It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that zone_sizes_init() is identical on 32-bit and 64-bit,
move the code to arch/x86/mm/init.c and use it for both
architectures.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-7-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make 32-bit and 64-bit zone_sizes_init() identical in
preparation for unification.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-6-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit has no highmem so max_low_pfn is always the same as
'max_pfn'.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-5-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In preparation for unifying 32-bit and 64-bit zone_sizes_init()
make sure ZONE_DMA32 is wrapped in CONFIG_ZONE_DMA32.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-4-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 'highend_pfn' variable is always set to 'max_pfn' so just
use the latter directly.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-3-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces a zone_sizes_init() helper function on
64-bit to make it more similar to 32-bit init.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-2-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use MAX_DMA_PFN which represents the 16 MB ISA DMA limit on
32-bit x86 just like we do on 64-bit.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1320155902-10424-1-git-send-email-penberg@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's no reason for this to be set, and it will simply introduce build
errors for others, so simply leave it unset.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
bonito board needs some settings by pmic which use i2c access.
It is dependent on the device to be used.
This patch adds standard settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
devices enable/disable are controled by dip-switch on bonito board.
If bonito core board is connected to base board,
you can check the settings from FPGA.
This patch adds basic code and controls SCIFA5 settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in entries for both Goda and Morimoto-san who have previously
used different conventions.
Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all of the named string association with clocks has been
migrated to clkdev lookups there's no meaningful named topology that can
be constructed for a debugfs tree view. Get rid of the left over bits,
and shrink struct clk a bit in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up and fix pwr_nids for 92HD71 / 73 / 83 family codecs; remove
pwr_mapping which was incorrect.
The original pwr_nids support of 92HD83xxx was incorrect and never
actually worked before. Now we should have things working correctly
without having to hack by DID anymore.
It is also not necessary to explicitly turn on all the pins near the
beginning of patch_stac92hd83xxx() now, the pins will go though
initialization properly.
Tested on 92HD66 / 71 / 73 / 75 / 83 / 89 / 91 demo boards.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>