Commit graph

2,238 commits

Author SHA1 Message Date
Damon Ding
e0735bfd5d drm/bridge: analogix_dp: Apply DP helper API drm_dp_clock_recovery_ok()
Use existing DP helper API instead of analogix_dp_clock_recovery_ok()
with the same function.

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251110085823.1197472-3-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-25 14:05:09 +01:00
Damon Ding
b97a424b09 drm/bridge: analogix_dp: Apply DP helper API drm_dp_dpcd_read_link_status()
Use existing DP helper API to read link status related DPCDs.

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251110085823.1197472-2-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-25 14:05:08 +01:00
Damon Ding
05d09e7f28 drm/bridge: analogix_dp: Reuse &link_train.training_lane[] to set DPCD DP_TRAINING_LANEx_SET
In analogix_dp_link_start(), &link_train.training_lane[] is used to
set phy PE/VS configurations, and buf[] is initialized with the same
values to set DPCD DP_TRAINING_LANEx_SET.

It makes sense to reuse &link_train.training_lane[] to set DPCD
DP_TRAINING_LANEx_SET, which can remove the redundant assignments
and make codes more concise.

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251111022103.1350183-1-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-25 12:57:55 +01:00
Arnd Bergmann
c196276f78 drm/bridge: lt8713sx: avoid 64-bit division
On 32-bit kernels, 64-bit integers cannot be passed to the division operator:

ld.lld-22: error: undefined symbol: __aeabi_uldivmod
>>> referenced by lontium-lt8713sx.c
>>>               drivers/gpu/drm/bridge/lontium-lt8713sx.o:(lt8713sx_firmware_store) in archive vmlinux.a

Since this is a constant number used to divide a size_t, just change the type
to that as well.

Fixes: 4037c6adc1 ("drm/bridge: add support for lontium lt8713sx bridge driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316215920.1993390-1-arnd@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-25 04:25:26 +02:00
Arnd Bergmann
9a9d5ceff9 drm/bridge: lt8713sx select CONFIG_CRC8
CRC8 needs to be enabled for lt8713sx to build:

ld.lld-22: error: undefined symbol: crc8_populate_msb
>>> referenced by lontium-lt8713sx.c
>>>               drivers/gpu/drm/bridge/lontium-lt8713sx.o:(lt8713sx_probe) in archive vmlinux.a

Fixes: 4037c6adc1 ("drm/bridge: add support for lontium lt8713sx bridge driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260318105130.1969966-1-arnd@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-25 04:25:25 +02:00
Maxime Ripard
00cf406a0a
drm/display: hdmi: Use drm_output_color_format instead of hdmi_colorspace
The hdmi_colorspace enum was defined to represent the colorspace value
of the HDMI infoframes. It was later used by some HDMI drivers to
express the output format they should be setting up.

During the introduction of the HDMI helpers, it then was used to
represent it in the drm_connector_hdmi_state structure.

However, it's always been somewhat redundant with the DRM_COLOR_FORMAT_*
defines, and now with the drm_output_color_format enum. Let's
consolidate around drm_output_color_format in drm_connector_hdmi_state
to facilitate the current effort to provide a global output format
selection mechanism.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-14-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:35 +01:00
Maxime Ripard
4bf05805b6
drm/bridge: synopsys: dw-hdmi: Convert to drm_output_color_format
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.

The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.

The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.

Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-9-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:33 +01:00
Maxime Ripard
04b4e39a14
drm/bridge: synopsys: dw-dp: Convert to drm_output_color_format
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.

The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.

The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-8-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:32 +01:00
Maxime Ripard
a90bd3baff
drm/bridge: cadence: Convert to drm_output_color_format
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.

The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.

The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-7-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:32 +01:00
Maxime Ripard
97f71dac35
drm/bridge: analogix: Convert to drm_output_color_format
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.

The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.

The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-6-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:31 +01:00
Maxime Ripard
be7d12f878
drm/bridge: adv7511: Convert to drm_output_color_format
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.

The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.

The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-5-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-03-24 13:54:31 +01:00
Luca Ceresoli
fbef867cf6 drm/bridge: samsung-dsim: use drm_bridge_clear_and_put() to put the next bridge
drm_bridge_clear_and_put() is simpler to write and it prevents any
potential future use-after-free.

Reviewed-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260310-drm-bridge-atomic-vs-remove-clear_and_put-v2-2-51fe222f3cf0@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-20 11:02:12 +01:00
Ethan Tidmore
a469749640 drm/bridge: waveshare-dsi: Fix signedness bug
The function drm_of_get_data_lanes_count_ep() returns negative error
codes and dsi->lanes is an unsigned integer, so the check (dsi->lanes <
0) is always impossible.

Make the return value of drm_of_get_data_lanes_count_ep() be assigned to
ret, check for error, and then assign dsi->lanes to ret.

Detected by Smatch:
drivers/gpu/drm/bridge/waveshare-dsi.c:70 ws_bridge_attach_dsi() warn:
unsigned 'dsi->lanes' is never less than zero.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202603060341.hNj0pl9L-lkp@intel.com/
Fixes: fca1142842 ("drm/bridge: waveshare-dsi: Add support for 1..4 DSI data lanes")
Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260307033245.71666-1-ethantidmore06@gmail.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-17 18:04:08 +01:00
Vishnu Saini
4037c6adc1 drm/bridge: add support for lontium lt8713sx bridge driver
The lt8713sx is a Type-C/DP1.4 to DP1.4/HDMI2.0 converter,
with three configurable DP1.4/HDMI2.0/DP++ output interfaces and
audio output interface.

Driver is required for firmware upgrade and enabling the bridge chip.

Co-developed-by: Prahlad Valluru <vvalluru@qti.qualcomm.com>
Signed-off-by: Prahlad Valluru <vvalluru@qti.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Cc: Simon Zhu <xmzhu@lontium.corp-partner.google.com>
Link: https://patch.msgid.link/20260303-lt8713sx-bridge-driver-v5-2-6cc2a855aafa@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-14 03:49:43 +02:00
Dmitry Baryshkov
91d045058c drm: bridge: anx7625: correctly detect if PD can be disabled
During initial checks the ANX7625 bridge can be powered on before
setting up the Type-C port. At this point, when
anx7625_ocm_loading_check() checks if it can disable PD or not, it will
notice that typec_port is not set and disable PD, breaking orientation
and HPD handling. Unify the check between anx7625_ocm_loading_check()
anx7625_i2c_probe() and anx7625_typec_register() and check for the
presence of the "connector" node.

Fixes: 8ad0f7d2e6 ("drm: bridge: anx7625: implement message sending")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260211-anx7625-fix-pd-v1-1-1dd31451b06f@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-11 04:19:13 +02:00
Loic Poulain
8e3d8b3385 drm: bridge: anx7625: don't crash if Type-C port is not used
The typec_set_*() functions do not tolerate being passed the NULL
typec_port instance. However, if CONFIG_TYPEC is enabled, but anx7625
DT node doesn't have the usb-c connector fwnode, then typec_port remains
NULL, crashing the kernel. Prevent calling typec_set_foo() functions by
checking that ctx->typec_port is not NULL in anx7625_typec_set_status().

 Call trace:
  typec_set_orientation+0x18/0x68 (P)
  anx7625_typec_set_status+0x108/0x13c
  anx7625_work_func+0x124/0x438
  process_one_work+0x214/0x648
  worker_thread+0x1b4/0x358
  kthread+0x14c/0x214
  ret_from_fork+0x10/0x20
 Code: 910003fd a90153f3 aa0003f3 2a0103f4 (f9431400)

Fixes: f81455b2d3 ("drm: bridge: anx7625: implement minimal Type-C support")
Reported-by: Salendarsingh Gaud <sgaud@qti.qualcomm.com>
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
[db: dropped chunk anx7625_typec_unregister(), wrote commit message]
Cc: Amit Kucheria <akucheri@qti.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260215-anx-fix-no-typec-v1-1-75172a5ca88b@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-11 04:18:48 +02:00
Arnd Bergmann
10e9ff46fe drm: bridge: anx7625: enforce CONFIG_USB_ROLE_SWITCH dependency
When CONFIG_TYPEC is enabled, but USB_ROLE_SWITCH=m, the anx7625 driver
fails to link as built-in:

aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/anx7625.o: in function `anx7625_i2c_remove':
anx7625.c:(.text+0x6ec): undefined reference to `usb_role_switch_put'
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/anx7625.o: in function `anx7625_typec_set_status':
anx7625.c:(.text+0x3080): undefined reference to `usb_role_switch_set_role'
aarch64-linux-ld: drivers/gpu/drm/bridge/analogix/anx7625.o: in function `anx7625_i2c_probe':
anx7625.c:(.text+0x5368): undefined reference to `fwnode_usb_role_switch_get'

The problem is that both dependencies are optional in the sense of allowing
the anx7625 driver to call the exported interfaces to be used from a loadable
module, but cannot work for built-in drivers. It would be possible to handle
all nine combinations of the CONFIG_TYPEC and CONFIG_USB_ROLE_SWITCH tristate
options, but that does add a lot of complexity that seems unnecessary when
in reality any user of this driver would have both enabled anyway.

Turn both dependencies into hard 'depends on' here to only allow configurations
where it's possible to actually use them, and remove the misguided IS_REACHABLE()
check that did nothing here.

Fixes: f81455b2d3 ("drm: bridge: anx7625: implement minimal Type-C support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260304083604.724519-1-arnd@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-03-11 04:18:23 +02:00
Jayesh Choudhary
bfb18fd193 drm/bridge: cadence: cdns-mhdp8546-core: Reduce log level for DPCD read/write
Reduce the log level for cdns_mhdp_dpcd_read and cdns_mhdp_dpcd_write
errors in cdns_mhdp_transfer function as in case of failure, there is
flooding of these prints along with other indicators like EDID failure
logs which are fairly intuitive in themselves rendering these error logs
useless.
Also, the caller functions for the cdns_mhdp_transfer in drm_dp_helper.c
(which calls it 32 times), has debug log level in case transfer fails.
So having a superseding log level in cdns_mhdp_transfer seems bad.

Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251209120332.3559893-7-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Jayesh Choudhary
0d9e84d304 cadence: cdns-mhdp8546*: Change drm_connector from structure to pointer
Now that we have dropped the legacy code which became redundant with
introduction of DRM_BRIDGE_ATTACH_NO_CONNECTOR
usecase in driver,we can cleanly switch to drm_connector pointer
instead of structure.

Rename the connector_ptr member variable to connector for clarity and
consistency. The driver was using both connector and connector_ptr members,
but connector_ptr was the only one actually used throughout the code.
This change removes the unused connector struct member and renames
connector_ptr to connector for better readability.

This is purely a code cleanup change with no functional impact. All
references to connector_ptr are updated to use the renamed connector
variable throughout the driver.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patch.msgid.link/20251209120332.3559893-6-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Jayesh Choudhary
35cf255452 drm/bridge: cadence: cdns-mhdp8546-core: Remove legacy support for connector initialisation in bridge
Now that this bridge supports DRM_BRIDGE_ATTACH_NO_CONNECTOR,
and only TI K3 platforms consume this driver and
tidss (their display controller) has DRM_BRIDGE_ATTACH_NO_CONNECTOR
flag set,we can remove the legacy code for the
non-DRM_BRIDGE_ATTACH_NO_CONNECTOR case.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patch.msgid.link/20251209120332.3559893-5-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Harikrishna Shenoy
4a8edd6584 drm/bridge: cadence: cdns-mhdp8546-core: Handle HDCP state in bridge atomic check
Now that we have DRM_BRIDGE_ATTACH_NO_CONNECTOR framework, handle the
HDCP state change in bridge atomic check as well to enable correct
functioning for HDCP in both DRM_BRIDGE_ATTACH_NO_CONNECTOR and
!DRM_BRIDGE_ATTACH_NO_CONNECTOR case.

Without this patch, when using DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, HDCP
state changes would not be properly handled during atomic commits,
potentially leading to HDCP authentication failures or incorrect
protection status for content requiring HDCP encryption.

Fixes: 6a3608eae6 ("drm: bridge: cdns-mhdp8546: Enable HDCP")
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patch.msgid.link/20251209120332.3559893-4-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Jayesh Choudhary
6dbff34016 drm/bridge: cadence: cdns-mhdp8546-core: Add mode_valid hook to drm_bridge_funcs
Add cdns_mhdp_bridge_mode_valid() to check if specific mode is valid for
this bridge or not. In the legacy usecase with
!DRM_BRIDGE_ATTACH_NO_CONNECTOR we were using the hook from
drm_connector_helper_funcs but with DRM_BRIDGE_ATTACH_NO_CONNECTOR
we need to have mode_valid() in drm_bridge_funcs.

Without this patch, when using DRM_BRIDGE_ATTACH_NO_CONNECTOR
flag, the cdns_mhdp_bandwidth_ok() function would not be called
during  mode validation, potentially allowing modes that exceed
the bridge's bandwidth capabilities to be incorrectly marked as
valid.

Fixes: c932ced6b5 ("drm/tidss: Update encoder/bridge chain connect model")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251209120332.3559893-3-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Jayesh Choudhary
43d6508ddb drm/bridge: cadence: cdns-mhdp8546-core: Set the mhdp connector earlier in atomic_enable()
In case if we get errors in cdns_mhdp_link_up() or cdns_mhdp_reg_read()
in atomic_enable, we will go to cdns_mhdp_modeset_retry_fn() and will hit
NULL pointer while trying to access the mutex. We need the connector to
be set before that. Unlike in legacy cases with flag
!DRM_BRIDGE_ATTACH_NO_CONNECTOR, we do not have connector initialised
in bridge_attach(), so add the mhdp->connector_ptr in device structure
to handle both cases with DRM_BRIDGE_ATTACH_NO_CONNECTOR and
!DRM_BRIDGE_ATTACH_NO_CONNECTOR, set it in atomic_enable() earlier to
avoid possible NULL pointer dereference in recovery paths like
modeset_retry_fn() with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag set.

Fixes: c932ced6b5 ("drm/tidss: Update encoder/bridge chain connect model")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patch.msgid.link/20251209120332.3559893-2-h-shenoy@ti.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-09 18:57:19 +01:00
Marek Vasut
fca1142842 drm/bridge: waveshare-dsi: Add support for 1..4 DSI data lanes
Parse the data lane count out of DT. Limit the supported data lanes
to 1..4 which is the maximum available DSI pairs on the connector of
any known panels which may use this bridge. Internally, this bridge
is an ChipOne ICN6211 which loads its register configuration from a
dedicated storage and its I2C does not seem to be accessible. The
ICN6211 also supports up to 4 DSI lanes, so this is a hard limit.

To avoid any breakage on old DTs where the parsing of data lanes from
DT may fail, fall back to the original hard-coded value of 2 lanes and
warn user.

The lane configuration is preconfigured in the bridge for each of the
WaveShare panels. The 13.3" DSI panel works with 4-lane configuration,
others seem to use 2-lane configuration. This is a hardware property,
so the actual count should come from DT.

Reviewed-by: Joseph Guo <qijian.guo@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260115024004.660986-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-03 14:33:20 +01:00
Thomas Zimmermann
6716101ae4 Merge drm/drm-next into drm-misc-next
Backmerge fixes from v7.0-rc2 into drm-misc-next.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2026-03-03 10:40:37 +01:00
Marek Vasut
b8eb97ead8 drm/bridge: waveshare-dsi: Register and attach our DSI device at probe
In order to avoid any probe ordering issue, the best practice is to move
the secondary MIPI-DSI device registration and attachment to the
MIPI-DSI host at probe time.

Besides solving the probe ordering problems, this makes the bridge work
with R-Car DU. The R-Car DU will attempt to locate the DSI host bridge in
its own rcar_du_probe()->rcar_du_modeset_init()->rcar_du_encoder_init()
by calling of_drm_find_bridge() which calls of_drm_find_and_get_bridge()
and iterates over bridge_list to locate the DSI host bridge.

However, unless the WS driver calls mipi_dsi_attach() in probe(), the
DSI host bridge .attach callback rcar_mipi_dsi_host_attach() is not
called and the DSI host bridge is not added into bridge_list. Therefore
the of_drm_find_and_get_bridge() called from du_probe() will never find
the DSI host bridge and probe will indefinitelly fail with -EPROBE_DEFER.

The circular dependency here is, that if rcar_du_encoder_init() would
manage to find the DSI host bridge, it would call the WS driver .attach
callback ws_bridge_bridge_attach(), but this is too late and can never
happen. This change avoids the circular dependency.

Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260206125801.78705-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-03-03 09:11:14 +01:00
Dave Airlie
21f6bcdf2b drm-misc-next for v7.1:
UAPI Changes:
 
 connector:
 - Add panel_type property
 
 fourcc:
 - Add ARM interleaved 64k modifier
 
 nouveau:
 - Query Z-Cull info with DRM_IOCTL_NOUVEAU_GET_ZCULL_INFO
 
 Cross-subsystem Changes:
 
 coreboot:
 - Clean up coreboot framebuffer support
 
 dma-buf:
 - Provide revoke mechanism for shared buffers
 - Rename move_notify callback to invalidate_mappings and update users.
 - Always enable move_notify
 - Support dma_fence_was_initialized() test
 - Protect dma_fence_ops by RCU and improve locking
 - Fix sparse warnings
 
 Core Changes:
 
 atomic:
 - Allocate drm_private_state via callback and convert drivers
 
 atomic-helper:
 - Use system_percpu_wq
 
 buddy:
 - Make buddy allocator available to all DRM drivers
 - Document flags and structures
 
 colorop:
 - Add destroy helper and convert drivers
 
 fbdev-emulation:
 - Clean up
 
 gem:
 - Fix drm_gem_objects_lookup() error cleanup
 
 Driver Changes:
 
 amdgpu:
 - Set panel_type to OELD for eDP
 
 atmel-hlcdc:
 - Support sana5d65 LCD controller
 
 bridge:
 - anx7625: Support USB-C plus DT bindings
 - connector: Fix EDID detection
 - dw-hdmi-qp: Support Vendor-Specfic and SDP Infoframes; improve others
 - fsl-ldb: Fix visual artifacts plus related DT property 'enable-termination-resistor'
 - imx8qxp-pixel-link: Improve bridge reference handling
 - lt9611: Support Port-B-only input plus DT bindings
 - tda998x: Support DRM_BRIDGE_ATTACH_NO_CONNECTOR; Clean up
 - Support TH1520 HDMI plus DT bindings
 - Clean up
 
 imagination:
 - Clean up
 
 komeda:
 - Fix integer overflow in AFBC checks
 
 mcde:
 - Improve bridge handling
 
 nouveau:
 - Provide Z-cull info to user space
 - gsp: Support GA100
 - Shutdown on PCI device shutdown
 - Clean up
 
 panel:
 - panel-jdi-lt070me05000: Use mipi-dsi multi functions
 - panel-edp: Support Add AUO B116XAT04.1 (HW: 1A); Support CMN N116BCL-EAK (C2); Support FriendlyELEC plus DT changes
 - Fix Kconfig dependencies
 
 panthor:
 - Add tracepoints for power and IRQs
 
 rcar-du:
 - dsi: fix VCLK calculation
 
 rockchip:
 - vop2: Use drm_ logging functions
 - Support DisplayPort on RK3576
 
 sysfb:
 - corebootdrm: Support system framebuffer on coreboot firmware; detect orientation
 - Clean up pixel-format lookup
 
 sun4i:
 - Clean up
 
 tilcdc:
 - Use DT bindings scheme
 - Use managed DRM interfaces
 - Support DRM_BRIDGE_ATTACH_NO_CONNECTOR
 - Clean up a lot of obsolete code
 
 v3d:
 - Clean up
 
 vc4:
 - Use system_percpu_wq
 - Clean up
 
 verisilicon:
 - Support DC8200 plus DT bindings
 
 virtgpu:
 - Support PRIME imports with enabled 3D
 -----BEGIN PGP SIGNATURE-----
 
 iQFPBAABCgA5FiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmmgV6IbFIAAAAAABAAO
 bWFudTIsMi41KzEuMTEsMiwyAAoJEGgNwR1TC3oj3VsH/0xa8RvMN/B882kLA9N2
 Dz9MR3sD3gCKiO3kzLTWncMnvI3qpSZCD/mR86+h7sEh5qiFFSiziZCCEF+BFkpB
 UHK4mawDhMpOQiW+HhTR9V110WVrqtW8jVVg0db9XBE8y7xtj/lV3hv+/1N7WCkg
 9fuxPkXby5cnW6aA8lPYzIdILFknwNVrzYCiPFmc4bXM5uynD0ft7KGR0dgViBIh
 e6IQ+2POz0N0oVOdKGu10wvBQXKOznHpDPRK8844QrLb8CD/W8/mlifeqESDEsM1
 TaPFdupXNdt0jdE2Jb+R+kGWfhM9T+CrtgaQ9LBNTDD8/RO2NrQIxDSYvnKw0DzQ
 jlE=
 =5H3Q
 -----END PGP SIGNATURE-----

Merge tag 'drm-misc-next-2026-02-26' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next

drm-misc-next for v7.1:

UAPI Changes:

connector:
- Add panel_type property

fourcc:
- Add ARM interleaved 64k modifier

nouveau:
- Query Z-Cull info with DRM_IOCTL_NOUVEAU_GET_ZCULL_INFO

Cross-subsystem Changes:

coreboot:
- Clean up coreboot framebuffer support

dma-buf:
- Provide revoke mechanism for shared buffers
- Rename move_notify callback to invalidate_mappings and update users.
- Always enable move_notify
- Support dma_fence_was_initialized() test
- Protect dma_fence_ops by RCU and improve locking
- Fix sparse warnings

Core Changes:

atomic:
- Allocate drm_private_state via callback and convert drivers

atomic-helper:
- Use system_percpu_wq

buddy:
- Make buddy allocator available to all DRM drivers
- Document flags and structures

colorop:
- Add destroy helper and convert drivers

fbdev-emulation:
- Clean up

gem:
- Fix drm_gem_objects_lookup() error cleanup

Driver Changes:

amdgpu:
- Set panel_type to OELD for eDP

atmel-hlcdc:
- Support sana5d65 LCD controller

bridge:
- anx7625: Support USB-C plus DT bindings
- connector: Fix EDID detection
- dw-hdmi-qp: Support Vendor-Specfic and SDP Infoframes; improve others
- fsl-ldb: Fix visual artifacts plus related DT property 'enable-termination-resistor'
- imx8qxp-pixel-link: Improve bridge reference handling
- lt9611: Support Port-B-only input plus DT bindings
- tda998x: Support DRM_BRIDGE_ATTACH_NO_CONNECTOR; Clean up
- Support TH1520 HDMI plus DT bindings
- Clean up

imagination:
- Clean up

komeda:
- Fix integer overflow in AFBC checks

mcde:
- Improve bridge handling

nouveau:
- Provide Z-cull info to user space
- gsp: Support GA100
- Shutdown on PCI device shutdown
- Clean up

panel:
- panel-jdi-lt070me05000: Use mipi-dsi multi functions
- panel-edp: Support Add AUO B116XAT04.1 (HW: 1A); Support CMN N116BCL-EAK (C2); Support FriendlyELEC plus DT changes
- Fix Kconfig dependencies

panthor:
- Add tracepoints for power and IRQs

rcar-du:
- dsi: fix VCLK calculation

rockchip:
- vop2: Use drm_ logging functions
- Support DisplayPort on RK3576

sysfb:
- corebootdrm: Support system framebuffer on coreboot firmware; detect orientation
- Clean up pixel-format lookup

sun4i:
- Clean up

tilcdc:
- Use DT bindings scheme
- Use managed DRM interfaces
- Support DRM_BRIDGE_ATTACH_NO_CONNECTOR
- Clean up a lot of obsolete code

v3d:
- Clean up

vc4:
- Use system_percpu_wq
- Clean up

verisilicon:
- Support DC8200 plus DT bindings

virtgpu:
- Support PRIME imports with enabled 3D

Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260226143615.GA47200@linux.fritz.box
2026-03-02 16:58:07 +10:00
Luca Ceresoli
b99deb6157 drm/bridge: imx8qxp-pixel-link: get/put the next bridge
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated, so move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.

To keep the code as simple and reliable as possible remove the intermediate
next_bridge and selected_bridge variables.

Get/put operations on the remaining pointer is pl->bridge.next_bridge,
which is tied to the struct imx8qxp_pixel_link lifetime, are:
 - get reference when assigned (by of_drm_find_and_get_bridge())
 - put reference before reassignment if reassignment happens
 - put reference when the struct imx8qxp_pixel_link embedding the
   struct drm_bridge is destroyed (struct drm_bridge::next_bridge)

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20260211-drm-bridge-alloc-getput-drm_of_find_bridge-v6-1-651ddfd13bdb@bootlin.com
2026-02-25 10:55:24 +08:00
Maxime Ripard
8b85987d3c
Merge drm/drm-next into drm-misc-next
Let's merge 7.0-rc1 to start the new drm-misc-next window

Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-02-23 11:48:20 +01:00
Maxime Ripard
c17ee635fd
Merge drm/drm-fixes into drm-misc-fixes
7.0-rc1 was just released, let's merge it to kick the new release cycle.

Signed-off-by: Maxime Ripard <mripard@kernel.org>
2026-02-23 10:09:45 +01:00
Linus Torvalds
bf4afc53b7 Convert 'alloc_obj' family to use the new default GFP_KERNEL argument
This was done entirely with mindless brute force, using

    git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
        xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'

to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.

Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.

For the same reason the 'flex' versions will be done as a separate
conversion.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2026-02-21 17:09:51 -08:00
Andy Yan
388bb0899b drm/bridge: synopsys: dw-dp: Make i2s/spdif clk optional
The i2s/spdif clk are mandatory for rk3588, but not used
for the upcoming rk3576, so make it optional here.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260206010421.443605-4-andyshrk@163.com
2026-02-21 23:13:41 +01:00
Andy Yan
77ae37018a drm/bridge: synopsys: dw-dp: Set pixel mode by platform data
In the implementation and integration of the SoC, the DW DisplayPort
hardware block can be configured to work in single, dual, quad pixel
mode on differnt platforms, so make the pixel mode set by plat_data
to support the upcoming rk3576 variant.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260206010421.443605-3-andyshrk@163.com
2026-02-21 23:13:39 +01:00
Kees Cook
69050f8d6d treewide: Replace kmalloc with kmalloc_obj for non-scalar types
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:

Single allocations:	kmalloc(sizeof(TYPE), ...)
are replaced with:	kmalloc_obj(TYPE, ...)

Array allocations:	kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with:	kmalloc_objs(TYPE, COUNT, ...)

Flex array allocations:	kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with:	kmalloc_flex(*PTR, FAM, COUNT, ...)

(where TYPE may also be *VAR)

The resulting allocations no longer return "void *", instead returning
"TYPE *".

Signed-off-by: Kees Cook <kees@kernel.org>
2026-02-21 01:02:28 -08:00
Osama Abdelkader
803ec1faf7 drm/bridge: samsung-dsim: Fix memory leak in error path
In samsung_dsim_host_attach(), drm_bridge_add() is called to add the
bridge. However, if samsung_dsim_register_te_irq() or
pdata->host_ops->attach() fails afterwards, the function returns
without removing the bridge, causing a memory leak.

Fix this by adding proper error handling with goto labels to ensure
drm_bridge_remove() is called in all error paths. Also ensure that
samsung_dsim_unregister_te_irq() is called if the attach operation
fails after the TE IRQ has been registered.

samsung_dsim_unregister_te_irq() function is moved without changes
to be before samsung_dsim_host_attach() to avoid forward declaration.

Fixes: e7447128ca ("drm: bridge: Generalize Exynos-DSI driver into a Samsung DSIM bridge")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260209184115.10937-1-osama.abdelkader@gmail.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-20 13:56:14 +01:00
Chen Ni
496daa2759 drm/bridge: synopsys: dw-dp: Check return value of devm_drm_bridge_add() in dw_dp_bind()
Return the value of devm_drm_bridge_add() in order to propagate the
error properly, if it fails due to resource allocation failure or bridge
registration failure.

This ensures that the bind function fails safely rather than proceeding
with a potentially incomplete bridge setup.

Fixes: b726970486 ("drm/bridge: synopsys: dw-dp: add bridge before attaching")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260206040621.4095517-1-nichen@iscas.ac.cn
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-20 13:47:09 +01:00
Hongyang Zhao
e8bd92c4a0 drm/bridge: lt9611: Add support for single Port B input
The LT9611 has two DSI input ports. The driver currently assumes Port A
is always used for single-port configurations. However, some boards
connect DSI to Port B only.

Update the driver to detect which ports are populated from devicetree
and configure the hardware accordingly:

- If only port@1 (Port B) is populated, configure port swap (0x8303
  bit 6) and byte_clk source (0x8250 bit 3:2) for Port B operation
- If both ports are populated, use dual-port mode (Port A + B)
- If only port@0 (Port A) is populated, use single Port A (existing
  behavior)

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Hongyang Zhao <hongyang.zhao@thundersoft.com>
Reviewed-by: Roger Shimizu <rosh@debian.org>
Tested-by: Roger Shimizu <rosh@debian.org>
Link: https://patch.msgid.link/20260207-rubikpi-next-20260116-v3-2-23b9aa189a3a@thundersoft.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-02-14 00:49:42 +02:00
Franz Schnyder
0b87d51690 drm/bridge: ti-sn65dsi86: Enable HPD polling if IRQ is not used
Fallback to polling to detect hotplug events on systems without
interrupts.

On systems where the interrupt line of the bridge is not connected,
the bridge cannot notify hotplug events. Only add the
DRM_BRIDGE_OP_HPD flag if an interrupt has been registered
otherwise remain in polling mode.

Fixes: 55e8ff8420 ("drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type")
Cc: stable@vger.kernel.org # 6.16: 9133bc3f05: drm/bridge: ti-sn65dsi86: Add
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[dianders: Adjusted Fixes/stable line based on discussion]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260206123758.374555-1-fra.schnyder@gmail.com
2026-02-13 12:42:34 -08:00
Linus Torvalds
939faf71cf drm for 7.0-rc1
core:
 - drop kgdb support
 - replace system workqueue with percpu
 - account for property blobs in memcg
 - MAINTAINERS updates for xe + buddy
 
 rust:
 - Fix documentation for Registration constructors.
 - Use pin_init::zeroed() for fops initialization.
 - Annotate DRM helpers with __rust_helper.
 - Improve safety documentation for gem::Object::new().
 - Update AlwaysRefCounted imports.
 - mm: Prevent integer overflow in page_align().
 
 atomic:
 - add drm_device pointer to drm_private_obj
 - introduce gamma/degamma LUT size check
 
 buddy:
 - fix free_trees memory leak
 - prevent BUG_ON
 
 bridge:
 - introduce drm_bridge_unplug/enter/exit
 - add connector argument to .hpd_notify
 - lots of recounting conversions
 - convert rockchip inno hdmi to bridge
 - lontium-lt9611uxc: switch to HDMI audio helpers
 - dw-hdmi-qp: add support for HPD-less setups
 - Algoltek AG6311 support
 
 panels:
 - edp: CSW MNE007QB3-1, AUO B140HAN06.4, AUO B140QAX01.H
 - st75751: add SPI support
 - Sitronix ST7920, Samsung LTL106HL02
 - LG LH546WF1-ED01, HannStar HSD156J
 - BOE NV130WUM-T08
 - Innolux G150XGE-L05
 - Anbernic RG-DS
 
 dma-buf:
 - improve sg_table debugging
 - add tracepoints
 - call clear_page instead of memset
 - start to introduce cgroup memory accounting in heaps
 - remove sysfs stats
 
 dma-fence:
 - add new helpers
 
 dp:
 - mst: avoid oob access with vcpi=0
 
 hdmi:
 - limit infoframes exposure to userspace
 
 gem:
 - reduce page table overhead with THP
 - fix leak in drm_gem_get_unmapped_area
 
 gpuvm:
 - API sanitation for rust bindings
 
 sched:
 - introduce new helpers
 
 panic:
 - report invalid panic modes
 - add kunit tests
 
 i915/xe display:
 - Expose sharpness only if num_scalers is >= 2
 - Add initial Xe3P_LPD for NVL
 - BMG FBC support
 - Add MTL+ platforms to support dpll framework
 _ fix DIMM_S DRM decoding on ICL
 - Return to using AUX interrupts
 - PSR/Panel replay refactoring
 - use consolidation HDMI tables
 - Xe3_LPD CD2X dividier changes
 
 xe:
 - vfio: add vfio_pci for intel GPU
 - multi queue support
 - dynamic pagemaps and multi-device SVM
 - expose temp attribs in hwmon
 - NO_COMPRESSION bo flag
 - expose MERT OA unit
 - sysfs survivability refactor
 - SRIOV PF: add MERT support
 - enable SR-IOV VF migration
 - Enable I2C/NVM on Crescent Island
 - Xe3p page reclaimation support
 - introduce SRIOV scheduler groups
 - add SoC remappt support in system controller
 - insert compiler barriers in GuC code
 - define NVL GuC firmware
 - handle GT resume failure
 - fix drm scheduler layering violations
 - enable GSC loading and PXP for PTL
 - disable GuC Power DCC strategy on PTL
 - unregister drm device on probe error
 
 i915:
 - move to kernel standard fault injection
 - bump recommended GuC version for DG2 and MTL
 
 amdgpu:
 - SMUIO 15.x, PSP 15.x support
 - IH 6.1.1/7.1 support
 - MMHUB 3.4/4.2 support
 - GC 11.5.4/12.1 support
 - SDMA 6.1.4/7.1/7.11.4 support
 - JPEG 5.3 support
 - UserQ updates
 - GC 9 gfx queue reset support
 - TTM memory ops parallelization
 - convert legacy logging to new helpers
 - DC analog fixes
 
 amdkfd:
 - GC 11.5.4/12.1 suppport
 - SDMA 6.1.4/7.1 support
 - per context support
 - increase kfd process hash table
 - Reserved SDMA rework
 
 radeon:
 - convert legacy logging to new helpers
 - use devm for i2c adapters
 
 msm:
 - GPU
   - Document a612/RGMU dt bindings
   - UBWC 6.0 support (for A840 / Kaanapali)
   - a225 support
 - DPU:
   - Switched to use virtual planes by default
   - Fixed DSI CMD panels on DPU 3.x
   - Rewrote format handling to remove intermediate representation
   - Fixed watchdog on DPU 8.x+
   - Fixed TE / Vsync source setting on DPU 8.x+
   - Added 3D_Mux on SC7280
   - Kaanapali platform support
   - Fixed UBWC register programming
   - Made RM reserve DSPP-enabled mixers for CRTCs with LMs.
   - Gamma correction support
 - DP:
   - Enabled support for eDP 1.4+ link rate tables
   - Fixed MDSS1 DP indices on SA8775P, making them to work
   - Fixed msm_dp_ctrl_config_msa() to work with LLVM 20
 - DSI:
   - Documented QCS8300 as compatible with SA8775P
   - Kaanapali platform support
 - DSI PHY:
   - switched to divider_determine_rate()
 - MDP5:
   - Dropped support for MSM8998, SDM660 and SDM630 (switched over
     to DPU)
 -  MDSS:
   - Kaanapali platform support
   - Fixed UBWC register programming
 
 nova-core:
 - Prepare for Turing support. This includes parsing and handling
   Turing-specific firmware headers and sections as well as a Turing
   Falcon HAL implementation.
 - Get rid of the Result<impl PinInit<T, E>> anti-pattern.
 - Relocate initializer-specific code into the appropriate initializer.
 - Use CStr::from_bytes_until_nul() to remove custom helpers.
 - Improve handling of unexpected firmware values.
 - Clean up redundant debug prints.
 - Replace c_str!() with native Rust C-string literals.
 - Update nova-core task list.
 
 nova:
 - Align GEM object size to system page size.
 
 tyr:
 - Use generated uAPI bindings for GpuInfo.
 - Replace manual sleeps with read_poll_timeout().
 - Replace c_str!() with native Rust C-string literals.
 - Suppress warnings for unread fields.
 - Fix incorrect register name in print statement.
 
 nouveau:
 - fix big page table support races in PTE management
 - improve reclocking on tegra 186+
 
 amdxdna:
 - fix suspend race conditions
 - improve handling of zero tail pointers
 - fix cu_idx overwritten during command setup
 - enable hardware context priority
 - remove NPU2 support
 - update message buffer allocation requirements
 - update firmware version check
 
 ast:
 - support imported cursor buffers
 - big endian fixes
 
 etnaviv:
 - add PPU flop reset support
 
 imagination:
 - add AM62P support
 - introduce hw version checks
 
 ivpu:
 - implement warm boot flow
 
 panfrost:
 - add bo sync ioctl
 - add GPU_PM_RT support for RZ/G3E SoC
 
 panthor:
 - add bo sync ioctl
 - enable timestamp propagation
 - scheduler robustness improvements
 - VM termination fixes
 - huge page support
 
 rockchip:
 - RK3368 HDMI Support
 - get rid of atomic_check fixups
 - RK3506 support
 - RK3576/RK3588 improved HPD handling
 
 rz-du:
 - RZ/V2H(P) MIPI-DSI Support
 
 v3d:
 - fix DMA segment size
 - convert to new logging helpers
 
 mediatek:
 - move DP training to hotplug thread
 - convert logging to new helpers
 - add support for HS speed DSI
 - Genio 510/700/1200-EVK, Radxa NIO-12L HDMI support
 
 atmel-hlcdc:
 - switch to drmm resource
 - support nomodeset
 - use newer helpers
 
 hisilicon:
 - fix various DP bugs
 
 renesas:
 - fix kernel panic on reboot
 
 exynos:
 - fix vidi_connection_ioctl using wrong device
 - fix vidi_connection deref user ptr
 - fix concurrency regression with vidi_context
 
 vkms:
 - add configfs support for display configuration
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmmMLAcACgkQDHTzWXnE
 hr7aAw//bQ2WLhXeMqWyqrPPe51l2DmWvbdwP6TKUjzMwd9+xvs6wQcSg80Mn230
 0vqSpqKq2aMB6GMmz7wdHG8JgZOvO7qDf2TZodXe5lvBiAAPjzX+UE/0bIQKuhym
 Ufb7tqCIPsj6TpcD3ef/173x3BnVPA6Y7lS11KaaG5l01vUAVlTD1vfWGDQp/L6P
 7g94cC+0+3eYZyKxE1+Rn7FDXdw08u+vtLchIoowcAHobgucZ8K/XtZZoqFFy3sj
 ZZN580AhyZoGcgmn2KhNvU4B+3tBFFMSVZkJm7skOO0IB2AMQGdEr0uVUDzLGc7K
 DrLaxYwM6HfxM4o0r0Ai0WCuoysCAJ95M2Cp58uDuNcew4lRTtIUqz32Sm2OJ8bD
 Z91Rvh/kOcA0Ru11Sb/kQvy9/OJ54CqojKVaUlkFo9VhHyPCPo9hjnPvaDvCt34N
 FmnhuVpZMWqcjjq5yO/192qpDJnm470eQExvkZ4YpgmWkekND0zwaT4PG4763dZJ
 juPlBQ5WtUlIzlUpRxdHE7C7ht1rWRS+HdzSYPM5aHTXDvktJvcA+1b/Jyicc+x4
 QZiZ/1AC0KKlLrZxpVpEcjkPdQj2CiCXHQ+0YjDfO3cHo/55EfKj4iiARzhDzokf
 h7FgKwvVhc9DycSq8KPGAf09AswceGAtvB1rKk+Jh9D/GqbgGtM=
 =RFJ2
 -----END PGP SIGNATURE-----

Merge tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel

Pull drm updates from Dave Airlie:
 "Highlights:
   - amdgpu support for lots of new IP blocks which means newer GPUs
   - xe has a lot of SR-IOV and SVM improvements
   - lots of intel display refactoring across i915/xe
   - msm has more support for gen8 platforms
   - Given up on kgdb/kms integration, it's too hard on modern hw

  core:
   - drop kgdb support
   - replace system workqueue with percpu
   - account for property blobs in memcg
   - MAINTAINERS updates for xe + buddy

  rust:
   - Fix documentation for Registration constructors
   - Use pin_init::zeroed() for fops initialization
   - Annotate DRM helpers with __rust_helper
   - Improve safety documentation for gem::Object::new()
   - Update AlwaysRefCounted imports
   - mm: Prevent integer overflow in page_align()

  atomic:
   - add drm_device pointer to drm_private_obj
   - introduce gamma/degamma LUT size check

  buddy:
   - fix free_trees memory leak
   - prevent BUG_ON

  bridge:
   - introduce drm_bridge_unplug/enter/exit
   - add connector argument to .hpd_notify
   - lots of recounting conversions
   - convert rockchip inno hdmi to bridge
   - lontium-lt9611uxc: switch to HDMI audio helpers
   - dw-hdmi-qp: add support for HPD-less setups
   - Algoltek AG6311 support

  panels:
   - edp: CSW MNE007QB3-1, AUO B140HAN06.4, AUO B140QAX01.H
   - st75751: add SPI support
   - Sitronix ST7920, Samsung LTL106HL02
   - LG LH546WF1-ED01, HannStar HSD156J
   - BOE NV130WUM-T08
   - Innolux G150XGE-L05
   - Anbernic RG-DS

  dma-buf:
   - improve sg_table debugging
   - add tracepoints
   - call clear_page instead of memset
   - start to introduce cgroup memory accounting in heaps
   - remove sysfs stats

  dma-fence:
   - add new helpers

  dp:
   - mst: avoid oob access with vcpi=0

  hdmi:
   - limit infoframes exposure to userspace

  gem:
   - reduce page table overhead with THP
   - fix leak in drm_gem_get_unmapped_area

  gpuvm:
   - API sanitation for rust bindings

  sched:
   - introduce new helpers

  panic:
   - report invalid panic modes
   - add kunit tests

  i915/xe display:
   - Expose sharpness only if num_scalers is >= 2
   - Add initial Xe3P_LPD for NVL
   - BMG FBC support
   - Add MTL+ platforms to support dpll framework
   _ fix DIMM_S DRM decoding on ICL
   - Return to using AUX interrupts
   - PSR/Panel replay refactoring
   - use consolidation HDMI tables
   - Xe3_LPD CD2X dividier changes

  xe:
   - vfio: add vfio_pci for intel GPU
   - multi queue support
   - dynamic pagemaps and multi-device SVM
   - expose temp attribs in hwmon
   - NO_COMPRESSION bo flag
   - expose MERT OA unit
   - sysfs survivability refactor
   - SRIOV PF: add MERT support
   - enable SR-IOV VF migration
   - Enable I2C/NVM on Crescent Island
   - Xe3p page reclaimation support
   - introduce SRIOV scheduler groups
   - add SoC remappt support in system controller
   - insert compiler barriers in GuC code
   - define NVL GuC firmware
   - handle GT resume failure
   - fix drm scheduler layering violations
   - enable GSC loading and PXP for PTL
   - disable GuC Power DCC strategy on PTL
   - unregister drm device on probe error

  i915:
   - move to kernel standard fault injection
   - bump recommended GuC version for DG2 and MTL

  amdgpu:
   - SMUIO 15.x, PSP 15.x support
   - IH 6.1.1/7.1 support
   - MMHUB 3.4/4.2 support
   - GC 11.5.4/12.1 support
   - SDMA 6.1.4/7.1/7.11.4 support
   - JPEG 5.3 support
   - UserQ updates
   - GC 9 gfx queue reset support
   - TTM memory ops parallelization
   - convert legacy logging to new helpers
   - DC analog fixes

  amdkfd:
   - GC 11.5.4/12.1 suppport
   - SDMA 6.1.4/7.1 support
   - per context support
   - increase kfd process hash table
   - Reserved SDMA rework

  radeon:
   - convert legacy logging to new helpers
   - use devm for i2c adapters

  msm:
   - GPU
      - Document a612/RGMU dt bindings
      - UBWC 6.0 support (for A840 / Kaanapali)
      - a225 support
   - DPU:
      - Switch to use virtual planes by default
      - Fix DSI CMD panels on DPU 3.x
      - Rewrite format handling to remove intermediate representation
      - Fix watchdog on DPU 8.x+
      - Fix TE / Vsync source setting on DPU 8.x+
      - Add 3D_Mux on SC7280
      - Kaanapali platform support
      - Fix UBWC register programming
      - Make RM reserve DSPP-enabled mixers for CRTCs with LMs
      - Gamma correction support
   - DP:
      - Enable support for eDP 1.4+ link rate tables
      - Fix MDSS1 DP indices on SA8775P, making them to work
      - Fix msm_dp_ctrl_config_msa() to work with LLVM 20
   - DSI:
      - Document QCS8300 as compatible with SA8775P
      - Kaanapali platform support
   - DSI PHY:
      - switch to divider_determine_rate()
   - MDP5:
      - Drop support for MSM8998, SDM660 and SDM630 (switch over to DPU)
   -  MDSS:
      - Kaanapali platform support
      - Fixed UBWC register programming

  nova-core:
   - Prepare for Turing support. This includes parsing and handling
     Turing-specific firmware headers and sections as well as a Turing
     Falcon HAL implementation
   - Get rid of the Result<impl PinInit<T, E>> anti-pattern
   - Relocate initializer-specific code into the appropriate initializer
   - Use CStr::from_bytes_until_nul() to remove custom helpers
   - Improve handling of unexpected firmware values
   - Clean up redundant debug prints
   - Replace c_str!() with native Rust C-string literals
   - Update nova-core task list

  nova:
   - Align GEM object size to system page size

  tyr:
   - Use generated uAPI bindings for GpuInfo
   - Replace manual sleeps with read_poll_timeout()
   - Replace c_str!() with native Rust C-string literals
   - Suppress warnings for unread fields
   - Fix incorrect register name in print statement

  nouveau:
   - fix big page table support races in PTE management
   - improve reclocking on tegra 186+

  amdxdna:
   - fix suspend race conditions
   - improve handling of zero tail pointers
   - fix cu_idx overwritten during command setup
   - enable hardware context priority
   - remove NPU2 support
   - update message buffer allocation requirements
   - update firmware version check

  ast:
   - support imported cursor buffers
   - big endian fixes

  etnaviv:
   - add PPU flop reset support

  imagination:
   - add AM62P support
   - introduce hw version checks

  ivpu:
   - implement warm boot flow

  panfrost:
   - add bo sync ioctl
   - add GPU_PM_RT support for RZ/G3E SoC

  panthor:
   - add bo sync ioctl
   - enable timestamp propagation
   - scheduler robustness improvements
   - VM termination fixes
   - huge page support

  rockchip:
   - RK3368 HDMI Support
   - get rid of atomic_check fixups
   - RK3506 support
   - RK3576/RK3588 improved HPD handling

  rz-du:
   - RZ/V2H(P) MIPI-DSI Support

  v3d:
   - fix DMA segment size
   - convert to new logging helpers

  mediatek:
   - move DP training to hotplug thread
   - convert logging to new helpers
   - add support for HS speed DSI
   - Genio 510/700/1200-EVK, Radxa NIO-12L HDMI support

  atmel-hlcdc:
   - switch to drmm resource
   - support nomodeset
   - use newer helpers

  hisilicon:
   - fix various DP bugs

  renesas:
   - fix kernel panic on reboot

  exynos:
   - fix vidi_connection_ioctl using wrong device
   - fix vidi_connection deref user ptr
   - fix concurrency regression with vidi_context

  vkms:
   - add configfs support for display configuration

* tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel: (1610 commits)
  drm/xe/pm: Disable D3Cold for BMG only on specific platforms
  drm/xe: Fix kerneldoc for xe_tlb_inval_job_alloc_dep
  drm/xe: Fix kerneldoc for xe_gt_tlb_inval_init_early
  drm/xe: Fix kerneldoc for xe_migrate_exec_queue
  drm/xe/query: Fix topology query pointer advance
  drm/xe/guc: Fix kernel-doc warning in GuC scheduler ABI header
  drm/xe/guc: Fix CFI violation in debugfs access.
  accel/amdxdna: Move RPM resume into job run function
  accel/amdxdna: Fix incorrect DPM level after suspend/resume
  nouveau/vmm: start tracking if the LPT PTE is valid. (v6)
  nouveau/vmm: increase size of vmm pte tracker struct to u32 (v2)
  nouveau/vmm: rewrite pte tracker using a struct and bitfields.
  accel/amdxdna: Fix incorrect error code returned for failed chain command
  accel/amdxdna: Remove hardware context status
  drm/bridge: imx8qxp-pixel-combiner: Fix bailout for imx8qxp_pc_bridge_probe()
  drm/panel: ilitek-ili9882t: Remove duplicate initializers in tianma_il79900a_dsc
  drm/i915/display: fix the pixel normalization handling for xe3p_lpd
  drm/exynos: vidi: use ctx->lock to protect struct vidi_context member variables related to memory alloc/free
  drm/exynos: vidi: fix to avoid directly dereferencing user pointer
  drm/exynos: vidi: use priv->vidi_dev for ctx lookup in vidi_connection_ioctl()
  ...
2026-02-11 12:55:44 -08:00
Kory Maincent (TI.com)
c76a8be4fe drm/bridge: tda998x: Add support for DRM_BRIDGE_ATTACH_NO_CONNECTOR
Add support for the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag to allow display
controller drivers to create their own connectors. This modernizes the
driver to work with the current DRM bridge framework.

The implementation includes:
- Refactoring detection and EDID reading into bridge-usable helpers
- Adding bridge operations: edid_read, detect, hpd_enable, hpd_disable
- Setting appropriate bridge ops (DRM_BRIDGE_OP_EDID, DRM_BRIDGE_OP_DETECT,
  DRM_BRIDGE_OP_HPD) and connector type (HDMIA)
- Skipping connector creation when DRM_BRIDGE_ATTACH_NO_CONNECTOR is set
- Handling conditional connector cleanup in bridge_detach

The driver maintains backward compatibility by continuing to create its
own connector when the flag is not set.

Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260123-feature_tilcdc-v5-24-5a44d2aa3f6f@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-11 09:16:16 +01:00
Kory Maincent (TI.com)
8ab51f56fd drm/bridge: tda998x: Remove useless tda998x_connector_destroy wrapper
Use directly drm_connector_cleanup in the destroy ops instead of having
a custom function that does nothing more.

Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260123-feature_tilcdc-v5-23-5a44d2aa3f6f@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-11 09:16:16 +01:00
Kory Maincent (TI.com)
22b88deb83 drm/bridge: tda998x: Move tda998x_create/destroy into probe and remove
Now that tda998x_create and tda998x_destroy are called only in the probe
function, there is no need for separate functions.
Move the code into the tda998x_probe and tda998x_remove functions.
Rewrite the cleanup path using goto calls in probe and reorder it in the
remove function.

Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260123-feature_tilcdc-v5-22-5a44d2aa3f6f@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-11 09:16:16 +01:00
Kory Maincent (TI.com)
d700fd0ff1 drm/bridge: tda998x: Remove component support
The tilcdc driver no longer uses the component framework to bind the
tda998x bridge driver. The component bind/unbind operations and the
encoder initialization code are now dead code and can be safely removed.

Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260123-feature_tilcdc-v5-21-5a44d2aa3f6f@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
2026-02-11 09:16:15 +01:00
Linus Torvalds
9b1b3dcd28 Power management updates for 6.20-rc1/7.0-rc1
- Remove the unused omap-cpufreq driver (Andreas Kemnade)
 
  - Optimize error handling code in cpufreq_boost_trigger_state() and
    make cpufreq_boost_trigger_state() return -EOPNOTSUPP if no policy
    supports boost (Lifeng Zheng)
 
  - Update cpufreq-dt-platdev list for tegra, qcom, TI (Aaron Kling,
    Dhruva Gole, and Konrad Dybcio)
 
  - Minor improvements to the cpufreq and cpumask rust implementation
    (Alexandre Courbot, Alice Ryhl, Tamir Duberstein, and Yilin Chen)
 
  - Add support for AM62L3 SoC to the ti-cpufreq driver (Dhruva Gole)
 
  - Update arch_freq_scale in the CPPC cpufreq driver's frequency
    invariance engine (FIE) in scheduler ticks if the related CPPC
    registers are not in PCC (Jie Zhan)
 
  - Assorted minor cleanups and improvements in ARM cpufreq drivers (Juan
    Martinez, Felix Gu, Luca Weiss, and Sergey Shtylyov)
 
  - Add generic helpers for sysfs show/store to cppc_cpufreq (Sumit
    Gupta)
 
  - Make the scaling_setspeed cpufreq sysfs attribute return the actual
    requested frequency to avoid confusion (Pengjie Zhang)
 
  - Simplify the idle CPU time granularity test in the ondemand cpufreq
    governor (Frederic Weisbecker)
 
  - Enable asym capacity in intel_pstate only when CPU SMT is not
    possible (Yaxiong Tian)
 
  - Update the description of rate_limit_us default value in cpufreq
    documentation (Yaxiong Tian)
 
  - Add a command line option to adjust the C-states table in the
    intel_idle driver, remove the 'preferred_cstates' module parameter
    from it, add C-states validation to it and clean it up (Artem
    Bityutskiy)
 
  - Make the menu cpuidle governor always check the time till the closest
    timer event when the scheduler tick has been stopped to prevent it
    from mistakenly selecting the deepest available idle state (Rafael
    Wysocki)
 
  - Update the teo cpuidle governor to avoid making suboptimal decisions
    in certain corner cases and generally improve idle state selection
    accuracy (Rafael Wysocki)
 
  - Remove an unlikely() annotation on the early-return condition in
    menu_select() that leads to branch misprediction 100% of the time
    on systems with only 1 idle state enabled, like ARM64 servers (Breno
    Leitao)
 
  - Add Christian Loehle to MAINTAINERS as a cpuidle reviewer (Christian
    Loehle)
 
  - Stop flagging the PM runtime workqueue as freezable to avoid system
    suspend and resume deadlocks in subsystems that assume asynchronous
    runtime PM to work during system-wide PM transitions (Rafael Wysocki)
 
  - Drop redundant NULL pointer checks before acomp_request_free() from
    the hibernation code handling image saving (Rafael Wysocki)
 
  - Update wakeup_sources_walk_start() to handle empty lists of wakeup
    sources as appropriate (Samuel Wu)
 
  - Make dev_pm_clear_wake_irq() check the power.wakeirq value under
    power.lock to avoid race conditions (Gui-Dong Han)
 
  - Avoid bit field races related to power.work_in_progress in the core
    device suspend code (Xuewen Yan)
 
  - Make several drivers discard pm_runtime_put() return value in
    preparation for converting that function to a void one (Rafael
    Wysocki)
 
  - Add PL4 support for Ice Lake to the Intel RAPL power capping
    driver (Daniel Tang)
 
  - Replace sprintf() with sysfs_emit() in power capping sysfs show
    functions (Sumeet Pawnikar)
 
  - Make dev_pm_opp_get_level() return value match the documentation
    after a previous update of the latter (Aleks Todorov)
 
  - Use scoped for each OF child loop in the OPP code (Krzysztof
    Kozlowski)
 
  - Fix a bug in an example code snippet and correct typos in the energy
    model management documentation (Patrick Little)
 
  - Fix miscellaneous problems in cpupower (Kaushlendra Kumar):
 
    * idle_monitor: Fix incorrect value logged after stop
    * Fix inverted APERF capability check
    * Use strcspn() to strip trailing newline
    * Reset errno before strtoull()
    * Show C0 in idle-info dump
 
  - Improve cpupower installation procedure by making the systemd step
    optional and allowing users to disable the installation of systemd's
    unit file (João Marcos Costa)
 -----BEGIN PGP SIGNATURE-----
 
 iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmmDr5ASHHJqd0Byand5
 c29ja2kubmV0AAoJEO5fvZ0v1OO1Q8oH/0KRqdidHzesIQl6gd5WSS/sWdxODRUt
 R9dEGQQ6LXCY0z05RAq29HZQf618fYuRFX4PSrtyCvrcRJK7MJKuzK55MRq0MC3c
 c/2pL1PdpHexjLXUP9pcoxrYjetsr7SnD6Y0M3JfOPg1E/bG8sp1DlnE8cdqrL0W
 lrdB2cEGewT2SVkNhCIQ2n6bwfQwmLlfQl1vXTM8BA7xCjoslePUJlRphAFVAt/J
 5fQxSOH0eSxK5PYQFUDM2D2J3uMAN0pFb6eIjwVYYqjABqV//BPl99Rv2W3ElJq7
 K/SICRWlvzyINCgF15QAUtQHWdINxSb0GzovECVxODHOv0N4mKHdpNU=
 =QlVe
 -----END PGP SIGNATURE-----

Merge tag 'pm-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "By the number of commits, cpufreq is the leading party (again) and the
  most visible change there is the removal of the omap-cpufreq driver
  that has not been used for a long time (good riddance). There are also
  quite a few changes in the cppc_cpufreq driver, mostly related to
  fixing its frequency invariance engine in the case when the CPPC
  registers used by it are not in PCC. In addition to that, support for
  AM62L3 is added to the ti-cpufreq driver and the cpufreq-dt-platdev
  list is updated for some platforms. The remaining cpufreq changes are
  assorted fixes and cleanups.

  Next up is cpuidle and the changes there are dominated by intel_idle
  driver updates, mostly related to the new command line facility
  allowing users to adjust the list of C-states used by the driver.
  There are also a few updates of cpuidle governors, including two menu
  governor fixes and some refinements of the teo governor, and a
  MAINTAINERS update adding Christian Loehle as a cpuidle reviewer.
  [Thanks for stepping up Christian!]

  The most significant update related to system suspend and hibernation
  is the one to stop freezing the PM runtime workqueue during system PM
  transitions which allows some deadlocks to be avoided. There is also a
  fix for possible concurrent bit field updates in the core device
  suspend code and a few other minor fixes.

  Apart from the above, several drivers are updated to discard the
  return value of pm_runtime_put() which is going to be converted to a
  void function as soon as everybody stops using its return value, PL4
  support for Ice Lake is added to the Intel RAPL power capping driver,
  and there are assorted cleanups, documentation fixes, and some
  cpupower utility improvements.

  Specifics:

   - Remove the unused omap-cpufreq driver (Andreas Kemnade)

   - Optimize error handling code in cpufreq_boost_trigger_state() and
     make cpufreq_boost_trigger_state() return -EOPNOTSUPP if no policy
     supports boost (Lifeng Zheng)

   - Update cpufreq-dt-platdev list for tegra, qcom, TI (Aaron Kling,
     Dhruva Gole, and Konrad Dybcio)

   - Minor improvements to the cpufreq and cpumask rust implementation
     (Alexandre Courbot, Alice Ryhl, Tamir Duberstein, and Yilin Chen)

   - Add support for AM62L3 SoC to the ti-cpufreq driver (Dhruva Gole)

   - Update arch_freq_scale in the CPPC cpufreq driver's frequency
     invariance engine (FIE) in scheduler ticks if the related CPPC
     registers are not in PCC (Jie Zhan)

   - Assorted minor cleanups and improvements in ARM cpufreq drivers
     (Juan Martinez, Felix Gu, Luca Weiss, and Sergey Shtylyov)

   - Add generic helpers for sysfs show/store to cppc_cpufreq (Sumit
     Gupta)

   - Make the scaling_setspeed cpufreq sysfs attribute return the actual
     requested frequency to avoid confusion (Pengjie Zhang)

   - Simplify the idle CPU time granularity test in the ondemand cpufreq
     governor (Frederic Weisbecker)

   - Enable asym capacity in intel_pstate only when CPU SMT is not
     possible (Yaxiong Tian)

   - Update the description of rate_limit_us default value in cpufreq
     documentation (Yaxiong Tian)

   - Add a command line option to adjust the C-states table in the
     intel_idle driver, remove the 'preferred_cstates' module parameter
     from it, add C-states validation to it and clean it up (Artem
     Bityutskiy)

   - Make the menu cpuidle governor always check the time till the
     closest timer event when the scheduler tick has been stopped to
     prevent it from mistakenly selecting the deepest available idle
     state (Rafael Wysocki)

   - Update the teo cpuidle governor to avoid making suboptimal
     decisions in certain corner cases and generally improve idle state
     selection accuracy (Rafael Wysocki)

   - Remove an unlikely() annotation on the early-return condition in
     menu_select() that leads to branch misprediction 100% of the time
     on systems with only 1 idle state enabled, like ARM64 servers
     (Breno Leitao)

   - Add Christian Loehle to MAINTAINERS as a cpuidle reviewer
     (Christian Loehle)

   - Stop flagging the PM runtime workqueue as freezable to avoid system
     suspend and resume deadlocks in subsystems that assume asynchronous
     runtime PM to work during system-wide PM transitions (Rafael
     Wysocki)

   - Drop redundant NULL pointer checks before acomp_request_free() from
     the hibernation code handling image saving (Rafael Wysocki)

   - Update wakeup_sources_walk_start() to handle empty lists of wakeup
     sources as appropriate (Samuel Wu)

   - Make dev_pm_clear_wake_irq() check the power.wakeirq value under
     power.lock to avoid race conditions (Gui-Dong Han)

   - Avoid bit field races related to power.work_in_progress in the core
     device suspend code (Xuewen Yan)

   - Make several drivers discard pm_runtime_put() return value in
     preparation for converting that function to a void one (Rafael
     Wysocki)

   - Add PL4 support for Ice Lake to the Intel RAPL power capping driver
     (Daniel Tang)

   - Replace sprintf() with sysfs_emit() in power capping sysfs show
     functions (Sumeet Pawnikar)

   - Make dev_pm_opp_get_level() return value match the documentation
     after a previous update of the latter (Aleks Todorov)

   - Use scoped for each OF child loop in the OPP code (Krzysztof
     Kozlowski)

   - Fix a bug in an example code snippet and correct typos in the
     energy model management documentation (Patrick Little)

   - Fix miscellaneous problems in cpupower (Kaushlendra Kumar):
      * idle_monitor: Fix incorrect value logged after stop
      * Fix inverted APERF capability check
      * Use strcspn() to strip trailing newline
      * Reset errno before strtoull()
      * Show C0 in idle-info dump

   - Improve cpupower installation procedure by making the systemd step
     optional and allowing users to disable the installation of
     systemd's unit file (João Marcos Costa)"

* tag 'pm-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
  PM: sleep: core: Avoid bit field races related to work_in_progress
  PM: sleep: wakeirq: harden dev_pm_clear_wake_irq() against races
  cpufreq: Documentation: Update description of rate_limit_us default value
  cpufreq: intel_pstate: Enable asym capacity only when CPU SMT is not possible
  PM: wakeup: Handle empty list in wakeup_sources_walk_start()
  PM: EM: Documentation: Fix bug in example code snippet
  Documentation: Fix typos in energy model documentation
  cpuidle: governors: teo: Refine intercepts-based idle state lookup
  cpuidle: governors: teo: Adjust the classification of wakeup events
  cpufreq: ondemand: Simplify idle cputime granularity test
  cpufreq: userspace: make scaling_setspeed return the actual requested frequency
  PM: hibernate: Drop NULL pointer checks before acomp_request_free()
  cpufreq: CPPC: Add generic helpers for sysfs show/store
  cpufreq: scmi: Fix device_node reference leak in scmi_cpu_domain_id()
  cpufreq: ti-cpufreq: add support for AM62L3 SoC
  cpufreq: dt-platdev: Add ti,am62l3 to blocklist
  cpufreq/amd-pstate: Add comment explaining nominal_perf usage for performance policy
  cpufreq: scmi: correct SCMI explanation
  cpufreq: dt-platdev: Block the driver from probing on more QC platforms
  rust: cpumask: rename methods of Cpumask for clarity and consistency
  ...
2026-02-09 19:00:42 -08:00
Dmitry Baryshkov
8ad0f7d2e6 drm: bridge: anx7625: implement message sending
Swapping the data role requires sending the message to the other USB-C
side. Implement sending these messages through the OCM. The code is
largely based on the anx7411.c USB-C driver.

Reviewed-by: Xin Ji <xji@analogixsemi.com>
Link: https://patch.msgid.link/20260121-anx7625-typec-v2-3-d14f31256a17@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-02-07 12:38:38 +02:00
Dmitry Baryshkov
f81455b2d3 drm: bridge: anx7625: implement minimal Type-C support
ANX7625 can be used as a USB-C controller, handling USB and DP data
streams. Provide minimal Type-C support necessary for ANX7625 to
register the Type-C port device and properly respond to data / power
role events from the Type-C partner.

While ANX7625 provides TCPCI interface, using it would circumvent the
on-chip running firmware. Analogix recommended using the higher-level
interface instead of TCPCI.

Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260121-anx7625-typec-v2-2-d14f31256a17@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2026-02-07 12:38:37 +02:00
Dave Airlie
3c5ab2407a Several fixes for amdxdna around PM handling, error reporting and
memory safety, a compilation fix for ilitek-ili9882t, a NULL pointer
 dereference fix for imx8qxp-pixel-combiner and several PTE fixes for
 nouveau
 -----BEGIN PGP SIGNATURE-----
 
 iJUEABMJAB0WIQTkHFbLp4ejekA/qfgnX84Zoj2+dgUCaYR9UwAKCRAnX84Zoj2+
 dvScAX9KvMXTtSmkNP3+IBFADXSH4XW9O867wMBmCMUDnPwC67CA7bXPpO0chj84
 /moUBj4BfA7MQ81eHeiEYrTAKiX7OLrhJ8jnwMRcUVJFL2lcLRB4Y86lBcB1Xbkv
 IRzgp6+a9g==
 =DZDH
 -----END PGP SIGNATURE-----

Merge tag 'drm-misc-next-fixes-2026-02-05' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next

Several fixes for amdxdna around PM handling, error reporting and
memory safety, a compilation fix for ilitek-ili9882t, a NULL pointer
dereference fix for imx8qxp-pixel-combiner and several PTE fixes for
nouveau

Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maxime Ripard <mripard@redhat.com>
Link: https://patch.msgid.link/20260205-refreshing-natural-vole-4c73af@houat
2026-02-06 12:52:15 +10:00
Thomas Zimmermann
2bebc88d5e Merge drm/drm-next into drm-misc-next
Backmerging to get bug fixes from v6.19-rc7.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2026-02-05 10:33:06 +01:00
Icenowy Zheng
96f30ee0fb drm/bridge: add a driver for T-Head TH1520 HDMI controller
T-Head TH1520 SoC contains a Synopsys DesignWare HDMI controller (paired
with DesignWare HDMI TX PHY Gen2) that takes the "DP" output from the
display controller.

Add a driver for this controller utilizing the common DesignWare HDMI
code in the kernel.

Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Tested-by: Han Gao <gaohan@iscas.ac.cn>
Tested-by: Michal Wilczynski <m.wilczynski@samsung.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260129023922.1527729-6-zhengxingda@iscas.ac.cn
2026-02-05 09:50:30 +01:00
Shengjiu Wang
40b24d9cdd drm/bridge: imx8mp-hdmi-pai: enable PM runtime
There is an audio channel shift issue with multi channel case - the
channel order is correct for the first run, but the channel order is
shifted for the second run. The fix method is to reset the PAI interface
at the end of playback.

The reset can be handled by PM runtime, so enable PM runtime.

Fixes: 0205fae632 ("drm/bridge: imx: add driver for HDMI TX Parallel Audio Interface")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20260130080910.3532724-1-shengjiu.wang@nxp.com
2026-02-05 16:16:45 +08:00