Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.
The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);
dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"
strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must free priv->eeprom allocated in adm8211_read_eeprom().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This test is off by one because strlen() doesn't include the NULL
terminator.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.
This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the main loop in acpi_ev_initialize_gpe_block() by
rearranging code and removing the "enabled" label that is not
necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make acpi_gpe_wakeup() return error code for GPEs whose
ACPI_GPE_CAN_WAKE flag is not set. This way acpi_gpe_wakeup() will
only wake for the GPEs reported by the host OS as "wakeup" ones with
the help of acpi_gpe_can_wake().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, during initialization ACPICA walks the entire ACPI
namespace in search of any device objects with assciated _PRW
methods. All of the _PRW methods found are executed in the process
to extract the GPE information returned by them, so that the GPEs in
question can be marked as "able to wakeup" (more precisely, the
ACPI_GPE_CAN_WAKE flag is set for them). The only purpose of this
exercise is to avoid enabling the CAN_WAKE GPEs automatically, even
if there are _Lxx/_Exx methods associated with them. However, it is
both costly and unnecessary, because the host OS has to execute the
_PRW methods anyway to check which devices can wake up the system
from sleep states. Moreover, it then uses full information
returned by _PRW, including the GPE information, so it can take care
of disabling the GPEs if necessary.
Remove the code that walks the namespace and executes _PRW from
ACPICA and modify comments to reflect that change. Make
acpi_bus_set_run_wake_flags() disable GPEs for wakeup devices
so that they don't cause spurious wakeup events to be signaled.
This not only reduces the complexity of the ACPICA initialization
code, but in some cases it should reduce the kernel boot time as
well.
Unfortunately, for this purpose we need a new ACPICA function,
acpi_gpe_can_wake(), to be called by the host OS in order to disable
the GPEs that can wake up the system and were previously enabled by
acpi_ev_initialize_gpe_block() or acpi_ev_update_gpes() (such a GPE
should be disabled only once, because the initialization code enables
it only once, but it may be pointed to by _PRW for multiple devices
and that's why the additional function is necessary).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When we check if a GPE can be used for runtime signaling, we only
search the FADT GPE blocks, which is incorrect, becuase the GPE
may be located elsewhere. We really should be using the GPE device
information previously returned by _PRW here, so make that happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The commit 5d554a7bb0 (ACPI: processor: add internal
processor_physically_present()) is broken on uniprocessor (UP)
configurations, as acpi_get_cpuid() will always return -1.
We use the value of num_possible_cpus() to tell us whether we got
an invalid cpuid from acpi_get_cpuid() in the SMP case, or if
instead, we are UP, in which case num_possible_cpus() is #defined
as 1.
We use num_possible_cpus() instead of num_online_cpus() to
protect ourselves against the scenario of CPU hotplug, and we've
taken down all the CPUs except one.
Thanks to Jan Pogadl for initial report and analysis and Chen
Gong for review.
https://bugzilla.kernel.org/show_bug.cgi?id=16357
Reported-by: Jan Pogadl <pogadl.jan@googlemail.com>:
Reviewed-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hmmm. There are still people who have their editor setup with tabwidth 4.
Some of the entries were added with tabwidth 4, and for these people
the lineup looks OK. But in the Linux kernel source we use tabwidth 8.
This patch repairs that whitespace so that the number align properly.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As our device may be hot-unplugged and framebuffer cannot handle
this case by itself we need to keep track of usage count so as
to release fb_info and framebuffer memory only after the last user
has closed framebuffer.
We need to do the freeing in a scheduled work as fb_release()
is called with fb_info lock held.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reallocating memory in depth change does not work well if some
userspace application has mmapped() the framebuffer as that mapping
does not get adjusted (thus application continues to write to old
buffer).
In addition doing deferred_io_cleanup() and init() inside of set_par()
tends to deadlock with fbcon's flashing cursor.
Avoid all this by allocating a buffer that can hold 8bpp framebuffer
and just use 1/8 of it while running at 1bpp.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a minimal palette so fbcon does not try to dereference
a NULL point when fb is set to 8bpp.
fbcon stores pixels the other way around in bytes for 1bpp
than intially implemented, correct this.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not call free_irq() if request_irq() failed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() is called both in net_close() and cleanup_card(). Since it
is requested in at1700_probe1(), leave free_irq() only in cleanup_card()
for balance.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few registers have side effects on reads, eg FIFO pointers that
auto advance or mailboxes which change ownership when read. They are
unsafe to read so exclude them from ethtool register dumps.
Bump ethtool_regs.version to indicate the changed register set.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge error.
See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_rxnfc, get_rxfh_indir, and set_rxfh_indir ethtool
methods for user manipulation of the RSS table. Besides the methods
themselves the rest of the changes here store, initialize, and write
the table contents.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two copies of some resource freeing code, turn it into
a function and call it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to settle on the kind of interrupts we'll be using, a choice that
also impacts the number of queues, before registering and making visible
the net_devices. Move the relevant code up a bit.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.112.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following checkpatch errors:
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
^
ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
^
ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);
ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 52cdf8526f,
entitled "tg3: Prevent a PCIe tx glitch". The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it. The proper place for this code is within the
device's bootcode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is coded to refuse to attach to 5717 serdes devices. Now that the
hardware is better supported, we can relax this restriction. This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets. This patch adds the missing support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case. This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 2601d8a004. A
spectacular set of coincidences made it look as though the table was
setup incorrectly. The original version was correct.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The X and Y values have two more significant bits in the same byte
that contains click status. Include these in the reported value.
Thanks to Iain Hibbert of NetBSD for pointing this out.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The evdev multitouch protocol requires that a last MT sync event must be
sent after all touches are up. This change adds the last MT sync event
to the hid-magicmouse driver.
Also, don't send events when a touch leaves.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adjust ordering if framebuffer (un)registration and defio init/cleanup
to match the correct order (init defio, register FB ... unregister FB,
cleanup defio)
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.
Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a partial revert of 421f91d21a
("fix typos concerning "initiali[zs]e"") for ov511 driver, as it is
going to be completely removed in the next release anyway.
Fixes conflict in linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/mips: Fix error return codes from Sibyte i2c bus driver
i2c: Fix probability check
The VENDOR_IDs were mostly in alphabetical order, but some of the
newer entries were not added as such. Some entries were added just
at the end, some were added in the middle.
This patch places the entries once again in a properly sorted
order.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
