Commit graph

93,853 commits

Author SHA1 Message Date
Eilon Greenstein
279abdf59c bnx2x: Stop management traffic in loopback test
Since management traffic cannot go on the wire while configured to loopback,
simply stop it to avoid race condition when the MAC is set to loopback in the
middle of a packet

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21 11:18:26 -07:00
Luis R. Rodriguez
c66284f2a4 ath9k: Tune ANI function processing on AP mode during ANI reset
For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.

Testedy-by: Steven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:43 -04:00
Andy Whitcroft
7adfd5c716 rt2x00: Fix chipset detection for rt2500usb
The commit below changed the semantics of rt2x00_check_rev so that it no
longer checked the bottom 4 bits of the rev were non-zero.  During that
conversion this part of the check was not propogated to the rt2500usb
initialisation.

    commit 358623c22c
    Author: Ivo van Doorn <ivdoorn@gmail.com>
    Date:   Tue May 5 19:46:08 2009 +0200

        rt2x00: Simplify rt2x00_check_rev

Without this check rt73 devices are miss recognised as rt2500 devices and
two drivers are loaded.  Preventing the device being used.  Reinstate this
check.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:43 -04:00
Larry Finger
3da7429ce9 rtl8187: Fix for kernel oops when unloading with LEDs enabled
When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel
may oops when the module is unloaded as the workqueue for led_on was
not being cancelled.

This patch fixes the problem reported in
http://marc.info/?l=linux-wireless&m=124742957615781&w=2.

Reported-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:42 -04:00
Bob Copeland
65b5a69860 ath5k: temporarily disable crypto for AP mode
Pavel Roskin reported some issues with using AP mode without
nohwcrypt=1.  Most likely this is similar to the problem fixed
some time ago in ath9k by 3f53dd64f1,
"ath9k: Fix hw crypto configuration for TKIP in AP mode."

That only affects TKIP but it's easiest to just disable that and
WEP too until we get a proper fix in.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:42 -04:00
Johannes Berg
e603d9d824 mac80211_hwsim: fix use after free
Once the "data" pointer is freed, we can't be iterating
to the next item in the list any more so we need to use
list_for_each_entry_safe with a temporary variable.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:40 -04:00
Johannes Berg
5d41635195 mac80211_hwsim: fix unregistration
If you rmmod the module while associated, frames might
be transmitted during unregistration -- which will crash
if the hwsim%d interface is unregistered first, so only
do that after all the virtual wiphys are gone.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:39 -04:00
Reinette Chatre
7b80ece41a iwlwifi: only update byte count table during aggregation
The byte count table is only used for aggregation. Updating it
in other cases caused fragmented frames to be dropped.

This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:33 -04:00
Reinette Chatre
872ed1902f iwlwifi: only show active power level via sysfs
This changes the power_level file to adhere to the "one value
per file" sysfs rule. The user will know which power level was
requested as it will be the number just written to this file. It
is thus not necessary to create a new sysfs file for this value.

In addition it fixes a problem where powertop's parsing expects
this value to be the first value in this file without any descriptions.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:31 -04:00
Zhu Yi
513a2396d8 iwmc3200wifi: fix NULL pointer dereference in iwm_if_free
The driver private data is now based on wiphy. So we should not
touch the private data after wiphy_free() is called. The patch
fixes the potential NULL pointer dereference by making the
iwm_wdev_free() the last one on the interface removal path.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21 12:07:31 -04:00
Paul Mundt
fc6cca3917 Merge branches 'sh/compressors' and 'sh/stable-updates' 2009-07-21 17:37:18 +09:00
Dmitry Torokhov
24d01c0681 Input: sh_keysc - allow modifying keymap from userspace
Adjust the driver so EVIOCGKEYCODE/EVIOCSKEYCODE work.

Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-07-21 01:14:13 -07:00
Marek Vasut
99fde513f5 Input: wm97xx - add possibility to control the GPIO_STATUS shift
This patch allows tweaking the behaviour of GPIO_STATUS register
shift quirk that's in wm97xx-core. The problem with GPIO_STATUS
register being shifted by one doesn't appear on all hardware it
seems and causes problems with accelerated touchscreen drivers on
Palm hardware. Therefore an accelerated touchscreen driver can select
if the shift is/isn't happening on the hardware.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-07-20 22:30:33 -07:00
Marek Vasut
b833306feb Input: wm97xx - add Palm support to Mainstone accelerated touch
This patch refactors the Mainstone accelerated touch code a little and
adds support for interrupt driven touchscreen on Palm LifeDrive, TX and
Tungsten T5.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-07-20 22:30:23 -07:00
Jerone Young
032e46cbf5 Input: atkbd - add force relese key quirk for Soltech TA12
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.

Added quirk data for forced release keys.

BugLink: https://bugs.launchpad.net//bugs/397499

Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-07-20 22:29:51 -07:00
Nicolas Pitre
6cdbf73449 mvsdio: fix handling of partial word at the end of PIO transfer
Standard data flow for MMC/SD/SDIO cards requires that the mvsdio
controller be set for big endian operation.  This is causing problems
with buffers which length is not a multiple of 4 bytes as the last
partial word doesn't get shifted all the way and stored properly in
memory.  Let's compensate for this.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-20 16:46:34 -07:00
Alan Cox
23198fda71 tty: fix chars_in_buffers
This function does not have an error return and returning an error is
instead interpreted as having a lot of pending bytes.

Reported by Jeff Harris who provided a list of some of the remaining
offenders.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-20 16:38:43 -07:00
Julia Lawall
254702568d specialix.c: convert nested spin_lock_irqsave to spin_lock
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call.  Indeed, the second call does not
need to save the interrupt state, so it is changed to a simple
spin_lock.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression lock1,lock2;
expression flags;
@@

*spin_lock_irqsave(lock1,flags)
... when != flags
*spin_lock_irqsave(lock2,flags)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-20 16:38:43 -07:00
Kay Sievers
c46a7aec55 vc: create vcs(a) devices for consoles
The buffer for the consoles are unconditionally allocated at con_init()
time, which miss the creation of the vcs(a) devices.

Since 2.6.30 (commit 4995f8ef9d, 'vcs:
hook sysfs devices into object lifetime instead of "binding"' to be
exact) these devices are no longer created at open() and removed on
close(), but controlled by the lifetime of the buffers.

Reported-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Tested-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Cc: stable@kernel.org
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-20 16:38:43 -07:00
Wolfgang Grandegger
1b0d92244f can: switch carrier on if device was stopped while in bus-off state
This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.

Signed-off-by: Kurt Van Dijck <kurt.van.dijck@skynet.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 12:28:30 -07:00
Wolfgang Grandegger
b3d0df7ca3 can: restart device even if dev_alloc_skb() fails
If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.

Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 12:28:29 -07:00
Wolfgang Grandegger
e2372902d8 can: sja1000: remove duplicated includes
Remove duplicated #include('s) in
  drivers/net/can/sja1000/sja1000.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 12:28:26 -07:00
Cesar Eduardo Barros
90cb665937 New device ID for sc92031 [1088:2031]
rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)

Cc: rain_maker@root-forum.org
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:27:02 -07:00
Ken Kawasaki
e445bb4ed6 3c589_cs: re-initialize the multicast in the tc589_reset
3c589_cs:
re-initialize the multicast in the tc589_reset,
and spin_lock the set_multicast_list function.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:26:55 -07:00
Dhananjay Phadke
e4135c2da1 netxen: fix thermal check and shutdown
Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.

Old code was only monitoring temperature for function 0 only.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:23:33 -07:00
Dhananjay Phadke
b2af9cb06d netxen: fix deadlock on dev close
netxen: fix deadlock on dev close

The tx ring accounting fix in commit cb2107be43
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.

This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:23:31 -07:00
Dhananjay Phadke
cf981ffb31 netxen: fix context deletion sequence
o Use D3 reset context deletion for NX2031, it cleans up
  more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
  commands are sent on tx context, so it should be the last
  to go.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:23:28 -07:00
Ben Dooks
3ba81f3ece net: Micrel KS8851 SPI network driver
Network driver for the SPI version of the Micrel KS8851
network chip.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:23:26 -07:00
roel kluin
27e0955184 b44: strncpy does not null terminate string
strlcpy() will always null terminate the string. Also use the
sizeof(version) to strlcopy() the version string.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:02:58 -07:00
Wan ZongShun
a50a97d415 Add mac driver for w90p910
Add mac driver support for evaluation board based on w90p910.

Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 07:45:05 -07:00
Robert Richter
1b294f5960 oprofile: Adding switch counter to oprofile statistic variables
This patch moves the multiplexing switch counter from x86 code to
common oprofile statistic variables. Now the value will be available
and usable for all architectures. The initialization and
incrementation also moved to common code.

Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:43:21 +02:00
Robert Richter
a5659d17ad oprofile: Grouping multiplexing code in oprof.c
This patch moves multiplexing code to a single section of code. This
reduces the use of #ifdefs especially within functions.

Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:43:19 +02:00
Robert Richter
16422a6e2d oprofile: Remove oprofile_multiplexing_init()
oprofile_multiplexing_init() can be removed when moving the
initialization of oprofile_time_slice to oprofile_create_files().

Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:43:19 +02:00
Robert Richter
afe1b50fe6 oprofile: Rename variable timeout_jiffies and move to oprofile_files.c
This patch renames timeout_jiffies into an oprofile specific name. The
macro MULTIPLEXING_TIMER_DEFAULT is changed too.

Also, since this variable is controlled using oprofilefs, its
definition is moved to oprofile_files.c.

Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:43:19 +02:00
Robert Richter
2051cade7c oprofile: oprofile_set_timeout(), return with error for invalid args
Return with -EINVAL for invalid parameters instead of setting the
default value in oprofile_set_timeout().

Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:43:18 +02:00
Jason Yeh
4d4036e0e7 oprofile: Implement performance counter multiplexing
The number of hardware counters is limited. The multiplexing feature
enables OProfile to gather more events than counters are provided by
the hardware. This is realized by switching between events at an user
specified time interval.

A new file (/dev/oprofile/time_slice) is added for the user to specify
the timer interval in ms. If the number of events to profile is higher
than the number of hardware counters available, the patch will
schedule a work queue that switches the event counter and re-writes
the different sets of values into it. The switching mechanism needs to
be implemented for each architecture to support multiplexing. This
patch only implements AMD CPU support, but multiplexing can be easily
extended for other models and architectures.

There are follow-on patches that rework parts of this patch.

Signed-off-by: Jason Yeh <jason.yeh@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
2009-07-20 16:33:53 +02:00
Dan Carpenter
86f4d0123b intel-iommu: double kfree()
g_iommus is freed after we "goto error;".

Found by smatch (http://repo.or.cz/w/smatch.git).

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-07-20 05:01:20 +01:00
Julia Lawall
76c317d6e5 HID: Move dereferences below a NULL test
If the NULL test is necessary, then the dereferences should be moved below
the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E=E1
      when != i
  if (E == NULL||...) S
+ i = E->fld;
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-07-20 00:03:35 +02:00
Paul Mundt
c358fc46ef Merge branches 'sh/hwblk' and 'sh/platform-updates' 2009-07-20 04:28:11 +09:00
Magnus Damm
719a72b7c7 usb: r8a66597-hcd platform data on_chip support
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.

This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.

It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-20 04:27:10 +09:00
Magnus Damm
ae1cef6ea1 usb: convert r8a66597-hcd to dev_pm_ops
Convert the r8a66597-hcd driver to dev_pm_ops. This makes
the driver a good PM citizen and removes a warning printout.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-20 04:27:06 +09:00
Akinobu Mita
57594742a2 x86: Introduce set_desc_base() and set_desc_limit()
Rename set_base()/set_limit to set_desc_base()/set_desc_limit()
and rewrite them in C. These are naturally introduced by the
idea of get_desc_base()/get_desc_limit().

The conversion actually found the bug in apm_32.c:
bad_bios_desc is written at run-time, but it is defined const
variable.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
LKML-Reference: <20090718151105.GC11294@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-19 18:27:52 +02:00
Rakib Mullick
4fbfff7607 virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch
The variable virtio_blk references the function virtblk_probe() (which
is in .devinit section) and also references the function
virtblk_remove() ( which is in .devexit section). So, virtio_blk
simultaneously refers .devinit and .devexit section. To avoid this
messup, we mark virtio_blk as __refdata.

We were warned by the following warning:

  LD      drivers/block/built-in.o
  WARNING: drivers/block/built-in.o(.data+0xc8dc): Section mismatch in
  reference from the variable virtio_blk to the function
  .devinit.text:virtblk_probe()
  The variable virtio_blk references
  the function __devinit virtblk_probe()
  If the reference is valid then annotate the
  variable with __init* or __refdata (see linux/init.h) or name the variable:
  *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

  WARNING: drivers/block/built-in.o(.data+0xc8e0): Section mismatch in
  reference from the variable virtio_blk to the function
  .devexit.text:virtblk_remove()
  The variable virtio_blk references
  the function __devexit virtblk_remove()
  If the reference is valid then annotate the
  variable with __exit* (see linux/init.h) or name the variable:
  *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2009-07-19 10:46:48 +09:00
Linus Torvalds
a7571a5c88 Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Realview & Versatile: Fix i2c_board_info definitions
  [ARM] 5608/1: Updated U300 defconfig
  [ARM] 5606/1: Fix ep93xx watchdog driver headers
  [ARM] 5594/1: Correct U300 VIC init PM setting
  [ARM] 5595/1: ep93xx: missing header in dma-m2p.c
  [ARM] Kirkwood: Correct header define
  [ARM] pxa: fix ULPI_{DIR,NXT,STP} MFP defines
  backlight: fix pwm_bl.c to notify platform code when suspending
  [ARM] pxa: use kzalloc() in pxa_init_gpio_chip()
  [ARM] pxa: correct I2CPWR clock for pxa3xx
  pxamci: correct DMA flow control
  ARM: add support for the EET board, based on the i.MX31 pcm037 module
  pcm037: add MT9T031 camera support
  Armadillo 500 add NAND flash device support (resend).
  ARM MXC: Armadillo 500 add NOR flash device support (resend).
  mx31: remove duplicated #include
2009-07-18 11:59:33 -07:00
Ben Dooks
bff78650a2 ARM: HWMON: S3C24XX series ADC driver
Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-18 10:15:54 +01:00
Linus Torvalds
78af08d90b Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: Move a dereference below a NULL test
  fb/intelfb: conflict with DRM_I915 and hide by default
  drm/ttm: fix misplaced parentheses
  drm/via: Fix vblank IRQ on VIA hardware.
  drm: drm_gem, check kzalloc retval
  drm: drm_debugfs, check kmalloc retval
  drm/radeon: add some missing pci ids
2009-07-17 21:19:50 -07:00
David S. Miller
14d87e6c39 sparc: Fix cleanup crash in bbc_envctrl_cleanup()
If kthread_run() fails or never gets to run we'll have NULL
or a pointer encoded error in kenvctrld_task, rather than
a legitimate task pointer.

So this makes bbc_envctrl_cleanup() crash as it passed this
bogus pointer into kthread_stop().

Reported-by: BERTRAND Joël <joel.bertrand@systella.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-17 10:28:19 -07:00
Mike Frysinger
0741241c6b connector: make callback argument type explicit
The connector documentation states that the argument to the callback
function is always a pointer to a struct cn_msg, but rather than encode it
in the API itself, it uses a void pointer everywhere.  This doesn't make
much sense to encode the pointer in documentation as it prevents proper C
type checking from occurring and can easily allow people to use the wrong
pointer type.  So convert the argument type to an explicit struct cn_msg
pointer.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-17 10:13:21 -07:00
Sridhar Samudrala
e36aa25a53 tun: Allow tap device to send/receive UFO packets.
- Allow setting UFO on tap device and handle UFO packets.

Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>

---------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-17 10:11:00 -07:00
Sridhar Samudrala
5c5167515d virtio-net: Allow UFO feature to be set and advertised.
- Allow setting UFO on virtio-net and advertise to host.

Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-17 10:10:58 -07:00