bool-operation]
ictx->pad_mouse = ~(ictx->pad_mouse) & 0x1;
^
drivers/media/rc/imon.c:1725:22: note: did you mean to use logical not?
I agree.
Fixes: 21677cfc56 ("V4L/DVB: ir-core: add imon driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ca30331c1 upstream.
In the current code, if the user accidentally writes a bogus command to
this sysfs file, then we set the latency tolerance to an uninitialized
variable.
Fixes: 2d984ad132 (PM / QoS: Introcuce latency tolerance device PM QoS type)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea0212f40c upstream.
The wakeirq infrastructure uses RCU to protect the list of wakeirqs. That
breaks the irq bus locking infrastructure, which is allows sleeping
functions to be called so interrupt controllers behind slow busses,
e.g. i2c, can be handled.
The wakeirq functions hold rcu_read_lock and call into irq functions, which
in case of interrupts using the irq bus locking will trigger a
might_sleep() splat.
Convert the wakeirq infrastructure to Sleepable RCU and unbreak it.
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Reported-by: Brian Norris <briannorris@chromium.org>
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7459e1d25f upstream.
Driver does not properly handle the case when signals interrupt
wait_for_completion_interruptible():
-it does not check for return value
-completion structure is allocated on stack; in case a signal interrupts
the sleep, it will go out of scope, causing the worker thread
(caam_jr_dequeue) to fail when it accesses it
wait_for_completion_interruptible() is replaced with uninterruptable
wait_for_completion().
We choose to block all signals while waiting for I/O (device executing
the split key generation job descriptor) since the alternative - in
order to have a deterministic device state - would be to flush the job
ring (aborting *all* in-progress jobs).
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Fixes: 4c1ec1f930 ("crypto: caam - refactor key_gen, sg")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 854b06f768 upstream.
Certain cipher modes like CTS expect the IV (req->info) of
ablkcipher_request (or equivalently req->iv of skcipher_request) to
contain the last ciphertext block when the {en,de}crypt operation is done.
This is currently not the case for the CAAM driver which in turn breaks
e.g. cts(cbc(aes)) when the CAAM driver is enabled.
This patch fixes the CAAM driver to properly set the IV after the
{en,de}crypt operation of ablkcipher finishes.
This issue was revealed by the changes in the SW CTS mode in commit
0605c41cc5 ("crypto: cts - Convert to skcipher")
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1606043f21 upstream.
The Atmel SHA driver was treating -EBUSY as indication of queueing
to backlog without checking that backlog is enabled for the request.
Fix it by checking request flags.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
