Commit graph

286,663 commits

Author SHA1 Message Date
Ohad Ben-Cohen
c97f6dd0fe hwspinlock/omap: simplify allocation scheme
Instead of allocating every hwspinlock separately, allocate
them all in one shot.

This both simplifies the driver and helps achieving better
slab utilization.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
2011-09-21 19:45:32 +03:00
Ohad Ben-Cohen
e467b64214 hwspinlock/core: simplify 'owner' handling
Use struct device_driver's owner member instead of asking drivers to
explicitly pass the owner again.

This simplifies drivers and also save some memory, since there's no
point now in maintaining a separate owner pointer per hwspinlock.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
2011-09-21 19:45:32 +03:00
Ohad Ben-Cohen
315d8f5ccd hwspinlock/core: simplify Kconfig
Simplify hwspinlock's Kconfig by making the global CONFIG_HWSPINLOCK
entry invisible; users will just select it when needed.

This also prepares the ground for adding hwspinlock support for other
platforms (the 'depends on ARCH_OMAP4' was rather hideous, and while
we're at it, a dedicated menu is added).

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
2011-09-21 19:45:32 +03:00
Kevin Hilman
2edc7ba5e8 ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
Even when CONFIG_PM=n, we try to scale the boot voltage to a sane,
known value using OPP table to find matching voltage based on boot
frequency.  This should be done, even when CONFIG_PM=n to avoid
mis-configured bootloaders and/or boot voltage assumptions made by
boot loaders.

Also fixes various compile problems due to depenencies between voltage
domain and powerdomain code (also present when CONFIG_PM=n).

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-09-21 09:36:21 -07:00
Shawn Guo
0e44b6eccf gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
The mx3_gpio_irq_handler() is also called on imx6q which has GIC as
the primary interrupt controller.  As GIC implements the fasteoi flow
control, we need to add chained_irq_enter/exit() to
mx3_gpio_irq_handler() for signaling EOI, otherwise system will hang
whenever there is a gpio irq triggered.

v2: use chained_irq_{enter,exit}()

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-21 10:26:42 -06:00
Luiz Augusto von Dentz
ab0ff76d1b Bluetooth: mark l2cap_create_iframe_pdu as static
l2cap_create_iframe_pdu is only used in l2cap_core.c

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:16 -03:00
Andre Guedes
f8523598ee Bluetooth: Check 'dev_class' in mgmt_device_found()
The mgmt_device_found event will be used to report LE devices found
during discovery procedure. Since LE advertising reports events
doesn't have class of device information, we need to check if
'dev_class' is not NULL before copying it.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:16 -03:00
Andre Guedes
a8f13c8cd2 Bluetooth: Reduce critical region.
This patch reduces the critial region (protected by hdev->lock) in
hci_cc_le_set_scan_enable(). This way, only really required code is
synchronized.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:16 -03:00
Anderson Briglia
51beabdf62 Bluetooth: Fix wrong memcpy size on LE start encryption
This patch fixes wrong memcpy size when copying rand value to
HCI_OP_LE_START_ENC command.
The compiler pretends that the array parameter was declared as a pointer
and sizeof reports the size of the pointer. [1]

[1] http://www.c-faq.com/aryptr/aryparmsize.html

Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:16 -03:00
Vinicius Costa Gomes
ca10b5ee0c Bluetooth: Remove support for other SMP keys than the LTK
For now, only the LTK is properly supported. We are able to receive
and generate the other types of keys, but we are not able to use
them. So it's better not request them to be distributed.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:16 -03:00
Vinicius Costa Gomes
feb45eb596 Bluetooth: Fix not setting a pending security level
For slave initiated security, we should set a default security level,
for now BT_SECURITY_MEDIUM.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:15 -03:00
Vinicius Costa Gomes
a492cd52b5 Revert "Bluetooth: Add support for communicating keys with userspace"
This reverts commit 5a0a8b4974.

If we use separate messages and list for SMP specific keys we can
simplify the code.

Conflicts:

	net/bluetooth/mgmt.c

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:15 -03:00
Vinicius Costa Gomes
988c5997d3 Bluetooth: Use the LTK after receiving a LE Security Request
When receiving a security request from the remote device we should find
if there is already a LTK associated with the remote device, if found
we should use it to encrypt the link.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:15 -03:00
Vinicius Costa Gomes
0fb4eb6f63 Bluetooth: Fix sending wrong authentication requirements
Until we support any pairing method (Passkey Entry, OOB) that gives
MITM protection we shouldn't send that we have MITM protection.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:15 -03:00
Antti Julku
5e762444b0 Bluetooth: Add mgmt events for blacklisting
Add management interface events for blocking/unblocking a device.
Sender of the block device command gets cmd complete and other
mgmt sockets get the event. Event is also sent to mgmt sockets when
blocking is done with ioctl, e.g when blocking a device with
hciconfig. This makes it possible for bluetoothd to track status
of blocked devices when a third party block or unblocks a device.

Event sending is handled in mgmt_device_blocked function which gets
called from hci_blacklist_add in hci_core.c. A pending command is
added in mgmt_block_device, so that it can found when sending the
event - the event is not sent to the socket from which the pending
command came. Locks were moved out from hci_core.c to hci_sock.c
and mgmt.c, because locking is needed also for mgmt_pending_add in
mgmt.c.

Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:59:15 -03:00
Vinicius Costa Gomes
c908df362c Bluetooth: Use the MEDIUM security level for pairings
This lifts the requirement of 16 digits pin codes when pairing
with devices that do not support SSP when using the mgmt interface.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:13 -03:00
Vinicius Costa Gomes
e9bf2bf03e Bluetooth: Require authentication if MITM protection is requested
The HIGH security level requires a 16 digit pin code for non-SSP
bondings. Sometimes this requirement is not acceptable and we still
want protection againts MITM attacks (which is something that the
MEDIUM security level doesn't provide), for that we should allow
another way to request authentication without using the HIGH security
level.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
Vinicius Costa Gomes
8aab47574a Bluetooth: Move SMP crypto functions to a workqueue
The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
Vinicius Costa Gomes
1c1def09c4 Bluetooth: Move SMP fields to a separate structure
The objective is to make the core to have as little as possible
information about SMP procedures and logic. Now, all the SMP
specific information is hidden from the core.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
David Herrmann
142c69c6ea Bluetooth: hidp: Add support for NO_INIT_REPORTS quirk
During setup the host initializes all HID reports. Some devices do not
support this. If this quirk is set, we skip the initialization.
See also usbhid_init_reports() for this quirk.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
Peter Hurley
21061df3a2 Bluetooth: Add LE link type for debugfs output
Add LE link type as known connection type for debugfs stringizing
output.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
Antti Julku
f6422ec624 Bluetooth: Add mgmt command for fast connectable mode
Add command to management interface for enabling/disabling the
fast connectable mode.

Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:12 -03:00
Vinicius Costa Gomes
cfafccf730 Bluetooth: Add link_type information to the mgmt Connected event
One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:11 -03:00
Vinicius Costa Gomes
160dc6ac12 Bluetooth: Add support for running SMP without a socket
When doing the pairing procedure we won't have an associated
socket, but we still have to do the SMP negotiation. This
adds support for encrypting the link and exchanging keys.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:11 -03:00
Vinicius Costa Gomes
7a512d0172 Bluetooth: Add support for pairing via mgmt over LE
Using the advertising cache we are able to infer the type
of the remote device, and so trigger pairing over the correct
link type.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:11 -03:00
Vinicius Costa Gomes
454d48ff70 Bluetooth: Use the same timeouts for both ACL and LE links
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:11 -03:00
Vinicius Costa Gomes
d26a234548 Bluetooth: Add a flag to indicate that SMP is going on
Add HCI_CONN_LE_SMP_PEND flag to indicate that SMP is pending
for that connection. This allows to have information that an SMP
procedure is going on for that connection.

We use the HCI_CONN_ENCRYPT_PEND to indicate that encryption
(HCI_LE_Start_Encryption) is pending for that connection.

While a SMP procedure is going on we hold an reference to the
connection, to avoid disconnections.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:11 -03:00
Vinicius Costa Gomes
e2dcd113d1 Bluetooth: Reset the security timer when a command is queued
Each time a SMP command is enqueued, we reset the SMP timer,
this way we follow exactly what the spec mandates:

"The Security Manager Timer shall be reset when an L2CAP SMP command is
queued for transmission." Vol. 3, Part H, Section 3.4

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:10 -03:00
Luiz Augusto von Dentz
52087a792c Bluetooth: make use of connection number to optimize the scheduler
This checks if there is any existing connection according to its type
before start iterating in the list and immediately stop iterating when
reaching the number of connections.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-21 12:58:10 -03:00
David Daney
0f4ccbc835 MIPS: No branches in delay slots for huge pages in handle_tlbl
For the case PM_DEFAULT_MASK == 0, we were placing a branch in the
delay slot of another branch.  This leads to undefined behavior.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2775/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:54:07 +02:00
David Daney
d968275921 MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
Reported-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/2753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:54:02 +02:00
David Daney
465aaed003 MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
Current Octeon systems do in fact have holes in their memory zones.
We need to select HOLES_IN_ZONE.  If we do not, some memory
configurations will result in crashes at boot time like this:

.
.
.
CPU 6 Unable to handle kernel paging request at virtual address 0000000000700000, epc == ffffffff8118fe00, ra == ffffffff8118fe9c
Oops[#1]:
Cpu 6
.
.
.
        ...
Call Trace:
[<ffffffff8118fe00>] setup_per_zone_wmarks+0x1b0/0x338
[<ffffffff815cd738>] init_per_zone_wmark_min+0x64/0xd0
[<ffffffff81100438>] do_one_initcall+0x38/0x160
.
.
.

Reported-by: Jason Kwon <jason.kwon@ericsson.com>
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Cc: Jason Kwon <jason.kwon@ericsson.com>
Patchwork: https://patchwork.linux-mips.org/patch/2724/
Tested-by: Guenter Roeck<guenter.roeck@ericsson.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:56 +02:00
Rafael J. Wysocki
bd7100099a MIPS: PM: Use struct syscore_ops instead of sysdevs for PM (v2)
Convert some MIPS architecture's code to using struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.

This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-and-tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: "Rafael J.  Wysocki" <rjw@sisk.pl>
Patchwork: http://patchwork.linux-mips.org/patch/2431/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:51 +02:00
Yong Zhang
1eec6cd08b MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
We can't trust userspace to pass signed-extend arguments.  Not correctly
sign-extended arguments to futex-wait result in architecturally undefined
operation of 32-bit arithmetic instructions.

For example, if 'val' is too big and bit-31 is 1, the caller may enter
endless loop at:

futex_wait_setup()
{
	...

	if (uval != val) {
		queue_unlock(q, *hb);
		ret = -EWOULDBLOCK;

	...
}

Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2714/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:44 +02:00
Arnaud Lacombe
b8ecf341f1 MIPS: Do not use EXTRA_CFLAGS
Usage of these flags has been deprecated for nearly 4 years by:

    commit f77bf01425
    Author: Sam Ravnborg <sam@neptun.(none)>
    Date:   Mon Oct 15 22:25:06 2007 +0200

        kbuild: introduce ccflags-y, asflags-y and ldflags-y

Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.

Replace their usage by Kbuild's `{as,cc,ld}flags-y'.

To: linux-kernel@vger.kernel.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/2710/
Cc: linux-mips@linux-mips.org
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:38 +02:00
Manuel Lauss
dd0a028183 MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
Disable the cascade IRQ in the cascade handler.  This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:32 +02:00
John Crispin
b7867f1bfc SERIAL: Lantiq: Set timeout in uart_port
Without this patch apps using readline hang.

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-serial@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2687/
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:25 +02:00
John Crispin
0596954681 MIPS: Lantiq: Fix setting the PCI bus speed on AR9
The bits used to set the PCI bus speed on AR9 are slightly different to
those used on Danube.

Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2614/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:18 +02:00
John Crispin
77fbdb30f0 MIPS: Lantiq: Fix external interrupt sources
The irq base offset needs to be ignored when matching irqs to external
interrupt pins. Taking the offset into account resulted in the EIU not
being brought up properly.

Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2616/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:12 +02:00
Ralf Baechle
d954ffe34a MIPS: tlbex: Fix build error in R3000 code.
Only some GCC versions such as gcc 4.2 notice that the variable wr in
build_r3000_tlb_modify_handler is used uninitialized.  When using one
of those GCCs the build will fail due to -Werror.  GCC 4.6 does not
warn about the uninitialized use of wr.

This issue was introduced by 7211f4d7a3dcbe57c5d396c334dca525315dceb2
[MIPS: Close races in TLB modify handlers.]

Reported-by: Ganesan Ramalingam <ganesan18@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:07 +02:00
Manuel Lauss
870168a031 MIPS: Alchemy: Include Au1100 in PM code.
The current code forgets the Au1100 when looking for the correct method to
suspend the chip.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:53:01 +02:00
Manuel Lauss
c78c488273 MIPS: Alchemy: Fix typo in MAC0 registration
Harmless typo which prints an error message although MAC0 was registered
successfully.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:52 +02:00
Ralf Baechle
a705dc7cf4 MIPS: MSP71xx: Fix build error.
CC      arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1

caused by 57336bc1056798d89714b7fb1b1d197e6bda6819 [MIPS: Mark cascade and
low level interrupts IRQF_NO_THREAD].

Commas to separate struct initializers generally are considered useful to
enhance the compilation experience of the user.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:44 +02:00
Ralf Baechle
1f717929e9 MIPS: Handle __put_user() sleeping.
do_signal() does __put_user() which can fault, resulting in a might_sleep()
warning in down_read(&mm->mmap_sem) and a "scheduling while atomic" warning
when mmap_sem is contented. On Swarm this also results in:

WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:

[<ffffffff804b48a4>] dump_stack+0x1c/0x50
[<ffffffff8013dc94>] warn_slowpath_common+0x8c/0xc8
[<ffffffff8013dcfc>] warn_slowpath_null+0x2c/0x40
[<ffffffff801864a0>] smp_call_function_many+0x148/0x398
[<ffffffff80186748>] smp_call_function+0x58/0xa8
[<ffffffff80119b5c>] r4k_flush_data_cache_page+0x54/0xd8
[<ffffffff801f39bc>] handle_pte_fault+0xa9c/0xad0
[<ffffffff801f40d0>] handle_mm_fault+0x158/0x200
[<ffffffff80115548>] do_page_fault+0x218/0x3b0
[<ffffffff80102744>] ret_from_exception+0x0/0x10
[<ffffffff8010eb18>] copy_siginfo_to_user32+0x50/0x298
[<ffffffff8010edf0>] setup_rt_frame_32+0x90/0x250
[<ffffffff80106414>] do_notify_resume+0x154/0x358
[<ffffffff80102930>] work_notifysig+0xc/0x14

Fixed by enabling interrupts in do_notify_resume before delivering signals.

[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume.  Which is saner
than doing it in entry.S.]

Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:38 +02:00
Thomas Gleixner
0f462e3c12 MIPS: Allow forced irq threading
All low level interrupts have been marked NO_THREAD, so MIPS can enjoy
the wonderful world of forced threaded interrupt handlers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:34 +02:00
Liming Wang
5c22cd4075 MIPS: i8259: Mark cascade interrupt non-threaded
Cascade interrupts cannot be threaded.

Signed-off-by: Liming Wang <liming.wang@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1314370804-21266-1-git-send-email-liming.wang@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:28 +02:00
Wu Zhangjin
77cbece767 MIPS: Loongson: Mark cascade interrupts IRQF_NO_THREAD
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:22 +02:00
Wu Zhangjin
5a4a4ad851 MIPS: Mark cascade and low level interrupts IRQF_NO_THREAD
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:15 +02:00
Wu Zhangjin
4d85f6afa4 MIPS: Make the die_lock be raw
On preempt-rt this lock needs to be raw, so it does not get converted
to a sleeping spinlock. Trying to sleep in a panic is not really
desireable.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:09 +02:00
Thomas Gleixner
49de830ad7 MIPS: Ftrace: Fix the CONFIG_DYNAMIC_FTRACE=n compile
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-09-21 17:52:04 +02:00