When driver detect queue stuck, display current read/write pointer before
perform frimware reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reaches encapsulation for this file. In order to reach this:
* move priv->valid_context to iwl_shared
* move the last_rejected initialization to the upper layer
* define a wrapper iwl_nic_config in the upper layer that calls to
cfg->lib->ops->nic_config
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The traffic log debugfs handlers were mistakenly moved to the
transport layer because they print the pointers of the Tx / Rx
queues. The pointers of the queues can be fetched by another debugfs
handler.
So bring the traffic log back to the upper layer and remove the part
that reads the Tx / Rx queues' pointers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move a few declarations needed by the transport layer to iwl-shared.h
Move iwl_cmd_meta, iwl_tx_queue and friends to the internal transport
header file.
Move iwl_device_cmd iwl_host_cmd and friends to iwl-trans.h since
these structs are used in the API to the transport layer.
Move get_cmd_string to the upper layer with a declaration in
iwl-shared.h.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another round of clean up on the transport layer.
Define a wrapper around wiphy_rfkill_set_hw_state to prevent the
transport layer from accessing priv->hw.
Also move wait_command_queue to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latter was the only place that called the first. The two
functions were split when the iwl_pci_probe called iwl_pci_down
upon failure in the probe. Since iwl_pci_probe undoes its work by
itself, there is no need to split between iwl_pci_down, and
iwl_pci_remove.
Thanks to Pavel Roskin for pointing that out.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During init time, only the necessary calibration should be performed. This
not only save time, also avoid uCode crash because lack of necessary information.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix Tx IQ Calibration hang issue in
AR9003 chips" did not consider more than one potential sample
while calculating magnitude/phase average if more than one
sample has the same value which could affect post-processing
of outlier detection that causes an undesirable Tx IQ
correction value will be assigned to tx gain settings where
outlier happens.
Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Paul Stewart <pstew@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch protects cycle counters access by cc_lock
and also prints current sample index.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the samples debugfs which maintains the snapshorts of
mac/bb only on associated state. Hence to cover issues on idle
state, the samples are taken whenever the driver is ready.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso optimised the timer to not run all the
time in commit 3393a608c4.
However, after that it will still run once
more even if all frames just expired. Fixing
that also makes the function return value a
little clearer in the process.
Also, while at it, change the return value
to bool (instead of int).
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed in "Licensing wlc_phy_radio.h and brcm80211" (Message-ID:
<AANLkTinQMRGkOvi4e4JMsHGV_BF_4Rf5oHCtZgQjwQ1g@mail.gmail.com>) content
of that file is not copyrightable, just names and numbers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minstrel HT tries very hard to establish a BA session with
each peer once there's some data on the way. However the
stack does not inform minstrel if an aggregation session
is already in place, so it keeps trying and wastes good
cycles in the tx status path.
[ 8149.946393] Open BA session requested for $AP tid 0
[ 8150.048765] Open BA session requested for $AP tid 0
[ 8150.174509] Open BA session requested for $AP tid 0
[ 8150.274376] Open BA session requested for $AP tid 0
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On MIMO chips this can be used to enable/disable hardware chains, ensuring
that the MCS information is updated accordingly.
On non-MIMO chips with rx diversity (e.g. 9285), this configures the rx
input antenna.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reduces unnecessary code duplication. Also takes the sc_pcu_lock within
ath_reset instead of callsites, which makes it possible to always cancel
all queued work items before the reset, possibly fixing a few race
conditions (work items vs reset) along with it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it much easier to add further rework to avoid race conditions
between reset and other work items.
Move other functions to make ath_reset static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helps with making ath_reset static in the next commit
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumption is that during the hw config, transmission was
already stopped by mac80211. Sometimes the AP can be switching
b/w the ht modes due to intolerant or etc where STA is in
the middle of transmission. In such scenario, buffer overflow
was observed at driver side. And also before updating the rate
control, the frames are continued to xmited with older rates.
This patch ensures that the frames are always xmitted with
updated rates and avoid buffer overflow.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device. In mesh, however, we also need to stop
forwarding traffic. This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To check whether a frame is in the RMC, we need access to the mesh
header. This header is encrypted in encrypted data frames, so make this
check after the frame has been decrypted.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rule to copy this file doesn't have to be forced. However
lib1funcs.[So] have to be listed amongst the targets.
This prevents zImage from being recreated needlessly.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Some old bootloaders can't be updated to a device tree capable one,
yet they provide ATAGs with memory configuration, the ramdisk address,
the kernel cmdline string, etc. To allow a device tree enabled
kernel to be used with such bootloaders, it is necessary to convert those
ATAGs into FDT properties and fold them into the DTB appended to zImage.
Currently the following ATAGs are converted:
ATAG_CMDLINE
ATAG_MEM
ATAG_INITRD2
If the corresponding information already exists in the appended DTB, it
is replaced, otherwise the required node is created to hold it.
The code looks for ATAGs at the location pointed by the value of r2 upon
entry into the zImage code. If no ATAGs are found there, an attempt at
finding ATAGs at the typical 0x100 offset from start of RAM is made.
Otherwise the DTB is left unchanged.
Thisstarted from an older patch from John Bonesio <bones@secretlab.ca>,
with contributions from David Brown <davidb@codeaurora.org>.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This is a small subset of string functions needed by commits to come.
Except for memcpy() which is unchanged from its original location, their
implementation is meant to be small, and -Os is enforced to prevent gcc
from doing pointless loop unrolling.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The appended DTB gets relocated with the decompressor code to get out
of the way of the decompressed kernel. However the kernel's .bss section
may be larger than the relocated code and data, and then the DTB gets
overwritten. Let's make sure the relocation takes care of moving zImage
far enough so no such conflict with .bss occurs.
Thanks to Tony Lindgren <tony@atomide.com> for figuring out this issue.
While at it, let's clean up the code a bit so that the wont_overwrite
symbol is used while determining if a conflict exists, making the above
change more precise as well as eliminating some ARM/THUMB alternates.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This patch provides the ability to boot using a device tree that is appended
to the raw binary zImage (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
Signed-off-by: John Bonesio <bones@secretlab.ca>
[nico: ported to latest zImage changes plus additional cleanups/improvements]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the incorrect indentation in functions fb_try_mode() and fb_find_mode().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is needed for proper alignment when the DTB appending feature
is used.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over overlay id's to shorten _dispc_set_color_conv_coef()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_dump_regs().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).
Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make the debug message useful by printing the name of the device
that no associated driver could be found for.
Signed-off-by: Andy Doan <andy.doan@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>