cx18: Improve handling of outgoing mailboxes detected to be busy. When
encountering a busy mailbox, sleep instead of polling, and wait for interrupt or
timeout. If the mailbox is still busy, force it free. When sending commands,
make sure we never create a situation where we mark the mailbox busy upon
sending, and ensure we always have a method to cleanly recover from a busy
mailbox.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver interrupt and mailbox handling has change significantly.
Time for a roll to v1.0.2.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add mutexes to ensure exclusive access for outgoing driver to CX23418 mailboxes.
Also wait on a waitq for mailbox acknowledgement from the CX23418 instead of
polling.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use default kernel work queue; fix streaming flag for work handler.
Eliminate cx18 specific work queue and use the kernel default work queue.
Fixed the F_STREAMING_FLAG for the TS stream so cx18_dvb_work_handler()
can know when it is not safe to send MDLs to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Reduce number of mmio read retries to improve performance. Experiments
have shown 2 things: read retries never improve the result of a suspect mmio
read from the CX23418 (the result stays all 0xff's), and that most of the
suspected read failures are actually proper reads of values that should be
all 0xff's. This change reduces the number of read retries and keeps the
count separate from write retries.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use usb_endpoint_xfer_int(epd) instead of open-conding the check.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the SEGA Dreamcast Maple controller as a joystick
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some Dells need the dell input quirk applied but have a different vendor
string in their DMI tables. Add an extra entry to cover these machines as
well.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add MODULE_ALIAS() to the HIL keyboard (hil_kbd.c) and HIL mouse
(hil_ptr.c) drivers to make kernel module autoloader functional.
Report HIL port number ID in serio id.id field.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 38617c64 ("RDMA/addr: Add support for translating IPv6
addresses") broke the build when CONFIG_IPV6=n, because the ib_addr
module unconditionally attempted to call ipv6_chk_addr() and other
IPv6 functions that are not defined when IPv6 is disabled. Fix this
by only building IPv6 support if CONFIG_IPV6 is turned on, and
add a Kconfig dependency to prevent the ib_addr code from being built
in when IPv6 is built modular.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
In drivers/net/wireless/zd1211rw/zd_usb.c the code:
(endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT
is suspicious. If it is intended to use USB_ENDPOINT_DIR_MASK rather than
USB_TYPE_MASK, then the whole conditional test could be converted to a call
to usb_endpoint_is_bulk_in.
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Windows compatibility, return an implicit integer of value
zero for methods that have no executable code. A default implicit
value of zero is provided for methods. Lin Ming.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge the code that validates control method argument counts into
the predefined validation module. Eliminates possible multiple
warnings for incorrect counts.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For predefined methods (such as _BIF), add automatic conversion for
objects that are required to be a String, but a Buffer was found
instead. This can happen when reading string battery data from
an operation region, because it used to be difficult to convert
the data from buffer to string from within the ASL. Linux BZ 11822.
http://bugzilla.kernel.org/show_bug.cgi?id=11822
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In a fully qualified namepath, allow multiple backslash prefixes.
This can happen because of the use of a double-backslash in strings
(since backslash is the escape character) causing confusion.
ACPICA BZ 739 Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=739
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where the use of an alias within a namepath
would result in a not found error or cause the compiler to fault.
Also now allows forward references from the Alias operator itself.
ACPICA BZ 738.
http://www.acpica.org/bugzilla/show_bug.cgi?id=738
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This define is no longer used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current implemenation of _OSI within ACPICA only allows other
control methods to execute _OSI. This change allows the host
OS to execute _OSI via the AcpiEvaluateObject interface. _OSI
is a special method -- it does not exist in the AML code, it is
implemented within ACPICA.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat comments to use fewer lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a global pointer instead of using AcpiGetTableByIndex for
each FACS access. This simplifies the code for the Global Lock
and the Firmware Waking Vector(s).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Checks if there are two valid but different addresses for the
FACS and DSDT within the FADT (mismatch between the 32-bit and
64-bit fields.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes the name of this address space, changing it from the
incorrect CMOS to the correct SystemCMOS.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split the "data register I/O" with more informative read and
write messages.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a loop counter to force exit from AML While loops if the
count becomes too large. This can occur in poorly written AML
when the hardware does not respond within a while loop and the
loop does not implement a timeout. The maximum loop count is
configurable. A new exception code is returned when a loop is
broken, AE_AML_INFINITE_LOOP. Bob Moore, Alexey Starikovskiy.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, a control state object was allocated and freed for
each execution of the loop. The optimization is to simply reuse
the control state for each iteration. This speeds up the raw loop
execution time by about 5%.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible memory leak if an allocation failure happens in
the parse loop. Must terminate an executing control method.
Lin Ming, Bob Moore. ACPICA BZ 489.
http://www.acpica.org/bugzilla/show_bug.cgi?id=489
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split AcpiSetFirmwareWakingVector into two: one for the 32-bit
vector, another for the 64-bit vector. This is required because the
host OS must setup the wake much differently for each vector (real
vs. protected mode, etc.) and the interface should not be deciding
which vector to use. Also eliminate the GetFirmwareWakingVector
interface, as it served no purpose (only the firmware reads the
vector, OS only writes the vector.) ACPICA BZ 731.
http://www.acpica.org/bugzilla/show_bug.cgi?id=731
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New compiler is pickier than older versions.
Joerg Sonnenberger. From ACPICA BZ 732.
http://www.acpica.org/bugzilla/show_bug.cgi?id=732
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
in drivers/net/eexpress.c:558, function unstick_cu()
while (!SCB_complete(rsst=scb_status(dev))) {
...
if (...)
printk(KERN_WARNING "%s: Reset timed out status %04x, retrying...\n",
dev->name,rsst);
}
but this will become
while (!((rsst = scb_status(dev) & 0x8000) != 0) ...
because of the macro:
#define SCB_complete(s) ((s&0x8000)!=0)
so rsst can only become either 0x8000 or 0, but in the latter case the
loop ends, I think the wrong timed out status is printed. This also
cleans up similar macros.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now using Ethtool to determine ring sizes, removed the module parameters
that controlled those values.
Modifying ring size requires restart of the interface.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed module parameter specifying number of RX rings
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Required in cases were dev->caps.num_comp_vectors > MAX_RX_RINGS.
For current values this would happen on machines that have more
then 16 cores.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated include in drivers/net/arm/ks8695net.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I hit similar build failure due to the change in the netif_rx_reschedule()
drivers/net/ehea/ehea_main.c: In function 'ehea_poll':
drivers/net/ehea/ehea_main.c:844: warning: passing argument 1 of 'netif_rx_reschedule' from incompatible pointer type
drivers/net/ehea/ehea_main.c:844: error: too many arguments to function 'netif_rx_reschedule'
make[3]: *** [drivers/net/ehea/ehea_main.o] Error 1
greping through the sources for the changes missed out, we have
./drivers/net/arm/ixp4xx_eth.c:507: netif_rx_reschedule(dev, napi)) {
./drivers/net/arm/ep93xx_eth.c:310: if (more && netif_rx_reschedule(dev, napi))
./drivers/net/wan/ixp4xx_hss.c:657: netif_rx_reschedule(dev, napi)) {
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bus_id is gradually being removed, so use dev_name() instead.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch moves the initial guest page table creation code to the host,
so the launcher keeps working with PAE enabled configs.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch implements config_changed for the s390 virtio transport.
We use the least significant bit of the interrupt parameter field
to decide, if this interrupt should call the virtio virtqueue callback
or the config_changed callback.
This method is compatible with old host and guest code. Old 64 bit guests
will not check the bit and trigger a harmless additional vring_interrupt
call. Old host code will never set this bit, this is also safe.
This patch also takes care of a potential future 31 bit virtio transport
for s390. On 31 bit _LC_PFAULT_INTPARM and __LC_EXT_PARAMS are identical.
We exploit the alignment of the token and fold the change bit into the
lsb of the token itself.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
this patch uses the new hvc callback hvc_resize to set the window size
which allows to change the tty size of hvc_console via a hvc_resize
function.
I have added a new feature bit VIRTIO_CONSOLE_F_SIZE. The driver will
change the window size on tty open and via the config_changed callback
of the transport. Currently lguest and kvm_s390 have not implemented this
callback, but the callback can be implemented at a later point in time.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a release() function for virtio_pci devices so as to avoid:
Device 'virtio0' does not have a release() function, it is broken and must be fixed
Move the code to free the resources associated with the device
from virtio_pci_remove() into this new function. virtio_pci_remove()
now merely unregisters the device which should cause the final
ref to be dropped and virtio_pci_release_dev() to be called.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix parameter type warning:
linux-next-20081126/drivers/block/virtio_blk.c:307: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Enhance the driver to handle whatever maximum segment number the host
tells us to handle. Do to this, we need to allocate the scatterlist
dynamically.
We set max_phys_segments and max_hw_segments to the same value (1 if
the host doesn't tell us, since that's safest and all known hosts do
tell us).
Note that kmalloc'ing the structure for large sg_elems might be
problematic: the fix for this is sg_table, but that requires more
work.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Setting max_segment_size allows more than 64k per sg element, unless
the host specified a limit. Setting max_sectors indicates that our
max_hw_segments is the only limit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>