Commit graph

93,853 commits

Author SHA1 Message Date
Tomas Winkler
c15ff61045 iwlwifi: drop iwl3945_tid_data
This patch is one of the incremental steps for unifying iwl_station_entry
for all HWs, i.e. removing of iwl3945_station_entry
This patch drops iwl3945_tid_data and use iwl_tid_data instead.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:26 -04:00
Tomas Winkler
bed420d9c0 iwlwifi: drop struct iwl3945_hw_key
This patch replaces struct iwl3945_hw_key by struct iwl_hw_key.
It's not used directly with any host command therefore removal is trivial

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:26 -04:00
Stefano Brivio
44710bbc07 b43legacy: Remove unnecessary MMIO in interrupt hotpath
This removes unnecessary MMIO accesses in the interrupt hotpath. The
patch by Michael Buesch for b43 has been ported to b43legacy.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:26 -04:00
Vasanthakumar Thiagarajan
6b96f93e96 ath9k: cleanup beacon parameters configuration
This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:26 -04:00
Vasanthakumar Thiagarajan
d31e20af9f ath9k: Remove unused parameters which are passed to ath_beacon_config_X()
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:25 -04:00
Vasanthakumar Thiagarajan
6b45784fbe ath9k: Print hw reset failure status as signed int
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:25 -04:00
Jouni Malinen
cc65965cbb ath9k: Fix PS mode operation to receive buffered broadcast/multicast frames
The previous implementation was moving back to NETWORK SLEEP state
immediately after receiving a Beacon frame. This means that we are
unlikely to receive all the buffered broadcast/multicast frames that
would be sent after DTIM Beacon frames. Fix this by parsing the Beacon
frame and remaining awake, if needed, to receive the buffered
broadcast/multicast frames. The last buffered frame will trigger the
move back into NETWORK SLEEP state.

If the last broadcast/multicast frame is not received properly (or if
the AP fails to send it), the next Beacon frame will work as a backup
trigger for returning into NETWORK SLEEP.

A new debug type, PS (debug=0x800 module parameter), is added to make
it easier to debug potential power save issues in the
future. Currently, this is only used for the Beacon frame and buffered
broadcast/multicast receiving.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:24 -04:00
Jouni Malinen
9d64a3cfaf ath9k: Clean up RX processing a bit
This makes use of the local fc variable in bit more places and uses a
common helper macro. The part of RX process that delivers skb's to
mac80211 is moved to a separate function in preparation for future
changes that will need to do this from two places. The modifications
here should not result in any functional changes.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:24 -04:00
Jouni Malinen
d8959fbfba ath9k: Fix a check for multicast address for virtual wiphy
The broadcast bit is in the first, not the last octet..

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:24 -04:00
Gábor Stefanik
13bdcd90bb zd1211rw: Replace ZD_CS_MULTICAST with ZD_CS_NO_ACK
According to my tests, all that ZD_CS_MULTICAST does is to
disable retrying/waiting for an ACK. Reflect this by renaming
the bit to ZD_CS_NO_ACK and setting it based on
IEEE80211_TX_CTL_NO_ACK, instead of is_multicast_ether_addr.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:24 -04:00
Luis R. Rodriguez
689da1b3b8 wireless: rename IEEE80211_CHAN_NO_FAT_* to HT40-/+
This is more consistent with our nl80211 naming convention
for HT40-/+.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:22 -04:00
Luis R. Rodriguez
038659e7c6 cfg80211: Process regulatory max bandwidth checks for HT40
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.

We end up dealing with HT40 by having two passes for each channel.

The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.

The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:

 o exist
 o are enabled
 o regulatory allows 40 MHz bandwidth on its frequency range

This work allows allows us to idependently check for HT40- and
HT40+.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:46:22 -04:00
Michel Dänzer
9b6fe313bf drm: Copy back ioctl data to userspace regardless of return code.
Fixes a regression from commit 9d5b3ffc42
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-05-20 11:41:41 -07:00
Roel Kluin
a6c6733978 wireless: beyond ARRAY_SIZE of intf->crypto_stats
Do not go beyond ARRAY_SIZE of intf->crypto_stats

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:55 -04:00
Jay Sternberg
c9d2fbf36d iwlwifi: update 5000 ucode support to version 2 of API
enable iwl driver to support 5000 ucode having version 2 of API

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:55 -04:00
John W. Linville
267d493b32 airo: fix airo_get_encode{,ext} buffer overflow like I mean it...
"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment.  Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:54 -04:00
Fabio Rossi
875690c378 ath5k: fix interpolation with equal power levels
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.

Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:53 -04:00
Reinette Chatre
fbc9f97bbf iwlwifi: do not cancel delayed work inside spin_lock_irqsave
Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.

As explained by Johannes Berg <johannes@sipsolutions.net>

A - lock
T - timer

phase                   CPU 1           CPU 2
---------------------------------------------

some place that calls
cancel_timer_sync()
(which is the | code)
                                        lock-irq(A)
|                                       "lock-irq"(T)
|                                       "unlock"(T)
|                                       wait(T)
                                        unlock(A)

timer softirq
                        "lock"(T)
                        run(T)
                        "unlock"(T)

irq handler
          lock(A)
          unlock(A)

Now all that again, interleaved, leading to deadlock:

                                        lock-irq(A)
                        "lock"(T)
                         run(T)
IRQ during or maybe
before run(T) -->        lock(A)
                                        "lock-irq"(T)
                                        wait(T)

We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.

Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .

Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:53 -04:00
Forrest Zhang
a54be5d43a ath5k: fix exp off-by-one when computing OFDM delta slope
Commit e8f055f0c3 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.

get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set.  Instead, use
ilog2 which is what this code is really calculating.  Also check
coef_scaled to handle the (invalid) case where we need log2(0).

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:07:51 -04:00
Pavel Roskin
2b611cb6ee ath5k: fix scanning in AR2424
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:07:50 -04:00
Eric Lammerts
0003b795c3 fix oops when using console=ttymxcN with N > 0
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-20 19:09:20 +02:00
Linus Torvalds
6c2445efb8 Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cdrom: beyond ARRAY_SIZE of viocd_diskinfo
  xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
  xen/blkfront: allow xenbus state transition to Closing->Closed  when not Connected
2009-05-20 08:56:10 -07:00
Stephane Chatty
57fd637ad9 HID: Multitouch support for the N-Trig touchscreen
Adds support for multitouch interaction on the N-Trig touchscreen, using the
new ABS_MT_* input constants. Single touch support works as previously. This
code was tested against two versions of the N- Trig firmware: one that supports
dual pen/finger single touch, and one that supports finger multitouch but no
pen at all. Copyright notices that looked wrong were removed, as it seems that
there is only code written in 2009 by Rafin Rubin and Stephane Chatty in this
file.

Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-05-20 15:49:35 +02:00
Stephane Chatty
89f536ccfa HID: add new multitouch and digitizer contants
Added constants to hid.h for all digitizer usages (including the new multitouch
ones that are not yet in the official USB spec but are being pushed by Microsft
as described in their paper "Digitizer Drivers for Windows Touch and Pen-Based
Computers"). Updated hid-debug.c to support the new MT input constants such as
ABS_MT_POSITION_X.

Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-05-20 15:48:35 +02:00
Roel Kluin
d3375ea721 cdrom: beyond ARRAY_SIZE of viocd_diskinfo
Do not go beyond ARRAY_SIZE of viocd_diskinfo

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-20 08:42:06 +02:00
Paul Mundt
62669e61a5 sh: mach-hp6xx: Fix up the hp6xx build for hd64461 changes.
Fixes several compile errors due to the recent hd64461 I/O base changes.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-05-20 11:27:13 +09:00
Daniel Mack
10494dce0b Input: add driver for EETI touchpanels
This patch adds a driver for EETI's I2C connected touchscreens.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-05-19 19:25:35 -07:00
Michael Roth
b58895f8b1 Input: ads7846 - more detailed model name in sysfs
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-05-19 19:25:27 -07:00
Michael Roth
86579a4ccc Input: ads7846 - support swapping x and y axes
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-05-19 19:24:54 -07:00
Ville Syrjala
225c9886b9 Input: ati_remote2 - use non-atomic bitops
No point in using atomic bitops when setting the input device keybits.

Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-05-19 19:24:42 -07:00
Linus Torvalds
a71d6e0d6f Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: pcf50633: fix unsafe disable_irq()
  mfd: Keep a cache of WM8350 volatile values
2009-05-19 18:44:09 -07:00
Linus Torvalds
fbb5ba9276 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv4: make default for INET_LRO consistent with help text
  net: fix skb_seq_read returning wrong offset/length for page frag data
  pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
  be2net: add two new pci device ids to pci device table
  sch_teql: should not dereference skb after ndo_start_xmit()
  tcp: fix MSG_PEEK race check
  Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
  Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
  mv643xx_eth: fix PPC DMA breakage
  bonding: fix link down handling in 802.3ad mode
  bridge: fix initial packet flood if !STP
  bridge: relay bridge multicast pkgs if !STP
  NET: Meth: Fix unsafe mix of irq and non-irq spinlocks.
  mlx4_en: Fix not deleted napi structures
  ipconfig: handle case of delayed DHCP server
  netpoll: don't dereference NULL dev from np
  wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws
2009-05-19 18:43:50 -07:00
Ben Hutchings
97bc54152e sfc: Remove lro module parameter
GRO/LRO can be controlled through ethtool so this is unnecessary.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 16:19:08 -07:00
Brice Goglin
e5488ce569 myri10ge: update version to 1.5.0-1.415
Update myri10ge driver version to 1.5.0-1.415.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:16 -07:00
Brice Goglin
3a0c7d2d2b myri10ge: allow LRO to be enabled via ethtool
Allow myri10ge LRO to be enabled/disabled via ethtool
(and by the stack for packet forwarding).

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:15 -07:00
Jesse Brandeburg
0cefafadbb ixgbe: Cleanup feature setup code to make the code more readable
This is purely a cleanup patch.  This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:14 -07:00
Peter P Waskiewicz Jr
537d58a00a ixgbe: Change Direct Attach Twinax cable detection for SFP+ NICs
The SFF specification for Direct Attach cable detection has now been
ratified.  Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM.  The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM.  This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:14 -07:00
Peter P Waskiewicz Jr
aa5aec8885 ixgbe: Add semaphore access for PHY initialization for 82599
The SFP+ NIC (device id 0x10fb) needs a semaphore to serialize
PHY access, so our PHY init code must honor that same semaphore.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:13 -07:00
Benjamin Herrenschmidt
b674137755 drm: Round size of SHM maps to PAGE_SIZE
Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.

The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.

This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-05-19 15:35:33 -07:00
Eric Paris
fbaa58696c TPM: get_event_name stack corruption
get_event_name uses sprintf to fill a buffer declared on the stack.  It fills
the buffer 2 bytes at a time.  What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes.  2 bytes for the data and
then it nul terminates the string.  Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters.  The fix is to leave room in buf for the nul terminator.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
2009-05-20 08:30:05 +10:00
Rafael J. Wysocki
b3bad72e49 PCI PM: Fix initialization and kexec breakage for some devices
Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization.  The failure
scenario in the kexec case is the following:

* Assume a PCI device is not power-manageable by the platform and has
  PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
  PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
  device is not power-manageable by the platform, it causes
  pci_update_current_state(dev, PCI_D0) to be called.  As a result
  the device's current_state field is updated to PCI_D3, in
  accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
  state to D0.  *However*, it should also call pci_restore_bars() to
  reinitialize the device, but it doesn't, because the device's
  current_state field has been modified earlier.

To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform.  Instead, this field should be updated directly for devices
that don't support the native PCI PM.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-05-19 15:26:07 -07:00
françois romieu
3577aa1bd7 r8169: allow true forced mode setting
Due to mostly historic reasons, including a lack of reliability
of the link handling (especially with the older 8169), the
current r8169 driver emulates forced mode setting by limiting
the advertised modes.

With this change the driver allows real 10/100 forced mode
settings on the 8169 and 8101/8102.

Original idea by Vincent Steenhoute. The RTL_GIGA_MAC_VER_03
tweak was extracted from Realtek's r8169 v6.010.00 driver.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 14:31:28 -07:00
françois romieu
381f05172b r8169: remove useless struct member
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 14:31:27 -07:00
Eric Dumazet
8b2d850db2 ppp: unset IFF_XMIT_DST_RELEASE in ppp_setup()
Jarek pointed pppoe can call back dev_queue_xmit(), and might need
skb->dst, so its safer to unset IFF_XMIT_DST_RELEASE on ppp devices.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 14:24:37 -07:00
Nelson Castillo
f43ab90100 mfd: pcf50633: fix unsafe disable_irq()
Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:

: commit 3aa551c9b4
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date:   Mon Mar 23 18:28:15 2009 +0100
:
:    genirq: add threaded interrupt handler support
:
:    Add support for threaded interrupt handlers

Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-05-19 22:22:28 +02:00
Mark Brown
b126d11348 mfd: Keep a cache of WM8350 volatile values
Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.

To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-05-19 22:22:28 +02:00
Linus Torvalds
467999f50c Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: da903x: add missing __devexit_p()
2009-05-19 11:31:24 -07:00
Linus Torvalds
26a9a41823 Avoid ICE in get_random_int() with gcc-3.4.5
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):

    drivers/char/random.c: In function `get_random_int':
    drivers/char/random.c:1672: error: unrecognizable insn:
    (insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
            (subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
                        (subreg:DI (reg:SI 6 bp) 0))
                    (const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
        (nil))
    drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083

and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.

This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.

So just drop it, and mumble some incoherent curses at the compiler.

Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-19 11:25:35 -07:00
Boaz Harrosh
ac36552a52 scsi_lib: remove unused variable
The last request completion cleanup in scsi_lib left an unused
this_count variable in scsi_io_completion().
(It was used before in a code segment that now uses blk_end_request_all())

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 19:54:09 +02:00
Jesse Barnes
8e7d2b2c6e drm/i915: allocate large pointer arrays with vmalloc
For awhile now, many of the GEM code paths have allocated page or
object arrays with the slab allocator.  This is nice and fast, but
won't work well if memory is fragmented, since the slab allocator works
with physically contiguous memory (i.e. order > 2 allocations are
likely to fail fairly early after booting and doing some work).

This patch works around the issue by falling back to vmalloc for
>PAGE_SIZE allocations.  This is ugly, but much less work than chaining
a bunch of pages together by hand (suprisingly there's not a bunch of
generic kernel helpers for this yet afaik).  vmalloc space is somewhat
precious on 32 bit kernels, but our allocations shouldn't be big enough
to cause problems, though they're routinely more than a page.

Note that this patch doesn't address the unchecked
alloc-based-on-ioctl-args in GEM; that needs to be fixed in a separate
patch.

Also, I've deliberately ignored the DRM's "area" junk.  I don't think
anyone actually uses it anymore and I'm hoping it gets ripped out soon.

[Updated: removed size arg to new free function.  We could unify the
free functions as well once the DRM mem tracking is ripped out.]

fd.o bug #20152 (part 1/3)

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
2009-05-19 10:07:14 -07:00