access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This is used only once by ath9k_hw_process_ini() to
write an array of phy registers through REG_WRITE_ARRAY(),
but we already call REG_WRITE_ARRAY() multiple times
on the same caller so just remove this pointless wrapper.
We'll eventually just move the ath9k_hw_process_ini()
caller as an callback to abstract away between different
hardware families.
Although this change is subtle I should note that this
does change the delay pattern on writing the next series
of registers. REG_WRITE_ARRAY() uses a counter for each
register write and does a udelay(1) every 64 writes. By
removing this call it means that the counter is processed
for all the iniBB_RfGain registers and is incremented
on ath9k_hw_process_ini(), before this the after the call
ath9k_hw_write_regs() was made the register counter was
kept at the same index number prior to the call.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 does not have a reset control for AHB.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a stable code fix as this register is not used anywhere.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 will be the first device supported of the AR9003
family. AR9300 1.0 hardware exists but it is not going to
be sold anywhere so we completely skip its support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR5008, AR9001 and AR9002 family of Atheros
chipsets, all 802.11n. The new breed of 802.11n chips, the
AR9003 family will be supported as well soon. To help with its
support we're going to add a few callbacks for hardware routines
which differ considerably instead of adding branch checks for
the revision at runtime.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Davinci platforms apparently need more time in-between helper firmware
blocks. Even though this is an increased delay, we only take this hit
once at initialization time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate a bunch of C&P code that waits for the firmware to be ready.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for new rtl818x devices, move the existing rtl818x configuration
into the rtl818x directory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 is embedded chip that can be connected using SDIO bus, and is not
an actual SDIO card. For this reason there is a need to pass some board
specific data, like 'EEPROM is attached' flag or power control callback.
However currently there is no way to pass this data through SDIO subsystem,
so this patch registers dummy platform_device to allow that, until we
have a better solution to this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug which was just recently introduced by
("p54pci: prevent stuck rx-ring on slow system").
make M=drivers/net/wireless/p54 C=2 CF=-D__CHECK_ENDIAN__
CHECK drivers/net/wireless/p54/p54pci.c
drivers/net/wireless/p54/p54pci.c:143:11: warning: cast to restricted __le32
CC [M] drivers/net/wireless/p54/p54pci.o
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci used the callback write_tx_desc to write the tx descriptor but
also to update the txwi which is part of the dma mapped skb. Since the
memory was already DMA mapped _before_ the call to write_tx_desc the
device didn't get the txwi data at all or only sporadically.
The call order is basically as follows (from rt2x00queue.c):
1) write_tx_data
2) rt2x00queue_map_txskb
3) write_tx_desc
Hence, we shouldn't touch the skb in write_tx_desc anymore.
To fix this issue create a new rt2800pci_write_tx_data callback and use it
for updating the txwi _before_ the memory gets DMA mapped.
The tx descriptor is still written (as before) in write_tx_desc.
This patch allows basic TX on an rt305x soc device but I'm pretty sure
that it will fix pci based cards as well. I can associate just fine with
an AP now but I wasn't able to get a wpa secured connection working yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some wl1251 hardware configurations (like in WG7210 module) have
EEPROM attached where NVS data is kept, which includes MAC address.
In such configurations, let's read default MAC address from EEPROM,
instead of using random one.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add function prototypes for power management events so they can be
handled and used by platform implementations.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This enables shared IRQs and other features to be used with platform devices
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - switch mode upon system resume
Revert "Input: wacom - merge out and in prox events"
Input: matrix_keypad - allow platform to disable key autorepeat
Input: ALPS - add signature for HP Pavilion dm3 laptops
Input: i8042 - spelling fix
Input: sparse-keymap - implement safer freeing of the keymap
Input: update the status of the Multitouch X driver project
Input: clarify the no-finger event in multitouch protocol
Input: bcm5974 - retract efi-broken suspend_resume
Input: sparse-keymap - free the right keymap on error
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: Anton Anikin <Anton@Anikin.name>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Size needs to be calculated after manipulating with the start value.
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).
CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that the timer IRQs and IPIs aren't enabled for IRQ balancing.
IPIs are disabled as a result of being percpu while the timers simply
disable balancing outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ixgbe driver was setting up 82598 hardware correctly, so that
when promiscuous mode was enabled hardware stripping was turned
off. But on 82599 the logic to disable/enable hardware stripping
is different, and the code was not updated correctly when the
hardware vlan stripping was enabled as default.
This change comprises the creation of two new helper functions
and calling them from the right locations to disable and enable
hardware stripping of vlan tags at appropriate times.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for the Cando dual touch panels, found in the Lenovo S10-3t.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Tested-by: Priya Vijayan <priya.vijayan@intel.com>
Tested-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a straightforward driver for the ST-Ericsson DMA40 DMA
controller found in U8500, implemented akin to the existing
COH 901 318 driver.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidh Kasagar <srinidhi.kasagar@stericsson.com>
Cc: STEricsson_nomadik_linux@list.st.com
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
CC: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If EEPROM is used, NVS data is now loaded but ignored.
Stop loading it to avoid need of dummy NVS file for modules with EEPROM.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register out path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register in path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_hif_usb_alloc_rx_urbs, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skbs allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get RXORN interrupts when all receive buffers are full. This is not
necessarily a fatal situation. It can also happen when the bus is busy or the
CPU is not fast enough to process all frames.
Older chipsets apparently need a reset to come out of this situration, but on
newer chips we can treat RXORN like RX, as going thru a full reset does more
harm than good, there.
The exact chip revisions which need a reset are unknown - this guess
AR5K_SREV_AR5212 ("venice") is copied from the HAL.
Inspired by openwrt 413-rxorn.patch:
"treat rxorn like rx, reset after rxorn seems to do more harm than good"
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a confusion in the usage of the bits AR5K_STA_ID1_ACKCTS_6MB and
AR5K_STA_ID1_BASE_RATE_11B. If they are set (1), we will get lower bitrates for
ACK and CTS. Therefore ath5k_hw_set_ack_bitrate_high(ah, false) actually
resulted in high bitrates, which i think is what we want anyways. Cleared the
confusion and added some documentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduce the field f_max into the mmci_platform_data,
making it possible to pass in a desired block clocking frequency
from a board configuration. This is often more desirable than
using a module parameter. We keep the module parameter as a
fallback as well as the default frequency specified for this
parameter if a parameter is not provided.
This also adds some kerneldoc style documentation to the
platform data struct in mmci.h.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for an 8bit wide bus to the card (data lines
MCIDAT0 through 7 exist) on the ST Micro version and alters the
U300 platform to support this. Also add some ST_ prefix to the
ST-specific registers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 074835f014 ("intel-iommu: Fix
kernel hand if interrupt remapping disabled in BIOS") is adding a check
for interrupt remapping disabled and is dereferencing the dmar_tbl
pointer without checking its value.
Unfortunately, this value is null when booting inside a 64bit virtual
box guest with io-apic disabled, leading to a crash. With a check on it,
the guest is now booting. It's triggering a WARN() in
clockevent_delta2ns but it's better than not booting at all and allows
the user to see there's something wrong on their io-apic setup.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
