This implements the ETHTOOL_SPAUSEPARAM operation for MDIO (clause 45)
PHYs with auto-negotiation MMDs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value. This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.
Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.
This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill. This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.
While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
These two memory barriers in performance-critical paths are not needed
on x86. Even if some other architecture does buffer PCI I/O space
writes, the existing memory-mapped I/O barriers are unlikely to be what
is needed.
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the SQ is flushed, mark the flushed entries as not signaled so
the poll logic doesn't re-insert the CQ entry thinking its an out of
order completion.
The bug can cause the NFS/RDMA server to crash due to processing the
same completed work request twice.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two fixes for DViCO FusionHDTV DVB-T Dual Express:
* Reset correct tuner when reinitializing xc3028.
* Disable the I2C gate control to avoid locking up the I2C bus.
Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set_modeready flag must be set before command sent to USB in
s2255_write_config.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Return actual error values as returned by the i2c subsystem, rather
than 0 or 1.
* If the registration of the second bus fails, unregister the first one
before exiting, otherwise we are leaking resources.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.
The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I lowered the kfree(t) down a couple lines and removed the superflous
"t->vdev = NULL;"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I moved the kfree() down a couple lines. t->vdev is going to be in freed
memory so there is no point setting it to NULL. I added a kfree(t) on a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
selecting ALSA module breaks if !SND. Just remove select.
While here, let's fix the whitespacing at the Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A late v4l2_subdev framework change accidentally sent the audio input
routing value to the external multiplexer, instead of the muxer input routing
value to the external multiplexer. This change corrects that error.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch switches usbhid_close() from flush_scheduled_work() to canceling
the outstanding work. This fixes a possible deadlock due to work taking
the mutex usbhid_close() holds. Lockdep reported the problem.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
--
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
e100: do not go D3 in shutdown unless system is powering off
netfilter: revised locking for x_tables
Bluetooth: Fix connection establishment with low security requirement
Bluetooth: Add different pairing timeout for Legacy Pairing
Bluetooth: Ensure that HCI sysfs add/del is preempt safe
net: Avoid extra wakeups of threads blocked in wait_for_packet()
net: Fix typo in net_device_ops description.
ipv4: Limit size of route cache hash table
Add reference to CAPI 2.0 standard
Documentation/isdn/INTERFACE.CAPI
update Documentation/isdn/00-INDEX
ixgbe: Fix WoL functionality for 82599 KX4 devices
veth: prevent oops caused by netdev destructor
xfrm: wrong hash value for temporary SA
forcedeth: tx timeout fix
net: Fix LL_MAX_HEADER for CONFIG_TR_MODULE
mlx4_en: Handle page allocation failure during receive
mlx4_en: Fix cleanup flow on cq activation
vlan: update vlan carrier state for admin up/down
netfilter: xt_recent: fix stack overread in compat code
...
Quirks for the apple mini keyboard was recently added but keyboard
was recognized as a powerbook keyboard. Adjusted boundary to the lowest
product id for the apple mini keyboard to get the right translation.
Signed-off-by: Ulrich Dangel <uli@spamt.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold. This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds kernel parameter intel_iommu=pt to set up pass through
mode in context mapping entry. This disables DMAR in linux kernel; but
KVM still runs on VT-d and interrupt remapping still works.
In this mode, kernel uses swiotlb for DMA API functions but other VT-d
functionalities are enabled for KVM. KVM always uses multi level
translation page table in VT-d. By default, pass though mode is disabled
in kernel.
This is useful when people don't want to enable VT-d DMAR in kernel but
still want to use KVM and interrupt remapping for reasons like DMAR
performance concern or debug purpose.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Weidong Han <weidong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
o hold the firmware in memory across suspend, since filesystem
may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
for NC-SI.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware starting 4.0.402 started supporting link events, disable
it for older firmwares.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix up error path leak in i915_cmdbuffer
drm/i915: fix unpaired i915 device mutex on entervt failure.
drm/i915: add support for G41 chipset
drm/i915: Enable ASLE if present
drm/i915: Unregister ACPI video driver when exiting
drm/i915: Register ACPI video even when not modesetting
drm/i915: fix transition to I915_TILING_NONE
drm/i915: Don't let an oops get triggered from irq_emit without dma init.
drm/i915: allow tiled front buffers on 965+
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (21 commits)
RDMA/nes: Update iw_nes version
RDMA/nes: Fix error path in nes_accept()
RDMA/nes: Fix hang issues for large cluster dynamic connections
RDMA/nes: Increase rexmit timeout interval
RDMA/nes: Check for sequence number wrap-around
RDMA/nes: Do not set apbvt entry for loopback
RDMA/nes: Fix unused variable compile warning when INFINIBAND_NES_DEBUG=n
RDMA/nes: Fix fw_ver in /sys
RDMA/nes: Set trace length to 1 inch for SFP_D
RDMA/nes: Enable repause timer for port 1
RDMA/nes: Correct CDR loop filter setting for port 1
RDMA/nes: Modify thermo mitigation to flip SerDes1 ref clk to internal
RDMA/nes: Fix resource issues in nes_create_cq() and nes_destroy_cq()
RDMA/nes: Remove root_256()'s unused pbl_count_256 parameter
mlx4_core: Fix memory leak in mlx4_enable_msi_x()
IB/mthca: Fix timeout for INIT_HCA and a few other commands
RDMA/cxgb3: Don't zero QP attrs when moving to IDLE
RDMA/nes: Fix bugs in nes_reg_phys_mr()
RDMA/nes: Fix compiler warning at nes_verbs.c:1955
IPoIB: Disable NAPI while CQ is being drained
...
char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account. Thus, turning on rate debugging
can crash unless we have lucky stack alignment.
Cc: stable@kernel.org
Reported-by: Paride Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
This bug has existed since 2.6.25, reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=12794
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
I am pretty sure that this is a compiler bug, so not to worry. However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed. Correct?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hd dance around local irq and HD_IRQ enable without achieving much.
It ends up transferring data from irq handler with both local irq and
HD_IRQ disabled. The only place it actually does something is while
transferring the first block of a request which it does with HD_IRQ
disabled but local irq enabled.
Unfortunately, the dancing is horribly broken from locking POV. IRQ
and timeout handlers access block queue without grabbing the queue
lock and running the driver in SMP configuration crashes the whole
machine pretty quickly.
Remove meaningless irq enable/disable dancing and add proper locking
in issue, irq and timeout paths.
Signed-off-by: Tejun Heo <tj@kernel.org>
drivers/block/mg_disk.c: In function ‘mg_dump_status’:
drivers/block/mg_disk.c:265: warning: format ‘%ld’ expects type ‘long int’, but
argument 2 has type ‘sector_t’
[ Impact: kill build warning ]
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
IRQ and timeout handlers call functions which expect locked queue lock
without locking it. Fix it.
While at it, convert 0s used as null pointer constant to NULLs.
[ Impact: fix locking, cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: unsik Kim <donari75@gmail.com>
Default voltage constraints were being provided for fixed voltage
regulator where board constraints were not provided but these constraints
used INT_MIN as the default minimum voltage which is not a valid value
since it is less than zero. Use 1uV instead.
Also set the default values we set in the constraints themselves since
otherwise the max_uV constraint we determine will not be stored in the
actual constraint strucutre and will therefore not be used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This seems to be fallout from last October's regulator core rework.
It got noticed only because of recent regulator framework changes.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
During regulator registration, any error after device_register() will
cause a double-free on the struct regulator_dev 'rdev'. The bug is in
drivers/regulator/core.c:regulator_register():
...
scrub:
device_unregister(&rdev->dev);
clean:
kfree(rdev); <---
rdev = ERR_PTR(ret);
goto out;
...
device_unregister() calls regulator_dev_release() which frees rdev. The
subsequent kfree corrupts memory and causes some OMAP3 systems to oops on
boot in regulator_get().
Applies against 2.6.30-rc3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>