spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().
Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit 18c6182bae ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.
This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.
This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.
[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975
Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For no-mmu systems mmap() on RAM/ROM devices already works
but for systems with mmu it probably was not tested and
doesn't work.
This patch allows using mmap() on MTD RAM/ROM devices on systems
with MMU. It has been tested on mpc5121e based platform with
MR0A16A MRAM device attached over LocalBus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for static flash partitioning from a platform
device. Also, we clean up some weirdness where statements were separated
by commas instead of semicolons. While we are at it, fix some minor bad
white space, too.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtd layer is responsible to call mtd->{suspend,resume}. Doing it
again in the driver is wrong and results in a warning:
nand_resume called for a chip which is not in suspended state
at resume time. Removing the calls from the resume and suspend
functions makes them empty allowing them to be deleted completely.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The variable 'syn' was being used uninitialized. Also
fixed incorrect use of syn[] vs s[].
Tested on powerpc board with 64MiB DOC2000.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use own chip_probe function.
Don't touch the memory configuration at probe time.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on.
To use this feature, introduce the chip_probe function.
Also remove workaround for Samsung SoCs.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
EDAC MC3: CE page 0xc32281, offset 0x8a0, grain 0, syndrome 0x1, row 2, channel 1, label "": amd64_edac
EDAC MC3: CE - no information available: amd64_edacError Overflow
Add the missing space before "Error Overflow" on the second line.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Some SH-Mobile SoCs have an HDMI controller and a PHY, attached to one of their
LCDC interfaces. This patch adds a preliminary static support for such
controllers, this means, that only the 720p mode is handled ATM. Support for
more modes and a dynamic switching between them will be added by a follow up
patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
HDMI support for the sh_mobile_lcdc framebuffer driver will require a 'struct
fb_info *' pointer for its .display_on() callback. While at it fix kfr2r09
framebuffer modular build.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for reparenting of div6 clocks on SuperH and SH-Mobile SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh_mobile_lcdc_setup_clocks() can perform IO, therefore it has to be called
after ioremap(). Also check return code of ioremap() and use resource_size()
instead of open-coding it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow platform code to specify callbcks that will be invoked when
input device is opened or closed, allowing, for example, to enable
the device.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prior to this patch the code was dividing the src_v by the dst_h
and vice versa, rather than src_v/dst_v and src_h/dst_h.
This could lead to problems in the calculation of the display
watermarks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I wrote this for the prime sharing work, but I also noticed other external
non-upstream drivers from a large company carrying a similiar patch, so I
may as well ship it in master.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch addresses an issue seen on 82580 in which the MDICNFG
register will be reset during a single function reset and as a
result we will be unable to communicate with the PHY. To correct
the issue, added a call to reset_mdicnfg just prior to the first
access of the MDICNFG register in sgnii_uses_mdio.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register. The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My fine DisplayPort output was getting ST dithering forever after
having had the LVDS enabled at one point.
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not warn unnecessarily
UBI: do not print message about corruptes PEBs if we have none of them
UBI: improve delete-compatible volumes handling
UBI: fix error message and compilation warnings
UBI: generate random image_seq when formatting MTD devices
UBI: improve ECC error message
UBI: improve corrupted flash handling
UBI: introduce eraseblock counter variables
UBI: introduce a new IO return code
UBI: simplify IO error codes
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
When transitioning a QP to the error state, in progress RWQEs need to
be marked complete. This also involves releasing the reference count
to the memory regions referenced in the SGEs. The locking in the
receive packet processing wasn't sufficient to prevent qib_error_qp()
from modifying the r_sge state at the same time, thus leading to
kernel panics.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't processes too many packets without allowing other IRQ functions
a chance to run. Otherwise, there is a chance of getting a "soft
lockup" messages and poor application response times.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs. This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts. Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes up a brace warning found by the checkpatch.pl tool
Signed-off-by: Neal Buckendahl <nealb001@tbcnet.com>
Signed-off-by: Dave Jones <davej@redhat.com>
and fix the broken case if a core's frequency depends on others.
trace_power_frequency was only implemented in a rather ungeneric way
in acpi-cpufreq driver's target() function only.
-> Move the call to trace_power_frequency to
cpufreq.c:cpufreq_notify_transition() where CPUFREQ_POSTCHANGE
notifier is triggered.
This will support power frequency tracing by all cpufreq drivers
trace_power_frequency did not trace frequency changes correctly when
the userspace governor was used or when CPU cores' frequency depend
on each other.
-> Moving this into the CPUFREQ_POSTCHANGE notifier and pass the cpu
which gets switched automatically fixes this.
Robert Schoene provided some important fixes on top of my initial
quick shot version which are integrated in this patch:
- Forgot some changes in power_end trace (TP_printk/variable names)
- Variable dummy in power_end must now be cpu_id
- Use static 64 bit variable instead of unsigned int for cpu_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: davej@redhat.com
CC: arjan@infradead.org
CC: linux-kernel@vger.kernel.org
CC: robert.schoene@tu-dresden.de
Tested-by: robert.schoene@tu-dresden.de
Signed-off-by: Dave Jones <davej@redhat.com>
For UP systems this is not required, and results in a more consistent
sample interval.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jocelyn Falempe <jocelyn.falempe@motorola.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
