Following changes have been added to enable the adapter to work in
NIC partitioning mode where multiple PCI functions of an adapter port can
be configured to work as NIC functions. The first function that is enumerated on
the PCI bus assumes the role of management function which, besides being able
to do all the NIC functionality, can configure other NIC partitions. Other NIC
functions can be configured as privileged or non privileged functions.
Privileged function can not configure other NIC functions but can do all the
NIC functionality including any firmware initialization, chip reset etc. Non
privileged functions can do only basic IO. For chip reset etc, it depends on the
privilege or management function.
1. Added code to determine PCI function number independent of kernel API.
2. Added Driver - FW version 2.0 support.
3. Changed producer and consumer register offset calculation.
4. Added management and privileged operation modes for npar functions. A module
parameter has been added to control it.
5. Added support for configuring the eswitch in the adapter.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_errors is defined as 'bad packets received', but we are currently
including various overflow errors as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insert a structure at the start of the shared page that
tracks the dma mapping refcnt. DMA into the next cache
line of the (shared) page (plus EFX_PAGE_IP_ALIGN).
When recycling a page, check the page refcnt. If the
page is otherwise unused, then resurrect the other
receive buffer that previously referenced the page.
Be careful not to overflow the receive ring, since we
can now resurrect n receive buffers in a row.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cut-through design of the receive path means that packets that
fail to match the appropriate MAC filter are not discarded at the MAC
but are flagged in the completion event as 'to be discarded'. On
networks with heavy multicast traffic, this can account for a
significant proportion of received packets, so it is worthwhile to
recycle the buffer immediately in this case rather than freeing it
and then reallocating it shortly after.
The only complication here is dealing with a page shared
between two receive buffers. In that case, we need to be
careful to free the dma mapping when both buffers have
been free'd by the kernel. This means that we can only
recycle such a page if both receive buffers are discarded.
Unfortunately, in an environment with 1500mtu,
rx_alloc_method=PAGE, and a mixture of discarded and
not-discarded frames hitting the same receive queue,
buffer recycling won't always be possible.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Pull the loop handling into efx_init_rx_buffers_(skb|page)
- Remove rx_queue->buf_page, and associated clean up code
- Remove unmap_addr, since unmap_addr is trivially calculable
This will allow us to recycle discarded buffers directly
from efx_rx_packet(), since will never be in the middle of
splitting a page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that efx_fast_push_rx_descriptors() must only run
from efx_process_channel() [NAPI], or when napi_disable()
has been executed.
Reimplement the slow fill by sending an event to the
channel, so that NAPI runs, and hanging the subsequent
fast fill off the event handler. Replace the sfc_refill
workqueue and delayed work items with a timer. We do
not need to stop this timer in efx_flush_all() because
it's safe to send the event always; receiving it will
be delayed until NAPI is restarted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Formerly, efx_test_eventq_irq() assumed it was the only user of
driver generated events. Allow it to interoperate with other users.
We can create more than 16 channels, so align event codes with
a multiple of 256 not 16.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that some phys (such as the qt2025c) can
do down-up-down-up transitions, presumably as pcs block lock
settles down.
The loopback selftest will start sending data immediately
after the link comes up. Work around this by waiting for
the link state to stay up for two consecutive polls, rather
than one.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the ethtool code paths keep them in sync, but we need
to ensure they are sync'd at start of day. Matches the sft9001
driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions a PHY may backpressure Falcon B0
in such a way that flushes timeout. In normal circumstances
the phy poller would fix the PHY, and the flush could complete.
But efx_nic_flush_queues() is always called after efx_stop_all(),
so the poller has been stopped. Even if this weren't the case,
how long would we have to wait for the poller to fix this? And
several callers of efx_nic_flush_queues() are about to reset
the device anyway - so we don't need to do anything.
Work around this bug by scheduling a reset. Ensure that the
MAC is never rewired back into the datapath before the reset
runs (we already ignore all rx events anyway).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_pm_freeze() sets efx->state = STATE_FINI, which means
efx_reset_work() will abort any scheduled resets.
efx_pm_thaw() should reschedule efx_reset_work() again,
since a freeze/thaw will not have reset the hardware.
This bug was spotted by inspection - there is no real world example of
this happening.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of its members are constant capabilities, not configuration. The
new name is also consistent with the name of the pointer to it in
struct efx_nic and the names of structures used by other PHY drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping pr_fmt to the KBUILD_MODNAME prefix seems to be the trendy
thing to do these days, so just do that instead of manually tidying
up the stragglers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
MMC0/SDHI1 (CN7) can be selected by dip switch.
And card voltage can be selected by jumper pin.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the irq numbers for MMCIF
to make use of evt2irq().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on the sh_tmu change in 66f49121ff
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since commit 98962465ed ("nohz: Prevent
clocksource wrapping during idle"), the CPU of an R2D board never goes
to idle. This commit assumes that mult and shift are assigned before
the clocksource is registered. As a consequence the safe maximum sleep
time is negative and the CPU never goes into idle.
This patch fixes the problem by moving mult and shift initialization
from sh_tmu_clocksource_enable() to sh_tmu_register_clocksource().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a sporadic oops at boot on G5 Power Macs. The table_end
variable has the address of the last byte of the table. Adding on
PAGE_SIZE means we flush too much, and if the page after the table
is not mapped for any reason, the kernel will oops. Instead we add
on 1 because flush_dcache_range() interprets its second argument as
the first byte past the range to be flushed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PWRficient platform work is definitely in maintenance mode these
days, update MAINTAINERS file to reflect reality.
Website is long gone as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix smatch warning: warning: constant 0x800000000 is so big it is long
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
emulate_step() in kprobe_handler() would've already determined if the
probed instruction can be emulated. We single-step in hardware only if
the instruction couldn't be emulated. resume_execution() therefore is
superfluous -- all we need is to fix up the instruction pointer after
single-stepping.
Thanks to Paul Mackerras for catching this.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes bug introduced by commit 61c7a080a5
(of: Always use 'struct device.of_node' to get device node pointer)
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the follwing warning introduced by commit
067fb2f648 ("Input: ads7846 - return error on
regulator_get() failure"):
drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Percpu initialization happens now after booting the cores on the
machine and this causes them all to be displayed as belonging to
node 0:
Jun 8 05:57:21 kepek kernel: [ 0.106999] Booting Node 0,
Processors #1#2#3#4#5#6#7#8#9#10#11#12#13#14#15#16#17#18#19#20#21#22#23 Ok.
Use early_cpu_to_node() to get the correct node of each core
instead.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mike Travis <travis@sgi.com>
LKML-Reference: <20100601190455.GA14237@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
urquell only provides PIO in the PCI case, while the x3proto board never
had a working PCIe controller, so it can simply disable it outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends some of the existing special casing for HAS_IOPORT
platforms and gets it to the point where platforms can begin to
conditionally select it.
The major changes here are that the PIO routines themselves go away
completely, including all of the machvec port mapping wrappers. With this
in place it's possible for any non-machvec abusing platform to disable
PIO completely. At present this is left as an opt-in until the abusers
are the odd ones out instead of the majority.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
r8a66597-hcd is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
r8a66597-udc is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
m66592-udc is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
1) Use msecs_to_jiffies() instead of calculating by hand.
2) Call cancel_delayed_work_sync() instead of cancel_delayed_work()
followed by a separate flush_workqueue().
3) Remove the "tsc->wq = 0;" Sparse complains about that because
tsc->wq is a pointer, not an int. It's not needed because we just
free the pointer anyway.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We were setting f_namelen in kstatfs to PATH_MAX instead of NAME_MAX.
That disagrees with ceph_lookup behavior (which checks against NAME_MAX),
and also makes the pjd posix test suite spit out ugly errors because with
can't clean up its temporary files.
Signed-off-by: Sage Weil <sage@newdream.net>
We misused list_move_tail() to order the dentry in d_subdirs.
This will screw up the d_subdirs order.
This bug can be reliably reproduced by:
1. mount ceph fs.
2. on ceph fs, git clone git://ceph.newdream.net/git/ceph.git
3. Run autogen.sh in ceph directory.
(Note: Errors only occur at the first time you run autogen.sh.)
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The conversion of write_inode_now calls to commit_metadata in commit
f501912a35 missed out the call in nfsd_setattr.
But without this conversion we can't guarantee that a SETATTR request
has actually been commited to disk with XFS, which causes a regression
from 2.6.32 (only for NFSv2, but anyway).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>