Commit graph

262,410 commits

Author SHA1 Message Date
Richard Fitzgerald
e2ae0fbc73 mfd: arizona: Fix incorrect Makefile conditionals
The use of ifneq against 'n' to conditionally compile codec-specific
parts is wrong and was resulting in all the codec tables being built
even for deselected codecs.

Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:19 +01:00
Lorenzo Pieralisi
ec40c606c7 mfd: Check ACPI device companion before checking resources
Current code in mfd-core calls into ACPI to check resources even
on a system that booted with a DT (on kernels with both DT and ACPI
support compiled in). This triggers ACPI exceptions since we may
end up calling the ACPI interpreter when it has not been initialized:

"ACPI Exception: AE_BAD_PARAMETER, Thread 2064154624 could not acquire
Mutex [0x1] (20150410/utmutex-285)"

This patch fixes the issues by adding a check for an ACPI companion
device before carrying out ACPI resources checks to avoid calling
the ACPI interpreter if the fwnode representing the device is an OF one.

Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:17 +01:00
Richard Fitzgerald
fc027d138b mfd: arizona: Split INx_MODE into two fields
Later arizona silicon has the single/differential selector
in a different register, and IN1_MODE only selects between
analogue or digital. Prepare for this by splitting the
INx_MODE definition into two fields.

Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:16 +01:00
Charles Keepax
121c075c1f mfd: wm5110: Add delay before releasing reset line
On the wm5110 it is important the reset line is held for slightly longer
to ensure the device starts up well. This patch adds a 5mS delay for
this.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:15 +01:00
Charles Keepax
e6cb73410a mfd: arizona: Add better support for system suspend
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:14 +01:00
Charles Keepax
96129a0eaa mfd: wm5110: Set DCVDD voltage to 1.175V before entering sleep mode
The low power sleep mode on wm5110 requires that the LDO1 regulator be
set to 1.175V prior to entering sleep, then returned to 1.2V after
exiting sleep mode. This patch apply these regulator settings.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:13 +01:00
Charles Keepax
882bc46813 mfd: wm5110: Add register patch required for low power sleep
Some register settings must be applied before the first time low power
sleep mode is entered on the wm5110 to ensure optimium performance.
These settings require SYSCLK to be enabled whilst they are being
applied. This patch applies the settings using the recently factored out
boot time SYSCLK functionality.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:13 +01:00
Charles Keepax
3850e3ee86 mfd: arizona: Factor out SYSCLK enable from wm5102 hardware patch
wm5102 applies a custom hardware boot sequence, for this the SYSCLK
needs to be enabled. This patch factors out the code that enables
SYSCLK for this sequence such that it can be used for other boot time
operations that require SYSCLK.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:12 +01:00
Charles Keepax
0be068a077 mfd: arizona: Fix formating/style issues in arizona_apply_hardware_patch
In preparation for some refactoring fixup some minor style, formating
and code clarity issues.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:11 +01:00
Charles Keepax
1c1c6bba57 mfd: wm5102: Ensure we always boot the device fully
The wm5102 uses a custom boot sequence and the standard boot sequence is
disabled. However, the standard boot sequence must be run at least once
after a cold boot (caused by either a hard reset or removal of AVDD).
Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
hardware reset. This means if the device has been previously booted but
the AVDD supply has never been removed, arizona_dev_init will reset the
chip but the boot sequence will not run, which can cause numerous
problems. The solution is to manually clear this register and then boot
the chip again, which is what this patch does.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:10 +01:00
Charles Keepax
2229875dc0 mfd: arizona: Factor out hard reset into helper functions
This patch adds functions for enabling and disabling the physical reset
line. This will be helpful in future refactoring.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:09 +01:00
Charles Keepax
5f056bf042 mfd: arizona: Use devres to manage reset GPIO
This also handily fixes a leak of the GPIO in arizona_dev_exit.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:08 +01:00
Geert Uytterhoeven
6fafecc12d mfd: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:06 +01:00
Tony Lindgren
5c188d7482 mfd: twl4030-power: Fix pmic for boards that need AC charger disabled
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.

Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.

Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:04 +01:00
Charles Keepax
b375e9f90f mfd: arizona: Remove redundant register sync
This soft reset used to be located after the register patch had been
applied, but has since moved to before the patch is applied. At the new
location there is no requirement to do a register sync as no register
writes will have happened yet.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:03 +01:00
Krzysztof Kozlowski
7ce7b26f84 mfd: Constify regmap and irq configuration data
Constify in various drivers configuration data which is not modified:
 - regmap_irq_chip,
 - individual regmap_irq's in array,
 - regmap_config,
 - irq_domain_ops,

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:01 +01:00
Lee Jones
79aa79342c Merge branches 'ib-mfd-watchdog-rtc-4.2', 'ib-mfd-regulator-4.2' and 'ib-mfd-i2c-input-chrome-4.2' into ibs-for-mfd-merged 2015-06-22 12:24:25 +01:00
Lee Jones
cf649e0076 mfd: cros_ec: Staticise some newly introduced structures
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:23:02 +01:00
Alexandru M Stan
ff4378f4b8 mfd: cros_ec: spi: Add delay for asserting CS
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. This is configurable via a DT property
"google,cros-ec-spi-pre-delay".

This patch makes the cros_ec_spi driver to cause a delay before
the beginning of a SPI transaction, to make sure that the EC has
already woken up, if the property has been defined in the DTS.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:24 +01:00
Gwendal Grignou
57b33ff077 mfd: cros_ec: Support multiple EC in a system
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.

Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.

Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:23 +01:00
Stephen Barber
d365407079 mfd: cros_ec: add bus-specific proto v3 code
Add proto v3 support to the SPI, I2C, and LPC.

Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:22 +01:00
Stephen Barber
2c7589af3c mfd: cros_ec: add proto v3 skeleton
Add support in cros_ec.c to handle EC host command protocol v3.
For v3+, probe for maximum shared protocol version and max
request, response, and passthrough sizes. For now, this will
always fall back to v2, since there is no bus-specific code
for handling proto v3 packets.

Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:21 +01:00
Javier Martinez Canillas
062476f24a mfd: cros_ec: Move protocol helpers out of the MFD driver
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.

The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.

Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:20 +01:00
Stephen Barber
256ab950bd mfd: cros_ec: rev cros_ec_commands.h
Update cros_ec_commands.h to the latest version in the EC
firmware sources and add power domain and passthru commands.

Also, update lightbar to use new command names.

Signed-off-by: Stephen Barber <smbarber@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:20 +01:00
Javier Martinez Canillas
a841178445 mfd: cros_ec: Use a zero-length array for command data
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.

This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.

So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.

Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:19 +01:00
Todd Broch
bb03ffb96c mfd: cros_ec: Instantiate sub-devices from device tree
If the EC device tree node has sub-nodes, try to instantiate them as
MFD sub-devices.  We can configure the EC features provided by the board.

Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:18 +01:00
Gwendal Grignou
e7b707f968 mfd: cros_ec: Remove parent field
Parent and device were pointing to the same device structure.

Parent is unused, removed.

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:17 +01:00
Chen-Yu Tsai
6d4fa89dcd mfd: axp20x: Enable AXP22X regulators
Now that the axp20x-regulators driver supports different variants of the
AXP family, we can enable regulator support for AXP22X without the risk
of incorrectly configuring regulators.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-05-13 16:26:34 +01:00
Boris BREZILLON
1b82b4e4f9 regulator: axp20x: Add support for AXP22X regulators
Add AXP22X regulator definitions and variant id associations.
This introduces a new "switch" type output for one of the regulators.
It is a switchable secondary output of one regulator, with the same
voltage level as the primary output.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Moved variant choosing to multi family support patch]
[wens@csie.org: Add dc-dc work frequency range]
[wens@csie.org: Add "switch" type output regulator DC1SW]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-05-13 16:26:18 +01:00
Boris BREZILLON
866bd951f2 regulator: axp20x: Prepare support for multiple AXP chip families
Rework the AXP20X_ macros and probe function to support the several chip
families, so that each family can define it's own set of regulators.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Support different DC-DC work frequency ranges]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-05-13 16:26:04 +01:00
Boris BREZILLON
f05be589ff mfd: axp20x: Add AXP22x PMIC support
Add support for the AXP22x PMIC devices to the existing AXP20x driver.
This includes the AXP221 and AXP223, which are identical except for
the external data bus. Only AXP221 is added for now. AXP223 will be
added after it's Reduced Serial Bus (RSB) interface is supported.

AXP22x defines a new set of registers, power supplies and regulators,
but most of the API is similar to the AXP20x ones.

A new irq chip definition is used, even though the available interrupts
on AXP22x is a subset of those on AXP20x. This is done so the interrupt
numbers match those on the datasheet.

This patch only enables the interrupts, system power-off function, and PEK
sub-device. The regulator driver must first support different variants
before we enable it from the mfd driver.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: fix interrupts and move regulators to separate patch]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-05-13 16:25:35 +01:00
Linus Torvalds
101a6fd387 Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
 "One intel fix, one rockchip fix, and a bunch of radeon fixes for some
  regressions from audio rework and vm stability"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
  drm/radeon: fix userptr return value checking (v2)
  drm/radeon: check new address before removing old one
  drm/radeon: reset BOs address after clearing it.
  drm/radeon: fix lockup when BOs aren't part of the VM on release
  drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
  drm/radeon: adjust pll when audio is not enabled
  drm/radeon: only enable audio streams if the monitor supports it
  drm/radeon: only mark audio as connected if the monitor supports it (v3)
  drm/radeon/audio: don't enable packets until the end
  drm/radeon: drop dce6_dp_enable
  drm/radeon: fix ordering of AVI packet setup
  drm/radeon: Use drm_calloc_ab for CS relocs
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers
2015-05-03 18:15:48 -07:00
Dave Airlie
71aee81937 Merge tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
2015-05-04 08:56:47 +10:00
Dave Airlie
df9ebeb2da Merge branch 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers
2015-05-04 08:56:27 +10:00
Linus Torvalds
61f06db00e SCSI fixes on 20150503
This is three logical fixes (as 5 patches).  The 3ware class of drivers were
 causing an oops with multiqueue by tearing down the command mappings after
 completing the command (where the variables in the command used to tear down
 the mapping were no-longer valid). There's also a fix for the qnap iscsi
 target which was choking on us sending it commands that were too long and a
 fix for the reworked aha1542 allocating GFP_KERNEL under a lock.
 
 Signed-off-by: James Bottomley <JBottomley@Odin.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQEcBAABAgAGBQJVRkgEAAoJEDeqqVYsXL0MZbEIAL7Repky0TI1GvyYVpbJLSc+
 SlJurEQ9DIpsnNtHJlEfLHicqsrK3v/xS+3Kopd1OUEIjQ0kTFPkenTiJbwFNIB+
 l7D3V1EfEdnOki7F8KU5bFf3i4KWeEUZ4v/FR3PC7dz4cFRav7OrMoGaA36yT/ns
 I4NFZ7iOa/6QXzfrywTDU5HbHgQYIN2MfCPy/NrVP95Yq09TkN5ulXDz/h6PD6Iy
 GV/RmeckUqkdO5SZq9kkIgR/czLpVCaqpf3/G6lFdfunNkhQJ96lQTzYwbvtPBrJ
 m6+sxrcCWlHzIkJsXrKtopPYzSzGdApLSsZjuYtP3RJD0uO9psfgW8pbls3dDCg=
 =n4aD
 -----END PGP SIGNATURE-----

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
 "This is three logical fixes (as 5 patches).

  The 3ware class of drivers were causing an oops with multiqueue by
  tearing down the command mappings after completing the command (where
  the variables in the command used to tear down the mapping were
  no-longer valid).  There's also a fix for the qnap iscsi target which
  was choking on us sending it commands that were too long and a fix for
  the reworked aha1542 allocating GFP_KERNEL under a lock"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: fix command completion race
  3w-xxxx: fix command completion race
  3w-sas: fix command completion race
  aha1542: Allocate memory before taking a lock
  SCSI: add 1024 max sectors black list flag
2015-05-03 13:22:32 -07:00
Linus Torvalds
3333222484 Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave dmaengine fixes from Vinod Koul:
 "Here are the fixes in dmaengine subsystem for rc2:

   - privatecnt fix for slave dma request API by Christopher

   - warn fix for PM ifdef in usb-dmac by Geert

   - fix hardware dependency for xgene by Jean"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: increment privatecnt when using dma_get_any_slave_channel
  dmaengine: xgene: Set hardware dependency
  dmaengine: usb-dmac: Protect PM-only functions to kill warning
2015-05-03 10:49:04 -07:00
Linus Torvalds
6c3c1eb3c3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...
2015-05-01 20:51:04 -07:00
Linus Torvalds
6fa72720a6 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph RBD fix from Sage Weil.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: end I/O the entire obj_request on error
2015-05-01 20:35:39 -07:00
Ilya Dryomov
082a75dad8 rbd: end I/O the entire obj_request on error
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed.  Otherwise block layer ends up confused and we
trip on

    rbd_assert(more ^ (which == img_request->obj_request_count));

in rbd_img_obj_callback() due to more being true no matter what.  We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.

A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.

Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
2015-05-01 16:44:30 -07:00
Linus Torvalds
4a152c3913 Power management and ACPI fixes for v4.1-rc2
- Fix for a regression in the cpuidle core introduced by one of
    the recent commits in the clockevents_notify() removal series
    that put a call to a function which had to be executed with
    disabled interrupts into a code path running with enabled
    interrupts (Rafael J Wysocki).
 
  - Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
    of the recent ACPICA tools commits that added a duplicate typedef
    to one of the ACPICA's header files by mistake (Olaf Hering).
 
  - Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
    driver introduced during the 3.18 development cycle causing the
    smart battery manager to be marked as not present when it should
    be marked as present (Chris Bainbridge).
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJVQoeSAAoJEILEb/54YlRxuscP/3Vz98JY0P7sMLnxVU8RPBxW
 cBN7G7F1gZup66/yV3MzvYHbgOFwNdQ2aMVxN+qV7rVMw27uwHljVr3svB+/GS15
 TeyKxvFWZYwhPKdsNAoHdkGBsptAK4DdyA+N2wH3MZ4dd8HepxpBG6QvzaEt4s43
 wFhhFrzEP3HDjrPoF/7TwKbsSrFuU5/U5PTd3dIuukj6JAl0PWnjczuVsg1PRyCW
 9kvefs3U56s8GbWOhDC+QyQ3eYJ2y35j/XnCKFWwljcdnis6HpsKj+oxSG2o0K4o
 9LLL3MgnTQuFbenuFIJUsMdFFdFrFkEeiV1EAdKCzQcXdlipxvi2cPttdNWVd6eZ
 JobXyhq7iYUQK5E5Dp6TCokxhzOyjvTo7VmEkkkqLVmfeO0FnggUAduRMAIacYXS
 ZML45m4UtvCJRoQXXxyzwYQXFeRD/nJQlOavC95jGGqtAij0Xk4xqTauQKIiqiaE
 zobOJ5ZxJMP+njFfzyDxjm68LjobYm1fUJTpWzpUSExjEKImRcw/QMzw23MyHHUL
 IJ7hP8FcELglkZWk/0ZwoNhbwM5Q2qGX5WMtqyunNFcf83aBsCr8bSjOrm4zmuL7
 NWjjeXuYwzPuC7SnFqf2K/CCfdkrdnU1frKLTpOm8t8W0P4mr1ckYrPemNemr8sN
 e5GozK5m13T2gTT4+q6M
 =v78a
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management and ACPI fixes from Rafael Wysocki:
 "Three regression fixes this time, one for a recent regression in the
  cpuidle core affecting multiple systems, one for an inadvertently
  added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
  and one for an ACPI Smart Battery Subsystem driver regression
  introduced during the 3.18 cycle (stable-candidate).

  Specifics:

   - Fix for a regression in the cpuidle core introduced by one of the
     recent commits in the clockevents_notify() removal series that put
     a call to a function which had to be executed with disabled
     interrupts into a code path running with enabled interrupts (Rafael
     J Wysocki)

   - Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
     of the recent ACPICA tools commits that added a duplicate typedef
     to one of the ACPICA's header files by mistake (Olaf Hering)

   - Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
     driver introduced during the 3.18 development cycle causing the
     smart battery manager to be marked as not present when it should be
     marked as present (Chris Bainbridge)"

* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: Run tick_broadcast_exit() with disabled interrupts
  ACPI / SBS: Enable battery manager when present
  ACPICA: remove duplicate u8 typedef
2015-04-30 14:23:31 -07:00
Markus Pargmann
e813bb2b95 net: fec: Fix RGMII-ID mode
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.

So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-30 16:48:53 -04:00
Ido Shamay
07841f9d94 net/mlx4_en: Schedule napi when RX buffers allocation fails
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-30 16:47:50 -04:00
Tony Camuso
c232d8a8bb netxen_nic: use spin_[un]lock_bh around tx_clean_lock
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.

This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.

Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-30 16:37:29 -04:00
David Ahern
17d5ceb6e4 net/mlx4_core: Fix unaligned accesses
Addresses the following kernel logs seen during boot:

Kernel unaligned access at TPC[100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]

Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-30 16:26:30 -04:00
Benjamin Poirier
f94813f3c1 mlx4_en: Use correct loop cursor in error path.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e7 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-30 16:25:14 -04:00
Rafael J. Wysocki
50904a7ddd Merge branches 'acpica', 'acpi-battery' and 'pm-cpuidle' 2015-04-30 21:05:57 +02:00
Linus Torvalds
fb45f493c1 Fix 2 bugs in the request-based DM blk-mq support that was added during
the 4.1 merge.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJVQjzSAAoJEMUj8QotnQNaxOwIAJceb8ih3QGT5+2dcO2lZ0K7
 NZfNvLgJQswg36vvjuLn8rrMXcAnmLSa+aEFrFH5coeGIYAMWaJqA+4vtohQPZPh
 POSGIFkJxtpmWHqLlEZWthCMlZfoC3GhTu+BEWMcryupZpsJaLhiwBsWdA4HoMaE
 tASn1qYK3y3ttFdnqRtfeKE0WFIZrmrEfR+tCMAqkrIEqnwLAY09KHCFHIf8tZjE
 Lg4pOJPAPqxdFZ2vvWPj0671VQVfwuN08iqyemk6jWk3SD9GiB1faezFjXt4Lkgz
 0kqXnkBgBsewheMLH55GgiRYg6ijCDzt55l6NLu0r2ltkSKX3z1qr5zhy/lIjRY=
 =eV73
 -----END PGP SIGNATURE-----

Merge tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper bugfixes from Mike Snitzer:
 "Fix two bugs in the request-based DM blk-mq support that was added
  during the 4.1 merge"

* tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
  dm: only initialize the request_queue once
2015-04-30 09:39:52 -07:00
Linus Torvalds
9263a06a58 TTY/Serial fixes for 4.1-rc2
Here are some small tty/serial driver fixes for 4.1-rc2.
 
 They include some minor fixes that resolve reported issues, and a new
 device quirk.
 
 All have been in linux-next succesfully.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlVCMgMACgkQMUfUDdst+ylmRwCgzADm9JPmMS7DX0g21mfVSeQK
 nI0AoIiYm3HHxu7wma7o3DowGLvuScwt
 =8lGO
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
 "Here are some small tty/serial driver fixes for 4.1-rc2.

  They include some minor fixes that resolve reported issues, and a new
  device quirk.

  All have been in linux-next succesfully"

* tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_pci: Add support for 16 port Exar boards
  serial: samsung: fix serial console break
  tty/serial: at91: maxburst was missing for dma transfers
  serial: of-serial: Remove device_type = "serial" registration
  serial: xilinx: Use platform_get_irq to get irq description structure
  serial: core: Fix kernel-doc build warnings
  tty: Re-add external interface for tty_set_termios()
2015-04-30 09:30:07 -07:00
Linus Torvalds
dcca8de0aa USB fixes for 4.2-rc1
Here are a number of small USB fixes for 4.2-rc2.  They revert one
 problem patch, fix some minor things, and add some new quirks for
 "broken" devices.
 
 All have been in linux-next successfully.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlVCMNMACgkQMUfUDdst+ylQJwCgsGHQVK4YgrIOCpIkXoc+riy1
 VWkAnip86mUGKRej4jrrRvTGvm3maeTj
 =/oWf
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for 4.2-rc2.  They revert one
  problem patch, fix some minor things, and add some new quirks for
  "broken" devices.

  All have been in linux-next successfully"

* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  cdc-acm: prevent infinite loop when parsing CDC headers.
  Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
  usb: chipidea: otg: remove mutex unlock and lock while stop and start role
  uas: Set max_sectors_240 quirk for ASM1053 devices
  uas: Add US_FL_MAX_SECTORS_240 flag
  uas: Allow uas_use_uas_driver to return usb-storage flags
2015-04-30 09:08:53 -07:00
Linus Torvalds
73be174cf5 SH Drivers Updates for v4.1
* Remove test for now unsupported sh7372 SoC
 * Disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with genpd
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVQbqSAAoJENfPZGlqN0++m9cQAKI5XXWiQgzTWPBOGrKcF03u
 wK5uRR4F0WJyt5zEzXECBw3UWNl9EmfrYmf2u6YCtGnKnDldqtlh0ntN/tKNSN0/
 gJ0hxomPjxJTNWqKoN5kl01vK2tAJS6h+hDsjwen0zgKH6bIGyfTWcP9tN55zAyO
 l+PFFWd5wn4GV3qf23YC4UZyA++Q0V9MDN0KCcniVhBwarxmBj6wbQHvz2YvNLpK
 cebyQuuTGs7sGHYhY0Om5w22oGFM74VG1h/NzJi7jKAqEm9+tCLhYMfdUx5IfBWh
 2e3mM1+cABhEwwVxq/82wzoDULSuRYaW8ebKGlO+cSXrGfRbouMvQRdBAUZjLA2P
 Ml6hB4+BBJrammPmFkLlF8KPm5VPH6ITyxdVw+ZUvuxOqs/rLwe1+Wdm0NelHljz
 +Qu2Qv3ImRZbMm5S5dx0bXuAcKYo1s5jRMQXspuzpWJuSMRnhybj9JHH2fweFntH
 5bng9vTcTFnLxId6/EvL7z+3bEu85Ax4LUJ7WerY+xzY3gA59Od+zYSl3ZIhALoE
 363CIxxvl7OS85lHl2OuFj8s3Yx4N3zWxgO7AnxXRjhJ0GwLfoeZ7NXNvXQHIJ7P
 zAgYMugBlhTr0RPH8PEflI4gXFhVm0J7hb9dlcPVwJvKRNyf8upIC/K9fwFToR3D
 GZiWn1y6337eLLyjkJqw
 =jOnx
 -----END PGP SIGNATURE-----

Merge tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas

Pull SH driver updates from Simon Horman:

 - remove test for now unsupported sh7372 SoC

 - disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with
   genpd

* tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  drivers: sh: Remove test for now unsupported sh7372
  drivers: sh: Disable PM runtime for multi-platform r8a73a4 with genpd
  drivers: sh: Disable PM runtime for multi-platform sh73a0 with genpd
2015-04-30 09:07:26 -07:00