PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings. This issue is amplified when
there are multiple rings enabled. To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for Dynapro serial touchscreen, which used to be
supported in Xorg. The driver needs updated inputattach utility to
initialize serial port and create proper serio device before the
driver will be bound to it.
Signed-off-by: Tias Guns <tias@ulyssis.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the main loop to search all buffers before sleeping.
Remove dead code
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Spread spectrum is a periodic disturbance added
to the feedback divider to change the pixel clock
periodically to reduce interference.
Only enabled on LVDS.
v2: add support for r4xx and fix DCE 3
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The *_HIGH regs are reversed. The secondary ones are in the
primary block and vice versa.
We currently only use a 32 bit internal address, so these are
0 for now.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch only changes this is the swap path, where it doesn't loop.
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Reduce the chance of error and avoid a bit of overhead.
- Use switch to assign color and format
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Where supported use ulMinPixelClockPLL_Output rather than
usMinPixelClockPLL_Output for pll_out_min. This seems to
improve pll selection on some boards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem boils down to the order when the bit11
of the texture size is or'ed to the original width.
In the end each mipmap level has the same width or
height because of that 11 bit is ored to the scaled
down lod with and thus blows up the size again to the
full size or more due to the power of two rounding
afterwards.
The attached patch changes this order so that the
texture sizes are computed correct. Also the on error
the yet missing inputs to the size computation are
printed which helped me to find out where it really breaks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add SUPERH to the Kconfig dependencies for tmio_mmc.
This change allows us to drive the SDHI hardware blocks
found in SuperH Mobile with tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an MFD driver for the SuperH Mobile SDHI
hardware block. At this point the driver simply wraps the
tmio-mmc driver with some clock code. In the future this
driver is the place to put SDHI specific hotplug code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add at91sam9g45 dependency to drivers/dma/Kconfig
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As the PCMCIA core already determines the multifunction count, the
ConfigBase address and the Present value, we can use them directly
instead of parsing the CIS again. By making use of pcmcia_loop_config(),
we can further remove the remaining call to pcmcia_get_first_tuple()
and friends.
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Out of 10 PCI_IDs found in the PCMCIA subsystem, only two were not defined in
pci_ids.h. Move them and drop the duplicates. Successfully build-tested.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The CL-PD6729 chip in some docking station is not initialized properly
under Linux. In that case, do not load the pd6729 driver.
[Dominik Brodowski <linux@dominikbrodowski.net>: spelling fixes, check for NULL not 0]
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.
Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.
For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.
The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.
This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing apples to bananas doesn't seem right. Consistently use the
chips enum for chip type comparisons, to avoid such bugs in the
future.
The bug has been there since support for the IT8718F was added, so
VID never worked for this chip nor for the similar IT8720F.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SCH311x chips do not have VID inputs, so the cpu0_vid and vrm
attributes shouldn't be created for them.
This fixes lm-sensors ticket #2353:
http://www.lm-sensors.org/ticket/2353
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Udo van den Heuvel <udovdh@xs4all.nl>
Cc: Juerg Haefliger <juergh@gmail.com>
If unsigned the watchdog_trigger() return value will not be
checked correctly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP. Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration. Also, the MTD partition will currently
be left registered if netdev registration fails.
Fix both these problems by moving the MTD probe after netdev
registration. Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC and PHY probing are bound up together, as evidenced by the
initialisation of efx_nic::loopback_modes. Remove the current
arbitrary separation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the implementation a lot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes efx_pci_remove_main() more obviously the inverse of
efx_pci_probe_main(), and matches our out-of-tree driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>