before trying to enter simple mode transport method.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The end of the function is reachable both when host is and is not NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
I may have an explanation for the LSI 1068 HBA hangs provoked by ATA
pass-through commands, in particular by smartctl.
First, my version of the symptoms. On an LSI SAS1068E B3 HBA running
01.29.00.00 firmware, with SATA disks, and with smartd running, I'm seeing
occasional task, bus, and host resets, some of which lead to hard faults of
the HBA requiring a reboot. Abusively looping the smartctl command,
# while true; do smartctl -a /dev/sdb > /dev/null; done
dramatically increases the frequency of these failures to nearly one per
minute. A high IO load through the HBA while looping smartctl seems to
improve the chance of a full scsi host reset or a non-recoverable hang.
I reduced what smartctl was doing down to a simple test case which
causes the hang with a single IO when pointed at the sd interface. See
the code at the bottom of this e-mail. It uses an SG_IO ioctl to issue
a single pass-through ATA identify device command. If the buffer
userspace gives for the read data has certain alignments, the task is
issued to the HBA but the HBA fails to respond. If run against the sg
interface, neither the test code nor smartctl causes a hang.
sd and sg handle the SG_IO ioctl slightly differently. Unless you
specifically set a flag to do direct IO, sg passes a buffer of its own,
which is page-aligned, to the block layer and later copies the result
into the userspace buffer regardless of its alignment. sd, on the other
hand, always does direct IO unless the userspace buffer fails an
alignment test at block/blk-map.c line 57, in which case a page-aligned
buffer is created and used for the transfer.
The alignment test currently checks for word-alignment, the default
setup by scsi_lib.c; therefore, userspace buffers of almost any
alignment are given directly to the HBA as DMA targets. The LSI 1068
hardware doesn't seem to like at least a couple of the alignments which
cross a page boundary (see the test code below). Curiously, many
page-boundary-crossing alignments do work just fine.
So, either the hardware has an bug handling certain alignments or the
hardware has a stricter alignment requirement than the driver is
advertising. If stricter alignment is required, then in no case should
misaligned buffers from userspace be allowed through without being
bounced or at least causing an error to be returned.
It seems the mptsas driver could use blk_queue_dma_alignment() to advertise
a stricter alignment requirement. If it does, sd does the right thing and
bounces misaligned buffers (see block/blk-map.c line 57). The following
patch to 2.6.34-rc5 makes my symptoms go away. I'm sure this is the wrong
place for this code, but it gets my idea across.
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's,
and setting the cdb length for > 16 byte in the SCSI_IO->control parameter.
Signed-off-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
This converts the most common of the x86 clocksources over to use
clocksource_register_hz/khz.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-11-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use the MMC core's ability to poll for card detection. This also has
the advantage of doing the gpio_get_value from a workqueue instead of
timer, allowing the gpio to be on a sleeping gpiochip.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the data transfer size to allow multi block transfers to work.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmci driver's SG list iteration logic assumes that each SG entry
spans only one page, and only maps and flushes one page of the sg. This
is not a valid assumption. Fix it by converting the driver to the
sg_miter API, which correctly handles sgs which span multiple pages.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.
Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds nosy-dump, the userspace part of nosy, the IEEE 1394 traffic
sniffer for Texas Instruments PCILynx/ PCILynx2 based cards. Author is
Kristian Høgsberg.
The files added here are taken from
git://anongit.freedesktop.org/~krh/nosy commit ee29be97 (2009-11-10)
with the following changes by Stefan Richter:
- Parts pertaining to the kernel module removed from Makefile.
- dist target removed from the Makefile.
- Mentioned nosy-dump in the Kconfig help to nosy's kernel component.
- Add copyright notice to nosy-dump.c. This is a duplicate of the
respective notice in the kernel component nosy.c except for a time
span of 2002 - 2006, according to Kristian's git log.
"git shortlog decode-fcp.c list.h nosy-dump.[ch]" from nosy's git
repository:
Jonathan Woithe (1):
Save logs on Ctrl-C
Kristian Høgsberg (11):
Pull over nosy from mercurial repo.
Remove some fields from default view, add logging feature.
Use infinite time out for poll(), mark more detail fields.
Fix byte ordering macro.
Add decoding of iso data and lock packets.
Add flag to indicate data length field.
Add cycle start packet decoding, add --iso and --cycle-start flags.
Distinguish between phy-packets and 0-length iso data.
Fix transaction and stats view.
Add simple AV/C decoder.
Don't break down on big payloads.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Replace home-grown printk wrapper macros by ones from kernel.h and
device.h.
Also raise the log level in set_phy_reg() from debug to error because
these are really error conditions. Could even be WARN_ON. Lower the
log level in the device probe and driver shutdown from notice to info.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1.) The DMA programs (struct pcl) are PCI-endian = little endian data
(except for the 3rd quadlet in a PCL which the controller does not
touch). Annotate them as such.
Fix all accesses of the PCL to work with big endian CPUs also. Not
actually tested, I only have a little endian PC to test with. This
includes replacement of a bitfield struct pcl_status by open-coded
shift and mask operations.
2.) The two __attribute__ ((packed)) at struct pcl are not really
required since it consists of u32/__le32 only, i.e. there will be no
padding with or without the attribute.
3.) The received IEEE 1394 data are byteswapped by the controller from
IEEE 1394 endian = big endian to PCI endian = little endian because the
PCL_BIGENDIAN control bit is set. Therefore annotate the DMA buffer as
a __le32 array.
Fix the one access of the DMA buffer (the check of the transaction code
of link packets) to work with big endian CPUs. Also fix the two
accesses of the client bounce buffer (the reading of packet length).
4.) Add a comment to the userspace ABI header that all of the data gets
out as little endian data, except for the timestamp which is CPU endian.
(We could make it little endian too, but why? Vice versa, an ioctl
could be added to dump packet data in big endian byte order...)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix race between nosy_open() and remove_card() by replacing the
unprotected array of card pointers by a mutex-protected list of cards.
Make card instances reference-counted and let each client hold a
reference.
Notify clients about card removal via POLLHUP in poll()'s events
bitmap; also let read() fail with errno=ENODEV if the card was removed
and everything in the buffer was read.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
nosy_start/stop_snoop() and nosy_add/remove_client() are simple enough
to be inlined into their callers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
nosy_start/stop_snoop() are always only called by the ioctl method, i.e.
with IRQs enabled. packet_handler() and bus_reset_handler() are always
only called by the IRQ handler. Hence neither one needs to track IRQ
flags.
To underline the call context of packet_handler() and
bus_reset_handler(), rename these functions to *_irq_handler().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
nosy_stop_snoop() would blow up the second time it was called without
nosy_start_snoop() in between.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The required serialization of NOSY_IOC_START and NOSY_IOC_STOP is
already provided by the client_list_lock.
NOSY_IOC_FILTER does not really require serialization since accesses
to tcode_mask are atomic on any sane CPU architecture. Nevertheless,
make it explicit that we want this to be atomic by means of
client_list_lock (which also surrounds the other tcode_mask access in
the IRQ handler). While we are at it, change the type of tcode_mask to
u32 for consistency with the user API.
NOSY_IOC_GET_STATS does not require serialization against itself. But
there is a bug here regarding concurrent updates of the two counters
by the IRQ handler. Fix it by taking the client_list_lock in this ioctl
too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Extend copyright note to 2007, c.f. Kristian's git log.
Includes:
- replace some <asm/*.h> by <linux/*.h>
- add required indirectly included <linux/spinlock.h>
- order alphabetically
Coding style related changes:
- change to utf8
- normalize whitespace
- normalize comment style
- remove usages of __FUNCTION__
- remove an unnecessary cast from void *
Const and static declarations:
- driver_name is not const in pci_driver.name, drop const qualifier
- driver_name can be taken from KBUILD_MODNAME
- the global variable minors[] can and should be static
- constify struct file_operations instance
Data types:
- Remove unused struct member struct packet.code. struct packet is
only used for driver-internal bookkeeping; it does not appear on the
wire or in DMA programs or the userspace ABI. Hence the unused
member .code can be removed without worries.
Preprocessor macros:
- unroll a preprocessor macro that containd a return
- use list_for_each_entry
Printk:
- add missing terminating \n in some format strings
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This adds the traffic sniffer driver for Texas Instruments PCILynx/
PCILynx2 based cards. The use cases for nosy are analysis of
nonstandard protocols and as an aid in development of drivers,
applications, or firmwares.
Author of the driver is Kristian Høgsberg. Known contributers are
Jody McIntyre and Jonathan Woithe.
Nosy programs PCILynx chips to operate in promiscuous mode, which is a
feature that is not found in OHCI-1394 controllers. Hence, only special
hardware as mentioned in the Kconfig help text is suitable for nosy.
This is only the kernelspace part of nosy. There is a userspace
interface to it, called nosy-dump, proposed to be added into the tools/
subdirectory of the kernel sources in a subsequent change. Kernelspace
and userspave component of nosy communicate via a 'misc' character
device file called /dev/nosy with a simple ioctl() and read() based
protocol, as described by nosy-user.h.
The files added here are taken from
git://anongit.freedesktop.org/~krh/nosy commit ee29be97 (2009-11-10)
with the following changes by Stefan Richter:
- Kconfig and Makefile hunks are written from scratch.
- Commented out version printk in nosy.c.
- Included missing <linux/sched.h>, reported by Stephen Rothwell.
"git shortlog nosy{-user.h,.c,.h}" from nosy's git repository:
Jonathan Woithe (2):
Nosy updates for recent kernels
Fix uninitialised memory (needed for 2.6.31 kernel)
Kristian Høgsberg (5):
Pull over nosy from mercurial repo.
Use a misc device instead.
Add simple AV/C decoder.
Don't break down on big payloads.
Set parent device for misc device.
As a low-level IEEE 1394 driver, its files are placed into
drivers/firewire/ although nosy is not part of the firewire driver
stack.
I am aware of the following literature from Texas Instruments about
PCILynx programming:
SCPA020A - PCILynx 1394 to PCI Bus Interface TSB12LV21BPGF
Functional Specification
SLLA023 - Initialization and Asynchronous Programming of the
TSB12LV21A 1394 Device
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
This patch restores the ability to set msglvl through ethtool.
The issue was introduced by:
commit 675ad47375
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a xen_emul_unplug command line option to the kernel to unplug
xen emulated disks and nics.
Set the default value of xen_emul_unplug depending on whether or
not the Xen PV frontends and the Xen platform PCI driver have
been compiled for this kernel (modules or built-in are both OK).
The user can specify xen_emul_unplug=ignore to enable PV drivers on HVM
even if the host platform doesn't support unplug.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
usbnet_terminate_urbs() uses schedule_timeout() with argument 3 msecs.
schedule_timeout() uses jiffies as argument, so convert msecs to jiffies
with msecs_to_jiffies().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
