82571 and 82572 Errata #13 documents that the Si feature DMA Dynamic
Clock Gating should be disabled, and identifies the workaround of
disabling the feature by EEPROM setting. EEPROM versions that do not
include the recommended workaround have been found in the field, and so
some customers remain at risk. Because the feature DMA Dynamic clock
Gating can be disabled by directly setting the appropriate bit in the
E1000_CTRL_EXT register, this patch overrides the EEPROM setting, and
force-disables the feature.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
most if not all of the devices supported by e1000e support
AER (Advanced Error Reporting) so we attempt to register
with the OS that we know how to reset ourselves after
a fatal error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The poll and flush code needs to handle all send opcodes: SEND,
SEND_WITH_SE, SEND_WITH_INV, and SEND_WITH_SE_INV.
Ignore TERM indications if the connection already gone.
Ignore HW receive completions if the RQ is empty.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The variable 'offset' in iwch_sgl2pbl_map() needs to be a u64.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
bridge: Fix LRO crash with tun
IPv6: fix to set device name when new IPv6 over IPv6 tunnel device is created.
gianfar: Fix boot hangs while bringing up gianfar ethernet
netfilter: xt_sctp: sctp chunk mapping doesn't work
netfilter: ctnetlink: fix echo if not subscribed to any multicast group
netfilter: ctnetlink: allow changing NAT sequence adjustment in creation
netfilter: nf_conntrack_ipv6: don't track ICMPv6 negotiation message
netfilter: fix tuple inversion for Node information request
netxen: fix msi-x interrupt handling
de2104x: force correct order when writing to rx ring
tun: Fix unicast filter overflow
drivers/isdn: introduce missing kfree
drivers/atm: introduce missing kfree
sunhme: Don't match PCI devices in SBUS probe.
9p: fix endian issues [attempt 3]
net_dma: call dmaengine_get only if NET_DMA enabled
3c509: Fix resume from hibernation for PnP mode.
sungem: Soft lockup in sungem on Netra AC200 when switching interface up
RxRPC: Fix a potential NULL dereference
r8169: Don't update statistics counters when interface is down
...
Bits 31-8 are marked as reserved and should be ignored while
interpreting a region's code.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clearing of a vha's req_ques were overrunning during vport
creation. During deletion, vport queues should be torn-down
after all cleanup has occurred.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct response-queue-0 processing by instructing the firmware
to run with interrupt-handshaking disabled, similarly to what is
now done for all non-0 response queues. Since all
response-queues now run in the same mode, the driver no longer
needs the hot-path 'is-disabled-HCCR' test.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Yanling Qi from LSI found the root cause of the panic, below is his
analysis:
Problem description: the open iscsi driver installs eh_timed_out handler
to the
blank_transport_template of the scsi middle level that causes panic of
timed
out command of other host
Here are the details
Iscsi Session creation
During iscsi session creation time, the iscsi_tcp_session_create() of
iscsi_tpc.c will create a scsi-host for the session. See the statement
marked
with the label A. The statement B replaces the shost->transportt point
with a
local struct variable.
static struct iscsi_cls_session *
iscsi_tcp_session_create(struct iscsi_endpoint *ep, uint16_t cmds_max,
uint16_t qdepth, uint32_t initial_cmdsn,
uint32_t *hostno)
{
struct iscsi_cls_session *cls_session;
struct iscsi_session *session;
struct Scsi_Host *shost;
int cmd_i;
if (ep) {
printk(KERN_ERR "iscsi_tcp: invalid ep %p.\n", ep);
return NULL;
}
A shost = iscsi_host_alloc(&iscsi_sht, 0, qdepth);
if (!shost)
return NULL;
B shost->transportt = iscsi_tcp_scsi_transport;
shost->max_lun = iscsi_max_lun;
Please note the scsi host is allocated by invoking isccsi_host_alloc()
in
libiscsi.c
Polluting the middle level blank_transport_template in
iscsi_host_alloc() of
libiscsi.c
The iscsi_host_alloc() invokes the middle level function
scsi_host_alloc() in
hosts.c for allocating a scsi_host. Then the statement marked with C
assigns
the iscsi_eh_cmd_timed_out handler to the eh_timed_out callback
function.
struct Scsi_Host *iscsi_host_alloc(struct scsi_host_template *sht,
int dd_data_size, uint16_t qdepth)
{
struct Scsi_Host *shost;
struct iscsi_host *ihost;
shost = scsi_host_alloc(sht, sizeof(struct iscsi_host) +
dd_data_size);
if (!shost)
return NULL;
C shost->transportt->eh_timed_out = iscsi_eh_cmd_timed_out;
Please note the shost->transport is the middle level
blank_transport_template
as shown in the code segment below. We see two problems here. 1.
iscsi_eh_cmd_timed_out is installed to the blank_transport_template that
will
cause some body else problem. 2. iscsi_eh_cmd_timed_out will never be
invoked
when iscsi command gets timeout because the statement B resets the
pointer.
Middle level blank_transport_template
In the middle level function scsi_host_alloc() of hosts.c, the middle
level
assigns a blank_transport_template for those hosts not implementing its
transport layer. All HBAs without supporting a specific scsi_transport
will
share the middle level blank_transport_template. Please see the
statement D
struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int
privsize)
{
struct Scsi_Host *shost;
gfp_t gfp_mask = GFP_KERNEL;
int rval;
if (sht->unchecked_isa_dma && privsize)
gfp_mask |= __GFP_DMA;
shost = kzalloc(sizeof(struct Scsi_Host) + privsize, gfp_mask);
if (!shost)
return NULL;
shost->host_lock = &shost->default_lock;
spin_lock_init(shost->host_lock);
shost->shost_state = SHOST_CREATED;
INIT_LIST_HEAD(&shost->__devices);
INIT_LIST_HEAD(&shost->__targets);
INIT_LIST_HEAD(&shost->eh_cmd_q);
INIT_LIST_HEAD(&shost->starved_list);
init_waitqueue_head(&shost->host_wait);
mutex_init(&shost->scan_mutex);
shost->host_no = scsi_host_next_hn++; /* XXX(hch): still racy */
shost->dma_channel = 0xff;
/* These three are default values which can be overridden */
shost->max_channel = 0;
shost->max_id = 8;
shost->max_lun = 8;
/* Give each shost a default transportt */
D shost->transportt = &blank_transport_template;
Why we see panic at iscsi_eh_cmd_timed_out()
The mpp virtual HBA doesn’t have a specific scsi_transport. Therefore,
the
blank_transport_template will be assigned to the virtual host of the MPP
virtual HBA by SCSI middle level. Please note that the statement C has
assigned
iscsi-transport eh_timedout handler to the blank_transport_template.
When a mpp
virtual command gets timedout, the iscsi_eh_cmd_timed_out() will be
invoked to
handle mpp virtual command timeout from the middle level
scsi_times_out()
function of the scsi_error.c.
enum blk_eh_timer_return scsi_times_out(struct request *req)
{
struct scsi_cmnd *scmd = req->special;
enum blk_eh_timer_return (*eh_timed_out)(struct scsi_cmnd *);
enum blk_eh_timer_return rtn = BLK_EH_NOT_HANDLED;
scsi_log_completion(scmd, TIMEOUT_ERROR);
if (scmd->device->host->transportt->eh_timed_out)
E eh_timed_out =
scmd->device->host->transportt->eh_timed_out;
else if (scmd->device->host->hostt->eh_timed_out)
eh_timed_out = scmd->device->host->hostt->eh_timed_out;
else
eh_timed_out = NULL;
if (eh_timed_out) {
rtn = eh_timed_out(scmd);
It is very easy to understand why we get panic in the
iscsi_eh_cmd_timed_out().
A scsi_cmnd from a no-iscsi device definitely can not resolve out a
session and
session->lock. The panic can be happed anywhere during the differencing.
static enum blk_eh_timer_return iscsi_eh_cmd_timed_out(struct scsi_cmnd
*scmd)
{
struct iscsi_cls_session *cls_session;
struct iscsi_session *session;
struct iscsi_conn *conn;
enum blk_eh_timer_return rc = BLK_EH_NOT_HANDLED;
cls_session = starget_to_session(scsi_target(scmd->device));
session = cls_session->dd_data;
debug_scsi("scsi cmd %p timedout\n", scmd);
spin_lock(&session->lock);
This patch fixes the problem by moving the setting of the
iscsi_eh_cmd_timed_out to iscsi_add_host, which is after the LLDs
have set their transport template to shost->transportt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During cancel testing it has been shown that 15 seconds is not
nearly long enough for the VIOS to respond to a cancel under
loaded situations. Increasing this timeout to 60 seconds allows
time for the VIOS to cancel the outstanding commands and prevents
us from escalating to a full host reset, which can take much longer.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver has a bug in its SCN handling. If it receives
an ELS event such asn an N-Port SCN event or an unsolicited PLOGI,
or any other SCN event which causes ibmvfc_reinit_host to be called,
it is possible that we will call fc_remote_port_add for a target
that already has an rport added, which can result in duplicate
rports getting created for the same targets. Fix this by calling
fc_remote_port_rolechg in this scenario instead to report any possible
role change that may have occurred.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the ibmvfc driver sets the IBMVFC_CLASS_3_ERR flag
in the VFC Frame if both the adapter and the device claim support
for Class 3. However, this bit actually refers to Class 3 Error
Recovery, which is currently not supported by the VIOS. Setting this
bit can cause lots of command timeout responses from the VIOS resulting
in general instability. Fix this by never setting this bit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hi,
we have run into an issue with blktrace being started for sg devices.
Please apply.
Thanks,
Martin
From: Martin Peschke <mpeschke@linux.vnet.ibm.com>
The device number denoting a generic SCSI devices (sg) in a blktrace
trace is broken; major and minor are always 0. It looks like
sdp->device->sdev_gendev.devt is not initialized properly.
The fix below uses other data to make up a valid device number,
similar to the way an sg device number is generated for sysfs output.
Reported-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were running i/o and performing a bunch of hba resets in a loop.
This forces a lot of target removes and then rescans. Since the
resets are occuring during scan it's causing the scan i/o to timeout,
invoking error recovery, etc. We end up getting some nasty crashing
in scsi_scan.c due to references to old sdevs that are failing
but had some lingering references that kept them around.
Fix by setting device state to SDEV_DEL if the LLD's slave_alloc
fails.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi client driver is not unmapping the SCSI command after
encountering a DMA mapping error while trying to map an indirect
scattergather list for the event pool. This leads to a leak of DMA
entitlement that could result in the device failing future DMA operations
in a CMO environment.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for the E-Ink Broadsheet display controller.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tx_timeout reset path needs to re-init dev and re-apply nic cfg to
enable vlan stripping.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report all bad FCS errs as frames errs. This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns. No longer print a driver msg on bad FCS err.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return notify intr credits after notify intr from firmware. This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP is modular code so no initdata on netns hooks.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ira Snyder found that commit 8c7396aebb
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Storage: Update unusual_devs entry for Datafab KECF-USB
USB: Correct Makefile to make isp1760 buildable
USB: option: New mobile broadband modems to be supported
USB: two more usb ids for ti_usb_3410_5052
USB: ftdi_sio: unlock_kernel() on error in set_serial_info()
USB: usb-storage: add Pentax to the bad-vendor list
USB: ftdi_sio: add support for the NDI Polaris system
USB: usb-serial: fix the aircable_init failure path
USB: usb-storage: remove WARN from last-sector hacks
Revert USB: option: add Pantech cards
USB: cdc-acm.c: remove duplicate lines for MTK gps support
USB: fsl_qe_udc: Fix stalled TX requests bug
USB: fsl_qe_udc: Fix muram corruption by disabled endpoints
USB: fsl_qe_udc: Fix disconnects reporting during bus reset
USB: fsl_qe_udc: Fix QE USB controller initialization
USB: fsl_qe_udc: Fix recursive locking bug in ch9getstatus()
USB: fsl_qe_udc: Fix oops on QE UDC probe failure
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: panel: fix lcd panel driver build failure
Staging: android: fix up units in timed_gpio
Staging: android: ram_console: Disable ECC when early init is enabled and validate buffer size
Staging: at76_usb: Add support for OQO Model 01+
Staging: at76_usb: fix bugs introduced by "Staging: at76_usb: cleanup dma on stack issues"
Revert Staging: at76_usb: update drivers/staging/at76_usb w/ mac80211 port
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Get transition latency from ACPI _PSS table
[CPUFREQ] Make ignore_nice_load setting of ondemand work as expected.
This fixes the crystal frequency calculations in the b2062 init code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few bugs were fixed in the LP baseband init specs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the SSB PMU.
A PMU is found on Low-Power devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 rule flags were being used.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds initialization code for the 2062 radio.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code for the baseband init of LP-PHY >=2.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed led device naming for the iwlwifi (iwl-3945) driver. Due
to the documentation of the led subsystem/class the naming should
be "devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "iwl-%s::RX" instead of "iwl-%s:RX".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed led device naming for the rt2x00 driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "%s::radio" instead of "%s:radio".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed led device naming for the b43legacy driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "b43legacy-%s::rx" instead of
"b43legacy-%s:rx".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed led device naming for the ath9k driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds register definitions for the LP-PHY.
This also adds a few minor empty function bodies for the LP-init.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giving the signal in dB isn't much more useful to userspace
than giving the signal in unspecified units. This removes
some radiotap information for zd1211 (the only driver using
this flag), but it helps a lot for getting cfg80211-based
scanning which won't support dB, and zd1211 being dB is a
little fishy anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>