Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
the last entry from being omitted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We've been hitting BUG()'s in btrfs_cont_expand and btrfs_fallocate and anywhere
else that calls btrfs_get_extent while running xfstests 13 in a loop. This is
because fiemap is calling btrfs_get_extent with non-sectorsize aligned offsets,
which will end up adding mappings that are not sectorsize aligned, which will
cause problems in some cases for subsequent calls to btrfs_get_extent for
similar areas that are sectorsize aligned. With this patch I ran xfstests 13 in
a loop for a couple of hours and didn't hit the problem that I could previously
hit in at most 20 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
When doing the io_ctl helpers to clean up the free space cache stuff I stopped
using our normal prepare_pages stuff, which means I of course forgot to do
things like set the pages extent mapped, which will cause us all sorts of
wonderful propblems. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We've been hitting panics when running xfstest 13 in a loop for long periods of
time. And actually this problem has always existed so we've been hitting these
things randomly for a while. Basically what happens is we get a thread coming
into the allocator and reading the space cache off of disk and adding the
entries to the free space cache as we go. Then we get another thread that comes
in and tries to allocate from that block group. Since block_group->cached !=
BTRFS_CACHE_NO it goes ahead and tries to do the allocation. We do this because
if we're doing the old slow way of caching we don't want to hold people up and
wait for everything to finish. The problem with this is we could end up
discarding the space cache at some arbitrary point in the future, which means we
could very well end up allocating space that is either bad, or when the real
caching happens it could end up thinking the space isn't in use when it really
is and cause all sorts of other problems.
The solution is to add a new flag to indicate we are loading the free space
cache from disk, and always try to cache the block group if cache->cached !=
BTRFS_CACHE_FINISHED. That way if we are loading the space cache anybody else
who tries to allocate from the block group will have to wait until it's finished
to make sure it completes successfully. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
For the user it is confusing to find something like:
[10197.627710] new size for /dev/mapper/vg0-usr_share is 3221225472
in kernel log, because it doesn't point directly to btrfs.
This patch prefixes those messages with "btrfs:" like other btrfs
related printks.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Round inode bytes and delalloc bytes up to real blocksize before
converting to sector size. Otherwise eg. files smaller than 512
are reported with zero blocks due to incorrect rounding.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
setup_cluster_no_bitmap() searches all the extents and bitmaps starting
from offset. Therefore if it returns -ENOSPC, all the bitmaps starting
from offset are in the bitmaps list, so it's sufficient to search from
this list in setup_cluser_bitmap().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Suppose there are two bitmaps [0, 256], [256, 512] and one extent
[100, 120] in the free space cache, and we want to setup a cluster
with offset=100, bytes=50.
In this case, there will be only one bitmap [256, 512] in the temporary
bitmaps list, and then setup_cluster_bitmap() won't search bitmap [0, 256].
The cause is, the list is constructed in setup_cluster_no_bitmap(),
and only bitmaps with bitmap_entry->offset >= offset will be added
into the list, and the very bitmap that convers offset has
bitmap_entry->offset <= offset.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
My previous patch introduced some u64 for failed_mirror variables, this one
makes it consistent again.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch casts to unsigned long before casting to a pointer and fixes
the following warnings:
fs/btrfs/extent_io.c:2289:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
fs/btrfs/ioctl.c:2933:37: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
fs/btrfs/ioctl.c:2937:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
fs/btrfs/ioctl.c:3020:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
fs/btrfs/scrub.c:275:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
fs/btrfs/backref.c:686:27: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When btrfs is writing the super blocks, it send barrier flushes to make
sure writeback caching drives get all the metadata on disk in the
right order.
But, we have two bugs in the way these are sent down. When doing
full commits (not via the tree log), we are sending the barrier down
before the last super when it should be going down before the first.
In multi-device setups, we should be waiting for the barriers to
complete on all devices before writing any of the supers.
Both of these bugs can cause corruptions on power failures. We fix it
with some new code to send down empty barriers to all devices before
writing the first super.
Alexandre Oliva found the multi-device bug. Arne Jansen did the async
barrier loop.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Reported-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
When entering softif_create(), the rtnl lock has already been acquired
by store_mesh_iface().
(store_mesh_iface() -> hardif_enable_interface() -> softif_create)
In case of an error, we should therefore call unregister_netdevice()
instead of unregister_netdev().
unregister_netdev() tries to acquire the rtnl lock itself and deadlocks
in this situation. unregister_netdevice() assumes that the rtnl lock
is already been held.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
if hash_add() fails, we should remove the structure to avoid memory
leaks.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The tt_local_reset_flags() is actually used for one use case only. It is not
generalised enough to be used indifferent situations. This patch make it general
enough in order to let other code use it whenever a flag set is requested over
the whole hash table (passed as parameter). The function is now called
tt_set_flags()
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The check for new packets in the future used a wrong binary operator,
which makes the check expression always true and accepting too many
packets.
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Several functions in the translation table management code assume that the
tt_global_entry and tt_local_entry structures have the same initial fields such
as 'addr' and 'hash_entry'. To improve the code readability and to avoid
mistakes in later changes, a common substructure that substitute the shared
fields has been introduced (struct tt_common_entry).
Thanks to this modification, it has also been possible to slightly reduce the
code length by merging some functions like compare_ltt/gtt() and
tt_local/global_hash_find()
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Before accessing the TT_RESPONSE packet payload, the node has to ensure that the
packet is long enough as it would expect to be.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The TT_RESPONSE skb has to be linearised only if the node plans to access the
packet payload (so only if the message is directed to that node). In all the
other cases the node can avoid this memory operation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the translation tables (global and local) are written for debugfs,
it is not neccesary to allocate a buffer, we can directly use
seq_printf() to print them out.
This might actually be safer if the table changes between size
calculation and traversal, and we can't estimate the required size
wrong.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There are two reasons for this fix:
- the result of choose_orig() and vis_choose() is an index and therefore it can't
be negative. Hence it is correct to make the return type unsigned too.
- sizeof(int) may not be the same on ALL the architectures. Since we plan to use
choose_orig() as DHT hash function, we need to guarantee that, given the same
argument, the result is the same. Then it is correct to explicitly express
the size of the return type (and the second argument). Since the expected
length is currently 4, uint32_t is the most convenient choice.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
get_orig_node() tries to retrieve an orig_node object based on a mac address
and creates it if not present. This is not the wanted behaviour in the
translation table code as we don't want to create new orig_code objects but
expect a NULL pointer if the object does not exist.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When deleting the entries, tt_global_del_orig() has to print the message passed
as argument instead of a static one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Prevent tracing of preempt_disable() in get_cpu_var() in
kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled,
preempt_disable/enable() are traced and this causes the function_graph
tracer to go into an infinite recursion. By open coding the
preempt_disable() around the get_cpu_var(), we can use the notrace
version which prevents preempt_disable/enable() from being traced and
prevents the recursion.
Based on a similar patch for Xen from Jeremy Fitzhardinge.
Tested-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds a new optional chunk to the CS ioctl that specifies optional flags
to the CS parser. Why this is useful is explained below. Note that some regs
no longer need the NOP relocation packet if this feature is enabled.
Tested on r300g and r600g with this flag disabled and enabled.
Assume there are two contexts sharing the same mipmapped tiled texture.
One context wants to render into the first mipmap and the other one
wants to render into the last mipmap. As you probably know, the hardware
has a MACRO_SWITCH feature, which turns off macro tiling for small mipmaps,
but that only applies to samplers.
(at least on r300-r500, though later hardware likely behaves the same)
So we want to just re-set the tiling flags before rendering (writing
packets), right? ... No. The contexts run in parallel, so they may
set the tiling flags simultaneously and then fire their command streams
also simultaneously. The last one setting the flags wins, the other one
loses.
Another problem is when one context wants to render into the first and
the last mipmap in one CS. Impossible. It must flush before changing
tiling flags and do the rendering into the smaller mipmaps in another CS.
Yet another problem is that writing copy_blit in userspace would be a mess
involving re-setting tiling flags to please the kernel, and causing races
with other contexts at the same time.
The only way out of this is to send tiling flags with each CS, ideally
with each relocation. But we already do that through the registers.
So let's just use what we have in the registers.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (exynos4_tmu) Fix Kconfig dependency
[ Merging code in-flight, just because I can. What timezone should I
use? - Linus ]
Newer versions of MINIX can create filesystems that allocate an extra
bitmap block. Mounting of this succeeds, but doing a statfs call will
result in an oops in count_free because of a negative number being used
for the bh index.
Avoid this by verifying the number of allocated blocks at mount time,
erroring out if there are not enough and make statfs ignore the extras
if there are too many.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=18792
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
After commit 2a77c46de1
(PM / Suspend: Add statistics debugfs file for suspend to RAM)
a missing pair of braces inside the state_store() function causes even
invalid arguments to suspend to be wrongly treated as failed suspend
attempts. Fix this.
[rjw: Put the hash/subject of the buggy commit into the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
No longer at Citrix, still interested in Xen.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The USB HID Usage Tables spec defines page 6 for Generic Device Controls, the
most useful of which (to me) is Battery Strength.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__remove_hrtimer() attempts to reprogram the clockevent device when
the timer being removed is the next to expire. However,
__remove_hrtimer() reprograms the clockevent *before* removing the
timer from the timerqueue and thus when hrtimer_force_reprogram()
finds the next timer to expire it finds the timer we're trying to
remove.
This is especially noticeable when the system switches to NOHz mode
and the system tick is removed. The timer tick is removed from the
system but the clockevent is programmed to wakeup in another HZ
anyway.
Silence the extra wakeup by removing the timer from the timerqueue
before calling hrtimer_force_reprogram() so that we actually program
the clockevent for the next timer to expire.
This was broken by 998adc3 "hrtimers: Convert hrtimers to use
timerlist infrastructure".
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1321660030-8520-1-git-send-email-johlstei@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dummy, non-zero definitions for HPAGE_MASK and HPAGE_SIZE were added in
51c6f666fc ("mm: ZAP_BLOCK causes redundant work") to avoid a divide
by zero in generic kernel code.
That code has since been removed, but probably should never have been
added in the first place: we don't want HPAGE_SIZE to act like PAGE_SIZE
for code that is working with hugepages, for example, when the
dependency on CONFIG_HUGETLB_PAGE has not been fulfilled.
Because hugepage size can differ from architecture to architecture, each
is required to have their own definitions for both HPAGE_MASK and
HPAGE_SIZE. This is always done in arch/*/include/asm/page.h.
So, just remove the dummy and dangerous definitions since they are no
longer needed and reveals the correct dependencies. Tested on
architectures using the definitions with allyesconfig: x86 (even with
thp), hppa, mips, powerpc, s390, sh3, sh4, sparc, and sparc64, and with
defconfig on ia64.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: mount_subtree()
switch create_mnt_ns() to saner calling conventions, fix double mntput() in nfs
btrfs: fix double mntput() in mount_subvol()
Allow the specified syscall offset to be symbolic, e.g. a macro. For
offset system calls, this if nothing else makes the generated code
easier to read.
Suggested-by: H. J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/1321569446-20433-7-git-send-email-hpa@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
