The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-35-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-34-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-33-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-32-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-31-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
There won't be any new entries, nor are the entries that much different
and the very odd page and sector sizes make the new format hard to read.
Therefore, convert the old S3AN_INFO() macro.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-29-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
After all the preparation, it is now time to introduce the new macros to
specify flashes in our database: SNOR_ID() and SNOR_OTP(). An flash_info
entry might now look like:
{
.id = SNOR_ID(0xef, 0x60, 0x16),
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
.flags = SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB,
}
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-15-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Move the OTP ops out of the flash_info structure. Besides of saving some
space, there will be a new macro SNOR_OTP() which can be used to set the
ops:
.otp = SNOR_OTP(...),
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-14-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Create a new structure to hold a flash ID and its length. The goal is to
have a new macro SNOR_ID() which can have a flexible id length. This way
we can get rid of all the individual INFOx() macros.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-13-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The id will be converted to an own structure. To differentiate between
flashes with and without IDs, introduce a temporary macro INFO0() and
convert all flashes with no ID to use it. The difference between INFO0()
and INFOx() is that the former, doesn't have a pointer to the id
structure. Something which isn't possible to do within the INFOx()
macro.
After the flash_info conversion, that macro will be removed along with
all the other INFOx() macros.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-12-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Drop the size parameter to indicate we need to do SFDP, we can do that
because it is guaranteed that the size will be set by SFDP and because
PARSE_SFDP forced the SFDP parsing it must be overwritten.
There is a (very tiny) chance that this might break block protection
support: we now rely on the SFDP reported size of the flash for the
BP calculation. OTOH, if the flash reports its size wrong, we are
in bigger trouble than just having the BP calculation wrong.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-11-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Most of the (old, non-SFDP) flashes use a sector size of 64k. Make that
a default value so it can be optional in the flash_info database.
As a preparation for conversion to the new database format, set the
sector size to zero if the default value is used. This way, the actual
change is happening with this patch ant not with a later conversion
patch.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-10-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
4k sector erase sizes are only a thing with uniform erase types. Push
the "we want 4k erase sizes" handling into spi_nor_select_uniform_erase().
One might wonder why the former sector_size isn't used anymore. It is
because we either search for the largest erase size or if selected
through kconfig, the 4k erase size. Now, why is that correct? For this,
we have to differentiate between (1) flashes with SFDP and (2) without
SFDP. For (1), we just set one (or two if SECT_4K is set) erase types
and wanted_size is exactly one of these.
For (2) things are a bit more complicated. For flashes which we don't
have in our flash_info database, the generic driver is used and
sector_size was already 0, which in turn selected the largest erase
size. For flashes which had SFDP and an entry in flash_info, sector_size
was always the largest sector and thus the largest erase type.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-9-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
If .n_banks is not set in the flash_info database, the default value
should be 1. This way, we don't have to always set the .n_banks
parameter in flash_info.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-8-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
First, fixups might want to replace the n_banks parameter, thus we need
it in the (writable) parameter struct. Secondly, this way we can have a
default in the core and just skip setting the n_banks in the flash_info
database. Most of the flashes doesn't have more than one bank.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-7-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The INFO() macro always set the page_size to 256 bytes. Make that an
optional parameter. This default is a sane one for all older flashes,
newer ones will set the page size by its SFDP tables anyway.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-6-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
.n_sectors is rarely used. In fact it is only used in swp.c and to
calculate the flash size in the core. The use in swp.c might be
converted to use the (largest) flash erase size. For now, we just
locally calculate the sector size.
Simplify the flash_info database and set the size of the flash directly.
This also let us use the SZ_x macros.
Verified that there's no flash that specifies BP and sector size of zero
to make sure we avoid a division by zero in
spi_nor_get_min_prot_length_sr(). We'll protect from a possible division
by zero in a further patch by introducing a default value for
sector_size.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-5-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
In commit 5927318029 ("mtd: spi-nor: Create macros to define chip IDs
and geometries") SPI_NOR_ID() were introduced, but it did only update
the INFO() macro in core.h. Also use it in S3AN_INFO().
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-3-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
This part is not a flash but an EEPROM like FRAM. It is even has a DT
binding for the (correct) driver (at25), see
Documentation/devicetree/bindings/eeprom/at25.yaml. Just remove it.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-2-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
CAT25xx are actually EEPROMs manufactured by Catalyst. The devices are
ancient (DS are from 1998), there are not in-tree users, nor are there
any device tree bindings. Remove it. The correct driver is the at25.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-1-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6💿11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit c3f853184b ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that
is always false") fixed a no-op BUG_ON. This turned out to cause a
regression, since some in-tree device-tree files already use
LED_COLOR_ID_MULTI.
Drop the BUG_ON altogether.
Fixes: c3f853184b ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false")
Reported-by: Da Xue <da@libre.computer>
Closes: https://lore.kernel.org/linux-leds/ZQLelWcNjjp2xndY@duo.ucw.cz/T/
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230918140724.18634-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
MFD_CS42L43 depends on REGMAP_IRQ as it uses devm_regmap_add_irq_chip.
Otherwise the build may fail with following log.
AR drivers/built-in.a
AR built-in.a
AR vmlinux.a
LD vmlinux.o
OBJCOPY modules.builtin.modinfo
GEN modules.builtin
MODPOST Module.symvers
ERROR: modpost: "devm_regmap_add_irq_chip" [drivers/mfd/cs42l43.ko] undefined!
Fixes: ace6d14481 ("mfd: cs42l43: Add support for cs42l43 core driver")
Signed-off-by: Woody Zhang <woodylab@foxmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/tencent_E54C7156F583E15FFE320E576E3389C39A08@qq.com
Signed-off-by: Lee Jones <lee@kernel.org>
New platform SSID:0x231f.
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing.
So, it needs to swap DAC.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/8d63c6e360124e3ea2523753050e6f05@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA patch loader is supported by legacy HDA driver. Implement it on
ASoC HDA driver, too.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230919083209.1919921-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF stack now uses the generic names for the IPC type, the defines can
be dropped.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new SOF_IPC_TYPE_3 in core code.
No functional changes, just renaming.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new SOF_IPC_TYPE_3, SOF_IPC_TYPE_4 in core code.
No functional changes, just renaming.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new SOF_IPC_TYPE_3 in core code.
No functional changes, just renaming.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new SOF_IPC_TYPE_3 in core code.
No functional changes, just renaming.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new SOF_IPC_TYPE_3, SOF_IPC_TYPE_4 in core code.
No functional changes, just renaming.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the Intel from the IPC type Kconfig option
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230919104226.32239-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>