This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Furthermore, the following mode parameter can be defined:
clk: External oscillator clock frequency (default=16000000 [16 MHz])
cir: CPU interface register (default=0x40 [CPU_DSC])
ocr, Bus configuration register (default=0x00)
cor, Clockout register (default=0x00)
Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some basic regulator support for the power pins, as needed
by the ST-Ericsson Snowball platform that powers up the SMSC911
chip using an external regulator.
Platforms that use regulators and the smsc911x and have no defined
regulator for the smsc911x and claim complete regulator
constraints with no dummy regulators will need to provide it, for
example using a fixed voltage regulator. It appears that this may
affect (apart from Ux500 Snowball) possibly these archs/machines
that from some grep:s appear to define both CONFIG_SMSC911X and
CONFIG_REGULATOR:
- ARM Freescale mx3 and OMAP 2 plus, Raumfeld machines
- Blackfin
- Super-H
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is currently not supported on x86_64 systems because the
"isa_driver" interface is used (CONFIG_ISA=y). To overcome this
limitation, the driver is converted to a platform driver, similar to
the serial 8250 driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7dc00c82 added a 'notify' parameter for vif_delete() to
distinguish whether to unregister the device.
When notify=1 means we does not need to unregister the device,
so calling unregister_netdevice_many is useless.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compiler warnings: "comparison is always
false due to limited range of data type" by using "0xff" instead
of "-1" for unsigned values.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change function rcu_dereference to rcu_dereference_bh to avoid warning
[ INFO: suspicious RCU usage. ]
-------------------------------
net/core/dev.c:2459 suspicious rcu_dereference_check() usage!
because we are locking with
rcu_read_lock_bh();
in function dev_queue_xmit(struct sk_buff *skb)
Signed-off-by: Igor Maravic <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Update comments describing device power management callbacks
PM / Sleep: Update documentation related to system wakeup
PM / Runtime: Make documentation follow the new behavior of irq_safe
PM / Sleep: Correct inaccurate information in devices.txt
PM / Domains: Document how PM domains are used by the PM core
PM / Hibernate: Do not leak memory in error/test code paths
A recent fix to the the NetLabel code caused build problem with
configurations that did not have IPv6 enabled; see below:
netlabel_kapi.c: In function 'netlbl_cfg_unlbl_map_add':
netlabel_kapi.c:165:4:
error: implicit declaration of function 'netlbl_af6list_add'
This patch fixes this problem by making the IPv6 specific code conditional
on the IPv6 configuration flags as we done in the rest of NetLabel and the
network stack as a whole. We have to move some variable declarations
around as a result so things may not be quite as pretty, but at least it
builds cleanly now.
Some additional IPv6 conditionals were added to the NetLabel code as well
for the sake of consistency.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2c31e32b3 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This following can occur with ipoib when processing a multicast reponse:
BUG: soft lockup - CPU#0 stuck for 67s! [ib_mad1:982]
Modules linked in: ...
CPU 0:
Modules linked in: ...
Pid: 982, comm: ib_mad1 Not tainted 2.6.32-131.0.15.el6.x86_64 #1 ProLiant DL160 G5
RIP: 0010:[<ffffffff814ddb27>] [<ffffffff814ddb27>] _spin_unlock_irqrestore+0x17/0x20
RSP: 0018:ffff8802119ed860 EFLAGS: 00000246
0000000000000004 RBX: ffff8802119ed860 RCX: 000000000000a299
RDX: ffff88021086c700 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ffffffff8100bc8e R08: ffff880210ac229c R09: 0000000000000000
R10: ffff88021278aab8 R11: 0000000000000000 R12: ffff8802119ed860
R13: ffffffff8100be6e R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d4840 CR3: 0000000209aa5000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffffa032c247>] ? ipoib_mcast_send+0x157/0x480 [ib_ipoib]
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffffa03283d4>] ? ipoib_path_lookup+0x124/0x2d0 [ib_ipoib]
[<ffffffffa03286fc>] ? ipoib_start_xmit+0x17c/0x430 [ib_ipoib]
[<ffffffff8141e758>] ? dev_hard_start_xmit+0x2c8/0x3f0
[<ffffffff81439d0a>] ? sch_direct_xmit+0x15a/0x1c0
[<ffffffff81423098>] ? dev_queue_xmit+0x388/0x4d0
[<ffffffffa032d6b7>] ? ipoib_mcast_join_finish+0x2c7/0x510 [ib_ipoib]
[<ffffffffa032dab8>] ? ipoib_mcast_sendonly_join_complete+0x1b8/0x1f0 [ib_ipoib]
[<ffffffffa02a0946>] ? mcast_work_handler+0x1a6/0x710 [ib_sa]
[<ffffffffa015f01e>] ? ib_send_mad+0xfe/0x3c0 [ib_mad]
[<ffffffffa00f6c93>] ? ib_get_cached_lmc+0xa3/0xb0 [ib_core]
[<ffffffffa02a0f9b>] ? join_handler+0xeb/0x200 [ib_sa]
[<ffffffffa029e4fc>] ? ib_sa_mcmember_rec_callback+0x5c/0xa0 [ib_sa]
[<ffffffffa029e79c>] ? recv_handler+0x3c/0x70 [ib_sa]
[<ffffffffa01603a4>] ? ib_mad_completion_handler+0x844/0x9d0 [ib_mad]
[<ffffffffa015fb60>] ? ib_mad_completion_handler+0x0/0x9d0 [ib_mad]
[<ffffffff81088830>] ? worker_thread+0x170/0x2a0
[<ffffffff8108e160>] ? autoremove_wake_function+0x0/0x40
[<ffffffff810886c0>] ? worker_thread+0x0/0x2a0
[<ffffffff8108ddf6>] ? kthread+0x96/0xa0
[<ffffffff8100c1ca>] ? child_rip+0xa/0x20
Coinciding with stack trace is the following message:
ib0: ib_address_create failed
The code below in ipoib_mcast_join_finish() will note the above
failure in the address handle but otherwise continue:
ah = ipoib_create_ah(dev, priv->pd, &av);
if (!ah) {
ipoib_warn(priv, "ib_address_create failed\n");
} else {
The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():
if (!mcast->ah) {
if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
skb_queue_tail(&mcast->pkt_queue, skb);
else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.
There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.
The test that induced the failure is associated with a host SM on the
same server during a shutdown.
This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets. Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Reviewed-by: Gary Leshner <gary.leshner@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The check from commit 30c2235c is incomplete and cannot prevent
cases like key_len = 0x80000000 (INT_MAX + 1). In that case, the
left-hand side of the check (INT_MAX - key_len), which is unsigned,
becomes 0xffffffff (UINT_MAX) and bypasses the check.
However this shouldn't be a security issue. The function is called
from the following two code paths:
1) setsockopt()
2) sctp_auth_asoc_set_secret()
In case (1), sca_keylength is never going to exceed 65535 since it's
bounded by a u16 from the user API. As such, the key length will
never overflow.
In case (2), sca_keylength is computed based on the user key (1 short)
and 2 * key_vector (3 shorts) for a total of 7 * USHRT_MAX, which still
will not overflow.
In other words, this overflow check is not really necessary. Just
make it more correct.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actively manage the detection rate for microphones with WM8958, providing
improved power consumption and maximising the benefit from the hardware
debounce.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some users of regmap_update_bits() would like to be able to tell their
users if they actually did an update so provide a variant which also
returns a flag indicating if an update took place. We could return a
tristate in the return value of regmap_update_bits() but this makes the
API more cumbersome to use and doesn't fit with the general zero for
success idiom we have.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we don't have any active audio we can put the microphone biases into
bypass mode to save power at the expense of performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slub: avoid potential NULL dereference or corruption
slub: use irqsafe_cpu_cmpxchg for put_cpu_partial
slub: move discard_slab out of node lock
slub: use correct parameter to add a page to partial list tail
With Dmitry fsstress updates I've seen very reproducible crashes in
xfs_attr_shortform_remove because xfs_attr_shortform_bytesfit claims that
the attributes would not fit inline into the inode after removing an
attribute. It turns out that we were operating on an inode with lots
of delalloc extents, and thus an if_bytes values for the data fork that
is larger than biggest possible on-disk storage for it which utterly
confuses the code near the end of xfs_attr_shortform_bytesfit.
Fix this by always allowing the current attribute fork, like we already
do for the attr1 format, given that delalloc conversion will take care
for moving either the data or attribute area out of line if it doesn't
fit at that point - or making the point moot by merging extents at this
point.
Also document the function better, and clean up some loose bits.
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of using a custom flow dissector, use skb_flow_dissect() and
benefit from tunnelling support.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a custom flow dissector, use skb_flow_dissect() and
benefit from tunnelling support.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sendmsg() uses select_size() helper to choose skb head size when a
new skb must be allocated.
If GSO is enabled for the socket, current strategy is to force all
payload data to be outside of headroom, in PAGE fragments.
This strategy is not welcome for small packets, wasting memory.
Experiments show that best results are obtained when using 2048 bytes
for skb head (This includes the skb overhead and various headers)
This patch provides better len/truesize ratios for packets sent to
loopback device, and reduce memory needs for in-flight loopback packets,
particularly on arches with big pages.
If a sender sends many 1-byte packets to an unresponsive application,
receiver rmem_alloc will grow faster and will stop queuing these packets
sooner, or will collapse its receive queue to free excess memory.
netperf -t TCP_RR results are improved by ~4 %, and many workloads are
improved as well (tbench, mysql...)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le lundi 28 novembre 2011 à 19:06 -0500, David Miller a écrit :
> From: Dimitris Michailidis <dm@chelsio.com>
> Date: Mon, 28 Nov 2011 08:25:39 -0800
>
> >> +bool skb_flow_dissect(const struct sk_buff *skb, struct flow_keys
> >> *flow)
> >> +{
> >> + int poff, nhoff = skb_network_offset(skb);
> >> + u8 ip_proto;
> >> + u16 proto = skb->protocol;
> >
> > __be16 instead of u16 for proto?
>
> I'll take care of this when I apply these patches.
( CC trimmed )
Thanks David !
Here is a small patch to use one 64bit load/store on x86_64 instead of
two 32bit load/stores.
[PATCH net-next] flow_dissector: use a 64bit load/store
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flow_keys (src,dst) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are doing synchronous inode reclaim we block the VM from making
progress in memory reclaim. So if we encouter a flush locked inode
promote it in the delwri list and wake up xfsbufd to write it out now.
Without this we can get hangs of up to 30 seconds during workloads hitting
synchronous inode reclaim.
The scheme is copied from what we do for dquot reclaims.
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Ben Myers <bpm@sgi.com>
Changes to sfc to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to bnx2x to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to tg3 to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to forcedeth to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to e1000e to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Networking stack support for byte queue limits, uses dynamic queue
limits library. Byte queue limits are maintained per transmit queue,
and a dql structure has been added to netdev_queue structure for this
purpose.
Configuration of bql is in the tx-<n> sysfs directory for the queue
under the byte_queue_limits directory. Configuration includes:
limit_min, bql minimum limit
limit_max, bql maximum limit
hold_time, bql slack hold time
Also under the directory are:
limit, current byte limit
inflight, current number of bytes on the queue
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the xps specific parts in netdev_queue_release into
its own function which netdev_queue_release can call. This allows
netdev_queue_release to be more generic (for adding new attributes
to tx queues).
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add interfaces for drivers to call for recording number of packets and
bytes at send time and transmit completion. Also, added a function to
"reset" a queue. These will be used by Byte Queue Limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create separate queue state flags so that either the stack or drivers
can turn on XOFF. Added a set of functions used in the stack to determine
if a queue is really stopped (either by stack or driver)
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of dynamic queue limits (dql). This is a libary which
allows a queue limit to be dynamically managed. The goal of dql is
to set the queue limit, number of objects to the queue, to be minimized
without allowing the queue to be starved.
dql would be used with a queue which has these properties:
1) Objects are queued up to some limit which can be expressed as a
count of objects.
2) Periodically a completion process executes which retires consumed
objects.
3) Starvation occurs when limit has been reached, all queued data has
actually been consumed but completion processing has not yet run,
so queuing new data is blocked.
4) Minimizing the amount of queued data is desirable.
A canonical example of such a queue would be a NIC HW transmit queue.
The queue limit is dynamic, it will increase or decrease over time
depending on the workload. The queue limit is recalculated each time
completion processing is done. Increases occur when the queue is
starved and can exponentially increase over successive intervals.
Decreases occur when more data is being maintained in the queue than
needed to prevent starvation. The number of extra objects, or "slack",
is measured over successive intervals, and to avoid hysteresis the
limit is only reduced by the miminum slack seen over a configurable
time period.
dql API provides routines to manage the queue:
- dql_init is called to intialize the dql structure
- dql_reset is called to reset dynamic values
- dql_queued called when objects are being enqueued
- dql_avail returns availability in the queue
- dql_completed is called when objects have be consumed in the queue
Configuration consists of:
- max_limit, maximum limit
- min_limit, minimum limit
- slack_hold_time, time to measure instances of slack before reducing
queue limit
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always store the register address as __iomem but pass it around as a
plain void * which upsets sparse.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure SYSCLK is enabled while running accessory detection on WM8958.
It is always required so there is no sense in requiring machine drivers
to individually do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To obtain a list of available tests:
[root@emilia linux]# perf test list
1: vmlinux symtab matches kallsyms
2: detect open syscall event
3: detect open syscall event on all cpus
4: read samples using the mmap interface
5: parse events tests
[root@emilia linux]#
To list just a subset:
[root@emilia linux]# perf test list syscall
2: detect open syscall event
3: detect open syscall event on all cpus
[root@emilia linux]#
To run a subset:
[root@emilia linux]# perf test detect
2: detect open syscall event: Ok
3: detect open syscall event on all cpus: Ok
[root@emilia linux]#
Specific tests can be chosen by number:
[root@emilia linux]# perf test 1 3 parse
1: vmlinux symtab matches kallsyms: Ok
3: detect open syscall event on all cpus: Ok
5: parse events tests: Ok
[root@emilia linux]#
Now to write more tests!
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-nqec2145qfxdgimux28aw7v8@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
this will allow to use gpio_is_valid
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
