CNS3xxx chips have SDHCI-compatible SDIO/SD/MMC controller. This patch
adds the support using sdhci-cns3xxx driver.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
This patch adds PCIe support for CNS3xxx-based boards. The support
was tested with a directly attached SKY2 NIC, and EHCI USB controller
behind the PLX PEX8112 P2P bridge (to make sure that type1 cfg cycles
work as expected).
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Before it isn't too late let's switch to IO memory accessors.
This patch converts all current _REG users and _REG definitions.
There should be no functional changes.
Suggested-by: Ben Dooks <ben-linux@fluff.org>
Suggested-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Reading the ELP_CTRL register with sdio_readb causes problems because
hardware seems to be performing a write using stuff bits in the request
(those bits contain write data in write request). This indicates that it
actually expects RAW (read after write) type of request, so perform that
when reading ELP_CTRL instead. Also cache last written value so we know
what to write when doing RAW request.
Because of the above it was not possible to wake the chip from ELP power
saving mode, PM had to be disabled to have the driver usable in SDIO
mode. After this patch PM is functional.
For backporting to 2.6.34 or earlier, this patch depends on
6c1f716e81, which adds the
required SDIO funcion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a whole bunch of kernel-doc warnings
and errors that crop up when running it on
mac80211 and cfg80211; the latter isn't
normally done so lots of bit-rot happened.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a window for ieee80211_ifa_changed() to get called whilst the
managed mode mutex has not been initialized when opening and stopping the
interface. Currently this causes a kernel BUG like the following:
[ 132.460013] kernel BUG at /home/wifi/iwlwifi-2.6/net/mac80211/main.c:380!
[ 132.460013] invalid opcode: 0000 [#1] SMP
The mutex is initialized during open(), hence once netif_running() is true,
the mutex should be valid. Fix by adding a netif_running() check to the
function.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath5k_hw_set_antenna_mode() always writes the default antenna register
and is called at the end of reset, there is no need to separately save and
restore the default antenna.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Collect all pieces concering the antenna switch table into one function.
Previously it was split up between ath5k_hw_reset() and
ath5k_hw_commit_eeprom_settings().
Also we need to set the antenna switch table when ath5k_hw_set_antenna_mode()
is called manually (by "iw phy0 antenna set", for example).
I'm not sure if we need to set the switchtable at the same place in
ath5k_hw_reset() as it was before - it is set later thru
ath5k_hw_set_antenna_mode() anyways - but i leave it there to avoid
problems(?).
Plus print switchtable registers in the debugfs file.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
#define AR5K_PHY_RESTART_DIV_GC 0x001c0000
is 3 bit wide.
The previous values of 0xc and 0x8 are 4bit wide and bigger than the mask.
Writing 0 and 1 to AR5K_PHY_RESTART_DIV_GC is consistent with the comments and
initvals we have in the HAL.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the libertas driver incorrectly reporting that Wake-on-LAN
is not supported if Wake-on-LAN is currently disabled.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently dirty two cache lines in struct xt_rateest, this hurts SMP
performance.
This patch moves lock/bstats/rstats at beginning of structure so that
they share a single cache line.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If we fail to submit URBs we should take touchpad out of wellsping
mode.
Signed-off-by: Luo Jinghua <sunmoon1997@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let's perform be16_to_cpu() conversions once for each received packet,
and then use cached values. Makes code a little bit easier to follow.
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With no word size given in the users platform data, a generic spi host
controller driver will assume a default word size of eight bit. This
causes transmission to be performed bytewise, which will fail on little
endian machines for sure. Failure on big endian depends on usage
of slave select to mark word boundaries.
Anyway, ad7877 is specified to work with 16 bit per word, so
unconditionally set the word size accordingly. Flag an error where 16
bit per word is not available.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oliver Schneidewind <osw@emlix.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- dev_get_by_flags() changed to dev_get_by_flags_rcu()
- ipv6_sock_ac_join() dont touch dev & idev refcounts
- ipv6_sock_ac_drop() dont touch dev & idev refcounts
- ipv6_sock_ac_close() dont touch dev & idev refcounts
- ipv6_dev_ac_dec() dount touch idev refcount
- ipv6_chk_acast_addr() dont touch idev refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So when we added output polling, we'd suddenly use this code more often, and the fact that it always takes over crtc2 and messes with it during probing isn't what we really want to be happening. A more complete fix would to change it to use whatever crtc was free at the time, but for now lets stay simple and just don't poll if crtc2 is already in use.
Although a more correct fix was found I suspect we should do this as well, until we get a chance to readdres the tv out polling issues.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We really don't want to be polling tv-out but since we weren't forcing the
i2c lines to invalid (tv-out has no DDC), we were adding tv connectors to the
polling setup and this was causing blinking on secondary displays.
This fixes the regression Torsten reported.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function.
[ Fix build with CONFIG_IP_ROUTE_VERBOSE disabled. -DaveM ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Straightforward conversion to RCU.
One rwlock becomes a spinlock, and is static.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use call_rcu rather than synchronize_rcu.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dcb->i2c[] has DCB_MAX_NUM_I2C_ENTRIES entries.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If "gpio->line" is 32 then "nv50_gpio_reg[gpio->line >> 3]" reads past the
end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On cards where there's a specific BAR for PRAMIN, we used to try and fall
back to the "legacy" aperture within the mmio BAR.
This is doomed to cause problems, so lets just fail completely as there's
obviously something else very wrong anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It appears version 0x21 'U' and 'd' tables require us to take the SOR link
into account when selecting the appropriate table for a particular output.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As Ingo pointed out in a separate patch, we should be using __ASSEMBLY__.
Make that the case in pgtable headers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
LKML-Reference: <20100605114042.35ac69c1@dev.queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* git://git.infradead.org/~dwmw2/mtd-2.6.35:
jffs2: update ctime when changing the file's permission by setfacl
jffs2: Fix NFS race by using insert_inode_locked()
jffs2: Fix in-core inode leaks on error paths
mtd: Fix NAND submenu
mtd/r852: update card detect early.
mtd/r852: Fixes in case of DMA timeout
mtd/r852: register IRQ as last step
drivers/mtd: Use memdup_user
docbook: make mtd nand module init static
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: redo stopping DMA engines on empty ports
sata_sil24: fix kernel panic on ARM caused by unaligned access in sata_sil24
ahci: add pci quirk for JMB362
sata_via: explain the magic fix
This fixes FDO bug #28375, it's kind of regression, so quite important to have
it for .35.
V2: Fix on RV770+ as well. All other chipsets have only one clock mode per
state.
V3: I'm out of luck today. Grepped for voltage in r*.c and missed evergreen.
agd5f: rebased
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
track the current voltage level and avoid setting it
if the requested voltage is already set.
v2: check voltage type before checking current voltage
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vddc value in the power tables is not an actual voltage
like on discrete r6xx/r7xx/evergreen systems, but instead has
a symbolic meaning (e.g., NONE, LOW, HIGH, etc.). See atombios.h
Most RS780/RS880 vbioses don't have a SetVoltage table anyway,
so it shouldn't be doing anything to the hardware at the moment.
I need to figure out how voltage is supposed to work on the newer
IGPs; until then, disable it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile. The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state. Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- don't rest the power state in pm_init()
We already boot up to the default power state. Note this
patch relies on:
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
To make sure the default power state matches the boot up state.
- In the pm resume path asic init will have set the power state
back to the default so reset the tracking state values.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable accel in the ddx. However,
due to a bug in older versions of the ddx, it relies
on accel being disabled in order to load properly on
evergreen chips. To maintain compatility, we add a new
get accel param and call that from the ddx. The old one
always returns false for evergreen cards.
[this fixes a regression with older userspaces on newer kernels].
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to/from_user() returns the number of bytes remaining to be copied
but we want to return a negative error code here. This gets returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_from_user() returns the number of bytes left to be copied but we
want to return a negative error code here. This is in the ioctl handler
so the error code get returned to userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
using DRM_ERROR, results in people blaming the drm code for the oops, and
not looking at the oops.
(sadly yes I've gotten reports).
Signed-off-by: Dave Airlie <airlied@redhat.com>
PM attemps to unmap objects that aren't actually mapped into userspace ever,
so just don't bother unmapping them at this point, since all you are doing
is nothing. We should be making sure all access to these objects are locked in
kernel space instead. In theory the VRAM gart table is already done, and both
the shaders and stolen vga memory blocks are never accessed at runtime.
fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16127
Reported-by: Jure Repnic <jlp.bugs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.
I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(regression fix since fbdev/kms rework).
My fb rework didn't remember about the 84/65s.
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At some point this was exposed (not sure how),
linux-2.6/arch/arm/mach-msm/dma.c:92: error: field 'complete' has incomplete type
linux-2.6/arch/arm/mach-msm/dma.c: In function 'dmov_exec_cmdptr_complete_func':
linux-2.6/arch/arm/mach-msm/dma.c:108: error: implicit declaration of function 'complete'
linux-2.6/arch/arm/mach-msm/dma.c: In function 'msm_dmov_exec_cmd':
linux-2.6/arch/arm/mach-msm/dma.c:120: error: implicit declaration of function 'init_completion'
linux-2.6/arch/arm/mach-msm/dma.c:123: error: implicit declaration of function 'wait_for_completion'
and the fix is just to add the header.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Save/restore MISC_ENABLE register on suspend/resume.
This fixes OOPS (invalid opcode) on resume from STR on Asus P4P800-VM,
which wakes up with MWAIT disabled.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15385
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 96d60303fd (ahci: Turn off DMA engines when there's no device)
implemented stopping DMA engines on empty ports but it used single
sampling of status registers to determine device presence which led to
disabling of DMA engines on occupied ports. Do it after all EH
actions are complete using device presence state determined by EH.
This avoids spurious disabling of DMA engines and simplifies the code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>