With a separate IP address for iSCSI, connections should proceed
whether or not we can get a route to the target from the network stack.
It is possible that the network IP address may not reach the iSCSI target.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some data structures are freed when the device is down and it will
crash if an ISCSI netlink message is received. Add RCU protection
to prevent this. In the shutdown path, ulp_ops[CNIC_ULP_L4] is
assigned NULL and rcu_synchronized before freeing the data
structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnx2 devices, always send notification to bnx2i to let it initiate
the cleanup when RST is received.
For bnx2x devices, add unsolicited RST_COMP handling to start the cleanup.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize IP ID and handle some additional connection errors.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating 128 struct netdev_queue per device, use the
minimum value between 128 and the number of possible txq's, to
reduce ram usage and "tc -s -d class shod dev .." output.
This patch fixes Eric Dumazet's patch to set the TX queues to
the correct minimum.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling TSO can cause the dev_watchdog timer to be triggered because
when TSO is disabled netif_tx_stop_all_queues is called. If the watchdog
timer fires while the queues are stopped and traffic has not recently been
sent on a paticular queue this is falsly identified as a hang and
ndo_tx_timeout() is called. This is ocossionally seen during testing.
This removes the netif_tx_stop_all_queues() it is not needed. The scheduler
submits skb's with dev_hard_start_xmit(), this checks if netif_needs_gso and
if so it calls dev_gso_segment. Disabling TSO will cause dev_hard_start_xmit()
to do the gso processing. However ixgbe does not use the features flags to
determine if it needs to use tso or not instead it uses skb->gso_size so
ixgbe will process these frames correctly regardless of the netdev features
flag.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work around 82599 HW issue when HWRSC is enabled on IOMMU enabled
kernels. 82599 HW is updating the header information after setting the
descriptor to done, resulting DMA mapping/unmapping issues on IOMMU
enabled systems. To work around the issue delay unmapping of first packet
that carries the header information until end of packet is reached.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate spinlock for tx and rx to resolve double-locking.
This is potential bug while this controller does not exist on any
SMP platforms, but lockdep or rt-preempt reveals this bug.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from net_tx(). So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger tx-ring overflow.
This fix is ported from commit 662a96bd6f
("tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON").
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hmm so actually my original patch including this bit was correct,
"list = list->next;" confused me :) - will send patch correcting that in a few.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removed some needless checks and also corrected bug in lp486e (dmi was passed
instead of dmi->dmi_addr)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the bus-error reporting configurable and allows to
retrieve the CAN TX and RX bus error counters via netlink interface.
I have added support for the SJA1000. The TX and RX bus error counters
are also copied to the data fields 6..7 of error messages when state
changes are reported.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt)
Convert logging messages to pr_<level> and netdev_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert CH_<level> and CH_DBG uses to pr_<level> and netif equivalents
Remove CH_<level> and CH_DBG macro definitions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samll cleanup in drivers/isdn/gigaset/capi.c where own implementation of
isxdigit() has been changed to kernel native one.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability of the Gigaset driver's kernel messages by
removing a few unnecessary messages and limiting the emission
of some debug messages more narrowly.
Impact: logging
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy the mechanism from ser_/usb_gigaset to avoid producing
spurious empty responses for CR/LF sequences from the device.
Add a comment in all drivers documenting that behaviour.
Correct an off by one error that might result in a one byte
buffer overflow when receiving an unexpectedly long reply.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_on() and netif_carrier_off() should be called from
link status interrupt handler
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keycodes in 248 - 254 range were reserved for special needs (scrolling)
of atkbd driver. Now that the driver has been switched to use unsigned
short keycodes instead of unsigned char we can release this range back
into pull. We keep code 255 (ATKBD_KEY_NULL) reserved since users may
have been using it to silence keys they do not care about since atkbd
silently drops scancodes mapped to this keycode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Given the right combination of ThinkPad and X.org, just reading the
video output control state is enough to hard-crash X.org.
Until the day I somehow find out a model or BIOS cut date to not
provide this feature to ThinkPads that can do video switching through
X RandR, change permissions so that only processes with CAP_SYS_ADMIN
can access any sort of video output control state.
This bug could be considered a local DoS I suppose, as it allows any
non-privledged local user to cause some versions of X.org to
hard-crash some ThinkPads.
Reported-by: Jidanni <jidanni@jidanni.org>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Studying the DSDTs of various thinkpads, it looks like bit 3 of the
argument to SBDC and SWAN is not "set radio to last state on resume".
Rather, it seems to be "if this bit is set, enable radio on resume,
otherwise disable it on resume".
So, the proper way to prepare the radios for S3 suspend is: disable
radio and clear bit 3 on the SBDC/SWAN call to to resume with radio
disabled, and enable radio and set bit 3 on the SBDC/SWAN call to
resume with the radio enabled.
Also, for persistent devices, the rfkill core does not restore state,
so we really need to get the firmware to do the right thing.
We don't sync the radio state on suspend, instead we trust the BIOS to
not do anything weird if we never touched the radio state since boot.
Time will tell if that's a wise way of doing things...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Thadeu Lima de Souza Cascardo reports this:
Brightness notification does not work until the user writes to
hotkey_mask attribute. That's because the polling thread will only run
if hotkey_user_mask is set and someone is reading the input device or
if hotkey_driver_mask is set. In this second case, this condition is
not tested after the mask is changed, because the brightness and
volume drivers are started after the hotkey drivers.
Fix tpacpi_hotkey_driver_mask_set() to call hotkey_poll_setup(), so
that the poller kthread will be started when needed.
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
The driver was not starting the NVRAM polling thread if the input
device was bound immediately after registration.
This fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=15118
Reported-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
We can stop pestering users for confirmation of the brightness_mode
default for firmware TP-76.
While at it, add a few missing comments in that quirk table.
Reported-by: Whoopie <whoopie79@gmx.net>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Event 0x3006 is used to help power management of the ODD in the
UltraBay. The EC generates this event when the ODD eject button is
pressed (even if the bay is powered down).
Normally, Linux doesn't need this as we keep the SATA link powered
up (which wastes power). The EC powers up the bay by itself when the
ODD eject button is pressed, and the SATA PHY reports the hotplug.
However, we could also power that SATA link down (and for that matter,
also power down the Ultrabay) if the ODD is left idle for a while with
no disk inside, and use event 0x3006 to know when we need that SATA link
powered back up.
For now, just stop asking for more information when event 0x3006 is
seen, there is no point in pestering users about it anymore.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
spi: Correct SPI clock frequency setting in spi_mpc8xxx
spi/spi_s3c64xx.c: Fix continuation line formats
spi/dw_spi: Fix dw_spi_mmio to depend on HAVE_CLK
spi/dw_spi: Allow dw_spi.c to be a module
spi/dw_spi: mmio code style fixups
Memory-mapped dw_spi driver
spi/dw_spi: fix missing export of dw_spi_remove_host
spi/dw_spi: conditional transfer mode changes
spi/dw_spi: remove conditional from 'poll_transfer'.
spi/dw_spi: fixed a spelling typo in a warning message.
spi/dw_spi: add return value to empty mrst_spi_debugfs_init()
spi/dw_spi: enable platform specific chipselect.
spi/dw_spi: add a FIFO depth detection
spi/dw_spi: fix __init/__devinit section mismatch
spi: xilinx_spi: Fix up I/O routine wrapping bogosity.
spi/spi_imx: add device information by switching pr_debug() to dev_dbg()
spi: update MSIOF includes
spi/dw_spi: refine the IRQ mode working flow
spi/dw_spi: add a missed dw_spi_remove_host() in exit sequence
spi/dw_spi: bug fix in wait_till_not_busy()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (41 commits)
HID: usbhid: initialize interface pointers early enough
HID: extend mask for BUTTON usage page
HID: hid-ntrig: Single touch mode tap
HID: hid-ntrig: multitouch cleanup and fix
HID: n-trig: remove unnecessary tool switching
HID: hid-ntrig add multi input quirk and clean up
HID: usbhid: introduce timeout for stuck ctrl/out URBs
HID: magicmouse: coding style and probe failure fixes
HID: remove MODULE_VERSION from new drivers
HID: fix up Kconfig entry for MagicMouse
HID: add a device driver for the Apple Magic Mouse.
HID: Export hid_register_report
HID: Support for MosArt multitouch panel
HID: add pressure support for the Stantum multitouch panel
HID: fixed bug in single-touch emulation on the stantum panel
HID: fix typo in error message
HID: add mapping for "AL Network Chat" usage
HID: use multi input quirk for TouchPack touchscreen
HID: make full-fledged hid-bus drivers properly selectable
HID: make Wacom modesetting failures non-fatal
...
Currently, only those mem resources are validated which are already
registered at the time the first PCMCIA card is inserted. As we can
only validate resources immediately after card insert, store
"registered" mem resources in mem_db, and only upon validation move
them to mem_db_valid. When allocationg mem resources, mem_db_valid is
then preferred to mem_db.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Calling the ENAB method on Toshiba laptops results in notifications being
sent when laptop hotkeys are pressed. This patch simply calls that method
and sets up an input device if it's successful.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for KR device id 0x0110. While at it, cleanup
nes_init_phy() by splitting it into nes_init_1g_phy() and
nes_init_2025_phy().
Remove support for NES_PHY_TYPE_IRIS, which was used on an XFP board
that was only manufactured in small quantities and given out for evals
in even smaller quantities.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Latitude C640 has another variation of dell in its DMI vendor entry.
Add it to the whitelist in order to enjoy the sweet fruits of software
backlight toggling.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Instead of a MODULE_DEVICE_TABLE for every acpi_driver ids table, we
create a table containing all ids to export to get a module alias for
each one.
This will fix automatic loading of the driver when one of the ACPI
devices is not present (like the accelerometer, which is not present in
some models).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Right now, we assume that the hardware rfkill switch on Dells toggles all
radio devices. In fact, this can be configured in the BIOS and so right
now we may mark a device as hardware killed even when it isn't. Add code
to query the devices controlled by the switch, and use this when
determining the hardware kill state of a radio.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Calls to communicate with system firmware via a SMI (using dcdbas)
need to use a buffer that has a physical address of 4GB or less.
Currently the dell-laptop driver does not guarantee this, and when the
buffer address is higher than 4GB, the address is truncated to 32 bits
and the SMI handler writes to the wrong memory address.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
The Mini family doesn't support smbios 17,11 although it reports it does.
Signed-off-by: Mario Limonciello <superm1@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The "hardware" switch is tied directly to a BIOS interface that will
connect and disconnect the hardware from the bus.
If you use the software interface to request the BIOS to make these
changes, the HW switch will be in an inconsistent state and LEDs may not
reflect the state of the HW.
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
